20LK32

20LK62

SERVICE MANUAL
S81Z420LK32//

20LK32 20LK62 COLOR TELEVISION

Chassis No. MSA

20LK32
MODELS 20LK62
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its
original condition and only parts identical to those specified should be used.

CONTENTS
Page
» ELECTRICAL SPECIFICATIONS ......................................................................................................... 1
» IMPORTANT SERVICE SAFETY PRECAUTION ................................................................................. 2
» LOCATION OF USER'S CONTROL ..................................................................................................... 4
» INSTALLATION AND SERVICE INSTRUCTIONS ................................................................................ 5
» CHASSIS LAYOUT ............................................................................................................................. 13
» BLOCK DIAGRAM .............................................................................................................................. 15
» SCHEMATIC DIAGRAMS ................................................................................................................... 20
» PRINTED WIRING BOARD ASSEMBLIES ........................................................................................ 28
» REPLACEMENT PARTS LIST ............................................................................................................ 32
» PACKING OF THE SET ...................................................................................................................... 39

ELECTRICAL SPECIFICATIONS
POWER INPUT ........................................ 110-220 V AC 50/60 Hz SPEAKER
POWER RATING SIZE ........................................................... 9 × 5 cm oval (2pcs.)
20LK32 ................................................................................ 72 W VOICE COIL IMPEDANCE
20LK62 ................................................................................ 79 W 20LK32 ....................................................... 32 ohm at 400 Hz
PICTURE SIZE .......................................... 1,194 cm2 (185sq inch) 20LK62 ......................................................... 4 ohm at 400 Hz
CONVERGENCE ............................................................. Magnetic ANTENNA INPUT IMPEDANCE
SWEEP DEFLECTION .................................................... Magnetic VHF/UHF ..................................................... 75 ohm Unbalanced
FOCUS ............................................................... QPF Electrostatic TUNING RANGES
INTERMEDIATE FREQUENCIES VHF-Channels ............................................................... 2 thru 13
Picture IF Carrier Frequency ..................................... 45.75 MHz UHF-Channels ............................................................ 14 thru 69
Sound IF Carrier Frequency ...................................... 41.25 MHz CATV Channels ........................................................... 1 thru 125
Color Sub-Carrier Frequency .................................... 42.17 MHz
(Nominal)
AUDIO POWER
OUTPUT RATING Specifications are subject to change without
20LK32 ................................... 1.5 + 1.5 W (at 10% distortion) prior notice.
20LK62 ................................... 3.0 + 3.0 W (at 10% distortion)

SHARP CORPORATION
1
 20LK32
20LK62

IMPORTANT SERVICE SAFETY PRECAUTION

Ë Service work should be performed only by qualified service technicians who are thoroughly
familiar with all safety checks and the servicing guidelines which follow:

WARNING X-RADIATION AND HIGH VOLTAGE LIMITS

1. For continued safety, no modification of any circuit 1. Be sure all service personnel are aware of the
should be attempted. procedures and instructions covering X-radiation. The
2. Disconnect AC power before servicing. only potential source of X-ray in current solid state
3. Semiconductor heat sinks are potential shock TV receivers is the picture tube. However, the picture
hazards when the chassis is operating. tube does not emit measurable X-Ray radiation, if
4. The chassis in this receiver has two ground systems the high voltage is as specified in the "High Voltage
which are separated by insulating material. The non- Check" instructions.
isolated (hot) ground system is for the B+ voltage It is only when high voltage is excessive that X-
regulator circuit and the horizontal output circuit. The radiation is capable of penetrating the shell of the
isolated ground system is for the low B+ DC voltages picture tube including the lead in the glass material.
and the secondary circuit of the high voltage The important precaution is to keep the high voltage
transformer. below the maximum level specified.
To prevent electrical shock use an isolation 2. It is essential that servicemen have available at all
transformer between the line cord and power times an accurate high voltage meter.
receptacle, when servicing this chassis. The calibration of this meter should be checked
periodically.
SERVICING OF HIGH VOLTAGE SYSTEM 3. High voltage should always be kept at the rated value
−no higher. Operation at higher voltages may cause
AND PICTURE TUBE
a failure of the picture tube or high voltage circuitry
When servicing the high voltage system, and;also, under certain conditions, may produce
remove the static charge by connecting a radiation in exceeding of desirable levels.
4. When the high voltage regulator is operating properly
10k ohm resistor in series with an insulated
there is no possibility of an X-radiation problem. Every
wire (such as a test probe) between the pic- time a color chassis is serviced, the brightness should
ture tube ground and the anode lead. (AC be tested while monitoring the high voltage with a
line cord should be disconnected from AC meter to be certain that the high voltage does not
outlet.) exceed the specified value and that it is regulating
correctly.
1. Picture tube in this receiver employs integral implosion 5. Do not use a picture tube other than that specified or
protection. make unrecommended circuit modifications to the
2. Replace with tube of the same type number for high voltage circuitry.
continued safety. 6. When trouble shooting and taking test measurements
3. Do not lift picture tube by the neck. on a receiver with excessive high voltage, avoid being
4. Handle the picture tube only when wearing unnecessarily close to the receiver.
shatterproof goggles and after discharging the high Do not operate the receiver longer than is necessary
voltage anode completely. to locate the cause of excessive voltage.

2
 20LK32
20LK62

IMPORTANT SERVICE SAFETY PRECAUTION

(Continued)

BEFORE RETURNING THE RECEIVER • Connect the resistor connection to all exposed metal
parts having a return to the chassis (antenna, metal
(Fire & Shock Hazard) cabinet, screw heads, knobs and control shafts,
Before returning the receiver to the user, perform escutcheon, etc.) and measure the AC voltage drop
the following safety checks. across the resistor.
AII checks must be repeated with the AC ine cord
1. Inspect all lead dress to make certain that leads are plug connection reversed. (If necessary, a non-
not pinched or that hardware is not lodged between polarized adapter plug must be used only for the
the chassis and other metal parts in the receiver. purpose of completing these check.)
2. Inspect all protective devices such as non-metallic Any current measured must not exceed 0.5 milliamp.
control knobs, insulating materials, cabinet backs, Any measurements not within the limits outlined
adjustment and compartment covers or shields, above indicate of a potential shock hazard and
isolation resistor-capacity networks, mechanical corrective action must be taken before returning the
insulators and etc. instrument to the customer.
3. To be sure that no shock hazard exists, check for
leakage current in the following manner.
• Plug the AC cord directly into a 110~220 volt AC
outlet, (Do not use an isolation transformer for this
test).
• Using two clip leads, connect a 1.5k ohm, 10 watt
resistor paralleled by a 0.15µF capacitor in series with
all exposed metal cabinet parts and a known earth
ground, such as electrical conduit or electrical ground
connected to earth ground.
• Use an AC voltmeter having with 5000 ohm per volt,
or higher, sensitivity to measure the AC voltage drop
across the resistor. 1.5k ohm
10W

0.15µF
TEST PROBE

TO EXPOSED CONNECT TO
METAL PARTS KNOWN EARTH
GROUND
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212

SAFETY NOTICE
Many electrical and mechanical parts in television For continued protection, replacement parts must be
receivers have special safety-related characteristics. identical to those used in the original circuit. The use of
These characteristics are often not evident from visual substitute replacement parts which do not have the same
inspection, nor can protection afforded by them be safety characteristics as the factory recommended
necessarily increased by using replacement components replacement parts shown in this service manual, may
rated for higher voltage, wattage, etc. create shock, fire, X-radiation or other hazards.
Replacement parts which have these special safety
characteristics are identified in this manual; electrical
components having such features are identified by "å"
and shaded areas in the Replacement Parts Lists and
Schematic Diagrams.
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212

3
20LK32
20LK62

LOCATION OF USER'S CONTROL

Front Panel
(20LK32)

VIDEO/AUDIO IN TERMINALS
(VIDEO/AUDIO terminals are also
provided on the rear.)

(20LK62)

VIDEO/AUDIO IN2 TERMINALS

POWER
Press → On.
Press again → Off. CHANNEL UP/DOWN
(') Selects next higher channel.
(") Selects next lower channel.
ON TIMER indicator.

SENSOR AREA FOR VOLUME UP/DOWN

REMOTE CONTROL (+) Increases sound.
(–) Decreases sound.

MENU
Press ; Accesses MAIN MENU.
Press again ; Exits MAIN MENU.

Basic Remote Control Functions

Infrared Transmitter Window

POWER INPUT
Press → On. Press → Switch to external video input
Press again → Off. mode.
Press again → Switch to TV mode.
REMOTE KEYPAD (20LK32)
Accesses any channel from keypad.
Press → Switch to external video
FLASHBACK INPUT 1 mode.
Returns to previous channel. Press 2 times → Switch to external
video INPUT 2 mode.
VOLUME UP/DOWN Press 3 times → Switch back to the
(+) Increases sound. original TV mode. (20LK62)
(–) Decreases sound.
• In menu mode, changes or selects
the TV adjustments. CHANNEL UP/DOWN
(') Selects next higher channel.
MUTE (") Selects next lower channel.
Press → Mutes sound. • Moves the “ ” mark of the MENU
Press again → Restores sound. screen.
• CLOSED CAPTION appears when
sound is muted.
MENU
Press → Accesses MAIN MENU.
Press again → Exits MAIN MENU.

DISPLAY
Press → Displays receiving channel for
4 seconds.
Press again→ Display Clock
TV
Press again→ Removes display.
• Temporarily displays receiving
channel when in Closed Caption
mode.

4
 20LK32
20LK62

INSTALLATION AND SERVICE INSTRUCTIONS

Note: (1) When performing any adjustments to resistor controls and transformers use non-metallic
screwdrivers or TV alignment tools.
(2) Before performing adjustments, the TV set must be on at least 15 minutes.

CIRCUIT PROTECTION HIGH VOLTAGE CHECK

The receiver is protected by a 3.15A fuse (F701), High voltage is not adjustable but must be checked
mounted on PWB-A, wired into one side of the AC to verify that the receiver is operating within safe
line input. and efficient design limitations as specified checks
should be as follows:
+B DC REGULATOR CONFIRMATION
The + B DC output voltage adjustment is not included 1. Connect an accurate high voltage meter between
in this circuit.However, should confirmation be ground and anode of picture tube.
reguired proceed as follows. 2. Operate receiver for at least 15 minutes at 110~220V
AC line voltage, with a strong air signal or a properly
1. Actuate receiver with 220V AC input voltage. tuned in test signal.
2. Receive a local channel. 3. Receve a good local channel.
3. Connect positive lead of digital voltmeter to C754 4. The voltage should be approximately, 25.5kV (at
positive side on PWB-A ; negative lead to chassis pictuer MAX Bright center condition).
ground. If a correct reading cannot be obtained, check circuitry
4. Confirm this voltage reading is as below. for malfunctioning components.
CAUTION: The reading should be within +130.0 ± 2.0V
DC to ensure normal function and circuitry
reliability.

