5670 TWIN TRIODE TUBES Five-Star Tube kkk FOR GENERAL-PURPOSE APPLICATIONS MEDIUM MU SHOCK, VIBRATION RATINGS 9-PIN MINIATURE HEATER-CYCLING RATING HIGH TRANSCONDUCTANCE DESCRIPTION AND RATING ‘The 5670 is a miniature medium-mu twin triode each section of which has 1 separate cathode connection. The tube is suited for use in a wide-variety ‘of general-purpose amplifier ond mixer circuits as well as numerous multi- vibrator and oscillator applications. The useful operating range extends from low frequencies through the VHF region. ‘The 5670 is a special-quality tube intended for use in critical industrial ‘and military applications in which operational dependability is of primary importance. Features of the tube include a high degree of mechanical strength ‘and a heater-cathode construction capable of withstanding many-thousand cycles of intermittent operation. When used in on-off control applications, the ‘tube will maintain its emission capabilites after long periods of operation under cutoff conditions. Analysis of the electrical characteristics of this tube with those of the 2C51 will indicate that the 5670 is essentially similar. GENERAL ELECTRICAL Cathode—Cooted Unipotential Heater Voltage, AC or DC. .63%10% Volts Heater Current.....+.. 035 Amperes Direct interelectrode Copacitanct Grid to Plate, Each Section . 1d as Input, Each Section. 22 put ‘Output, Each Section. ......sseseeesees 1.0 at Grid to Grid ee + 0.0017 put Plate to Plate. . 0.05 yf * Without extemal shield. MECHANICAL ‘Mounting Position—Any Envelope—T-6%4, Glass Base—£9-1, Small Button 9-Pin GENERAL @ ELECTRIC Spares FTONS dated 854 BASING DIAGRAM ‘TERMINAL CONNECTIONS Pin \—Heoter Pin 2—Cathode (Section 2) Pin 3—Grid (Section 2) Pin 4—Plate (Section 2) Pin 5—Internal Shieldt Pin 6—Plate (Section 1) Pin 7—Grid (Section 1) Pin 8—Cathode (Section 1) Pin 9—Heater { It is recommended that Pin 5 be grounded. PHYSICAL DIMENSIONS RETHA 6-15670 fee? MAXIMUM RATINGS ABSOLUTE MAKIMUM VALUES, EAGH SECTION Plate Voltage 5 pe ee 330 Volts Positive DC Grid Voltage... 0 Volts Negative DC Grid Voltage —55 Volts Plate Dissipation. eee Pee 11.35 Watts DC Grid Current 3.0 Milliamperes DC Cathode Current. 2.00.22 e cles fetes. 18 Milliemperes Heater-Cathode Voltage Heater Positive with Respect to Cathode eae 100 Volts Heater Negative with Respect to Cathode =... Bn peeeciel2t 100 Volts Grid Circuit Resistance... beset) 05 Megohms Bulb Temperature at Hoitest Point. pe 11685 € CHARACTERISTICS AND TYPICAL OPERATION CLASS A, AMPLIFIER, EACH SECTION Plate Voltage.....-2.+.2sceeceseseeesseecseees Volts ‘Ohms. ‘Ohms Transconductance . ‘Micromhos Plate Current Milliamperes Grid Voltage, approximate Ib=10 Microamperes —8 Volts PUSHL-PULL CLASS AB, AMPLIFIER Plate Voltage Volts Cothode-Bias Renee eee enemas Ohms AF Grid-to-Grid Voltage, RMS. Volts Zere-Signal Plate Current, Each Sec Milliamperes ‘Moximum-Signal Plate Current, Each Sect Milliamperes Effective Load Impedance, Plate-to-Plate... ‘Ohms Total Harmonic Distortion, approximate eae Percent ‘Maximum-Signal Power Output......