This Tecumseh Manual is a free download

from
[Link]

Tecumseh TC Series 2 cycle engines manual

Downloaded from [Link] manuals search engine

 TECUMSEH
T E C H N I C I A N ' S H A N D B O O K

This manual covers all TC, TCH 200 & 300 models.

TC
SERIES 2-
Cycle

Downloaded from [Link] manuals search engine

 CONTENTS
CHAPTER 1 GENERAL INFORMATION.............................................................................. 1
ENGINE IDENTIFICATION
......................................................................................................................1 OIL
REQUIREMENTS ..............................................................................................................................1
FUEL REQUIREMENTS ..........................................................................................................................2
STORAGE ................................................................................................................................................3

CHAPTER 2 AIR CLEANERS ............................................................................................. 4

GENERAL INFORMATION
......................................................................................................................4
OPERATION.............................................................................................................................................4
TROUBLESHOOTING .............................................................................................................................4
SERVICE ..................................................................................................................................................4
PAPER FILTER REMOVAL AND REPLACEMENT
.................................................................................5 POLYURETHANE
FILTER REMOVAL AND SERVICE ...........................................................................5

CHAPTER 3 CARBURETORS AND FUEL SYSTEMS....................................................... 6

GENERAL INFORMATION
......................................................................................................................6
OPERATION.............................................................................................................................................6
FUEL PRIMERS .......................................................................................................................................7
COMPONENTS ........................................................................................................................................7
TILLOTSON CARBURETOR
...................................................................................................................8
TROUBLESHOOTING .............................................................................................................................9
TROUBLESHOOTING CARBURETION - TC SERIES.....................................................................10-11
TESTING ................................................................................................................................................12
SERVICE ................................................................................................................................................12
CARBURETOR PRE-SET AND ADJUSTMENT....................................................................................12
FUEL TANK SERVICE ...........................................................................................................................13
CARBURETOR DISASSEMBLY ............................................................................................................13
CARBURETOR INSPECTION ...............................................................................................................14
CARBURETOR ASSEMBLY ............................................................................................................ 14-15

CHAPTER 4 GOVERNORS AND LINKAGE..................................................................... 16

GENERAL INFORMATION
....................................................................................................................16
OPERATION...........................................................................................................................................16
COMPONENTS ......................................................................................................................................16
TROUBLESHOOTING ...........................................................................................................................17
ENGINE OVERSPEEDING ....................................................................................................................17
ENGINE SURGING ................................................................................................................................17
SERVICE ................................................................................................................................................17
GOVERNOR ADJUSTMENT ........................................................................................................... 17-18

CHAPTER 5 REWIND STARTERS.................................................................................... 19

GENERAL INFORMATION
....................................................................................................................19

C Tecumseh Products Company

1998

Downloaded from [Link] manuals search engine

 CHAPTER 6 IGNITION ....................................................................................................... 21
GENERAL INFORMATION
....................................................................................................................21
OPERATION...........................................................................................................................................21
COMPONENTS ......................................................................................................................................21
TROUBLESHOOTING ...........................................................................................................................22
TESTING ................................................................................................................................................23
SERVICE ................................................................................................................................................23
AIR GAP SETTING ................................................................................................................................23
SPARK PLUG SERVICE ........................................................................................................................23

CHAPTER 7 INTERNAL ENGINE AND CYLINDER......................................................... 24

GENERAL INFORMATION
....................................................................................................................24
OPERATION...........................................................................................................................................24
COMPONENTS ......................................................................................................................................24
TROUBLESHOOTING ..................................................................................................................... 25-26
TESTING ................................................................................................................................................27
ENGINE KNOCKS..................................................................................................................................27
ENGINE OVERHEATS ...........................................................................................................................27
SURGES OR RUNS UNEVENLY ..........................................................................................................27
MISFIRES...............................................................................................................................................27
ENGINE VIBRATES EXCESSIVELY
..................................................................................................... 2 8 LACKS POWER
.....................................................................................................................................28
SERVICE ................................................................................................................................................28
GENERAL INFORMATION
....................................................................................................................28
DISASSEMBLY PROCEDURE ........................................................................................................ 28-29
BEARING AND SEAL SERVICE............................................................................................................30
ASSEMBLY....................................................................................................................................... 31-33

CHAPTER 8 ENGINE SPECIFICATION AND SEARS CRAFTSMAN

CROSS-REFERENCE ............................................................................................... 34
TC TORQUE SPECIFICATIONS............................................................................................................34

Downloaded from [Link] manuals search engine

 CHAPTER 1 GENERAL INFORMATION
ENGINE IDENTIFICATION
TC engine identification numbers are stamped into the blower housing or blower housing base near the spark plug, or a
decal is permanently attached to the side of the blower housing (diag. 1-1).

Identification Decal
Identification Decal

TC TYPE I ENGINE TC TYPE II ENGINE 1-1

The engine identification decal will include the model

number, specification number, warranty code, and date of
manufacture (diag. 1-2).
TC300 3133C (B) 5114G
The model number designation following TC (Tecumseh
Compact) indicate the cubic inch displacement of the
engine. TC 300 indicates a 3.0 cubic inch displacement. Model Specification Date of Manufacture
Number Number Warranty or Serial Number
The number (3133C) following the model number is the Code
specification number. The last two numbers and letter 1-2
character (33C) indicate a variation to the basic engine
specification. SHORT BLOCK IDENTIFICATION TAG
The warranty code letter (B) indicates the length of SBV or SBH Identification number
warranty that is supplied by Tecumseh.
The DOM (Date of Manufacture) or Serial Number
indicate the date the engine was produced. The first SBV1543
year in the decade (1995). The next three digits (114)
indicate the Julian build date (114 th day or April 24). The
letter designation indicates the line or shift on which the SER 4201
engine was built at the factory.
Short blocks are identified by a tag marked SBH (Short Serial Number or DOM
Block Horizontal) or SBV (Short Block Vertical) (diag. 1-3
1-3).

CAUTION: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH IF NOT FOLLOWED
COULD ENDANGER THE PERSONAL SAFETY OF YOURSELF AND OTHERS. FOLLOW ALL
INSTRUCTIONS.

OIL REQUIREMENTS
TECUMSEH RECOMMENDS USING TWO CYCLE OIL PART #730227, which is a premium blend that ensures cylinder
wall lubrication, mixes easy, does not separate and is specially formulated for use in air or water cooled two cycle engines.
Tecumseh two cycle engines require the use of a NMMA TC-W3 or TC-WII certified oil.
The proper fuel mixture ratio of oil to gasoline for specific engines will be found in the owners operating instructions and
on the decal attached to the blower housing or fuel tank of the engine.

1
Downloaded from [Link] manuals search engine
 FUEL REQUIREMENTS
24:1 FUEL MIXTURE CHART ALL TC ENGINES
Tecumseh Products Company strongly recommends the
use of fresh, clean, unleaded regular gasoline in all NOTE: DO NOT MIX FUEL IN ENGINE OR
Tecumseh engines. Unleaded gasoline burns cleaner, EQUIPMENT FUEL TANK.
extends engine life, and promotes good starting by U.S. METRIC
reducing the build-up of combustion chamber deposits.
Leaded gasoline, gasohol containing no more than 10% Gas Oil To Be Added Petrol Oil To Be Added
ethanol, premium gasoline, or unleaded gasoline
1/2 Gal. 3.00 oz. 2 Liters 83 ml.
containing no more than 15% MTBE (Methyl Tertiary Butyl
Ether), 15% ETBE (Ethyl Tertiary Butyl Ether) or 10% 1 Gal. 6.00 oz. 4 Liters 167 ml.
ethanol, can be used if unleaded regular gasoline is not
available. 2 Gal. 11.00 oz. 8 Liters 333 ml.

Reformulated gasoline that is now required in several areas

of the United States is also acceptable.
MIXING OIL AND GASOLINE PROCEDURE
NEVER USE gasoline, fuel conditioners, additives
1. Fill approved, clean container one quarter full with
or stabilizers containing methanol, gasohol containing
the recommended gasoline.
than 10% ethanol, unleaded regular gasoline containing
more than 15% MTBE (Methyl Tertiary Butyl Ether), 15% 2. Add the recommended amount of oil to the
ETBE (Ethyl Tertiary Butyl Ether) or 10% ethanol, gasoline gasoline.
additives, or white gas because engine/fuel system
damage could result. 3. Secure the cap on the container and shake the
container vigorously.
See “STORAGE” instructions in Technician’s Manual,
Operator’s Manual, or Bulletin 111. 4. Remove the cap, add the remainder of the gasoline,
secure the cap, re-mix. The fuel is ready to use.
For year round fuel stability in and out of season, use 1-4
Tecumseh's fuel stabilizer part number 730245.

FUEL ADDITIVES
Only fuel additives such as Tecumseh's fuel stabilizer part number 730245 or liquid varieties can be used when mixed
properly. For winter applications, Isopropyl alcohol fuel dryers may be used in the fuel system but must be mixed at
the proper ratio recommended by the manufacturer. NEVER USE METHANOL BASED DRYERS.
Gasoline and oil containers must be clean, covered, and rust-free. Old gas or fuel contamination can restrict or block fuel
filters, and small fuel ports and passages in the carburetor. If the engine is to be unused for 30 days or more see
"Storage" for fuel system instructions.

TUNE-UP PROCEDURE
The following is a minor tune-up procedure. If the engine does not perform properly after the tune up is completed,
consult the "Troubleshooting Engine Operation Chart" found in Chapter 7. Repair procedures are listed in each chapter.