X-RADIATION PROTECTOR CIRCUIT TEST

After service has been performed on the horizontal
deflection system, high voltage system, B+ system,
test the X-Radiation protection circuit to ascertain
proper operation as follows:

1. Apply 220V AC using a variac transformer for accurate

input voltage.
2. Allow for warm up and adjust all customer controls
for normal picture and sound.
3. Receive a good local channel.
4. Connect a digital voltmeter to TP653 and make sure
that the voltmeter reads 21.4 ± 1.5 V.
5. Apply external 27.9V DC at TP653 by using an
external DC supply, TV must be shut off.
6. To reset the protector, unplug the AC cord and make
a short circuit between TP651 and TP652. Now make
sure that normal picture appears on the screen.
7. If the operation of the horizontal oscillator does not
stop in step 5, the circuit must be repaired before the
set is returned to the customer.

5
20LK32
20LK62

For adjustments of this model, the bus data is converted to various analog signals by the D/A converter
circuit.

Note: There are still a few analog adjustments in this series such as focus and master screen voltage.
Follow the steps below whenever the service adjustment is required. See "Table-B" to determine, if serv-
ice adjustments are required.

1. Service mode To enter the service mode and exit serv-

Before putting unit into the service mode, check that ice mode.
customer adjustments are in the normal mode. Use
the reset function in the video adjustment menu to Make a short circuit JA137 & JA138 for 1 second and
ensure customer controls are in their proper (reset) release to switch to the service mode position, and the
position. microprocessor is in input mode.(Adjustment through the
I2C bus control.)
2. Service item selection To exit the service mode, turn the television off by
Once in the service mode, press the Ch-up or Ch- pressing the power button.
down button on the remote controller or at the set.
The service adjustment item will vary in increments
of one. Select the item you wish to adjust.

3. Data number selection

Press the Vol-up or down button to adjust the data
number.

SERVICE ADJUSTMENT ITEM DATA NUMBER

AGC: 25

Figure A.

6
 20LK32
20LK62

SERVICE MODE
(1) In the Service Mode, Key is used to select the mode in the following order.

AGC & WHITE POINT SUB

GEOMETRIC ADJ. ADJ.
MODE MODE MODE

OFFSET
ADJ.
MODE

FEATURE IC MTS
OPTION OPTION ADJ.
MODE MODE MODE

AGC & WHITE POINT SUB

GEOMETRIC ADJ. ADJ.
MODE MODE MODE
↓ ↓ ↓
AGC TAKE OVER POINT (AGC) W.P. RED OFFSET HIGH / MAX VOLUME (SUB-VOL)
↓ OFFSET BLUE TONE (DRI-R-HI) ↓
VERTICAL SLOPE (V-LIN) ↓ SUB CONTRAST (SUB-CON)
↓ W.P. GREEN OFFSET HIGH / ↓
VERTICAL AMP (V-AMP) OFFSET BLUE TONE (DRI-G-HI) SUB TINT (SUB-TINT)
↓ ↓ ↓
VERTICAL SHIFT (V-CENT) W.P.BLUE OFFSET HIGH / SUB COLOUR (SUB-COL)
↓ OFFSET BLUE TONE (DRI-B-HI) ↓
VERTICAL ZOOM (V-ZOOM) ↓ SUB BRIGHTNESS (SUB-BRI)
↓ W.P. RED MH / STD (DRI-R-MH) ↓
HORIZONTAL SHIFT (H-CENT) ↓ SUB SHARPNESS (SUB-SHP)
↓ W.P. GREEN MH / STD (DRI-G-MH) ↓
EAST-WEST WIDTH (H-SIZE) ↓ MAX HOTEL VOLUME (HTL-VOL)
↓ W.P. BLUE MH / STD (DRI-B-MH) ↓
HORIZONTAL PARALLELOGRAM (EW//) ↓ HOTEL PROGRAM NO(HTL-PRG)
↓ W.P. RED OFFSET ML / ↓
EAST-WEST PARABOLA / WIDTH (PARA) OFFSET RED TONE (DRI-R-ML) BLUE BACK CONTRAST (BB-CON)
↓ ↓ ↓
EAST-WEST UPPER CORNER W.P. GREEN OFFSET ML / OSD GRB REFERENCE (RGB)
PARABOLA (COR(U)) OFFSET RED TONE (DRI-G-ML) ↓
↓ ↓ BLACK LEVEL OFFSET R(CUT-R)
EAST-WEST LOWER CORNER W.P. BLUE OFFSET ML / ↓
PARABOLA (COR(L)) OFFSET RED TONE (DRI-B-ML) BLACK LEVEL OFFSET G(CUT-G)
↓ ↓ ↓
EAST-WEST TRAPEZIUM (TRAPE) W.P. RED OFFSET LOW (DRI-R-LO) CATHODE DRIVE LEVEL(CDL)
↓ ↓
HORIZONTAL BOW (HB) W.P. GREEN OFFSET LOW (DRI-G-LO)
↓ ↓
S-CORRECTION (S-COR) W.P. BLUE OFFSET LOW (DRI-B-LO)

7
20LK32
20LK62

OFFSET MTS
ADJ. ADJ.
MODE MODE
↓ ↓
Y-D TIME (TV) [ YD ] (DL-TV) ATTENUATE INPUT SIGNAL LEVEL (ATT)
↓ ↓
Y-D TIME (AV) [ YD ] (DL-AV) VCO FREE RUNNING FREQUENCY ADJ. (VCO)
↓ ↓
INITIAL/DEFAULT LANGUAGE (INIT) STEREO, SAP, DBX FILTER ADJ. (FILTER)
↓ ↓
FAO-MAX VOLUME (FAO-VOL) STEREO SEPARATION ADJUSTMENT (300HZ) (WIDEBAND)
↓ ↓
ENERGY SAVE OFFSET (ESV_OFFS) STEREO SEPARATION ADJUSTMENT (3kHZ) (SPECTRAL)
↓ ↓
CLOSE CAPTION POSITION (CCPOS) BASS LEVEL (BASS)
↓
TREBLE LEVEL (TREBLE)

IC FEATURE
OPTION OPTION
MODE MODE
↓ ↓
VERTICAL SCAN DISABLE (VSD) V-CHIP (V-CHIP)
↓ ↓
BLACK STRETCH (BKS) MTS DECODING ENABLED (MTS)
↓ ↓
AUTOMATIC VOLUME LEVELLING (AVL) DEMO MODE (DEMO)
↓ ↓
FAST FILTER IF-PLL ( FFI ) REAL TIME CLOCK / ON TIMER (CLOCK)
↓ ↓
ENABLE VERTICAL GUARD ( EVG ) ENERGY SAVE (E-SAVE)
↓ ↓
EHT TRACKING MODE ( EHT ) PERSONAL PREFERENCE PROGRAM (P_PREF)
↓ ↓
OVERSCAN SWITCH OFF (OSO) UNIVERSAL PLUS (UNIV+)
↓ ↓
AUTO COLOUR LIMIT (ACL) SPEAKER ON/OFF (SPEAKER)
↓ ↓
FORCED COLOUR-ON (FCO) FIXED AUDIO OUT (FAO)
↓ ↓
VIDEO MUTE AT IDENT LOSS (VMI) VIEW TIMER (VIEW-TM)
↓ ↓
VIDEO MUTE AT PROGRAM/SOURCE CHANGE (VMC) FRENCH LANGUAGE (FRENCH)
↓ ↓
HOTEL MODE (HTL) EZ SETUP / AUTOPRESET (EZ-SETUP)
↓ ↓
GAIN FM DEMODULATOR (BTSC) WHITE TEMP OR FAVORITE COLOR (W-TEMP)
↓ ↓
CHARGE PUMP (CP) AV ENABLED OR DISABLED (AV)
↓ ↓
FM WINDOW SELECTION (FMWS) AV2 ENABLED OR DISABLED (AV2)
↓ ↓
SOUND MUTE BIT 0 (SM0) DYNAMIC SKIN CONTROL (DSK)
↓ ↓
SOUND MUTE BIT 1 (SM1) RATIO PRE- AND OVERSHOOT BIT 0 (RPO0)
↓ ↓
IF AGC SPEED BIT 0 (AGC0) RATIO PRE- AND OVERSHOOT BIT 1 (RPO1)
↓ ↓
IF AGC SPEED BIT 1 (AGC1) GAIN FM DEMODULATOR (AGN)
↓ ↓
PHI 1 TIME CONSTANT FOR FE (FOA-FE) AUTO SWITCH OFF ENABLED (AUTO-OFF)
↓
PHI 1 TIME CONSTANT FOR FE (FOB-FE)
↓
PHI 1 TIME CONSTANT FOR AV (FOA-AV)
↓
PHI 1 TIME CONSTANT FOR AV (FOB-AV)
↓
FORCED SLICING LEVEL FOR VERTICAL SYNC.(FSL)
↓ FORWARD : CH DOWN KEY
SYNCHRONISATION OF OSD/TEXT DISPLAY (HP2)
↓ REVERSE : CH UP KEY
RGB BLANK (RGBL) ( ) means OSD display.

Figure B: ADJUSTMENT CATEGORIES

1Press the CH DOWN/UP key on the remote controller to get ready to select the mode one by one.
2Press the CH DOWN/UP key on the remote controller to select the modes reversibly one by one.
3Using the VOLUME UP/DOWN key on the remote controller, the data can be modified.
(OSD disturbance can be erased by R/C display key)