--00000 200 svcseeeeee Watts CLASS A RESISTANCE-COUPLED bees eA SECTION LOW IMPEDANCE DRIVE APPROXIMATELY 200 O15) Ebb = 100 Volts | ets = 300 volte. Trey te maxiaum pus volts sieely tive percent to Ebb = 90 volte 2. Gain Ts measured for an output volt Wott fase 37 Tao | a5] 24 30 fo.24| 2400 | 8.2] ax | a0 | 22 | 25 | s500 | 57 | 27 Zafp.24] 900 ['7-¢] 21 | 3400 | a8 | @ | 3000 | 33 | 2 [Link]| sro | 9.7] 2 | e300 | 23 | 24 | 400 | 41 | 25 -sifp-si] 12000 | 8-5] 20 | va00 | 2] 22 | 7e00 | 36 | 2 3000 | 10 | 21 | seco | 26 | 23 | ozo HIGH IMPEDANCE ORIVE (APPROXIMATELY 100K OWS) 3. fy Ie In ohm oh RL ANd Rigg are In ‘A. coupling eapscitors (C1 should be Give desires frequency respons coquately by-pass Fob = 00 volts | ebb = 190 volts | ebb = Re | fo [oan] RG [Sein] he ‘600 | 9.2] 20 | 1500 | 21] 23 | 1100 300 | 12 | x | 2000 | a | 24 | 500 6200 | ii | | 4100 | 2] @ | 3200 7500 | 14 | ax | soco | 32] 23 | 4300 Tao | a2 [20 | sa00 [as | 2 | 700 ssoon | 15 | 20 [ssen0 | 34 | 22 | 9700 JANUARY 4, 19565670 ET-T1083A Poop CHARACTERISTICS LIMITS Minimum Maximum Heater Current EF=63 volts... 330 370 _—Milliamperes 330 370 —Milliamperes 330 370 ~—Milliamperes Plate Current, Each Section Ef=6.3 volts, Eb = 150 volts, Rk=240 ohms, (bypassed) 59 105 —Miilliomperes Plate Current Difference between Sections Difference between plate currents for each section at Ef=6.3 volts, b= 150 volts, Rk=240 ohms, (bypassed)... .. Initial 1.8 Milliomperes Transconductance (1), Each Section Ef=6.3 volts, Eb= 150 volts, Rk=240 ohms, (bypassed)... Initil 45006500 Micromhos Transconductance Change with Heater Voltage, Each Section Difference between Transconductance (1), and Transconductance ot Ef=57 volts (other conditions the same) expressed os © percentage of Transconductance (I)... -..eeevcseeveeee itil . 15 Percent ‘500 Hr 15 Percent Transconductance Change with Operation, Each Section Difference between Transconductance (1) initially and after operation expressed as a percentage of initial value : . ‘500 Hr 20 Percent 1000 Hr 25 Percent Average Transconductance Change with Operation, Each Section ‘Average of valves for ""Transconductance Change with Operation”. .. .500 Hr 15 Percent ‘Amplification Factor, Each Sect EF =6.3 volts, Eb = 150 volts, Rk=240 ohms, (bypassed)... «tnt 2 Ad Plate Current Cutoff (1), Each Section Ef =6.3 volts, Ebb = 150 volts, Ee= —10 volts, R,=0.25 meg Plate Current Cutoff (2), Each Section EF =6.3 volts, Eb = 150 volts, Interelectrode Capacitances 45 Microamperes Initial 50 + Microamperes Grid to Plate (g to p), Each Sect 14 aut Input (g to k-+h), Each Section... 27 unt ‘Output (p to k-th, Each Section 13 auf Plate to Plate (p to p).--.--0. 000.0 Ol ak ‘Measured without external shield Negative Grid Current, Each Section EF=6.3 volts, Eb =150 volts, Rk=240 ohms, (bypassed) Rg =0.5 meg... Initial 0 03 Microomperes 500 Hr 0 03 Microamperes 1000 Hr = «003 Microamperes Heater-Cathode Leckage Current, Each Section 33 volts, Ehk= 100 volts Heater Positive with Respect to Cathode... ssbitial 7.0 Microamperes 500 Hr 70 1000 Hr 79 7.0 — Microamperes 79 — Microamperes 7.0 — Microamperes dic interelectrode voltage is such that no cathode emission results. Grid (Each Section) to All at 100 Volts DC. . 