CAUTION: REMOVE THE SPARK PLUG WIRE BEFORE DOING ANY SERVICE WORK ON THE ENGINE.

1. Service or replace the air cleaner as necessary. Use the applicable procedure found in Chapter 2 under "Service".
2. Remove the fuel from the fuel tank by running the engine until stopping or draining into an approved fuel container.
3. Remove the fuel tank and blower housing to clean all debris from the air intake screen, cylinder cooling fins,
governor and carburetor linkage.
4. Replace the blower housing and check all remote linkage for proper adjustment and operation.
5. Check to see that the engine is properly secured to the equipment. On rotary lawnmowers, balance the blade
and check the blade hub and crankshaft key for wear. Replace as necessary. Torque the bolts to the correct
specification.
6. Replace the spark plug with the correct replacement by using the Master Technician's Parts Manual. Set the
spark plug gap at .030" (.762 mm) and install it in the engine. Tighten the spark plug to 230 inch
pounds (2.6 Nm) of torque. If a torque wrench isn't available, screw the spark plug in as far as possible by hand.
socket or wrench to turn the spark plug 1/8 to 1/4 turn further if using the old spark plug, or 1/2 turn further if a
new spark plug is used. Reinstall the spark plug wire.

2
Downloaded from [Link] manuals search engine
 TUNE-UP PROCEDURE (continued)
7. Fill the fuel tank with the proper fuel/oil mix.
8. Start the engine and allow it run 3 - 5 minutes to reach operating temperature. Adjust the carburetor if necessary
(see Chapter 3 under "Service" for the final idle mixture adjustment procedure) and set the engine R.P.M.(s)
according to the specification number found on microfiche card # 30 or computer parts look up system.

STORAGE (IF THE ENGINE IS TO BE UNUSED FOR 30 DAYS OR MORE.)

CAUTION: NEVER STORE THE ENGINE WITH FUEL IN THE TANK INDOORS OR IN ENCLOSED, POORLY
VENTILATED AREAS, WHERE FUEL FUMES MAY REACH AN OPEN FLAME, SPARK OR PILOT LIGHT AS
ON A FURNACE, WATER HEATER, CLOTHES DRYER, OR OTHER GAS APPLIANCE.

Gasoline can become unstable in less than 30 days and form deposits that can impede proper fuel flow and engine
operation. To prevent deposits from forming, all gasoline must be removed from the fuel tank and the carburetor. An
acceptable alternative to removing all gasoline is adding a fuel stabilizer to the gasoline such asTecumseh part number
730245. A fuel stabilizer is added to the fuel tank or storage container. Always follow the mix ratio and mixing procedure
found on the stabilizer container. Run the engine at least 10 minutes after adding the stabilizer to allow it to reach the
carburetor.
Draining The Fuel System
1. Remove all gasoline from the fuel tank by running the engine until the engine stops, or by draining the fuel tank
by removing the fuel line at the carburetor. Be careful not to damage the fuel line or the carburetor fitting.

CAUTION: DRAIN THE FUEL INTO AN APPROVED CONTAINER OUTDOORS, AND AWAY FROM ANY
OPEN FLAME OR COMBUSTIVE SOURCE. BE SURE THE ENGINE IS COOL.

2. If "Gasohol" has been used, complete the above procedure and then put 2 ounces (60 ml) of the recommended
fuel / oil mixture using regular unleaded gasoline into the fuel tank. Run the engine until it stops due to a lack of
fuel. If "Gasohol" is allowed to remain in the fuel system during storage, the alcohol content may cause gaskets
and seals to deteriorate.
Oil Cylinder Bore
1. Remove the spark plug wire from the spark plug. Pull the starter handle slowly until resistance is felt due to
compression pressure, then stop. Slowly release starter tension to prevent the engine from reversing due to
compression pressure.
2. Remove the spark plug, squirt 1/2 ounce (15 ml.) of clean 2-cycle engine oil into the spark plug hole.
3. Cover the spark plug hole with a shop towel and crank the engine over, slowly, several times.
4. Replace the spark plug and tighten (see step # 5 under Tune-Up Procedure for proper spark plug torque). Pull
the starter handle as performed in step # 1. The piston position blocks the cylinder ports,
air from entering and oil from leaving the cylinder bore during storage.
5. Replace the spark plug wire on the spark plug.

3
Downloaded from [Link] manuals search engine
 CHAPTER 2 AIR CLEANERS

GENERAL INFORMATION
The air cleaner is designed to eliminate dust and dirt from the air supply. Most models of 2-cycle and 4-cycle engines
use an air cleaner except engines that run in clean environments like snow throwers or ice augers. On these applications,
a filter is not necessary and could collect snow or moisture and prevent proper engine operation. On most applications,
filtered air is necessary to assure abrasive particles are removed before entering the combustion chamber. Dirt allowed
into the engine will quickly wear the internal components and shorten the life of the engine.
Tecumseh engines use either a polyurethane or a paper type air filter system. A polyurethane pre-filter or a flocked
screen may be used in conjunction with the main filter. Extremely dirty operating conditions may require frequent filter
cleaning or replacement.

OPERATION
The outer cover holds the air filter element(s) and prevents debris from entering the filter box. The air supply is filtered
through the pre-filter if equipped, filter element (polyurethane or paper), and a flocked screen if equipped. Pre-filter
elements do not extend the recommended air filter service intervals listed under "Service". However; in extremely dirty
operating conditions a pre-filter element may increase the run time of the engine before the filter becomes restricted (not
to exceed the service recommendations), and service on the filter is necessary.

TROUBLESHOOTING
If the engine's performance is unsatisfactory (needs
Polyurethane Filter
excessive adjustments, starts smoking abnormally, loses
power), the first component to be checked is the air cleaner. Air Cleaner Screen
A dirt restricted or an oil soaked filter element will cause
noticeable performance problems. A polyurethane element
may be cleaned following the service procedure listed
under "Service" in this chapter. A paper-type air filter should
only be replaced. Follow the procedure listed in the
service section in this chapter for replacement. Re-try the
engine after filter replacement or service. If the problem
after filter service, see Chapter 7 under "Troubleshooting" 2-1
for additional causes.

SERVICE
Cleaning and oiling the polyurethane element (diag. 2-1) Cover
is recommended every three (3) months or every 25
operating hours. If the engine is used in extremely dusty
Air Cleaner
or dirty conditions, the filter may require service every
three hours or as often as necessary to maintain proper Collar
engine
performance.
Polyurethane type filters require re-oiling after extended
storage due to oil migration out of the filter.
A paper type element (diag. 2-2) should be replaced once
extremely dusty conditions. Use only original factory
recommended replacement filters.
Clamp
NOTE: DO NOT ATTEMPT TO CLEAN OR OIL PAPER
FILTERS. 2-2

4
Downloaded from [Link] manuals search engine
 Paper Filter Removal and Replacement
1. Remove the polyurethane pre-filter (if equipped) from
the air filter.
Poly Pre-Filter
2. Inspect the filter(s) for discoloration or dirt accumulation.
(For the polyurethane pre-cleaner service see step #
5 under "Polyurethane Filter Removal and Service").
If either condition is present, replace the paper type
filter using the following steps.
Air Cleaner
3. Loosen the clamp and slide the clamp toward the air
filter. (diag. 2-3) Hose Clamp
Clamp
4. Slide the air filter and clamp off the carburetor adapter.
Carburetor Adapter
Discard the old filter and keep the clamp.
5. Apply a thin layer of silicon sealant to the outside of Carburetor
the air cleaner adapter.
6. Install the clamp on the new air filter, slide the 2-3
filter assembly onto the carburetor adapter as far as
it will
go.
Screen A
7. Slide the clamp as close to the carburetor as possible. Screen B
Tighten the clamp securely.

Polyurethane Filter Removal and Service

Kleen Aire® Air Cleaner or TC Type II
1. Remove the cover by pulling outward on the tab (diag. Polyurethane Filter 2-4
2-4). On the TC Type II style engine, loosen the two
screws (diag. 2-5).
2. Remove screen A (if equipped), foam filter and screen Lock Nut
B from the air cleaner body (diag. 2-4). On TC Type II
engines, remove the flocked screen and the foam filter Washer
(diag. 2-5).
3. Inspect the flocked screen and foam filter for
is present, service the element or screen using the
following steps.
Fuel Tank
4. The flocked screen pre-filter may be cleaned by blowing
compressed air through the screen from the back side.
Replace the screen if this procedure does not fully
remove the accumulated particles.
5. Wash the polyurethane filter or polyurethane pre-filter
(used with paper air filters) in a detergent water
solution and squeeze (don't twist) until all dirt is
removed.
Air Cleaner
6. Rinse the polyurethane filter or polyurethane pre-filter Housing
thoroughly in clean water. Wrap the filter in a clean
cloth and squeeze (don't twist) until completely dry.
Poly Air-Cleaner
7. Saturate the polyurethane filter with engine oil and Flocked Screen
squeeze (don't twist) to distribute and remove excess
oil. Air Cleaner Cover
Cover Screw

2-5

5
Downloaded from [Link] manuals search engine
 CHAPTER 3 CARBURETORS AND FUEL SYSTEMS

GENERAL INFORMATION
TC engines almost exclusively use diaphragm-type carburetors to be able to run effectively at any operating angle. The
diaphragm carburetors are produced by Walbro and Tillotson for Tecumseh. The carburetors use an internal diaphragm fuel
pump to supply the fuel to the carburetor fuel metering chamber. The metering diaphragm has one side exposed to
intake manifold pressure and one side exposed to atmospheric pressure. This diaphragm provides the same basic function
(maintaining the proper fuel level in the carburetor) as the float.
A limited number of TC engines were produced as outboards using a Tecumseh Series II float style carburetor. Consult the
Two Cycle Technician's Handbook (part # 692508) if service is required on this series of carburetor.
When servicing carburetors, use the engine model and specification number to obtain the correct carburetor part number. An
alternate method to find the correct carburetor part number on float type carburetors is to use the manufacturing
number and date code stamped on the carburetor and convert this number to a part number. In the carburetor section of the
Master Parts Manual or Microfiche Catalog, a cross reference chart will convert a carburetor manufacturing number to a
Tecumseh part number.