8
 20LK32
20LK62

SERVICE MODE
SERVICE DATA
ADJUST ITEM REMARK
POSITION RANGE INITIAL VALUE FIX/ADJ
AGC AGC TAKE OVER POINT 0 ~ 63 14 ADJ
V-LIN VERTICAL SLOPE 0 ~ 63 32 ADJ
V-AMP VERTICAL AMP 0 ~ 63 32 ADJ
V-CENT VERTICAL SHIFT 0 ~ 63 32 ADJ
V-ZOOM VERTICAL ZOOM 0 ~ 63 32 FIX
H-CENT HORIZONTAL SHIFT 0 ~ 63 32 ADJ
H-SIZE EAST-WEST WIDTH 0 ~ 63 32 FIX
EW// HORIZONTAL PARALLELOGRAM 0 ~ 63 32 FIX
PARA EAST-WEST PARABOLA / WIDTH 0 ~ 63 32 FIX
COR(U) EAST-WEST UPPER CORNER PARABOLA 0 ~ 63 32 FIX
COR(L) EAST-WEST LOWER CORNER PARABOLA 0 ~ 63 32 FIX
TRAPE EAST-WEST TRAPEZIUM 0 ~ 63 32 FIX
HB HORIZONTAL BOW 0 ~ 63 32 FIX
S-COR S-CORRECTION 0 ~ 63 0 FIX Must be "17"
DRI-R-HI W.P. RED OFFSET HIGH / OFFSET BLUE TONE 0 ~ 63 32 FIX Must be "32"
DRI-G-HI W.P. GREEN OFFSET HIGH / OFFSET BLUE TONE 0 ~ 63 32 FIX Must be "33"
DRI-B-HI W.P. BLUE OFFSET HIGH / OFFSET BLUE TONE 0 ~ 63 32 FIX Must be "37"
DRI-R-MH W.P. RED MH / STD 0 ~ 63 25 FIX Must be "32"
DRI-G-MH W.P. GREEN MH / STD 0 ~ 63 32 ADJ
DRI-B-MH W.P. BLUE MH / STD 0 ~ 63 32 ADJ
DRI-R-ML W.P. RED OFFSET ML / OFFSET RED TONE 0 ~ 63 32 FIX Must be "32"
DRI-G-ML W.P. GREEN OFFSET ML / OFFSET RED TONE 0 ~ 63 32 FIX Must be "32"
DRI-B-ML W.P. BLUE OFFSET ML / OFFSET RED TONE 0 ~ 63 32 FIX Must be "25"
DRI-R-LO W.P. RED OFFSET LOW 0 ~ 63 32 FIX Must be "32"
DRI-G-LO W.P. GREEN OFFSET LOW 0 ~ 63 32 FIX Must be "22"
DRI-B-LO W.P. BLUE OFFSET LOW 0 ~ 63 32 FIX Must be "19"
SUB-VOL MAX VOLUME 0 ~ 63 63 FIX Must be "63"
SUB-CON SUB CONTRAST 0 ~ 63 63 FIX Must be "54"
SUB-COL SUB COLOUR 0 ~ 63 32 ADJ
SUB-BRI SUB BRIGHTNESS 0 ~ 63 32 ADJ
SUB-TINT SUB TINT 0 ~ 63 32 ADJ
SUB-SHP SUB SHARPNESS 0 ~ 63 32 FIX Must be "27"
HTL-VOL MAX HOTEL VOLUME 0 ~ 63 32 FIX
HTL-PRG HOTEL PROGRAM NO 0~125 or >125 for none 255 FIX
BB-CON BLUE BACK CONTRAST 0 ~ 15 10 FIX Must be "5"
RGB OSD GRB REFERENCE 0 ~ 15 15 FIX Must be "5"
CUT-R BLACK LEVEL OFFSET R 0 ~ 63 32 ADJ
CUT-G BLACK LEVEL OFFSET G 0 ~ 63 32 ADJ
CDL CATHODE DRIVE LEVEL 0 ~ 15 0 FIX Must be "4"
DL-TV Y-D TIME (TV) [ YD ] 0 ~ 15 12 FIX Must be "2"
DL-AV Y-D TIME (AV) [ YD ] 0 ~ 15 12 FIX Must be "8"
INIT INITIAL/DEFAULT LANGUAGE 0(English), 1(Spanish), 0 FIX Must be "1"
2(French)
FAO-VOL FAO-MAX VOLUME 0 ~ 63 63 FIX Must be "63"
ESV_OFFS ENERGY SAVE OFFSET 0 ~ 63 10 FIX Must be "20"
CCPOS CLOSE CAPTION POSITION 0 ~ 255 32 ADJ
ATT ATTENUATE INPUT SIGNAL LEVEL 0 ~ 15 10 FIX* 
VCO VCO FREE RUNNING FREQUENCY ADJ. 0 ~ 63 32 FIX* 
FILTER STEREO, SAP, DBX FILTER ADJ. 0 ~ 63 28 FIX*  20LK32=FIX
WIDEBAND STEREO SEPARATION ADJUSTMENT (300Hz) 0 ~ 63 32 FIX*  20LK62=ADJ
SPECTRAL STEREO SEPARATION ADJUSTMENT (3kHz) 0 ~ 63 27 FIX* 
BASS BASS LEVEL 0 ~ 15 8 FIX
TREBLE TREBLE LEVEL 0 ~ 15 8 FIX
VSD VERTICAL SCAN DISABLE 0 or 1 when item selected 0 FIX
BKS BLACK STRETCH 0(disable) or 1(enable) 1 FIX
AVL AUTOMATIC VOLUME LEVELLING 0(disable) or 1(enable) 1 FIX
FFI FAST FILTER IF-PLL 0(disable) or 1(enable) 0 FIX
EVG ENABLE VERTICAL GUARD 0(disable) or 1(enable) 1 FIX
EHT EHT TRACKING MODE 0(disable) or 1(enable) 1 FIX
OSO OVERSCAN SWITCH OFF 0(disable) or 1(enable) 0 FIX
ACL AUTO COLOUR LIMIT 0(disable) or 1(enable) 0 FIX
FCO FORCED COLOUR-ON 0(disable) or 1(enable) 0 FIX
VMI VIDEO MUTE AT IDENT LOSS 0(disable) or 1(enable) 1 FIX
VMC VIDEO MUTE AT PROGRAM/SOURCE CHANGE 0(disable) or 1(enable) 1 FIX
HTL HOTEL MODE 0(disable) or 1(enable) 0 FIX
BTSC GAIN FM DEMODULATOR 0(disable) or 1(enable) 0 FIX
CP CHARGE PUMP 0(fast tuning) or 1 0 FIX
(moderate speed tuning)

Table - A
9
 20LK32
20LK62

SERVICE DATA
ADJUST ITEM REMARK
POSITION RANGE INITIAL VALUE FIX/ADJ
FMWS FM WINDOW SELECTION 0(disable) or 1(enable) 0 FIX
SM0 SOUND MUTE BIT 0 (SM0) 0(disable) or 1(enable) 1 FIX
SM1 SOUND MUTE BIT 1 0(disable) or 1(enable) 0 FIX
AGC0 IF AGC SPEED BIT 0 0(disable) or 1(enable) 1 FIX
AGC1 IF AGC SPEED BIT 1 0(disable) or 1(enable) 0 FIX
FOA-FE PHI 1 TIME CONSTANT FOR FE 0(disable) or 1(enable) 0 FIX
FOB-FE PHI 1 TIME CONSTANT FOR FE 0(disable) or 1(enable) 0 FIX
FOA-AV PHI 1 TIME CONSTANT FOR AV 0(disable) or 1(enable) 1 FIX
FOB-AV PHI 1 TIME CONSTANT FOR AV 0(disable) or 1(enable) 1 FIX
FSL FORCED SLICING LEVEL FOR VERTICAL SYNC. 0(disable) or 1(enable) 0 FIX
HP2 SYNCHRONISATION OF OSD/TEXT DISPLAY 0(disable) or 1(enable) 0 FIX
RGBL RGB BLANK 0(disable) or 1(enable) 0 FIX
V-CHIP V-CHIP 0(disable) or 1(enable) 0 FIX
MTS MTS DECODING ENABLED 0(disable) or 1(enable) 0 FIX* 20LK32→0/20LK62→1
DEMO DEMO MODE 0(disable) or 1(enable) 1 FIX
CLOCK REAL TIME CLOCK / ON TIMER 0(disable) or 1(enable) 1 FIX Must be "1"
E-SAVE ENERGY SAVE 0(disable) or 1(enable) 1 FIX
P_PREF PERSONAL PREFERENCE PROGRAM 0(disable) or 1(enable) 0 FIX
UNIV+ UNIVERSAL PLUS 0(disable) or 1(enable) 0 FIX
SPEAKER SPEAKER ON/OFF 0(disable) or 1(enable) 0 FIX
FAO FIXED AUDIO OUT 0(disable) or 1(enable) 0 FIX
VIEW-TM VIEW TIMER 0(disable) or 1(enable) 1 FIX Must be "1"
FRENCH FRENCH LANGUAGE 0(disable) or 1(enable) 0 FIX
EZ-SETUP EZ SETUP / AUTOPRESET 0(AUTOPRESET) or 1 FIX
1(EZ SETUP)
W-TEMP WHITE TEMP OR FAVORITE COLOR 0(FC) or 1(WT) 0 FIX
AV AV ENABLED OR DISABLED 0(without ext. source) or 0 FIX
1(with external source)
AV2 AV2 ENABLED OR DISABLED 0(1 input) or 1(2 input) 0 FIX* 20LK32→0/20LK62→1
DSK DYNAMIC SKIN CONTROL 0(disable) or 1(enable) 0 FIX
RPO0 RATIO PRE- AND OVERSHOOT BIT 0 0(disable) or 1(enable) 0 FIX
RPO1 RATIO PRE- AND OVERSHOOT BIT 1 0(disable) or 1(enable) 0 FIX
AGN GAIN FM DEMODULATOR 0(normal) or 1(+6dB) 0 FIX
AUTO-OFF AUTO SWITCH OFF ENABLED 0(disable) or 1(enable) 1 FIX
PON-CH POWER ON WITH LOCAL PROGRAM KEYS 0(disable) or 1(enable) 0 FIX

Table - A

Holding down to short JA137 & JA138 and turn on the main power SW will automatically write the initial values into
IC1003.
This is only can done when a new EEPROM is used. (Judge with the first 4 bytes.)

ADJUSTMENT
PART REPLACED NOTES
NECESSARY UNNECESSARY
IC801 X Data is stored in IC1003.

Holding down to short JA137 & JA138 and turn on the main
IC1003 power SW will automatically write the initial values into IC1003.
X
This is only can done when a new EEPROM is used. (Judge
with the first 4 bytes.)

CRT X Adjust items related to picture tube only.

Table - B

10
 20LK32
20LK62

Ë SERVICE ADJUSTMENT
RF AGC Adjustment
1. Receive a good local channel.
2. Enter the service mode signal category and select
the service adjustment "AGC".
3. Set the data value to point where no noise or beat
appears.
4. Select another channel to confirm that no noise or
beat appears.

CHROMA ADJUSTMENT
No. Adjusting point Adjusting procedure/conditions Waveform and others
WAVEFORM 1 FINAL WAVEFORM
1 SUB-TINT (I2C 1. Receive the "Colour Bar" signal through AV in.
BUS CON- 2. Connect the oscilloscope to TP853 (Pin (5) of SAME LEVEL

TROL) P882) BLUE-OUT.

» Range : 100mV/div. (AC)(Use Probe 10:1)
» Sweep time : 10 µsec/div.
3. Call the "SUB-TINT" mode in service mode. Ad-
just the "SUB-TINT" bus data to obtain the wave- W Y CY G MG R B

form shown as Fig 1. Fig 1 Fig 2

4. "SUB-TINT" bus data decrease 4 steps to get fi-
nal waveform. (Fig 2.)
5. Clear the SERVICE mode.