100 ‘Megohms 50 ‘Megohms Plate (Each Section) to All at 300 Volts DC. 100522) Megohms 50 Megohms ‘CHARACTERISTICS LIMITS CONTNUED ON PAGE 45670 ET-TIO83A, Page 4 ae CHARACTERISTICS LIMITS (Cont'd) Vibrational Noise Output Voltage, RMS Minimum Maximum Ef=633 volts, Ebb = 150 volts, Ec= —3.0 volts, R,=2000 ohms, vibrational acceleration =2.5 G at 25 cps. Sectionsin parallel . ‘i ial ae 100 Millvolts Grid Emission Current, Each Section EF=7.5 volts, Eb = 150 volts, Ece= —10 volts, Rg=0.5 meg. ........ Initial 0 05 —Microamperes ‘The indicated 500-hour and 1000-hour values are life-test end points for the following conditions of operation for each section: Ef'= 6.3 volts, Eb= 150 volts, Rk=240 ohms, Rg=0.5 meg, Ehk=135 volts with heater positive with respect to cathode, and bulb temperature =165 C minimum. SPECIAL TESTS AND RATINGS Stability Life Test Statistical sample operated for one hour to evaluate and contro! initial variations in transconductance, Survivel Rate Life Test ‘Sotistical sample operated for one hundred hours fo evaluate and control early-lfe electrical and mechanical inopera- fives. Heater-Cycling Life Test Statistical sample operated for 2000 cycles to evaluate and control heater-cathode defects. Conditions of test include Ef=7.5 volts cycled for one minute on and one minute off, Eb=Ec=0 volts, and Ehk=135 volts with heater positive with respect to cathode. Shock Rating—600 G ‘Statistical sample subjected to five impact accelerations of 600 G in each of four different positions. The accelerating forces are applied by the Novy-type, High Impact (flyweigh!) Shock Machine for Electronic Devices or its equivalent. Fatigue Rating—2.5 G ‘Stotistical sample subjected to vibrational acceleration of 2.5 G for 32 hours minimum in each of thr ‘The sinusoidal vibration is applied at a fixed frequency between 25 and 60 cycles per second. Altitude Rating—60,000 Feet Statistical sample subjected to pressure of 55 mi Note: The conditions for some of the indicated tests have deliberately been selected to aggravate tube foilures for test and evaluation purposes. In no sense should these conditions be interpreted as suitable circuit operating condi- fons. In the design of specification. dif ferent positions, eters of mercury fo evaluate and control arcing and corona. Jory equipment employing this tube, reference should be made to the appropriate MIL-E-1C5670 ET-TIO83A Page 5 AVERAGE PLATE CHARACTERISTICS a EACH SECTION Ey = 6.3 VOLTS (OR GRO () CURRENT IN MILLAMPERES a ° 100 200 300 400 PLATE VOLTAGE IN VOLTS ra. 10,1983 AVERAGE TRANSFER CHARACTERISTICS EACH SECTION 2 PLATE CURRENT IN MILLIAMPERES ou a2 10 6 8 m4 ~2 ° ‘GRD VOLTAGE IN VOLTS na 10,19835670 Er-r1080, rege 8 AVERAGE CHARACTERISTICS se 10 cag sign 00 se 000 e000 qm F 25000) H $000 ai ae 8 z 5 3 3 no 3 ss 200 B° 3 2 &§ ts ™ 10000 2000 atte so 5 a ° s 10 15 20 PLATE CURRENT IN MILLAMPERES. ‘ocronee 9, 1953 ELECTRONIC COMPONENTS DIVISION GENERAL @ ELECTRIC Schenectady 5, N. Y. TTRANSCONDUCTANCE (G,) IN HICROMHOS