OPERATION
In the "CHOKE" or "START" position, the choke shutter is
closed, and the only air entering the engine flows through
openings around the choke shutter. As the recoil assembly Fuel
is operated to start the engine, downward piston travel
Impulse
creates a low pressure area in the engine cylinder above the
Intake Air
piston. Higher pressure atmospheric air rushes into
Engine Vacuum
the engine to fill the created low pressure area. Since the
majority of the air passage is blocked by the choke shutter, a
relatively small quantity of air enters the carburetor at
increased speed. The main nozzle and both idle fuel
discharge ports are supplying fuel due to the low air
pressure in the intake of the engine and the fuel side of
the main diaphragm. Atmospheric air pressure on the
opposite side of the main diaphragm forces the diaphragm Start 3-1
upward, depressing the inlet control lever, overcoming inlet
spring pressure and allowing fuel to enter the fuel chamber
through the inlet valve. A maximum fuel flow through the Fuel
carburetor orifices combined with the reduced quantity of Impulse
air that passes through the carburetor, make a very rich fuel Intake Air
mixture which is needed to start a cold engine Engine Vacuum
(diag. 3-1).

At IDLE the throttle shutter is almost closed, the low

pressure acts only on the primary idle fuel discharge port
due to throttle plate position. A relatively small quantity of fuel
is needed to operate the engine (diag. 3-2).
Idle 3-2

During INTERMEDIATE throttle operation, the secondary

Fuel
idle fuel discharge port supplies fuel after it is uncovered
by the throttle plate. As the throttle plate opens Impulse
progressively further, engine speed increases. The velocity Intake Air
of air going through the carburetor venturi creates a low Engine Vacuum
pressure area to develop at the main fuel discharge port
while diminishing the effect of the low pressure area on the
engine side of the throttle plate. When the pressure at the
venturi throat is less than that existing within the fuel
chamber, fuel is forced through the high speed mixture
orifice and out the main fuel discharge port (diag. 3-3).
Intermediate 3-3

6
Downloaded from [Link] manuals search engine
 At high speed operation, the throttle shutter is in a full open
position. The air velocity through the venturi increases which Fuel
further lowers the air pressure at the main fuel Impulse
discharge port. All discharge ports are supplying fuel as the Intake Air
adjustment orifices will allow (diag. 3-4). Engine Vacuum

The fuel pump diaphragm in the carburetor moves up and

down by pressure changes (pulsations) caused by piston
movement. The pulsations are transferred to the pump by
a passage called the impulse channel. The pump
diaphragm moves up drawing fuel into the pump fuel
chamber during a positive pulse, and a negative pulse
moves the diaphragm down forcing fuel out of the fuel High Speed 3-4
chamber through the inlet needle into the metering
chamber.

FUEL PRIMERS
Primers used on TC engines supply a solid fuel charge to the
carburetor main nozzle (diag. 3-5). Fuel is forced directly
into the carburetor venturi. A choke shaft and
shutter is not needed or used when a primer is used. This
charge of fuel provides the rich mixture necessary to start the
engine.
3-5
Below the main nozzle is a one way check valve to prevent
fuel from being drawn back into the fuel chamber when the
primer bulb is released. The check valve also prevents
air from entering the carburetor during normal engine 1
operation.
2

COMPONENTS
WALBRO CARBURETOR 4
6
1. Diaphragm Cover Screw 17. Throttle Shaft
12 5
2. Metering Diaphragm Cover 18. Throttle Shaft Return Spring 7
3. Diaphragm 19. Throttle Shutter Screw 8
21 9 10 11
4. Diaphragm Gasket 20. Throttle Shutter 13
5. Metering Lever 21. Fuel Fitting
14
6. Metering Lever Screw 22. Fuel Inlet Screen
7. Metering Lever Pin 23. Pump Diaphragm
19
8. Metering Lever Spring 24. Pump Cover Gasket 27
9. Inlet Valve Needle 25. Pump Cover 28 15
10. Inlet Valve Seat 26. Pump Cover Screw
20 22 29 18
11. Welch Plug 27. Tension Spring
12. Choke Shaft 28. Dust Seal
17
13. Choke Shutter Screw 29. Dust Seal Washer 23
14. Choke Shutter
15. Idle Mixture Screw
16. Idle Speed Screw 24

25
27
26 16

3-6

7
Downloaded from [Link] manuals search engine
 TILLOTSON CARBURETOR

1. Diaphragm Cover Screw

2. Metering Diaphragm Cover
3. Diaphragm
4. Diaphragm Gasket
5. Metering Lever
6. Metering Lever Screw
7. Metering Lever Pin
8. Metering Lever Spring
9. Inlet Valve Needle
10. Air Vane
11. Air Vane Screw
12. Dust Seal
13. Dust Seal Washer
14. Dust Seal Retainer
15. Idle Mixture Screw
16. Idle Speed Screw
17. Throttle Shaft
18. Throttle Shaft Return Spring
19. Throttle Shutter Screw
20. Throttle Shutter
21. Fuel Fitting
22. Fuel Inlet Screen
23. Pump Diaphragm
24. Pump Cover Gasket
25. Pump Cover
26. Pump Cover Screw
27. Tension Spring
28. Main Mixture Jet
29. Welch Plug

8
Downloaded from [Link] manuals search engine
 ENGINE TROUBLESHOOTING

Engine Will Not Start

NO See Chapter 6
Check For Spark
under "Troubleshooting"
YES

WET
Check If Spark Plug Is Wet or Dry

Check Fuel Supply and Fuel Cap

Defective Spark Plug
Vent

Restriction in Fuel System

Restricted Air Filter
(filter, screen)

Carburetion Problem
Improper or Stale Fuel

Carburetion Problems Due to

Flooding, Over Priming, etc. Poor Compression

Blockage in Pulse Channel to

Ignition System Carburetor

Plugged Muffler or Exhaust Port

9
Downloaded from [Link] manuals search engine
 TROUBLESHOOTING CARBURETION - TC SERIES

N
en t

tle
IO
tm

rot
ing

AT
jus

Th
nn

ER
Ad
n N tor
Ru

ing
EL
e

en t
e W arbur

s
ot

ed

o
DE
qu

T.
C
lo s

n
Fre
C

.O.
n

tio
hen
N&
he

eC

dli
rom

ate

at W
d)

era
ed s

f
le I

sW

Of
ed l
pee

IO

ler

cel
gF

Ne

D
i
AT

cce

rop
Ne

Wh
n

n
g

wS

top

c
EE
e
pin

u
rtin

hA
Idl
ng

er
le

R
R
e

hD
th

eS

SP
Idl

Up
(Lo

eed

ow
rip

LE
sE

ot
dle
Sta

Wi
ot

ot

ric
T

Ric
ll N
gin
el D

ll N

ll N
atic

GH

wP
CE
AR

ads
"N
hI
od

er-
LE

es
rd

En
ADJUSTMENTS

Wi
Ric

AC
Flo

No
ST

Err

Ov
Id l

HI
Wi

Lo

Wi
Ha

Lo
Fu

ID

"L
Low l l l
l l l l

High l l l l l

FUEL SYSTEM

Plugged Tank Filter or Vent l l l l l l l

Restricted Fuel Line l l

l l l
Leak in Pulse System l l l l l l l Restricted Pulse

Channel l l l l l l l Loose Pump Cover

Screws l l l l l l

Defective Pump Diaphragm l l l l l l l

AIR SYSTEM

Plugged Air Filter l l l l l l Defective M

l l l l l Loose Carb. Mountin

l l l l Worn Throttle Shaft or Valve

l l

Incorrect Throttle Assembly

Loose Throttle Valve Screw l

Throttle Shaft Too Tight l

Bent Throttle Linkage l

Defective Throttle Spring l

Bent Throttle Stop Lever l

Choke Not Functioning Properly l

Worn Choke Shaft or Valve l l

10
Downloaded from [Link] manuals search engine
 TROUBLESHOOTING CARBURETION - TC SERIES
(CONTINUED)

N
en t

IO

ttle
tm
ing

AT

hro
jus
nn

ER

gT
Ad
or
Ru

EL
ret

sin
en t

EC
ot
rbu

ed

Clo
qu
N

T.
D
lo s
Ca

ng

ion
Fre

.O.
n

N&

hen
e

eC

dli
rom

rat
Wh

at W
d)

