Product Data Sheet

Edition 20/11/2012
Identification no:
01 07 01 01 002 0 000001
SikaTop Seal-107















1 1/5
C
o
n
s
t
r
u
c
t
i
o
n

SikaTop Seal-107
SikaTop

Seal-107
Waterproofing/damp-proofing cementitious slurry
Product
Description
SikaTop

Seal-107 is a two part polymer modified cementitious waterproof mortar

slurry comprising of a liquid polymer and a cement based mix incorporating special
admixtures.
Uses SikaTop

Seal-107 is used for:
Interior and exterior waterproofing and damp-proofing of concrete, cementitious
rendering, brickwork and blockwork
Protection of concrete structures against the effects of de-icing salts and
freeze-thaw attack
Rigid waterproofing of basement walls in new construction and refurbishment
Pore / blowhole filling
Waterproofing of drinking water reservoirs subject to positive water pressure
Sealing fine hairline cracks in concrete structures (not subject to movement)
Levelling mortar for concrete repair works
Characteristics /
Advantages
Easy to apply by brush or in thin trowel applications
No water required
Prebatched components
Hand or spray applied
Easy and fast mixing
Very good adhesion
Protects concrete against carbonation
Protects against water penetration
Non-corrosive to steel or iron
Overpaintable
Approved for potable water contact
Tests
Product Data
Form
Appearance /Colours Part A: white liquid
Part B: grey or white powder
Mixed product: cement grey or off-white
Packaging 25 kg units (20 kg bag and 5 kg pail)

2 2/5
SikaTop Seal-107
Storage
Storage Conditions/
Shelf-Life
6 months from date of production if stored properly in undamaged and unopened
original sealed packaging in dry and cool conditions. Liquid component must be
protected from frost.
Technical Data
Chemical Base Part A: liquid polymer and additive
Part B: portland cement selected aggregate and admixtures
Density Fresh mortar density: ~ 2.00 kg/l
Layer Thickness 0.75 mm min.
4.0 mm max.
Thermal Expansion 13 x 10
-6
per C
Carbon Dioxyde
Diffusion Coefficient
(CO2)
CO2 ~ 35.000
Water Vapour Diffusion
Coefficient (H2O)
H2O ~ 500
Mechanical / Physical
Properties
Compressive Strength (According to EN 196-1)
3 days ~ 20 N/mm
2

28 days ~ 35 N/mm
2


Flexural Strength (According to EN 196-1)
3 days ~ 6 N/mm
2

28 days ~ 10 N/mm
2


Tensile Strength Cured in water: ~ 3.2 N/mm
2
after 14 days exposure (According to DIN 53455)
Cured in air: ~ 4.5 N/mm
2
after 14 days exposure
Bond Strength 2.0 to 3.0 N/mm
2
(failure in substrate)
E-Modulus Static: ~ 8.4 kN/mm
2

System
Information
Application Details
Consumption / Dosage Dependent on the substrate roughness, surface profile and thickness of the layer
applied.
As a guide, ~ 2.0 kg/m
2
/mm (excluding allowances for loss wastage, surface profile
and porosity, etc.).
1 unit of 25 kg yields ~ 12.5 l of mortar.
Substrate Quality The substrate must be structurally sound and free of all traces of contaminants,
loose and friable particles, cement laitance, oils and grease etc.
The concrete pull off (tensile adhesive) strength must be > 1.0 N/mm
2
.

3 3/5
SikaTop Seal-107
Substrate Preparation General:
The substrate must be prepared by suitable mechanical preparation techniques
such as high pressure water jetting, needle guns, blastcleaning, scabblers etc. and
properly pre-wetted to a saturated surface dry condition.
For pore / blowhole filling:
Blastclean to remove all contaminants including from within the pores / blowholes.
As a levelling mortar:
Prepare and clean all surfaces by suitable mechanical means such as abrasive
blast cleaning or equivalent to ensure cement laitance, surface contamination and
all existing coatings are removed and all blowholes and honeycombed areas are
exposed. The resultant surface must be profiled to achieve maximum bond
strength.
Application
Conditions /
Limitations
Substrate Temperature +8C min. / +35C max.
Ambient Temperature +8C min. / +35C max.
Application
Instructions
Mixing Used as slurry: A : B = 1 : 4 (parts by weight)
Used as mortar: A : B 1 : 4.5 - 5.1 ( parts by weight)
Mixing Time ~ 3 minutes
Mixing Tools SikaTop

Seal-107 must be mechanically mixed using a forced action mixer or in a

clean drum using a drill and paddle (max. 500 rpm). A normal concrete free fall
mixer is NOT suitable.
Application Method /
Tools
Shake part A before using it. Pour approximately half of part A into the mixing
container and add part B slowly while mixing. Add the remainder of part A and
continue mixing until a uniform lump free consistency is achieved. The surface must
be pre-wetted to a saturated surface dry condition before application.
As a slurry:
Apply the mixed SikaTop

Seal 107 either mechanically, by spray or by hand using

a stiff brush. Applied in the same direction.
Apply the 2
nd
coat of SikaTop

Seal-107, applied by brush in crosswise direction to

the first application as soon as first coat has hardened.
As a mortar:
When SikaTop

Seal-107 is applied by trowel (e.g. for a smooth surface finish), the

product must be mixed with a 10% reduction of part A (~ 1A : 4.5 5.1B).
Apply the 2
nd
coat of SikaTop

Seal-107 as soon as the first coat has hardened.

