Scribd
Upload
89 views2 pages

Fuel Oil Charaterstic

The document provides salient design data for three types of fuel oil characteristics: 1. Heavy furnace oil has a maximum sulfur content of 4.5%, calorific value of around 10,000 KCal/kg, and flash point of 66°C. 2. Low sulfur heavy stock oil has similar characteristics to heavy furnace oil but with a higher flash point of 76°C. 3. Heavy process oil also has maximum 4.5% sulfur content and around 10,000 KCal/kg calorific value, and flash point of 66°C.

Uploaded by

stylishhunterp
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
89 views2 pages

Fuel Oil Charaterstic

The document provides salient design data for three types of fuel oil characteristics: 1. Heavy furnace oil has a maximum sulfur content of 4.5%, calorific value of around 10,000 KCal/kg, and flash point of 66°C. 2. Low sulfur heavy stock oil has similar characteristics to heavy furnace oil but with a higher flash point of 76°C. 3. Heavy process oil also has maximum 4.5% sulfur content and around 10,000 KCal/kg calorific value, and flash point of 66°C.

Uploaded by

stylishhunterp
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd

CLAUSE NO.

SALIENT DESIGN DATA TABLE - 3 FUEL OIL CHARACTERISTICS ----------------------------------------------------------------------------------------------------------------------------Sl. Characteristics Heavy Furnace Low Sulphur Heavy No. Oil grade HV Heavy Stock Petroleum stock (HFO) (LSHS) (HPS) IS-1593-1982 IS-11489-1985 IS-11489-1985 -----------------------------------------------------------------------------------------------------------------------1. 2. Total sulphur content Gross calorific value (KCal/kg) Flash Point (Min) Water content by volume (Max) Sediment by weight (Max) 4.5% Max. of the order of 10,000 66 deg C 1.0% 1.0% Max. of the order of 10,000 76 deg C 1.0% 4.5% Max. of the order of 10,000 66 deg C 1.0%

3. 4.

5.

0.25%

0.25%

0.25%

6.

Asphaltene content by 2.5% weight (Max.) Kinematic viscosity in Centistokes Ash Content by weight (Max.) Acidity (inorganic) Pour Point (Max.) Sodium content Vanadium content Specific heat below pour point (KCal/Kg C) 370 at 50deg C 0.1%

2.5%

2.5%

7.

100 at 100deg C 0.1%

100 at 100deg C 0.1%

8.

9. 10. 11. 12. 13.

Nil 57 deg C 25 ppm

Nil 66 deg C 25ppm 0.65

Nil 72 deg C 100 ppm 25 ppm

MOUDA SUPER THERMAL POWER PROJECT STAGE-II (2X660 MW) STEAM GENERATOR PACKAGE

TECHNICAL SPECIFICATION SECTION-VI BID DOC. NO.: CS-9575/9571/0370/ 0360/9586-102(R)-2

PART-A SUB SECTION-V SALIENT DESIGN DATA

PAGE 7 OF 8

CLAUSE NO.

SALIENT DESIGN DATA TABLE - 4 LIGHT DIESEL OIL CHARACTERISTICS AS PER IS 1460-2000 Characteristics 1. Pour Point (max) LDO 21 deg.C & 12C for Summer and Winter respectively 2.5 to 15.7

2.

Kinematic viscosity in centistokes at 40 deg.C Sediment percent by mass (max) Total sulphur percent by mass (max) Ash percentage by mass (max) Carbon residue (Rans bottom) percent by pass (max.) Acidity in organic Flash point(Min.) - Pensky Martens Copper strip corrosion for 3 hours at 100C Water content, % by volume(max)

4. 5.

0.10 1.8

6. 7.

0.02 1.50

8. 9. 10.

Nil 66 deg.CNot worse than No. 2 0.25

11.

MOUDA SUPER THERMAL POWER PROJECT STAGE-II (2X660 MW) STEAM GENERATOR PACKAGE

TECHNICAL SPECIFICATION SECTION-VI BID DOC. NO.: CS-9575/9571/0370/ 0360/9586-102(R)-2

PART-A SUB SECTION-V SALIENT DESIGN DATA

PAGE 8 OF 8

You might also like