rat
ed s

I
ed l

sW

ele
pee

TIO
ile

ele
gF
ine

Ne

D
c
Ne

Wh

un
g

c
EE
top
e

RA
pin
rtin

hA
Idl
ng

er
le

R
e

A
th

SP
Idl

Up
(Lo

eS
eed

ow
rip

LE
sE

ot
dle
Sta

Wi
ot

ot

ric
T

ll N
el D

ll N

ll N
atic

GH

wP
gin
CE
AR

ads
"N
hI
od

er-
LE

es
rd

METERING SYSTEM

Wi
Ric

AC
Flo

En
ST

Err

Ov
Id l

HI
Wi

Lo

Wi
Ha

Lo
Fu

ID

"L
LEVER
Worn Lever l

Set Too High l l l l l l l

S e t To o L o w

l l l l

Not Free l l l l l l l

SPRING
Improperly Installed l l

DIAPHRAGM

Leaking (Air/Fuel) l l l l l l

Worn Button l

Improper Assembly l l l l

Defective Gasket l l l l l
Loose Diaphragm Rivet l l

Hole in Diaphragm l l l l l

Loose Cover Screws l l l l l l

INLET NEEDLE & SEAT

Foreign Matter l l l l l l l l

Binding l l l l l l l l l l l

Worn Needle Body or Tip l l l l l

NOZZLE CHECK VALVE l l l l l l

11
Downloaded from [Link] manuals search engine
 TESTING
1. After repeated efforts to start the engine using the procedure listed in the operator's manual fail, check for spark by
removing the high tension lead and removing the spark plug. Install a commercially available spark plug tester and check
for spark. If the spark is bright blue and fires every revolution, proceed to step # 2. If no spark, weak spark, or
intermittent spark see Chapter 6 "Ignition" under "Troubleshooting".
2. Remove the spark plug and visually check the removed spark plug for a wet condition indicating the presence of fuel
mixture in the cylinder.
3. If the spark plug is dry, check for restrictions in the fuel system before the carburetor. If the spark plug is wet, continue with
step # 6. Check the fuel cap vent, the cap must allow air to be blown through it when testing. Using a proper draining
receptacle, remove the fuel line from the carburetor inlet fitting (Type I) or fuel tank (Type II) and pull
off the fuel line. Examine the fuel flow and fuel condition. Improper fuel flow indicates the fuel, fuel line, filter, or tank
require cleaning or replacement.
4. Visually inspect the choke shutter for complete closing or check to see fuel flowing from the main nozzle during priming. Remove
the air cleaner element or air cleaner assembly to provide access for visual inspection.
5. If the fuel flow to the carburetor is adequate and no fuel flows out the main nozzle during priming or choking, the carburetor
will require service. Consult the Troubleshooting Carburetion Chart for possible causes for the lack of
fuel.
6. Check the engine compression using a commercially available compression tester and follow the tester's
recommended procedure. Low compression, no fuel present on the spark plug, adequate fuel flow and a known
good functional carburetor indicates an internal engine problem exists. See Chapter 7 under "Troubleshooting".

SERVICE
CARBURETOR PRE-SET AND ADJUSTMENT
Both the Walbro and the Tillotson carburetors used on TC
engines have non-adjustable main mixture jets. Only the
idle mixture is adjustable by turning the idle mixture screw. Use
the following procedure to pre-set the idle mixture
screw. Turn the idle mixture screw (clockwise) finger tight to
the closed position, then turn the screw counterclockwise to
obtain the proper preset (diag. 3-7).
Walbro model WTA, WT 1 - 1 1/8 turns
Tillotson model HU 1 1/4 - 1 3/8 turns

Final Idle Mixture Adjustment

Idle Mixture Screw
Start the engine and allow it to reach normal operating 3-7
temperature (after 3-5 minutes). As the speed control is
set at the idle position, turn the idle mixture screw slowly
clockwise until the engine R.P.M. just starts to decrease.
Stop and note this screw position. Turn the idle mixture screw
slowly counterclockwise. The engine will increase R.P.M.
Continue to slowly turn the screw until the engine
R.P.M. starts to decrease. Note this position and turn the
mixture screw back clockwise halfway between the two
engine R.P.M. drop off positions. The idle mixture
adjustment is complete.

12
Downloaded from [Link] manuals search engine
 FUEL TANK SERVICE
1.
TC type II engines have fuel tanks with an integral fuel screen
and integral outlet fuel fitting. Some TC type I engine
models use a pressed in fuel filter or a weighted filter and a
flexible fuel line in the tank. Integral screens or fittings
are not serviceable. Pressed in fuel filters and fittings can be
serviced using the following procedure (diag. 3-8). 2.
1. Press the fuel fitting into the tank and feed the fuel line in until
the filter can be removed through the filler neck.
Remove the filter and fuel line if necessary.
2. To install a new filter and fuel line, push the new fuel line
through the tank outlet until the fuel line protrudes
through the filler neck.
3. On tanks without weighted filters, push a new filter on the
fuel line. For weighted filters, slide the new retaining
ring on the fuel line protruding from the filler neck. Push 3.
the fitting into the line to the fitting shoulder. Slide
the retaining ring over the groove in the fitting and
crimp the retaining ring using a pliers.
4.
4. Attach the fuel line and weighted fuel filter if applicable.
Pull the fuel line through the tank outlet. The filter barb
or the fuel fitting barb must protrude from the tank.

CARBURETOR DISASSEMBLY
3-8
1. Note or mark the location and sequence of the
diaphragm(s), gasket(s), and the metering or pump
cover. Remove the screw(s), gaskets, and Dust Seal Retainer
diaphragms. Metering Lever
Metering Lever Pin
2. Remove the idle mixture screw. On Tillotson model
HU carburetors, remove the plastic screw or brass plug Dust Seal
Washer Metering Lever Screw
over the main mixture jet and remove the main mixture Metering Lever Spring
jet if necessary for cleaning (diag. 3-9). Dust Seal

Inlet Valve Tension Spring

3. Use a 8-32 tap with the tapered flutes removed to turn
Needle Idle Mixture
into the brass welch plug until it bottoms and begins
Screw
to turn the welch plug. Carefully pull the welch plug
from the carburetor body.
Fuel Inlet Welch Plug
4. Note or mark the location and action of the throttle and Screen
Main Mixture Jet Throttle
air vane, and choke shaft (if applicable). Remove Shutter
the screw holding the throttle or choke shutter to the Throttle Screw
shaft. Remove the Torx T8 screw (use part # 670334) Shutter
holding the air vane to the throttle shaft if applicable. Dust Seal
Remove the clip screw, dust seal retaining clip, and Dust Seal Washer
throttle shaft. On some older Walbro carburetors it is
Throttle Shaft Return Spring
necessary to remove the circlip on the end of the
throttle shaft to remove the shaft (diag. 3-9).
Throttle Shaft
5. Remove the inlet needle valve, metering lever, and 3-9
metering lever spring by removing the retainer screw
on the pivot pin (diag. 3-9).
Note: Do not allow chisel point to strike
6. Remove the fuel inlet screen and check valve screen carburetor body or channel reducer
Pry out
using an "O" ring pick. Remove all welch plugs using plug
a sharpened small chisel. Drive the sharpened chisel
into the welch plug, push down on the chisel to pry Ò
Pierce plug with tip
the welch plug out of position. Be careful not to damage
the carburetor body (diag. 3-10). Welch Plug
7. On Walbro carburetors, the fuel inlet fitting can be
removed with a pliers using a twisting and pulling
1/8"
motion. Do not re-use the old fuel fitting. The fuel fitting
on Tillotson carburetors is not replaceable. Do not Ô
remove. Carburetor cleaner will not affect this fitting. Ô
Small Chisel 3-10

13
Downloaded from [Link] manuals search engine
 8. Clean all metallic parts in carburetor cleaner. Do not Note: Punch should be of the
exceed 30 minutes soak time. Blow out all fuel same or larger diameter than
passages with compressed air. Do not use tag wire to the welch plug.
clean the orifice in the main mixture seat assembly. The
main mixture seat assembly contains a teflon disc
check valve. If the disc is damaged with tag wire, the Flat End
Punch
carburetor will not function properly.

CARBURETOR INSPECTION
Visually examine the throttle lever shaft and choke shaft for
wear at the bearing points in the carburetor body.
Inspect the pump and metering diaphragms for hardness,
fuel contamination, holes or tearing in the diaphragm.
Pump diaphragm flapper valves should appear flat with
New Welch
no curling. Check the inlet screen and check valve screen for Plug 3-11
contamination. Check the atmospheric vent hole in the
metering cover and clean if necessary.
Carburetor Face
Check the inlet needle for wear on the taper portion of the
needle. Replace as necessary.

CARBURETOR ASSEMBLY
Inlet Needle
1. Install new inlet screen(s) using a small flat punch
slightly smaller than the screen. Push in until the Metering Pin
screen contacts the seat.
2. If removed, install the high speed jet. Use a slightly larger
flat punch to install the brass welch plug over
Metering Lever Tip
the high speed jet. The closed, tapered end of the plug 3-12
goes toward the jet. Tap the brass welch plug in
until it is flush with the carburetor body. Apply sealant
like fingernail polish to the brass plug.
3. Install new welch plug(s) using a flat punch equal to or 1
slightly larger than the plug. The welch plug(s)
must be flattened by taps with a small hammer on the 1. Metering Diaphragm Cover
2. Diaphragm
installing punch. Sealant such as fingernail polish 3. Diaphragm Gasket
is recommended to apply to an installed welch plug. 4. Pump Diaphragm 2
Use sparingly and wipe off excess immediately 5. Pump Cover Gasket
(diag. 3-11). 6. Pump Cover

4. Install the inlet needle, spring, metering lever and 3

pin. The metering lever hooks on the inlet needle
and rests on the metering spring. Install as an
assembly and install the retaining screw
(diag. 3-12).
5. Check the metering lever tip height using a metering
lever gauge (part # 670325). The tip height should
be .060" to .070" (1.52 mm to 1.77 mm) from the
face of the carburetor body on Walbro carburetors.
On Tillotson carburetors the tip of the metering lever
should be flush with surface of the carburetor body.
6. Install the idle mixture screw and spring and back the
4
screw out from the closed position 1 - 1 1/8 turns
for Walbro, 1-1/4 - 1-3/8 turns for Tillotson
carburetors.
7. Install the metering diaphragm, cover gasket, and 5
cover. Place the cover gasket (over the locator pins on
Walbro only) on the carburetor body, add the
metering diaphragm with the long rivet head toward
the carburetor body on top of the gasket, add the
6
cover and fasten the four screws (diag. 3-13).