HORIZONTAL AND VERTICAL DEFLECTION LOOP ADJUSTMENT

No. Adjusting point Adjusting procedure/conditions Waveform and others
1 V-SLOPE(I2C 1. Receive the "Monoscope Pattern" signal.
BUS CON- 2. Call the "V-LIN" mode.
TROL) 3. Increase or decrease "V-LIN" by Volume key till
the horizontal line in the center of monoscope is
just at the position where the blanking starts.

2 V-CENTER (I2C 1. Call the "V-CENT" mode.

BUS CON- 2. Increase or decrease "V-CENT" by Volume key till
TROL) the picture is centered.

3 V - AMP (I2C 1. Call the "V-AMP" mode.

BUS CON- 2. Increase or decrease "V - AMP" by Volume key to
TROL) set overscan of 10.0% typical.
Adjustment Spec 10.0% range ±1%.

4 S-CORREC-
TION (I2C BUS FIXED DATA, NO NEED TO ADJUST.
CONTROL)

5 H - CENTER 1. Call the "H-CENT" mode.

2. Increase or decrease "H-CENT" by Volume key
to center the picture horizontal.
6 Focus 1. Receive the "Monoscope Pattern" signal.
adjustment 2. Press R/C to set Picture NORMAL condition.
3. Adjust the focus control to get the best focus.

11
20LK32
20LK62

CRT CUT-OFF, BACKGROUND AND SUB-CONTRAST ADJUSTMENT

No. Adjusting point Adjusting procedure/conditions Waveform and others
1 CRT CUTOFF 1. Switch TV to VIDEO mode, BLUE BACK OFF, with
ADJUSTMENT NO VIDEO signal. 3.5Vdc
(I2C BUS 2. Press R/C to set Picture Normal condition.
CONTROL) 3. Connect the oscilloscope to Red OUT from
IC801.(TP47R)

Range : 1 V/Div (DC)

Sweep : 5 msec/Div
1V
4. Adjust SCREEN VR ,so that the tip of signal reach
0
3.5 Vdc + 0.1 Vdc.

2 SUB-BRIGHT- 1. Call "SUB-BRI" in service mode. (Receive Cross-

NESS hatch pattern with 5 black level windows)
ADJUSMENT 2. Adjust the "SUB BRIGHT" bus data in order that
(I2C BUS the line 1, 2 and 3 have the same darkness
CONTROL) wherelse line 4 is slightly brighter than line 1, 2 1 2 3 4 5
and 3 and finally line 5 will be the brighter than
line 4. 1, 2, 3 are in same black level.

3 WHITE BAL- 1. Receive the "Monoscope Pattern" signal. # 11,600° K X : 0.273

ANCE SERV- 2. Press R/C to set Picture NORMAL condition. Y : 0.280
ICE MODE 3. Connect the DC miliammeter between the TP 602
ADJ. (I2C BUS ( - ) TP 603 ( + ). ( MINOLTA COLOUR ANALYZER
CONTROL) 4. Check Beam current should be around (990µA) CA-100)
5. Set it to service mode and adjust the DRI-G-MH, *NOTE: Above DATA can be UP/
& DRI-B-MH data to have a colour temperature DOWN by volume key.
of 11,600°K ( white ).
6. Receive "WHITE" pattern, WITH BURST signal, LOW HIGH
and set BRIGHTNESS Y by generator, to ** 10 20" 1.8cd/m2 115cd/m2
cd/m2 (MINOLTA CA-100) by reducing LUMINATE
Y signal. * 11,600° K
7. Adjust "CUT-R" & "CUT-G" to get 11,600°K. Then DRI-GW="DRI-GS"DATA-5
go back NORMAL mode (HIGH BRIGHT**) to DRI-BW="DRI-BS" DATA-5
check colour temperature. If out of range, back to
(1).

Note: This adjustment must be done after

warming up the unit for 30 minutes or
longer with a beam current over 500µA.
DRI-R-MH=32 (FIXED)
DRI-G-MH=33 (FIXED)
DRI-B-MH=37 (FIXED)
DRI-R-MH=32 (FIXED)

4 Maximum 1. Receive the "Monoscope Pattern" signal.

beam check 2. Press R/C to set Picture NORMAL condition.
3. Connect the DC miliammeter between TP603 (+)
and TP602 (–).
(Full Scale: 3 mA Range)
4. Beam current must be within 990 ± 50 µA.

12
 20LK32
20LK62

MODEL 20LK32 CHASSIS LAYOUT

H

1 2 3 4 5 6

13
20LK32
20LK62

MODEL 20LK62 CHASSIS LAYOUT

H

1 2 3 4 5 6

14
 20LK32
20LK62

BLOCK DIAGRAM-1
H

1 2 3 4 5 6

15
 20LK32
20LK62

MODEL 20LK32 BLOCK DIAGRAM-2

H

1 2 3 4 5 6 7 8 9 10 11 12

16 17
 20LK32
20LK62

MODEL 20LK62 BLOCK DIAGRAM-2

H

1 2 3 4 5 6 7 8 9 10 11 12

18 19
 20LK32
20LK62

DESCRIPTION OF SCHEMATIC DIAGRAM

NOTES: WAVEFORM MEASUREMENT CONDITIONS:
1. The unit of resistance "ohm" is omitted. 1. Photographs taken on a standard gated color bar
(K=kΩ=1000Ω, M=MΩ) signal, the tint setting adjusted for proper color. The
2. All resistors are 1/16 watt, unless otherwise noted. wave shapes at the red, green and blue cathodes of
3. All capacitors are µ F, unless otherwise noted. the picture tube depend on the tint, color level and
(P=pF=µµF) picture control.
4. (G) indicates ±2% tolerance may be used. 2. indicates waveform check points (See chart,
5. indicates line isolated ground. waveforms are measured from point indicated to
6. indicates hot ground. chassis ground.)

VOLTAGE MEASUREMENT CONDITIONS: å AND SHADED ( ) COMPONENTS

1. All DC voltages are measured with DVM connected = SAFETY RELATED PARTS.
between points indicated and chassis ground, line ' MARK= X-RAY RELATED PARTS.
voltage set at 120V AC and all controls set for normal
picture unless otherwise indicated. This circuit diagram is a standard one, printed circuits
2. All voltages measured with 1000µ V B & W or Color may be subject to change for product improvement
signal. without prior notice.

WAVEFORMS
1 1.0 Vp-p 2 2.8 Vp-p 3 2.6 Vp-p 4 2.7 Vp-p 5 65.0 Vp-p

Horiz. Rate Horiz. Rate Horiz. Rate Horiz. Rate Horiz. Rate

6 67.0 Vp-p 7 80.0 Vp-p 8 3.0 Vp-p 9 2.3 Vp-p 0 116.0 Vp-p

Horiz. Rate Horiz. Rate Vert. Rate Horiz. Rate Horiz. Rate

q 8.4 Vp-p w 40.8 Vp-p e 98.0 Vp-p r 1,160 Vp-p t 415.0 Vp-p

Horiz. Rate Vert. Rate Horiz. Rate Horiz. Rate Power Supply Rate

20
 20LK32
20LK62

SCHEMATIC DIAGRAM: CRT Unit

H

1 2 3 4 5 6

21
 20LK32
20LK62

MODEL 20LK32 SCHEMATIC DIAGRAM: MAIN Unit

H

1 2 3 4 5 6 7 8 9 10 11 12

22 23
 20LK32
20LK62

MODEL 20LK62 SCHEMATIC DIAGRAM: MAIN Unit

H

1 2 3 4 5 6 7 8 9 10 11 12

24 25
 20LK32
20LK62

MODEL 20LK62 SCHEMATIC DIAGRAM: MTS MODULE Unit

H

1 2 3 4 5 6 7 8 9 10 11 12

26 27
20LK32
20LK62

PRINTED WIRING BOARD ASSEMBLIES

H

PWB-A: MAIN Unit (Wiring Side)

1 2 3 4 5 6

28
 20LK32
20LK62

PWB-A: MAIN Unit (Chip Parts Side)

1 2 3 4 5 6

29
20LK32
20LK62

E PWB-B: CRT Unit (Wiring Side)

A
PWB-B: CRT Unit (Chip Parts Side)

1 2 3 4 5 6

30
 20LK32
20LK62

E PWB-E: MTS MODULE Unit (Wiring Side)

(Only for 20LK62)

A
PWB-E: MTS MODULE Unit (Chip Parts Side)
(Only for 20LK62)

1 2 3 4 5 6

31
20LK32
20LK62

Ref. No.
PARTS LIST
Part No. ★ Description Code Ref. No. Part No. ★ Description Code

PWB-A: DUNTK541WEA2 (20LK32)

PARTS REPLACEMENT PWB-A: DUNTK541WEA3 (20LK62)
Replacement parts which have these special safety characteristics MAIN UNIT
identified in this manual; electrical components having such features
are identified by å and shaded areas in the Replacement Parts Lists TUNER
and Schematic Diagrams. The use of a substitute replacement part NOTE: THE PARTS HERE SHOWN ARE SUPPLIED AS AN
ASSEMBLY BUT NOT INDEPENDENTLY.
which does no have the same safety characteristic as the factory
å TU201 VTUENV56D82-1 J Tuner AZ
recommended replacement parts shown in this service manual may or
create shock, fire or other hazards. VTUVTSTSUF770

