Scribd
Upload
271 views2 pages

Kinetics AF Isolation Hangers Overview

This document provides information about Kinetics Noise Control ceiling isolation hangers. It describes two models of isolation hangers - the AF-100 for lighter ceilings from 20-100 lbs and the AF-200 for heavier ceilings from 50-200 lbs. Both models can carry 100% overload without failure. The hangers improve the sound transmission class rating of ceilings by minimizing sound and vibration transfer using fiberglass isolation pads encased in steel brackets. They are recommended for use in acoustically isolated ceiling systems to reduce noise from mechanical equipment and increase sound blocking.

Uploaded by

onspsnons
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
271 views2 pages

Kinetics AF Isolation Hangers Overview

This document provides information about Kinetics Noise Control ceiling isolation hangers. It describes two models of isolation hangers - the AF-100 for lighter ceilings from 20-100 lbs and the AF-200 for heavier ceilings from 50-200 lbs. Both models can carry 100% overload without failure. The hangers improve the sound transmission class rating of ceilings by minimizing sound and vibration transfer using fiberglass isolation pads encased in steel brackets. They are recommended for use in acoustically isolated ceiling systems to reduce noise from mechanical equipment and increase sound blocking.

Uploaded by

onspsnons
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd

KINETICS NOISEAFCONTROL

Isolation Hanger
Ceiling Isolation Hangers greatly improve the STC rating for the
ceiling assembly by minimizing Sound/Vibration transfer
Model

Load Range

Max. Deflection

AF-100
AF-200

20-100 lbs (9-46 kg)


50-200 lbs (23-91 kg)

0.27" (6 mm)
0.18" (4 mm)

Kinetics Model AF Hangers are recommended for use in acoustically isolated ceiling systems. AF Hangers
are available in two (2) load ranges:
1) Model AF-100 load range, 20-100 pounds (9-46 kg), used for acoustical tile and gypsum
board ceilings.
2) Model AF-200 load range, 50-200 pounds (23-91 kg), used for heavy gypsum board and
plaster ceilings.
Both Model AF Hangers will carry a 100% overload without failure. Acoustical tile ceilings can be supported
by Model AF-100 Hangers to stop high frequency buzzing of the ceiling grid work, caused by equipment
such as transformers, chillers, and other mechanical equipment sources in the audio frequency range.
Heavy ceilings of gypsum board and plaster can be supported by Model AF Hangers to increase the sound
transmission loss. Standard Model AF Hangers are shipped fully assembled and ready to use. Special
accessories are available to eliminate bottom tie wire connections.

6300 Irelan Place


Dublin, OH 43017
1.800.959.1229 Toll-Free
[Link]

Over 50 years of success solving acoustic and noise control problems!

T E C H N I C A L

I N F O R M A T I O N

AF Isolation Hanger
Description

Applications

Model AF fiberglass Hangers are specifically


designed as a noise stop isolator for use in wiresupported, suspended ceiling systems. These
hangers are a combination of uniquely
permanent, fiberglass isolation pads and a
zinc-plated metal assembly. This creates a
combination that is non-corrosive in all typical
interior environments. The incorporation of
standard galvanized suspension wire adapts
the Model AF hanger directly into the tie wire
system used by ceiling installation trades.
Hangers are typically located a maximum 48
inches on center both ways.

Music Practice/Rehearsal Spaces


Music Performance Spaces
HVAC Equipment Rooms
Generator Rooms
Offices located below noisy equipment
Any room requiring improved noise control
through the ceiling

Composition
Hangers shall consist of a fiberglass isolator
encased in a zinc-plated steel bracket which
will accommodate up to No. 8 gauge suspension wire or a 1/4 (6.35 mm) bolt

17/64 dia. hole

4 3/4

Sound/Vibration Isolation Pad

Download the
Specification in
CSI Masterformat at
[Link]
Please contact your factory representative for design layout, specifications and pricing

01/09

You might also like