3-13

14
Downloaded from [Link] manuals search engine
 8. Install the pump gasket over the locator pins on the
pump cover, add the pump diaphragm next, and
place the assembly on the carburetor body. Check
to see that the locator pins fit the corresponding holes
in the carburetor body. Install the pump cover
retaining screw (diag. 3-13).
9. If removed on Walbro carburetors, install a new fuel inlet
fitting in the same position as the original (diag. 3-14).
When installing a new fitting, insert the tip into
the carburetor body, then coat the exposed portion of
the shank with Loctite grade A (red), then press it in
squarely using support on the opposite side to THROUGH HOLE
TOWARD SPARK
prevent damage to the carburetor body or fitting. PLUG
Press it in until the fitting bottoms out in the carburetor
body.
VACUUM CHANNEL
10. Install the choke and throttle shaft assemblies in the TOWARDS CYLINDER
reverse order of removal. Visually check for proper
operation of the choke and throttle. 3-14

NOTE: Do not re-use old choke or throttle plate shutter screws. New screws are treated with a dry Loctite adhesive to
secure them in place.
11. If applicable, attach the air vane and torque the mounting screw to 3-5 inch pounds (.34 - .57 Nm) (diag. 3-14).
12. Newer style TC series engines use an insulator / spacer between the carburetor and cylinder. That spacer MUST be
installed, as shown, for the fuel pump to operate.

EMISSIONIZED TC CARBURETOR
The Tillotson carburetor is now an emissions grade carb. It has a married idle and high speed circuitry with limited jet
adjustments on the idle.

EMISSIONS CARBURETOR IDLE MIXTURE

ADJUSTMENT PROCEDURES
The carburetor is preset at the factory at a normal setting
required for initial engine operation.
Allow the engine to reach normal operating temperature
(after 3-5 minutes).
Set the engine speed control in the idle position. With the
engine at idle speed (Note: must be less than 2400 R.P.M.
for accurate adjustment). Using a small tip screw driver that
fits through the access hole in the limiter cap, adjust the
mixture screw slowly clockwise until the engine R.P.M.
just starts to decrease. Stop and note this screw position.
Turn the idle mixture screw slowly counterclockwise. As the
engine increases R.P.M. continue to slowly turn the
screw counterclockwise until the engine R.P.M. starts to
decrease. Note this position and turn the mixture screw back
clockwise halfway between the two engine R.P.M.
drop off positions.
Verify the engine will accelerate from low speed to high speed
and that the idle speed remains at the desired
setting.
Once adjustments are complete, center the adjustment
limiter cap between the two stops and press inward to
engage the limiter. The limiter will snap into position and
engage the adjusting screw. All future adjustments should
now be made using the adjusting slot in the limiter cap.
CAUTION: Once the limiter cap is snapped into place it is not
possible to remove the limiter or to adjust the mixture screw
beyond the limits of the limiter assembly. Make sure 3-15
that initial adjustments are made per the above procedure
15
prior to engaging the limiter cap.
Downloaded from [Link] manuals search engine
 CHAPTER 4 GOVERNORS AND LINKAGE
GENERAL INFORMATION
TC series engines are equipped with pneumatic (air vane) governors. The governor's function is to maintain a R.P.M.
setting when engine loads are added or taken away. Air vane governors are controlled by the air velocity created by fins
on the flywheel. Changes in the engine R.P.M. cause the air vane to move. This
movement opens the throttle shaft either by a link between the air vane and the throttle plate, or the air vane is mounted
directly onto the throttle shaft. The throttle is opened as the engine R.P.M.
drops and is closed as the engine load is removed.
This chapter includes governor assembly linkage and speed control illustrations to aid in assembly.

OPERATION TYPE I
Engine R.P.M. changes cause an increase or decrease in
velocity exerts pressure on the air vane while a governor
spring exerts pressure against the air velocity force. The
air vane pivots on the engine blower housing base or is
attached to the throttle shaft of the carburetor. As an
engine load is applied and the engine's R.P.M drop, the air
velocity also drops, allowing the governor spring to pull
open the
throttle shaft and increase engine speed (diag. 4-1).
If the engine uses a remote speed control, the bowden
shaft. Moving the speed control plunger results in
changing the governor spring tension which increases or
decreases the engine's governed speed. TYPE II

COMPONENTS
1. AIR VANE
2. BACKLASH SPRING
3. GOVERNOR LINK
4. GOVERNOR SPRING
5. MOUNTING SCREW
6. SPEED ADJUSTMENT SCREW
7. SPEED CONTROL BODY
8. SPEED CONTROL LEVER
9. SPEED CONTROL PLUNGER 4-1

1.
TYPE II TYPE I
1. 5.

8.
Spring Hooked
In Notch

9. 4.

2.

4.
Insert Throttle Link

7. 3.

6. 4-2

16
Downloaded from [Link] manuals search engine
 TROUBLESHOOTING
ENGINE OVERSPEEDING
1. If the engine runs wide open (faster than normal), shut the engine off or slow it down immediately.
2. Visually inspect the air vane, linkage, carburetor throttle shaft, and speed control for debris blockage, binding,
breakage, or incorrect hook-up. Check the governor spring for a stretched or distorted condition. Remove the recoil
assembly and / or fuel tank if necessary. See "Disassembly Procedure" in Chapter 7.
3. Clean, correct or replace binding or damaged parts. Set the speed control to the recommended engine R.P.M.

ENGINE SURGING
1. Try to stabilize the engine R.P.M. by holding in one position the carburetor throttle shaft on the exterior of the
carburetor.
2. If the engine R.P.M. stabilizes, the governor or governor adjustment should be checked. Follow the procedure under
"Governor Adjustment" in this chapter. If the engine R.P.M. does not stabilize, the engine will require additional
checks see Chapter 3 under ''Troubleshooting".
3. If the problem persists after the governor adjustment, check the engine R.P.M. found on microfiche card # 30 or in
the computer parts lookup. If the setting for high and low speed are within the listed specification and a slight surge
is
experienced, increasing the engine idle speed slightly may eliminate this condition.
4. Visually inspect the air vane, linkage, carburetor throttle shaft, and speed control for debris blockage, binding,
breakage, or incorrect hook-up. Check the governor spring for a stretched or distorted condition. Remove the recoil
assembly and/or fuel tank if necessary. See "Disassembly Procedure" in Chapter 7. Repair or replace as necessary.

TYPE I
SERVICE
For governor disassembly or assembly procedures see
"Service" in Chapter 7. Spring Hooked
In Notch
GOVERNOR ADJUSTMENT
Three different styles of governor systems are used on TC
engines. Use the following illustrations (diags. 4-3, 4-4 Speed
Adjusting
and 4-5) to identify the governor system used and the Lever
following procedure to adjust the governed engine speed.
1. Allow the engine to run for at least 5 minutes to reach
the operating temperature. Make sure the air filter (if
equipped) is clean and the choke is in the off position. Decrease
Ý Increase
2. Using a Vibratach (part # 670156) or other tachometer,
Ý
determine the engine's R.P.M at idle and wide open
throttle. Consult microfiche card # 30 or the computer
parts lookup to obtain the recommended engine
speeds. TYPE I

3. Using the applicable illustration, either bend the speed

adjusting lever toward the spark plug end of the
opposite direction to increase R.P.M. On TC Type II Spring Hooked
engines, turn the speed adjusting screw out to In Notch
increase or in to decrease engine high speed R.P.M. If
adjustment screw is turned out to increase the engine
R.P.M., the speed control lever must be moved to allow
Speed
the speed control plunger to contact the speed Adjusting
adjustment screw. Lever
4. The low speed is set by moving the throttle control to
the lowest speed position and adjusting the low speed
adjustment screw on the carburetor.

4-3

17
Downloaded from [Link] manuals search engine
 TYPE II

14
4
10
8
1
5 ADJUST GOVERNED HIGH SPEED WITH SPEED CONTROL PLUNGER
PULLED BACK AGAINST SPEED ADJUSTMENT SCREW
DECREASE INCREASE
SPEED ADJUST SCREW
13

12
AIR VANE MUST ROTATE 6 4
FREELY AFTER CLIP 9 11 3 2
7
IS INSTALLED

ITEM DESCRIPTION ITEM DESCRIPTION

1 Base - Housing 8 Spring - Governor
2 Body Assy. - Speed Control 9 Clip - Spring
3 Screw 10 Spring and Link Attachment
4 Throttle Plate 11 Speed Control Plunger
5 Air Vane 12 Speed Adjustment Screw
6 Spring - Backlash 13 Notch in Air Vane for Governor
7 Link - Governor Spring Attachment
14 Speed Control lever 4-4

TYPE II Spring Color Spring Position

Orange or Green 1
Decrease (IN)
Increase (OUT) Pink, Red, or Black 2
Speed Adjusting Screw

Spring Position 1

Spring Position 2
Adjust governed high speed with speed
control plunger pulled back against speed
adjustment screw

4-5

18
Downloaded from [Link] manuals search engine
 CHAPTER 5 REWIND STARTERS

GENERAL INFORMATION
TC series engines have the recoil assembly as a part of the engine's blower housing. Two different styles of recoil
starters are used along with different starter rope locations. Use the engine model and specification number to identify
the recoil style and correct replacement parts.