"HOW TO ORDER REPLACEMENT PARTS" INTEGRATED CIRCUITS

To have your order filled promptly and correctly, please furnish the IC301 VHiAN7523++-1 X AN7523++ (20LK32) AK
following informations. IC301 VHiLA4600++-1 X LA4600(20LK62) AM
å IC501 VHiTDA9302H-1 X TDA9302H AK
or
1. MODEL NUMBER 2. REF. NO. VHiAN5522++1
3. PART NO. 4. DESCRIPTION IC601 VHiKA7808AP-1 J KA7808API AE
å IC701 VHiSTRG5653-1 X STRG5653 AQ
IC801 RH-iX3564CEN1 X IX3564CE AX
IC1003 VHiBR24C02F1E J BR24C02F-W AF
★MARK: SPARE PARTS-DELIVERY SECTION
TRANSISTORS
' MARK : X- RAY RELATED PARTS Q201 VS2SC2735//1E J 2SC2735 AC
Q253 VS2SD601A//-1 J 2SD601A AC
Ref. No. Part No. ★ Description Code Q254 VS2SD601A//-1 J 2SD601A AC
Q304 VS2SD601A//-1 J 2SD601A (20LK62) AC
Q320 VS2SD601A//-1 J 2SD601A (20LK62) AC
PICTURE TUBE Q321 VS2SD601A//-1 J 2SD601A (20LK32) AC
Q401 VS2SD601A//-1 J 2SD601A (20LK62) AC
Q601 VS2SC3207//-1 J 2SC3207 AC
å V1 VB48JLL40X/~S X Picture Tube BY Q602 VS2SD2586//1E J 2SD2586 AM
å L703 RCiLG0074PEZZ R Degaussing Coil AQ Q603 VS2SC3198-G-1 J 2SC3198-G AA
å DY601 RCiLH0105GJZZ X Deflection Yoke AX Q751 VS2SC3198-G-1 J 2SC3198-G AA
LHLDW0102GJKZ X Wire Holder, x5 AC Q752 VS2SC3198-G-1 J 2SC3198-G AA
PMAGF3045CEZZ J Purity Magnet AG Q801 VS2SB709A//-1 J 2SB709A AA
QEARC2016PEZZ R Grounding Strap AG Q802 VS2SB709A//-1 J 2SB709A AA
PSPAG0012MEZZ X Wedge, x3 AE
MSPRC0005PEFW J Spring for CRT AB DIODES
D201 RH-EX0676GEZZ J Zener Diode, 33V AA
å D331 RH-DX0302CEZZ J Diode (20LK32) AC
å D331 RH-DX0247CEZZ J Diode (20LK62) AE
D502 RH-EX0615GEZZ J Zener Diode, 5V AA
D503 VHD1SS119//-1 J Diode AB
D505 RH-DX0441CEZZ J Diode AC
D508 RH-DX0131CEZZ J Diode AC
D509 RH-EX0665GEZZ J Zener Diode AA
D511 VHD1SS119//-1 J Diode AB
D531 RH-EX0627GEZZ J Zener Diode, 8.2V AA
D532 RH-EX0627GEZZ J Zener Diode, 8.2V AA
PRINTED WIRING BOARD ASSEMBLIES D601 RH-DX0475CEZZ J Diode AB
(NOT REPLACEMENT ITEM) å D602 VHD1SS244//-1 J Diode AB
å D603 RH-EX0667GEZZ J Zener Diode, 27V AA
PWB-A DUNTKA541WEA2 – MAIN Unit (20LK32) — å D606 RH-DX0131CEZZ J Diode AC
PWB-A DUNTKA541WEA3 – MAIN Unit (20LK62) — å D608 RH-DX0468CEZZ J Diode AE
PWB-B DUNTKA542WEA1 – CRT Unit — or
PWB-E DUNTKA545WEA0 – MTS MODULE Unit — RH-DX0229CEZZ
(20LK62) D651 RH-EX0627GEZZ J Zener Diode, 8.2V AA
D653 VHD1SS119//-1 J Diode AB
D701 RH-DX0476CEZZ J Diode AG
D705 VHD1SS82///1A J Diode AC
D706 VHD1SS82///1A J Diode AC
D707 VHD1SS82///1A J Diode AC
å D751 RH-DX0229CEZZ J Diode AF
å D752 RH-DX0131CEZZ J Diode AC
D754 RH-EX0616GEZZ J Zener Diode, 5.6V AA
D755 RH-EX0603GEZZ J Zener Diode, 3.9V AA
D801 VHD1SS119//-1 J Diode AB
D802 VHD1SS119//-1 J Diode AB
D803 VHD1SS119//-1 J Diode AB
D804 VHD1SS119//-1 J Diode AB
D805 VHD1SS119//-1 J Diode AB
D806 VHD1SS119//-1 J Diode AB
D1001 RH-PX0013PEZZ R LED, ON TIMER AC
D1004 VHD1SS119//-1 J Diode AB

32
 20LK32
20LK62

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

PWB-A: DUNTK541WEA2 (20LK32) å C333 VCEA0A1CW108M J 1000 16V EL. (20LK32) AD

PWB-A: DUNTK541WEA3 (20LK62) å C333 RC-EZ1086CEZZ J 1000 16V EL. (20LK62) AD
MAIN UNIT (Continued) C356 VCKYCY1HB472K J 4700p 50V Ceramic AA
(20LK32)
D1007 RH-EX0263TAZZ J Zener Diode AB C359 VCEA0A1CW106M J 10 16V EL. AB
D1012 RH-EX0611GEZZ J Zener Diode AA C360 VCEA0A1HW225M J 2.2 50V EL. (20LK32) AB
D1018 RH-EX0263TAZZ J Zener Diode AB C409 VCKYCY1EF104Z J 0.1 25V Ceramic AA
D1019 RH-EX0263TAZZ J Zener Diode AB C410 VCKYCY1EF104Z J 0.1 25V Ceramic AA
å VA701 RH-VX0073CEZZ X Varistor AF C411 VCKYCY1HB102K J 1000p 50V Ceramic AA
C501 VCKYPA1HB102K J 1000p 50V Ceramic AA
PACKAGED CIRCUITS C504 VCKYCY1HB103K J 0.01 50V Ceramic AA
PR702 RMPTP0001PEZZ R Packaged Circuit AN C505 VCEA0A1HW107M J 100 50V EL. AB
X1001 RCRSB0300CEZZ J Crystal AF C507 VCKYCY1HB103K J 0.01 50V Ceramic AA
C508 VCFYSA1JB224J X 0.22 63V Mylar AF
FILTERS AND COILS C509 VCEA0A1CW477M J 470 16V EL. AC
CF253 RFiLC0446CEZZ J Ceramic Filter AD C510 VCKYPA2HB102K J 1000p 500V Ceramic AA
L202 VP-DF270K0000 J Peaking 27µH AB C514 VCFYSA1JB473J J 0.047 63V Mylar AC
L203 VP-DF270K0000 J Peaking 27µH AB C531 VCKYCY1HB102K J 1000p 50V Ceramic AA
L204 VP-XF1R2K0000 J Peaking 1.2µH AB C532 VCKYCY1HB102K J 1000p 50V Ceramic AA
L253 VP-XF120K0000 J Peaking 12µH AB C533 VCQYTA1HM104J J 0.1 50V Mylar AA
å L701 RCiLF0096PEZZ R Coil AF C601 VCQYTA1HM563J J 0.056 50V Mylar AB
å L751 RCiLP0225CEZZ J Coil AF C602 VCEA0A1HW475M J 4.7 50V EL. AB
L802 VP-DF100K0000 J Peaking 10µH AB C603 VCEA0A1HW105M J 1.0 50V EL. AB
L803 VP-DF100K0000 J Peaking 10µH AB C604 VCEA0A2EW106M J 10 250V EL. AD
L1030 VP-DF100K0000 J Peaking 10µH AB C605 VCKYPA2HB102K J 1000p 500V Ceramic AA
L1050 VP-DF100K0000 J Peaking 10µH AB C606 VCFPVC2DB474J J 0.47 200V M-Poly. AE
L1051 VP-DF100K0000 J Peaking 10µH AB C607 VCFPVC3ZA772H J 7700p 1.8kV M-Poly. AD
SF201 RFiLC0405CEZZ J S.A.W Filter AH C608 VCKYPA2HB102K J 1000p 500V Ceramic AA
C610 VCEA0A1CW108M J 1000 16V EL. AD
TRANSFORMERS C611 VCEA0A1EW476M J 47 25V EL. AB
å T601 RTRNZ0144PEZZ R Transformer AE C612 VCEA0A1CW477M J 470 16V EL. AC
å T602 RTRNF0229PEZZ X H-Volt Transformer AU C620 VCKYPA2HB102K J 1000p 500V Ceramic AA
or C640 VCFYSB2EB823J J 0.082 250V Mylar AD
RTRNF0231PEZZ C651 VCQYTA1HM222J J 2200p 50V Mylar AA
å T701 RTRNW0015PEZZ X Transformer AK C652 VCQYTA1HM472J J 4700p 50V Mylar AB
C653 VCEA0A1HW105M J 1.0 50V EL. AB
CAPACITORS C654 VCKYCY1HF223Z J 0.022 50V Ceramic AB
[EL. …Electrolytic, M-Poly. …Metalized Polypro Film] C655 VCEA0A1HW106M J 10 50V EL. AB
C201 VCEA0A1CW476M J 47 16V EL. AB C656 VCEA0A1HW224M J 0.22 50V EL. AB
C202 VCEA0A1AW337M+X 330 10V EL. AE C657 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C205 VCKYCY1HF103Z J 0.01 50V Ceramic AA C658 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C206 VCEA0A1HW105M J 1.0 50V EL. AB å C701 RC-FZ036SCEZZ J 0.1 275V Plastic AC
C207 VCKYCY1HB103K J 0.01 50V Ceramic AA C702 RC-KZ0029CEZZ J 0.01 250V Ceramic AC
C208 VCKYCY1HB103K J 0.01 50V Ceramic AA C703 RC-KZ0029CEZZ J 0.01 250V Ceramic AC
C209 VCKYCY1HB103K J 0.01 50V Ceramic AA C704 RC-KZ0029CEZZ J 0.01 250V Ceramic AC
C210 VCKYCY1HF103Z J 0.01 50V Ceramic AA C705 RC-EZ0804CEZZ J 220 400V EL. AU
C211 VCKYCY1HF103Z J 0.01 50V Ceramic AA C709 RC-KZ0039CEZZ J 680 2kV Ceramic AB
C231 VCKYCY1HF223Z J 0.022 50V Ceramic AB C710 VCEA0A1HW476M J 47 50V EL. AB
C232 VCKYCY1HB821K J 820p 50V Ceramic AA C711 VCKYPA1HB102K J 1000p 50V Ceramic AA
C233 VCKYCY1HB472K J 4700p 50V Ceramic AA C712 VCKYPA1HB471K J 470p 50V Ceramic AA
C234 VCKYCY1EF104Z J 0.1 25V Ceramic AA å C751 RC-KZ0092GEZZ J 3300p AC250V Ceramic AC
C251 VCKYCY1HF223Z J 0.022 50V Ceramic AB å C752 VCKYPH3DB561K J 560p 2kV Ceramic AC
C252 VCEA0A1CW107M J 100 16V EL. AC å C753 RC-EZ0724CEZZ J 100 160V EL. AG
C301 VCEA0A1CW477M J 470 16V EL. (20LK32) AC å C754 RC-EZ0638CEZZ J 33 160V EL. AG
C301 RC-EZA009WJZZ+ X 220 16V EL. (20LK62) AF å C755 VCEA0A1CW108M J 1000 16V EL. AD
C302 VCEA0A1CW477M J 470 16V EL. (20LK62) AC å C756 VCQYTA1HM103J J 0.01 50V Mylar AA
C303 VCEA0A1CW477M J 470 16V EL. (20LK62) AC C759 VCEA0A0JW477M J 470 6.3V EL. AC
C304 VCEA0A1CW106M J 10 16V EL. AB C760 VCEA0A0JW228M J 2200 6.3V EL. AD
C305 VCEA0A1HW475M J 4.7 50V EL. (20LK62) AB C801 VCEA0A1HW105M J 1.0 50V EL. AB
C306 VCEA0A1HW105M J 1.0 50V EL. (20LK62) AB C802 VCEA0A1CW337M J 330 16V EL. AC
C307 VCEA0A1HW105M J 1.0 50V EL. (20LK32) AB C803 VCEA0A1CW107M J 100 16V EL. AC
C307 VCEA0A1HW224M J 0.22 50V EL. (20LK62) AB C804 VCKYCY1HB222K J 2200p 50V Ceramic AA
C308 VCKYCY1CB473K J 0.047 16V Ceramic AA C805 VCKYD41HB102K J 1000p 50V Ceramic AA
(20LK62) C806 VCKYD41HB102K J 1000p 50V Ceramic AA
C310 VCEA0A1HW225M J 2.2 50V EL. (20LK32) AB C807 VCKYD41HB102K J 1000p 50V Ceramic AA
C311 VCEA0A1HW105M J 1.0 50V EL. (20LK32) AB C808 VCEA0A1CW107M J 100 16V EL. AC
C311 RC-EZA008WJZZ+ X 100 16V EL. (20LK62) AE C809 VCKYCY1CF474Z J 0.47 16V Ceramic AB
C312 VCEA0A1HW225M J 2.2 50V EL. (20LK32) AB C810 VCKYCY1CF474Z J 0.47 16V Ceramic AB
C312 VCEA0A1HW224M J 0.22 50V EL. (20LK62) AB C811 VCEA0A1CW107M J 100 16V EL. AC
C313 VCKYCY1CB473K J 0.047 16V Ceramic AA C812 VCFYFA1HA224J J 0.22 50V Mylar AB
(20LK62) C813 VCFYFA1HA224J J 0.22 50V Mylar AB
C313 VCKYCY1HB332K J 3300p 50V Ceramic AA C814 VCKYCY1HB471K J 470p 50V Ceramic AA
(20LK32) C816 VCKYCY1HB471K J 470p 50V Ceramic AA
C314 VCEAKA1HW224M J 0.22 50V EL. (20LK62) AB C1001 VCEA0A0JW107M J 100 6.3V EL. AB
å C332 VCQYTA1HM103J J 0.01 50V Mylar AA C1002 VCEA0A0JW107M J 100 6.3V EL. AB