For a smoother finish apply at 1.5mm maximum. For pore / blowhole filling, tightly
trowel into the pores / blowholes of the surface before main application.
Cleaning of Tools Clean all tools and application equipment with clean water immediately after use.
Hardened / cured material can only be removed mechanically.
Potlife ~ 30 minutes at +20C
Waiting Time /
Overcoating
Waiting time between coats
+10C ~ 12 hours
+20C ~ 6 hours
+30C ~ 3 hours
If waiting time period exceeds 24 hours, lightly blastclean the surface.
SikaTop

Seal-107 can be overpainted using solvent based primers or coatings.

SikaTop

Seal-107 must cure for a minimum of 7 days before overcoating.

4 4/5
SikaTop Seal-107
Notes on Application /
Limitations
SikaTop

Seal-107 is not a decorative treatment and may display signs of

blooming after rain or in damp weather. This does not affect the performance of
the coating, in any way. Where SikaTop

Seal-107 will be visible after completion of

the works, then the off-white colour, which is aesthetically more pleasing, should be
used. Trial areas should be conducted prior to application to ensure the required
application can be achieved.
Avoid application in direct sun and/or strong wind. Do not add water in any
circumstances. Apply only to sound, prepared substrates. Do not exceed maximum
layer thickness.
For waterproofing or damp proofing application, always use at least 2 coats to give
a total thickness of between 1.5 to 2.0 mm. In areas of severe water penetration,
three coats might be required.
Protect freshly applied material from freezing conditions and rain etc.
SikaTop

Seal-107 does not provide a traffickable finish. Use Sika

-1 Finishing
Mortar for trafficked surface or protect with a SikaTop

-77, SikaCem

-810 or
SikaLatex

bonded screed.
For waterproofing / damp-proofing works, special attention is required to avoid
puncturing the waterproof coating with fixings. These must be accommodated by
surface bonding with either Sikadur

-31 or Sikaflex

PRO-11 FC etc.
When used in contact with drinking structures, ensure that all associated Sika

products and construction materials also comply with the local regulations for
drinking water contact.
Curing Details
Curing Treatment It is essential to cure SikaTop

Seal-107 immediately after application for a

minimum of 3 to 5 days to ensure full cement hydration and to minimise cracking.
Use polythene sheeting or similar approved methods.
Value Base
All technical data stated in this Product Data Sheet are based on laboratory tests.
Actual measured data may vary due to circumstances beyond our control.
Local Restrictions
Please note that as a result of specific local regulations the performance of this
product may vary from country to country. Please consult the local Product Data
Sheet for the exact description of the application fields.
Health and Safety
Information
For information and advice on the safe handling, storage and disposal of chemical
products, users shall refer to the most recent Material Safety Data Sheet containing
physical, ecological, toxicological and other safety-related data.
Legal Notes
The information, and, in particular, the recommendations relating to the application
and end-use of Sika products, are given in good faith based on Sika's current
knowledge and experience of the products when properly stored, handled and
applied under normal conditions in accordance with Sikas recommendations. In
practice, the differences in materials, substrates and actual site conditions are such
that no warranty in respect of merchantability or of fitness for a particular purpose,
nor any liability arising out of any legal relationship whatsoever, can be inferred
either from this information, or from any written recommendations, or from any other
advice offered. The user of the product must test the products suitability for the
intended application and purpose. Sika reserves the right to change the properties
of its products. The proprietary rights of third parties must be observed. All orders
are accepted subject to our current terms of sale and delivery. Users must always
refer to the most recent issue of the local Product Data Sheet for the product
concerned, copies of which will be supplied on request.


5 5/5
SikaTop Seal-107

CE Labelling The harmonised European standard EN 1504-3 Products and systems for the
protection and repair of concrete structures Definitions, requirements, quality control
and evaluation of conformity Part 3 Structural and non-structural repair specifies
the identification, performance (including durability) and safety of products and
systems to be used to repair concrete surfaces (either building or civil engineering
structures).
Non-structural repair fall under this specification they need to be CE-labelled as per
Annex ZA.2, table ZA.2 conformity 2+ and fulfil the requirements of the given
mandate of the EU Construction Products Directive (89/106/CE).
Water Vapour Permeability Class 1
Capillary Absorption 0.1 kg.m
2
.h
0.5

Adhesion > 1.0 N/mm
2

Dangerous Substances Complies with 5.4




0086


Sika Ltd,
Welwyn Garden City,
Herts AL7 1BQ, UK

09

0086 CPD - 541325


BS EN 1504 -2

Surface Protection Systems


C
o
n
s
t
r
u
c
t
i
o
n


Sika Limited
Watchmead
Welwyn Garden City
Hertfordshire
AL7 1BQ
United Kingdom
Phone +44 1707 394444
Telefax +44 1707 329129
[Link]
email: sales@[Link]







Certificate No. EMS 4308 Certificate No. FM 12504