OPERATION
TYPE I
As the starter rope is pulled, the starter pulley rotates on
the center leg of the starter. The starter pawl is connected
to the starter pulley by an offset hole in the pawl and a 1
1
corresponding raised boss on the pulley. The pawl has a
oversize inside diameter which allows the pawl to be
pulled off center. The flat contact
with one of the flywheel fins. This engagement turns the
flywheel until the engine fires and the flywheel speed
exceeds the speed of the starter pulley. The flywheel fins 2 2
push the pawl (using the ramp side) to the disengaged
position. The brake spring slows the pulley and pawl from 3
turning (diag. 5-1).
4 4
TYPE II
This starter uses two engagement pawls bolted to the 3
flywheel with shoulder bolts. Each pawl uses an 5
engagement spring to keep the pawl in contact with the 8
pulley hub. The pawls lock into two of the four notched 6
surfaces when the starter rope is pulled. When the engine
fires and the flywheel speed exceeds the speed of the 7 9
starter pulley, the pawls disengage, and centrifugal force 10
keeps the pawls in the disengaged position (diag. 5-1). 8
11

COMPONENTS
1. Blower Housing 5. Pawl 9. Dog Screw 12
2. Recoil Spring 6. Brake Spring 10. Starter Dog 12
3. Washer 7. Retainer 11. Pawl Spring
4. Pulley 8. Retainer Screw 12. Flywheel
Type I Type II 5-1

SERVICE
Starter related problems will require the starter to be
removed from the engine to diagnose the cause. On TC
Type I engines, try starter operation off the engine to see
pawl engagement. Visually inspect the starter pawl, brake
spring, retainer, pulley, washer(s) and rope for wear or
breakage. Repair or replace as necessary. On TC Type II
engines, recoil disassembly is necessary only if the pulley
is worn, the recoil will not retract, or the rope needs
replacement. Check starter pawl engagement on the
flywheel for broken springs, sticking or bent condition, or
loose pawl screws.

DISASSEMBLY PROCEDURE
1. Remove the fuel tank spring and recoil assembly
from the engine. On TC Type II engines, the air filter
and fuel tank must be removed before the recoil
5-2
assembly.
19
Downloaded from [Link] manuals search engine
 2. Release the recoil spring tension on the rope by
removing the staple or knot in the starter handle
and slowly release the rope into the recoil housing
(diag. 5-2).
3. Remove the 5/16" retainer screw. On TC Type I
starters, remove the pawl retainer, brake spring,
and pawl.
4. Remove the starter pulley. Use caution if removal
the recoil spring if necessary.
CAUTION: BE CAREFUL NOT TO PULL THE
REWIND SPRING OUT OF THE BLOWER
HOUSING WHEN REMOVING THE STARTER
PULLEY. THE REWIND SPRING WILL UNCOIL
AND EXPAND WITH FORCE IF REMOVED
Lubricate Here
FROM THE BLOWER HOUSING.
5-3
ASSEMBLY PROCEDURE
1. Lightly grease the center leg and the area where
the rewind spring will rest in the blower housing Spring Tail
with "Chem-Lube" or "Lubriplate" (diag. 5-3).
2. Install a new starter spring if necessary. Securely
grip the rewind spring a short distance away from
the spring tail with a needlenose pliers. Position the
rewind spring in the blower housing and hook the
spring tail to the housing as shown. Make sure the
spring tail is fully seated before slowly releasing the
needlenose pliers from the spring. Push the coiled
spring into the recessed boss area and discard the
spring holder. Apply a thin coating of "Chem-Lube"
to the top of the spring (diag. 5-4). 5-4

3. Insert the starter rope into the starter pulley and tie
a left handed knot in the end of the rope. Wind the
starter rope counterclockwise (as viewed from the
pulley bottom) on the pulley and place the end of
the rope in the notch in the pulley (diag. 5-5).
4. Place the pulley in the blower housing, press down
and rotate the pulley until the pulley drops down
and catches the end of the rewind spring. On TC
Type II models, continue assembly at step 7
(diag 5-6).
5. Lightly grease the pawl retainer and place the pawl
(with the numbers up) on the retainer. Place 5-5 5-6
the
brake spring on the center of the retainer with the
tab locating the pawl (diag. 5-7).
6. Install the retainer, pawl, and spring assembly on
the center leg, locate the notch in the center leg Pawl
and the tab of the retainer and align when installing
(diag. 5-8).
7. Insert the retainer screw and torque to 30-40 inch Spring
pounds (3.4 - 4.5 Nm).
8. Use the starter rope or fingers to turn the pulley
and pre-wind the recoil spring a minimum of 1 3/4
and a maximum of 2 1/2 turns in a counterclockwise
Retainer
rotation.
9. Feed the starter rope through the starter grommet
5-7 5-8

20
Downloaded from [Link] manuals search engine
 CHAPTER 6 IGNITION

GENERAL INFORMATION
All TC engines are equipped with a solid state ignition module mounted outside the flywheel. The solid state ignition
system consists of a flywheel magnet, charge coil, capacitor, a silicon controlled rectifier, a pulse transformer, trigger coil,
high tension lead, and a spark plug. All components except the spark plug and high tension lead are located in an
encapsulated ignition module. The module is protected by epoxy filler from exposure to dirt and moisture. This system
requires no maintenance other than checks of the high tension lead and spark plug.

OPERATION
As the magnet in the flywheel rotates past the charge coil,
electrical energy is produced in the [Link] energy is
stored in the capacitor (approx. 200 volts) until it is
released by an electrical switch (SCR). As the magnet
continues to rotate, it passes past a trigger coil where a
signal is [Link] low voltage signal closes the SCR
switch, allowing the energy stored in the capacitor to flow
to a transformer where the voltage is increased from 200
volts to 25,000 volts. This voltage flows along the high
tension lead to the spark plug where it arcs across the
electrodes and ignites the air-fuel mixture (diag. 6-1).

6-1

COMPONENTS

2
1. FLYWHEEL WITH MAGNETS
2. FLYWHEEL KEY
3. IGNITION MODULE
4. SPARK PLUG
5. IGNITION SWITCH
3

6-2

21
Downloaded from [Link] manuals search engine
 IGNITION TROUBLESHOOTING

Engine Will Not Start Engine Runs Erratically

Or Shuts Off, Restarts

Check For Spark

SPARK NO SPARK

Check flywheel for damaged Replace spark plug

or sheared key

Isolate engine and repeat

test

Set proper air gap on solid SPARK NO SPARK

state module

Engine problem, check for

Equipment problem, check
shorts or grounds in wiring
switches, wiring and
equipment controls
Test solid state module for
intermittent or weak spark

Disconnect ignition cut-off

wire at the solid state
module and repeat test
Fuel system problem -
see Chapter 3 -
"Troubleshooting"
Check for proper air gap on
solid state module and
repeat test

Check flywheel magnets for

strength

Test solid state module

22
Downloaded from [Link] manuals search engine
 TESTING
1. Check for spark using a commercially available spark tester and following the tester's recommended procedure.
2. Check the spark plug for cracks in the porcelain, pitted or burned electrodes, excessive carbon build-up and
proper air gap setting. Replace if questionable.
3. Check the air gap between the ignition module and the flywheel magnet. See "Service" in this chapter.
4. Disconnect the ignition grounding lead at the ignition coil and crank the engine over. If spark occurs, check the
ignition switch or the electrical wiring for shorting to ground. If no spark, test the ignition module using a coil tester
or replace the ignition module.

SERVICE
AIR GAP SETTING
Timing on the solid state module is fixed. The air gap
dimension between the laminations of the ignition module and
is .0125" (.317 mm) (use gauge part # 670297) for TC 300
rotary mower engines and all TC 200 engines. All other
TC 300 applications require a .030" (.762 mm) air gap
dimension (use gauge part # 670321). Loosen the module
mounting bolts, insert the air gap gauge, hold the module
against the flywheel magnets and torque the mounting screws
to the specification. Remove the gauge and rotate the
flywheel to check for any possible striking points. If none are
found, the air gap is set correctly (diag. 6-3).
NOTE: When using the 670321 gauge push the module tight
to the flywheel before tightening.

SPARK PLUG SERVICE

Spark plugs should be removed, cleaned, and adjusted
periodically. If the porcelain shows cracking, or the electrodes
show evidence of pitting, burning, or excessive carbon build-
All TC300 non-rotary .0125" (.7317 mm)
up, replace the spark plug.
mower use .030" (.762 mm) part number 670297
NOTE: DO NOT USE A SAND BLASTER TO CLEAN SPARK Air gap part number 670321 All TC200 an TC300 rotary
PLUGS. MICROSCOPIC PARTICLES LEFT IN THE PLUG mower application 6-3
CAN SCORE THE ENGINE CYLINDER DURING
OPERATION. Use solvent and a wire brush to clean the plug
and compressed air to blow out completely.
Consult the Master Parts Manual for the correct spark plug
and replace if necessary. Set the spark plug gap at .030" (.762
mm) (diag. 6-4). Install the spark plug in the engine and tighten
to 230 inch pounds (2.6 Nm) torque. If a torque wrench is not
available, screw the spark plug in as far as possible by hand
and use a spark plug wrench to turn the spark plug 1/8 to 1/4
of a turn more if using the old plug, and a 1/2 of a turn more
if using a new spark plug.
.030"
(.762 mm)

6-4

23
Downloaded from [Link] manuals search engine
 CHAPTER 7 INTERNAL ENGINE AND CYLINDER
GENERAL INFORMATION
TC series engines use two cycle operation. Two cycle engines provide a higher horsepower to weight ratio than the
same size four cycle engines. Two cycle engines use two piston strokes for a complete cycle that occurs
every crankshaft revolution, while four cycle engines use four piston strokes and two crankshaft revolutions for a
complete cycle.
Lubrication is accomplished through oil mixed in the fuel, and the air / fuel / oil mixture flows into the crankcase during
upward piston travel. This mist lubricates all internal bearing surfaces.