33
20LK32
20LK62

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

PWB-A: DUNTK541WEA2 (20LK32) R219 VRD-RA2BE392J J 3.9k 1/8W Carbon AA

PWB-A: DUNTK541WEA3 (20LK62) R220 VRS-CY1JF221J J 220 1/16W M-Ox. AA
MAIN UNIT (Continued) R230 VRS-CY1JF473J J 47k 1/16W M-Ox. AA
R231 VRD-RA2BE681J J 680 1/8W Carbon AA
C1003 VCEA0A1CW106M J 10 16V EL. AB R232 VRS-CY1JF272J J 2.7k 1/16W M-Ox. AA
C1004 VCKYCY1CF474Z J 0.47 16V Ceramic AB R233 VRS-CY1JF101J J 100 1/16W M-Ox. AA
C1005 VCKYCY1CF474Z J 0.47 16V Ceramic AB R234 VRS-CY1JF391J J 390 1/16W M-Ox. AA
C1006 VCEA0A1CW106M J 10 16V EL. AB R257 VRS-CY1JF181J J 180 1/16W M-Ox. AA
C1008 VCCCCY1HH330J J 33p 50V Ceramic AA R258 VRS-CY1JF181J J 180 1/16W M-Ox. AA
C1009 VCCCCY1HH330J J 33p 50V Ceramic AA R259 VRS-CY1JF471J J 470 1/16W M-Ox. AA
C1010 VCEA0A0JW107M J 100 6.3V EL. AB R260 VRS-CY1JF392J J 3.9k 1/16W M-Ox. AA
C1011 VCKYCY1CF474Z J 0.47 16V Ceramic AB R261 VRS-CY1JF223J J 22k 1/16W M-Ox. AA
C1012 VCKYCY1CF474Z J 0.47 16V Ceramic AB R262 VRS-CY1JF560J J 56 1/16W M-Ox. AA
C1013 VCEA0A0JW107M J 100 6.3V EL. AB R263 VRS-CY1JF560J J 56 1/16W M-Ox. AA
C1016 VCQYTA1HM104J J 0.1 50V Mylar AA R301 VRS-CY1JF101J J 100 1/16W M-Ox. AA
C1018 VCKYCY1HB221K J 220p 50V Ceramic AA (20LK32)
C1024 VCQYTA1HM104J J 0.1 50V Mylar AA R304 VRS-CY1JF221J J 220 1/16W M-Ox. AA
C1026 VCEA0A0JW107M J 100 6.3V EL. AB (20LK62)
R304 VRS-CY1JF683J J 68k 1/16W M-Ox. AA
RESISTORS (20LK32)
[M-Ox. …Metal Oxide, M-Film …Metal Film] R305 VRS-CY1JF274J J 270k 1/16W M-Ox. AA
RJ1 VRS-CY1JF000J J 0 1/16W M-Ox. AA R306 VRD-RA2BE391J J 390 1/8W Carbon AA
(20LK62) (20LK62)
RJ2 VRS-CY1JF000J J 0 1/16W M-Ox. AA R307 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ4 VRS-CY1JF000J J 0 1/16W M-Ox. AA (20LK32)
RJ5 VRS-CY1JF000J J 0 1/16W M-Ox. AA R307 VRS-CY1JF122J J 1.2k 1/16W M-Ox. AA
(20LK62) (20LK62)
RJ8 VRS-CY1JF000J J 0 1/16W M-Ox. AA R308 VRD-RA2BE103J J 10k 1/8W Carbon AA
RJ9 VRS-CY1JF000J J 0 1/16W M-Ox. AA (20LK62)
RJ10 VRS-CY1JF000J J 0 1/16W M-Ox. AA R309 VRD-RA2BE473J J 47k 1/8W Carbon AA
RJ13 VRS-CY1JF000J J 0 1/16W M-Ox. AA (20LK62)
RJ14 VRS-CY1JF000J J 0 1/16W M-Ox. AA R310 VRS-CY1JF473J J 47k 1/16W M-Ox. AA
RJ15 VRS-CY1JF000J J 0 1/16W M-Ox. AA (20LK32)
RJ16 VRS-CY1JF000J J 0 1/16W M-Ox. AA R311 VRS-CY1JF473J J 47k 1/16W M-Ox. AA
RJ17 VRS-CY1JF000J J 0 1/16W M-Ox. AA R313 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA
RJ19 VRS-CY1JF000J J 0 1/16W M-Ox. AA (20LK32)
RJ21 VRS-CY1JF000J J 0 1/16W M-Ox. AA R314 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
RJ23 VRS-CY1JF000J J 0 1/16W M-Ox. AA R315 VRS-CY1JF122J J 1.2k 1/16W M-Ox. AA
(20LK62) (20LK62)
RJ24 VRS-CY1JF000J J 0 1/16W M-Ox. AA R315 VRS-CY1JF822J J 8.2k 1/16W M-Ox. AA
RJ26 VRS-CY1JF000J J 0 1/16W M-Ox. AA (20LK32)
RJ28 VRS-CY1JF000J J 0 1/16W M-Ox. AA R316 VRS-CY1JF104J J 100k 1/16W M-Ox. AA
RJ32 VRS-CY1JF000J J 0 1/16W M-Ox. AA (20LK62)
RJ33 VRS-CY1JF000J J 0 1/16W M-Ox. AA R322 VRS-CY1JF272J J 2.7k 1/16W M-Ox. AA
(20LK32) (20LK32)
RJ34 VRS-CY1JF000J J 0 1/16W M-Ox. AA R323 VRD-RA2BE274J J 270k 1/8W Carbon AA
(20LK62) (20LK32)
RJ35 VRS-CY1JF000J J 0 1/16W M-Ox. AA R333 VRS-CY1JF101J J 100 1/16W M-Ox. AA
(20LK32) (20LK32)
RJ37 VRS-CY1JF000J J 0 1/16W M-Ox. AA R334 VRS-CY1JF332J J 3.3k 1/16W M-Ox. AA
RJ38 VRS-CY1JF000J J 0 1/16W M-Ox. AA R335 VRS-CY1JF564J J 560k 1/16W M-Ox. AA
RJ41 VRS-CY1JF000J J 0 1/16W M-Ox. AA R336 VRD-RA2BE332J J 3.3k 1/8W Carbon AA
RJ42 VRS-CY1JF000J J 0 1/16W M-Ox. AA (20LK62)
RJ43 VRS-CY1JF000J J 0 1/16W M-Ox. AA R337 VRS-CY1JF564J J 560k 1/16W M-Ox. AA
RJ46 VRS-CY1JF000J J 0 1/16W M-Ox. AA (20LK62)
RJ49 VRS-CY1JF000J J 0 1/16W M-Ox. AA R340 VRS-CY1JF101J J 100 1/16W M-Ox. AA
RJ50 VRS-CY1JF000J J 0 1/16W M-Ox. AA (20LK62)
RJ51 VRS-CY1JF000J J 0 1/16W M-Ox. AA R341 VRS-CY1JF822J J 8.2k 1/16W M-Ox. AA
RJ52 VRS-CY1JF000J J 0 1/16W M-Ox. AA (20LK62)
RJ53 VRS-CY1JF000J J 0 1/16W M-Ox. AA R362 VRS-CY1JF332J J 3.3k 1/16W M-Ox. AA
RJ55 VRS-CY1JF000J J 0 1/16W M-Ox. AA (20LK62)
RJ70 VRS-CY1JF000J J 0 1/16W M-Ox. AA R363 VRS-CY1JF564J J 560k 1/16W M-Ox. AA
RJ71 VRS-CY1JF000J J 0 1/16W M-Ox. AA (20LK62)
RJ73 VRS-CY1JF000J J 0 1/16W M-Ox. AA R364 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ75 VRS-CY1JF000J J 0 1/16W M-Ox. AA (20LK32)
RJ76 VRS-CY1JF000J J 0 1/16W M-Ox. AA R364 VRS-CY1JF332J J 3.3k 1/16W M-Ox. AA
RJ77 VRS-CY1JF000J J 0 1/16W M-Ox. AA (20LK62)
R201 VRS-CY1JF101J J 100 1/16W M-Ox. AA R365 VRS-CY1JF564J J 560k 1/16W M-Ox. AA
R202 VRS-CY1JF101J J 100 1/16W M-Ox. AA (20LK62)
R205 VRS-CY1JF680J J 68 1/16W M-Ox. AA R401 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R206 VRS-CY1JF122J J 1.2k 1/16W M-Ox. AA (20LK62)
R207 VRS-CY1JF221J J 220 1/16W M-Ox. AA R430 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R208 VRS-CY1JF122J J 1.2k 1/16W M-Ox. AA (20LK62)
R209 VRS-CY1JF392J J 3.9k 1/16W M-Ox. AA R431 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R216 VRS-RG3LB223J+ X 22k 3W M-Ox. AF (20LK32)