OPERATION 1. 2.

A low pressure area is created in the crankcase as the

the cylinder. When the piston moves far enough to uncover
the intake port, the air / fuel mixture from the carburetor
flows into the engine crankcase due to higher pressure
atmospheric air. Just before the piston reaches top dead
center (TDC), the spark plug ignites the air / fuel mixture
in the cylinder.
3. 4.
The expanding combustion gases force the piston down.
The downward piston travel causes a pressure build-up in
the crankcase. The piston uncovers the exhaust port first
followed by the transfer ports. The exhaust flows out the
exhaust port while the pressurized air / fuel mixture enters
the cylinder from the crankcase through the transfer ports.
As the piston travels upward the sequence is repeated
(diag. 7-1).
7-1

COMPONENTS
1. CYLINDER
2. "G" CLIP
3. PISTON PIN
4. PISTON 6
5. ROD
6. CRANKCASE 2
7. CRANKSHAFT
8. COVER

1 3

7
8

7-2

24
Downloaded from [Link] manuals search engine
 TROUBLESHOOTING ENGINE OPERATION PROBLEMS

ENGINE MISFIRES ENGINE VIBRATES LACKS POWER

EXCESSIVELY

Wrong or fouled spark plug Bent crankshaft Air intake obstructed

Attached equipment out of Lack of lubrication or improper

Carburetor improperly adjusted lubrication
balance

Ignition timing Loose mounting bolts Carburetor improperly adjusted

Excessive carbon build up Exhaust Obstructed

Leaking seals or gaskets Loss of compression

Crankcase seals or gaskets

leaking

Choke, throttle, or governor not

operating properly

Ignition Timing

25
Downloaded from [Link] manuals search engine
 TROUBLESHOOTING ENGINE OPERATION PROBLEMS

ENGINE KNOCKS OVERHEATS SURGES OR RUNS

UNEVENLY

Associated equipment loose or Excessive engine loading Fuel cap vent obstructed
improperly adjusted

Check for excessive carbon in Lack or proper lubrication Dirty carburetor or air filter
combustion chamber

Cooling air flow obstructed or

Loose flywheel - examine key, clogged cooling fins Carburetor improperly adjusted
key way and proper flywheel nut
torque

Carburetor improperly adjusted or Governor sticking, binding or

Ignition timing improper RPM setting improper RPM setting

Loose or worn connecting rod Ignition timing Carburetor linkage, shafts or

shutters sticking or binding

Worn cylinder or piston Carbon in the combustion

chamber
Intermittent spark - check ignition
Offset piston incorrectly installed
Leaking seals or gaskets

26
Downloaded from [Link] manuals search engine
 TESTING
ENGINE KNOCKS
1. Check the blade hub, adapter, crankshaft coupler or associated equipment for loose fit, loose bolts, or crankshaft
key or adapter damage. Re-install and re-torque the bolts to the proper torque.
2. Check the flywheel key and the flywheel and crankshaft keyway for wear or partial shearing. Replace if any damage
is evident. Tighten the flywheel nut to the proper torque.
3. Check for the correct ignition module air gap. See Chapter 6 under "Service".
4. Remove the muffler and check for carbon build-up in the combustion chamber and exhaust port. Check the spark
plug for the proper reach and heat range (correct spark plug for the engine). Clean carbon build-up if necessary.
5. Check the internal components (piston, cylinder, connecting rod, and crankshaft journal) for excessive clearance
using a dial bore gauge, micrometer, and telescopic gauges.

ENGINE OVERHEATS
1. Make sure the engine is not being overloaded. Remove excess load (sharpen blades, limit operation speed, or
process less material).
2. Make sure the fuel mixture contains the correct ratio of certified 2-cycle oil to gasoline. Replace the fuel supply if
questionable.
3. Check for clogged cooling fins or obstructions to the air flow. Remove the rewind assembly, clean and reinstall.
4. Check the engine R.P.M. setting using a vibratach or other tachometer and compare it to the R.P.M. settings found
on microfiche card # 30 or computer parts lookup according to the engine model and specification number. Adjust
as necessary.
5. Remove the muffler and check for carbon build-up in the combustion chamber and exhaust port. Clean as necessary.
6. Check the carburetor for the correct idle mixture adjustment. Clean the carburetor if the problem persists see Chapter
3 under "Service".
7. Check for the correct ignition module air gap. See Chapter 6 under "Service".
8. Inspect the intake gaskets, crankcase seals or gaskets for a leaking condition. Use a commercially available
crankcase pressure tester and follow the tester's recommended test procedure. See "Disassembly Procedure " in
this chapter for component removal.

SURGES OR RUNS UNEVENLY

1. Check the fuel cap to make sure it is venting. Loosen the cap and retry engine operation.
2. Replace or clean the air filter if applicable.
3. Check the carburetor for the correct idle mixture adjustment. Clean the carburetor if the problem persists see Chapter
3 under "Service".
4. Check the engine R.P.M. setting using a vibratach or other tachometer and compare it to the R.P.M. settings found
on microfiche card # 30 or computer parts lookup according to the engine model and specification number. Adjust
as necessary.
5. Visually check all linkages. Check the governor spring for a stretched or damaged condition. Check the governor
shaft, throttle shaft, and pivot points for binding.
6. Check the ignition module operation using a gap type tester inserted in the high tension lead. Check for intermittent
spark.
7. Inspect the intake gaskets, crankcase seals or gaskets for a leaking condition. Use a commercially available
crankcase pressure tester and follow the tester's recommended test procedure. See "Disassembly Procedure " in
this chapter
for component removal.

ENGINE MISFIRES
1. Check the spark plug for a fouled condition. Replace if questionable.
2. Check the carburetor for the proper adjustments. See "Pre-sets and Adjustments" in this chapter.
3. Check the air gap dimension. Follow the procedure in Chapter 6 under "Service". Use an in-line spark tester to see
27
Downloaded from [Link] manuals search engine
 4. Check the flywheel key for partial shearing.
5. Remove the muffler to check for excessive carbon build-up in the combustion chamber or exhaust port.
6. Inspect the intake gaskets, crankcase seals or gaskets for a leaking condition. Use a commercially available
crankcase pressure tester and follow the tester's recommended test procedure. See "Disassembly Procedure " in
this chapter
for component removal.

ENGINE VIBRATES EXCESSIVELY

1. Remove the engine drive and check the attached equipment for an out of balance condition.
2. Check the engine mounting bolts, make sure they are tight.
3. Check the engine crankshaft on the P.T.O. end using a straight edge, square or dial indicator. Blades or adapters
must be removed. Any deflection will cause a vibration problem.
4. Check the internal engine for bearing roughness or wear, crankshaft bearing journal wear, or a worn cylinder or
piston.

LACKS POWER
1. Check the air intake for an obstruction (dirty filter, saturated filter, or other debris).
2. Check the exhaust for a restriction preventing proper exhaust flow.
3. Check the fuel / oil mixture for the gasoline being fresh and the proper amount and kind of oil used. Replace if
questionable.
4. Visually check the operation of the throttle, air vane governor, and choke (if applicable) for restrictions preventing
proper movement.
5. Check the carburetor for the correct idle mixture adjustment. Clean the carburetor if the problem persists see Chapter
3 under "Service".
6. Inspect the intake gaskets, crankcase seals or gaskets for a leaking condition. Use a commercially available
crankcase pressure tester and follow the tester's recommended test procedure. See "Disassembly Procedure " in
this chapter
for component removal.
7. Inspect the engine cylinder and ring(s) for a worn condition using an inside micrometer or dial indicator.
8. Check the flywheel key for partial shearing.

SERVICE
GENERAL INFORMATION
TC engines do not have oversize pistons available. If the engine bore diameter exceeds the maximum engine
Gaskets have replaced Loctite sealant between the engine cylinder and the crankcase. Crankcases that used Loctite
sealant between the cylinder cover and the engine crankcase have been upgraded to use an "o" ring in a machined
channel. Engines requiring replacement of the cylinder, cylinder cover, crankcase, or piston and rod assembly may
require the replacement of the short block or a complete engine. Consult the Tecumseh Master Technician's Parts
Manual using the engine model and specification number for replacement part information.

DISASSEMBLY PROCEDURE
1. Remove the high tension lead boot from the spark plug by twisting and pulling.
2. Remove the spark plug using a 3/4" (19 mm) deep well socket.
3. Drain the fuel from the tank by sliding the fuel line clamp off the carburetor fuel fitting (TC type I) or fuel tank fitting
(TC type II), twist and pull the fuel line off and drain the fuel into an approved container.
CAUTION: DRAIN THE FUEL INTO AN APPROVED CONTAINER OUTDOORS AND AWAY FROM ANY OPEN
FLAME OR COMBUSTION SOURCE. BE SURE THE ENGINE IS COOL.
4. Remove the two hex nuts on the carburetor studs and remove the air cleaner assembly. On TC type II engines,
remove the two screws on the filter cover, the filter element(s), and then the two hex nuts on the carburetor studs. If
the carburetor stud loosens; try retightening the hex nuts first, then loosen the nuts.