34
 20LK32
20LK62

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

PWB-A: DUNTK541WEA2 (20LK32) R808 VRS-CY1JF221J J 220 1/16W M-Ox. AA

PWB-A: DUNTK541WEA3 (20LK62) R809 VRD-RA2BE224J J 220k 1/8W Carbon AA
MAIN UNIT (Continued) R812 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R813 VRS-CY1JF221J J 220 1/16W M-Ox. AA
R432 VRS-CY1JF750J J 75 1/16W M-Ox. AA R1002 VRS-CY1JF822J J 8.2k 1/16W M-Ox. AA
R433 VRS-CY1JF103J J 10k 1/16W M-Ox. AA R1003 VRS-CY1JF562J J 5.6k 1/16W M-Ox. AA
(20LK62) R1006 VRS-CY1JF562J J 5.6k 1/16W M-Ox. AA
R464 VRS-CY1JF750J J 75 1/16W M-Ox. AA R1007 VRS-CY1JF562J J 5.6k 1/16W M-Ox. AA
(20LK62) R1008 VRS-CY1JF822J J 8.2k 1/16W M-Ox. AA
R501 VRD-RA2BE222J J 2.2k 1/8W Carbon AA R1009 VRS-CY1JF562J J 5.6k 1/16W M-Ox. AA
R502 VRD-RM2HD102J J 1.0k 1/2W Carbon AA R1011 VRS-CY1JF332J J 3.3k 1/16W M-Ox. AA
R503 VRN-RL3DB2R2J+ X 2.2 2W M-Film AE R1012 VRD-RA2BE391J J 390 1/8W Carbon AA
R504 VRS-CY1JF181J J 180 1/16W M-Ox. AA R1013 VRD-RA2BE101J J 100 1/8W Carbon AB
R505 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA R1014 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R506 VRS-RG3AB391J X 390 1W M-Ox. AE R1015 VRS-CY1JF332J J 3.3k 1/16W M-Ox. AA
R507 VRN-RL3AB1R0J X 1.0 1W M-Film AE R1016 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R510 VRD-RA2BE333J J 33k 1/8W Carbon AA R1017 VRS-CY1JF332J J 3.3k 1/16W M-Ox. AA
R511 VRS-CY1JF181J J 180 1/16W M-Ox. AA R1019 VRS-CY1JF000J J 0 1/16W M-Ox. AA
R512 VRD-RM2HD100J J 10 1/2W Carbon AA R1020 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R531 VRS-CY1JF101J J 100 1/16W M-Ox. AA R1021 VRS-CY1JF183J J 18k 1/16W M-Ox. AA
R532 VRS-CY1JF101J J 100 1/16W M-Ox. AA R1022 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R533 VRD-RA2BE393J J 39k 1/8W Carbon AA R1023 VRS-CY1JF221J J 220 1/16W M-Ox. AA
R601 VRS-RG2HC102J J 1.0k 1/2W M-Ox. AA R1024 VRS-CY1JF183J J 18k 1/16W M-Ox. AA
R602 VRD-RA2BE393J J 39k 1/8W Carbon AA R1025 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R603 VRD-RA2BE223J J 22k 1/8W Carbon AA R1026 VRS-CY1JF224J J 220k 1/16W M-Ox. AA
R604 VRD-RA2BE393J J 39k 1/8W Carbon AA R1028 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R605 VRD-RM2HD823J J 82k 1/2W Carbon AA R1032 VRS-CY1JF332J J 3.3k 1/16W M-Ox. AA
å R606 VRN-RL3AB2R2J X 2.2 1W M-Film AE R1034 VRS-CY1JF101J J 100 1/16W M-Ox. AA
å R607 VRD-RM2HD270J J 27 1/2W Carbon AA R1035 VRS-CY1JF332J J 3.3k 1/16W M-Ox. AA
å R609 VRD-RA2BE154J J 150k 1/8W Carbon AA R1036 VRS-CY1JF332J J 3.3k 1/16W M-Ox. AA
å R610 VRD-RA2BE102G J 1.0k 1/8W Carbon AB R1037 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R611 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA R1038 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R612 VRS-CY1JF123J J 12k 1/16W M-Ox. AA R1039 VRS-CY1JF223J J 22k 1/16W M-Ox. AA
R613 VRS-CY1JF103J J 10k 1/16W M-Ox. AA R1040 VRS-CY1JF101J J 100 1/16W M-Ox. AA
å R614 VRD-RM2HD100J J 10 1/2W Carbon AA R1041 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R615 VRS-RG3DB682J+ X 6.8k 2W M-Ox. AE R1042 VRD-RA2BE471J J 470 1/8W Carbon AA
R616 VRN-RL3ABR47J+ X 0.47 1W M-Film AE R1046 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R618 VRS-RG3DB391J+ X 390 2W M-Ox. AE R1047 VRS-CY1JF332J J 3.3k 1/16W M-Ox. AA
R619 VRS-RG3LB562J X 5.6k 3W M-Ox. AF R1050 VRS-CY1JF392J J 3.9k 1/16W M-Ox. AA
R620 VRS-RG3AB472J+ X 4.7k 1W M-Ox. AE R1051 VRS-CY1JF683J J 68k 1/16W M-Ox. AA
R622 VRD-RA2BE102J J 1.0k 1/8W Carbon AA R1066 VRS-CY1JF472J J 4.7k 1/16W M-Ox. AA
R625 VRN-VV3DB4R7J J 4.7 2W M-Film AB R1072 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R626 VRD-RM2HD470J J 47 1/2W Carbon AA R1073 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R641 VRN-RL2HCR47J+ X 0.47 1/2W M-Film AE JA223 VRD-RA2BE222J J 2.2k 1/8W Carbon AA
R651 VRS-CY1JF223J J 22k 1/16W M-Ox. AA (20LK62)
R652 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA JA721 VRD-RA2BE102J J 1.0k 1/8W Carbon AA
R653 VRS-CY1JF822J J 8.2k 1/16W M-Ox. AA (20LK32)
R654 VRS-CY1JF273J J 27k 1/16W M-Ox. AA
R655 VRS-CY1JF391J J 390 1/16W M-Ox. AA SWITCHES
R656 VRS-CY1JF100J J 10 1/16W M-Ox. AA S1001 QSW-K0003AJZZ J CH-UP AB
R658 VRD-RA2BE101J J 100 1/8W Carbon AB S1002 QSW-K0003AJZZ J CH-DOWN AB
R663 VRD-RA2BE101J J 100 1/8W Carbon AB S1003 QSW-K0003AJZZ J VOL-UP AB
R701 VRW-KQ3NC3R9K J 3.9 7W Cement AE S1004 QSW-K0003AJZZ J VOL-DOWN AB
R704 VRN-SV2HC1R0J J 1.0 1/2W M-Film AA S1005 QSW-K0003AJZZ J PICTURE/PRESET AB
R707 VRS-VV3DB104J J 100k 2W M-Ox. AB S1006 QSW-K0114CEZZ J POWER AE
R708 VRD-RA2BE681J J 680 1/8W Carbon AA
R709 VRN-RL3DBR47J+ X 0.47 2W M-Film AE MISCELLANEOUS PARTS
R710 VRN-RL3DBR39J X 0.39 2W M-Film AE å F701 QFS-C3229CEZZ J Fuse, T3.14AL AD
R711 VRD-RA2BE682J J 6.8k 1/8W Carbon AA FB601 RBLN-0091GEZZ J Ferrite Bead AB
R712 VRD-RA2BE152J J 1.5k 1/8W Carbon AA FH701 QFSHD1013CEZZ J Fuse Holder AC
R716 VRD-RA2BE562J J 5.6k 1/8W Carbon AA FH702 QFSHD1014CEZZ J Fuse Holder AC
å R751 RR-DZ0049CEZZ J 3.9M 1/2W Solid AB J402 QJAKE0210CE04 X Jack, Video (AV-In2) AF
å R752 RR-DZ0049CEZZ J 3.9M 1/2W Solid AB (20LK32)
å R753 VRD-RM2HD124J J 120k 1/2W Carbon AA J402 QJAKE0211CE04 X Jack, Video (AV-In2) AF
R754 VRD-RM2HD150J J 15 1/2W Carbon AA (20LK62)
R755 VRD-RA2BE221J J 220 1/8W Carbon AA J403 QJAKE0210CE09 X Jack, Audio (L)(AV-In2) AF
R756 VRD-RM2HD270J J 27 1/2W Carbon AA (20LK32)
R757 VRS-CY1JF151J J 150 1/16W M-Ox. AA J403 QJAKE0211CE09 X Jack, Audio (L)(AV-In2) AF
R801 VRS-CY1JF221J J 220 1/16W M-Ox. AA (20LK62)
R802 VRS-CY1JF221J J 220 1/16W M-Ox. AA J404 QJAKE0210CE02 X Jack, Audio (R)(AV-In2) AF
R803 VRS-CY1JF221J J 220 1/16W M-Ox. AA (20LK62)
R804 VRS-CY1JF221J J 220 1/16W M-Ox. AA J409 QJAKF0074CEZZ X Jack, Rear AV-In (20LK32) AG
R805 VRS-CY1JF822J J 8.2k 1/16W M-Ox. AA J409 QJAKG0093CEZZ X Jack, Rear AV-In (20LK62) AK
R806 VRS-CY1JF123J J 12k 1/16W M-Ox. AA P302 QPLGN0461CEZZ J Plug, 4-pin (S) AB
R807 VRS-CY1JF103J J 10k 1/16W M-Ox. AA P601 QPLGN0660CEZZ J Plug, 6-pin (K) AC

35
20LK32
20LK62

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

PWB-A: DUNTK541WEA2 (20LK32) PWB-B: DUNTK542WEA1

PWB-A: DUNTK541WEA3 (20LK62)
MAIN UNIT (Continued) CRT UNIT
P603 QPLGN0361CEZZ J Plug, 3-pin (TP651-3) AB TRANSISTORS
P701 QPLGN0260CEZZ J Plug, 2-pin (M) AC Q870 RH-TX0110BMZZ+ X TX0110BM AE
P702 QPLGN0269GEZZ J Plug, 2-pin AB Q871 RH-TX0110BMZZ+ X TX0110BM AE
P1002 QPLGN0561CEZZ J Plug, 5-pin (BC) AB Q872 RH-TX0110BMZZ+ X TX0110BM AE
RMC1001 RRMCU0222CEZZ J R/C Receiver AL Q883 RH-TX0124BMZZ+ X TX0110BM AE
RDA301 PRDAR0119GJFW X Heat Sink, for IC301 AD Q885 RH-TX0124BMZZ+ X TX0124BM AE
(20LK32) Q887 RH-TX0124BMZZ+ X TX0124BM AE
RDA301 PRDAR0120GJFW X Heat Sink, for IC301 AD
(20LK62) DIODES
RDA501 PRDAR0118GJFW X Heat Sink, for IC501 AE D881 VHD1SS119//-1 J Diode AB
RDA602 PRDAR0224PEFW R Heat Sink, for Q602 AF D882 VHD1SS119//-1 J Diode AB
RDA701 PRDAR0298PEFW R Heat Sink, for IC701 AF D883 VHD1SS119//-1 J Diode AB
TP201 QLUGP0102PEZZ R Lug, Test Point AA D884 VHD1SS119//-1 J Diode AB
LHLDP1066PE00 R Holder AC D885 VHD1SS119//-1 J Diode AB
LHLDW1104PEZZ X Holder AE
LHLDW1105PEZZ X Holder AE CAPACITORS
LX-BZ0086TAFD J Screw AA [EL. …Electrolytic]
LX-BZ3049GEFD J Screw AA C871 VCCSCY1HL471J J 470p 50V Ceramic AA
LX-TZ3004CEFD J Screw AA C872 VCCSCY1HL471J J 470p 50V Ceramic AA
QCNW-2619PEZZ X Connecting Cord AD C873 VCCSCY1HL471J J 470p 50V Ceramic AA
QCNW-2620PEZZ X Connecting Cord AD C875 VCKYPA2HB102K J 1000p 500V Ceramic AA
C876 RC-KZ0150CEZZ J 1000p 3kV Ceramic AB
C878 VCEA0A2EW106M J 10 250V EL. AD
C880 VCCSCY1HL471J J 470p 50V Ceramic AA
C881 VCKYPA1HB471K J 470p 50V Ceramic AA
C882 VCKYPA1HB471K J 470p 50V Ceramic AA
C886 VCKYPA2HB102K J 1000p 500V Ceramic AA

RESISTORS
[M-Ox. …Metal Oxide]
R879 VRS-CY1JF471J J 470 1/16W M-Ox. AA
R880 VRS-CY1JF471J J 470 1/16W M-Ox. AA
R881 VRS-CY1JF471J J 470 1/16W M-Ox. AA
R882 VRS-VV3DB153J J 15k 2W M-Ox. AA
R883 VRD-RM2HD272J J 2.7k 1/2W Carbon AA
R884 VRS-VV3DB153J J 15k 2W M-Ox. AA
R885 VRD-RM2HD272J J 2.7k 1/2W Carbon AA
R886 VRS-VV3DB153J J 15k 2W M-Ox. AA
R887 VRD-RM2HD272J J 2.7k 1/2W Carbon AA
R888 VRS-CY1JF471J J 470 1/16W M-Ox. AA
R892 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA
R893 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA
R894 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA
R898 VRS-CY1JF471J J 470 1/16W M-Ox. AA
R899 VRS-CY1JF471J J 470 1/16W M-Ox. AA

MISCELLANEOUS PARTS
å SC881 QSOCV0840CEZZ J CRT Socket AK
or
QSOCV0841CEZZ

36
 20LK32
20LK62

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

PWB-E: DUNTK545WEA0 (20LK62)

MTS MODULE UNIT
INTEGRATED CIRCUITS
IC3001 VHiCXA2074Q-1 J CXA2074Q AY
IC3002 VHiMM1501XN-1 X MM1501XNRE AH

TRANSISTORS
Q3003 VS2SC3198-G-1 J C3198-G AA

DIODE
D3001 RH-EX0632GEZZ J Zener Diode, 9.9V AA

CAPACITORS
[EL. …Electrolytic]
C3001 VCE9GA1HW475M J 4.7 50V EL. (N.P) AB
C3002 VCKYCY1HB562K J 5600p 50V Ceramic AA
C3003 VCQYTA1HM123K J 0.012 50V Mylar AA
C3004 VCEA0A1HW105M J 1.0 50V EL. AB
C3005 VCEA9A1HW475M J 4.7 50V EL. AB
C3006 VCEA0A1CW106M J 10 16V EL. AB
C3007 VCEA0A1HW475M J 4.7 50V EL. AB
C3008 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C3009 VCEA0A1CW227M J 220 16V EL. AC
C3010 VCE9GA1HW475M J 4.7 50V EL. (N.P) AB
C3011 VCEA0A1HW475M J 4.7 50V EL. AB
C3012 VCE9GA1HW475M J 4.7 50V EL. (N.P) AB
C3013 VCKYCY1HB272K J 2700p 50V Ceramic AA
C3014 VCQYTA1HM473K J 0.047 50V Mylar AB
C3015 VCEACA1HC335K X 3.3 50V EL. AF
C3016 VCE9GA1HW475M J 4.7 50V EL. (N.P) AB
C3017 VCEACA1CC106K J 10 16V EL. AC
C3018 VCEA0A1HW105M J 1.0 50V EL. AB
C3019 VCEA0A1CW106M J 10 16V EL. AB
C3020 VCEA0A1CW106M J 10 16V EL. AB
C3021 VCEA0A1CW106M J 10 16V EL. AB
C3022 VCEA0A1CW106M J 10 16V EL. AB
C3031 VCEA0A1CW106M J 10 16V EL. AB
C3032 VCEA0A1CW106M J 10 16V EL. AB
C3033 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C3034 VCEA0A1HW224M J 0.22 50V EL. AB
C3039 VCEA0A1CW227M J 220 16V EL. AC

RESISTORS
[M-Ox. …Metal Oxide]
R3001 VRD-RA2BE221J J 220 1/8W Carbon AA
R3002 VRD-RA2BE221J J 220 1/8W Carbon AA
R3003 VRS-CY1JF105J J 1.0M 1/16W M-Ox. AA
R3004 VRS-CY1JF104J J 100k 1/16W M-Ox. AA
R3005 VRS-CY1JF623J J 62k 1/16W M-Ox. AA
R3007 VRS-CY1JF332J J 3.3k 1/16W M-Ox. AA
R3008 VRS-CY1JF302J J 3.0k 1/16W M-Ox. AA
R3010 VRS-CY1JF392J J 3.9k 1/16W M-Ox. AA
R3011 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA
R3012 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA
R3013 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA
R3014 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA
R3015 VRD-RA2BE101J J 100 1/8W Carbon AB
R3022 VRD-RA2BE560J J 56 1/8W Carbon AA
R3023 VRD-RM2HD5R6J J 5.6 1/2W Carbon AA
R3025 VRS-CY1JF472J J 4.7k 1/16W M-Ox. AA

MISCELLANEOUS PARTS
P3001 QPLGZ0810CEZZ J Plug, 8-pin (M) AD
P3002 QPLGZ0810CEZZ J Plug, 8-pin (SW) AD
P3003 QPLGZ0810CEZZ J Plug, 8-pin (N) AD

37
20LK32
20LK62

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

MISCELLANEOUS PARTS PACKING PARTS

(NOT REPLACEMANT ITEM)
å ACC701 QACCZ3008PEZZ R AC Cord AN SPAKC0208GJZZ – Packing Case —
SP301 VSP9050PB40YA X Speaker (R)(20LK32) AK SPAKP0102GJZZ – Wrapping Paper —
SP302 VSP9050PB40YA X Speaker (L)(20LK32) AK SPAKX0124GJZZ – Buffer Material —
SP301 VSP9050PB394A X Speaker (R)(20LK62) AK SSAKA0101GJZZ – Polyethylene Bag —
SP302 VSP9050PB394A X Speaker (L)(20LK62) AK
LHLDK0012PEZZ R AC Cord Holder AC
LHLDW1003PEZZ R Holder AA
LHLDW1009PEZZ R Holder AA
LHLDW1033PEZZ R Holder AA
LHLDW1060CEZZ R Holder AB
LHLDW1104PEZZ X Holder AE
LHLDW1105PEZZ X Holder AE
LHLDZ0063PEZZ R Holder AD
LX-TZ0104GJFD X CRT Screw, x4 AF
LX-WZ0102GJFD X CRT Washer, x4 AE
LHLDW1070PEKZ J Holder AD
LHLDZ1002GJZZ
LHLDZ1003GJZZ
X
X
Holder
Holder
AE
AF
CABINET PARTS
LX-TZ3004CEFD J Screw AA
PSPAH0117GJ00 X Spacer AD 20LK32
PSPAH0118GJ00 X Spacer AD 1 CCABA0139WEH0 X
Front Cabinet Ass’y BB
QCNW-2562PEZZ J Connecting Cord AF 1-1 Not Available –
Front Cabinet —
TCAUH0102GJZZ X AV Notice Label (20LK32) AE 1-4 GCOVA0110GJSA X
Cover for LED, R/C AG
TCAUS3000GJZZ X Caution Card AB 1-2 HBDGB1001GJSA X
Badge, "SHARP" AE
TLABM0005GJZZ X Model Label AF 1-3 JBTN-0114GJSA X
Button, Menu, CH-up/down, AG
TLABZ0166GJZZ X Case Label (20LK32) AE Vol-up/down
TLABZ0167GJZZ X Case Label (20LK62) AE 1-5 JBTN-0113GJSA X Button, Power AG
XTASD40P20000 J Screw AA 1-6 MSPRC0005PEFW J Spring for Power Button AB

2 GCABB0128GJKA X Rear Cabinet AY

20LK62
1 CCABA0140WEH0 X
Front Cabinet Ass’y BB
1-1 Not Available –
Front Cabinet —
1-4 GCOVA0110GJSA X
Cover for LED, R/C AG
1-2 HBDGB1001GJSA X
Badge, "SHARP" AE
SUPPLIED ACCESORRIES 1-3 JBTN-0114GJSA X
Button, Menu, CH-up/down, AG
Vol-up/down
1-5 JBTN-0113GJSA X Button, Power AG
QPLGA0017CEZZ J AC Plug Adapter AK 1-6 MSPRC0005PEFW J Spring for Power Button AB
RRMCG1339CESB X Infrared R/C Unit AP
TiNS-7437GJZZ X Operation Manual AP 2 GCABB0129GJKA X Rear Cabinet AY

1 1-1

1-2

1-6 1-5 1-4 1-3

38
 20LK32
20LK62

PACKING OF THE SET

★ Polyethylene Bag

Operation Manual
Infrared R/C Unit
★ Batteries
★ Wrapping Paper

★ Buffer Material

FRONT ★ Packing Case

Use tape to fix

top side of pack
case.

REAR

Use 12 staples fix

the packing case.

★ MARK : Not Replacement Items.

39
20LK32
20LK62

COPYRIGHT © 2001 BY SHARP CORPORATION

ALL RIGHTS RESERVED.

No part of this publication may be reproduced,

stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.

SHARP CORPORATION
D SEM P SEMEX TQ1225-S AV Systems Group
Oct. 2001 Printed in Japan Quality & Reliability Control Center
MI. KG Yaita, Tochigi 329-2193, Japan
40