28
Downloaded from [Link] manuals search engine
 5. Remove the fuel tank on TC type I engines by
unhooking the tank spring. For TC type II engines,
remove the self-locking nut and washer on the blower
housing stud and remove the fuel tank.
6. Remove the rewind starter assembly by removing three
machine screws (diag. 7-3). Remove the rubber plugs.
7. Remove the ignition grounding lead off the ignition
module and remove the ignition module using a 1/4"
socket or Torx T15 drive.
8. Use the strap wrench (part # 670305) to hold the 7-3
flywheel and loosen the flywheel nut until it is flush
with the end of the crankshaft. Mounting Screws
9. Use flywheel puller (part # 670299) to pop the
flywheel off the crankshaft taper, unthread and
remove the puller. Remove the flywheel nut, washer,
flywheel and
flywheel key (diag.7-4).
NOTE: DO NOT USE A KNOCK-OFF TOOL ON THE
CRANKSHAFT WHEN REMOVING THE FLYWHEEL.
PERMANENT ENGINE DAMAGE MAY RESULT.
10. Mark or note the location of the throttle link, governor
Remove the carburetor, spacer, gaskets, and air baffle
if equipped using a 1/4" socket on the carburetor studs.
11. Remove the blower housing base by removing the
three 5/16" hex head screws (diag. 7-5). 7-4

12. Attach the engine tool holder (part # 670300) to the

crankcase using the three removed blower housing
base hex head screws. Place tool in a bench vise (diag.
7-6).
13. Remove the muffler using a 12" (304 mm) piece of
heavy gauge wire with a 1/4" (6.31 mm) hook on one
end to pull the muffler spring off (diag. 7-7). A diagram
of the wire hook is in the tool section of this manual.
On TC type II engines, remove the shoulder
bolts holding the muffler on. 7-5 7-6

14. Note or mark the location of the cylinder to the

crankcase and remove the four Torx bolts holding the
cylinder to the crankcase using a six inch long Torx
T30 driver (part # 670320). Pull the cylinder off squarely
using caution so the rod does not bend. Use a 3/8"
open end wrench to loosen the four cylinder nuts on
early production type I engines (diag. 7-8). 7-7
15. Insert seal protector (part # 670301) to protect the
flywheel end oil seal and seal protector (part #
670303) for the P.T.O. end oil seal (diag. 7-9).
16. Remove the crankcase cover screws and remove the
cover. On TC type II engines with a ball bearing in the
cover, the cover and crankshaft will be removed as an
assembly.

670301
670303

7-8

29
Downloaded from [Link] manuals search engine
 17. Turn the crankshaft to the 90° past the top dead center
(T.D.C.) position and remove the crankshaft out of the
crankcase opening while sliding the connecting rod
off the crankpin and crankshaft. TC type II engines Needle Bearing Cover
use a pressed in mechanically retained needle
bearing in the connecting rod. Older TC engines
crankpin needle bearings, make sure to collect all 23
needle bearings. Engines built after Aug. 1995 may
also use loose needle bearings (grease retained), 36
needles are required (diag. 7-9).
18. Use a bearing splitter and an arbor press to remove
the ball bearing and cover assembly from the
crankshaft on TC type II if necessary.
19. Remove the oil seals by supporting the area around
the seal and using a small punch or screwdriver
to
Ball Bearing Cover
drive out the seal.

BEARING AND SEAL SERVICE

The crankcase and crankcase cover oil seals can
On older TC engines, a retainer ring must be removed
with a pick before the crankcase bearing can be pressed
out (diag. 7-10).
Remove the needle bearing by using the bearing installer
tool (part # 670302) inserted from the outside to drive the
bearing out. 7-9

To install a new bearing in the engine crankcase, place a

new caged needle bearing on the installation tool (part # Retainer Ring
670302). Use bearing installation tool (part# 670304A) for
installing the crankcase cover caged needle bearing.
Place the printed side of the bearing toward the Oil Seal
installation tool. Lightly oil the outside of the bearing and
bearing bore. Press the bearing into the crankcase until Bearing
the tool is flush with the crankcase or cover housing. Insert
the retainer ring if applicable (diag. 7-11). 7-10

Install a new crankcase oil seal using seal protector /

installer (part # 670301). Use seal installer (part # 670303)
to install the crankcase cover oil seal. The metal case of
the seal goes onto the seal protector first. Lightly oil the
outside of the seal. Press the tool and seal in until the tool
is flush with the crankcase (diag. 7-12). 670302 670304A

Later production TC engines have a step machined in the

crankcase and crankcase cover bearing area. This
change eliminated the need for a retainer ring. The
seal installation tools (part # 670302, 670303, 670304A)
can be used with either style of crankcase cover. The 7-11
installation tools place the bearing in the cover or the
crankcase to the proper depth.
Models equipped with a ball bearing in the crankcase
cover can have the ball bearing removed using an arbor
with support placed near the bearing diameter. Press the
bearing out of the cover from the outside, pushing the 670303
bearing away from the machined step. 670301

A new crankcase cover ball bearing can be installed using

an arbor press. Press the bearing in until the bearing is
flush and the bearing contacts the machined step.
Seal protector / installer part # 670303 should be used to
install a new oil seal in the crankcase cover.
7-12

30
Downloaded from [Link] manuals search engine
 ASSEMBLY
1. Remove old gasket material. Be careful not to damage
scratch or burr the sealing surfaces. Clean the
crankcase, cylinder, piston assembly, crankshaft, and
crankcase cover using cleaning solvent and blow dry
with compressed air (diag. 7-13).
2. On TC type II engines with a ball bearing on the P.T.O.
end, assemble the crankshaft into the cylinder cover.
Place a drop of 680 Loctite in the crankshaft groove,
position supports under the cylinder cover, and using 7-13
an arbor press, press the shaft into the bearing until it
bottoms on the bearing.
3. Install the crankshaft and piston assembly into the
crankcase at the same time. Install a new bearing strip
on the crankpin or grease retain the loose needles if
applicable. If the piston has an arrow on top, the arrow
must point toward the exhaust port side of the engine.
If the piston does not have an arrow, the piston and
rod assembly must have the wrist pin retainer facing
the P.T.O. side of the engine. Position the crankshaft
crankpin at 90° to top dead center while sliding the
piston assembly over the crankshaft. Do not use force
positioning the assembly (diag. 7-14).
4. Install either a new crankcase cover "O" ring and 7-14
lightly oil if one was originally used, or apply Loctite #
gasket sealant eliminator (Tecumseh part # 510334)
to the crankcase surface to seal the crankcase cover.
Apply a continuous bead of Loctite (.062" [1.57 mm]
bead width) on the crankcase [Link] bead must
completely surround the tapped holes for the cover.
Loctite must not enter the crankcase (diag. 7-15).
5. Align the crankcase cover to the proper position using
the mounting bolts as a guide. Do not allow the cover "O" Ring
to rotate while assembling. Tighten the bolts to .062" (1.5 mm)
Bead of Loctite 7-15
achieve
70 - 100 inch pounds (7.9 Nm - 11.3 Nm) of torque.
6. Install the crankcase oil seal using seal protector (part
the seal must face toward the tool. Press the tool flush
to the crankcase.
7. Install crankcase cover oil seal using seal protector /
installer part # 670303 to protect the oil seal during
installation. The metal case of the seal must face
toward the tool. Press the tool flush to the cover.
8. Apply mineral spirits or kerosene to the crankpin
bearing and rotate the crankshaft to dissolve the wax
of a new needle bearing strip. Apply engine oil and
rotate the crankshaft to displace the grease used to
hold the needles in place on grease retained crankpin
bearings.
9. Install cylinder gasket (notched edge toward the
cylinder cover and the exhaust port side of cylinder),
or apply a .062" (1.57 mm) bead of Loctite # 515
to the cylinder crankcase surface if Loctite was
originally
used. The Loctite bead must completely surround the
cylinder bolt holes. Loctite must not be allowed to enter
the crankcase.
10. Use a piston and rod holder (dimensions are in Chapter 7-16
9 tool section) to prevent damage to the rod
31
Downloaded from [Link] manuals search engine
 are staggered and the cylinder is in the correct
position. Use fingers to compress the piston rings and
push the cylinder onto the piston. Do not rotate or
twist the
cylinder (diag. 7-16).
11. Install Torx bolts and alternately torque the bolts to
with studs instead of bolts: push the cylinder down to
a depth where the nuts can be started on the studs.
Finger tighten the nuts, use a wrench to snug, and
torque the nuts to 70 -100 inch pounds (7.9 Nm - 11.3
Nm) using a crowfoot on the torque wrench.
12. Install the exhaust gasket, muffler, spark arrestor if
applicable, bolts or muffler springs. Torque the muffler
bolts to 85 - 105 in. lbs (9.6 Nm - 11.8 Nm) of torque
if applicable. The longer ends of the springs
the bosses on the cylinder. Use heavy gauge wire (as
shown in the tool section) to stretch and hook the
muffler springs (diag. 7-17). Install the muffler heat
shield if applicable. Remove the engine holder.
13. Attach the blower housing base using the three screws
removed from the engine holder and torque the screws 7-17
to 30-40 inch pounds (3.3 Nm - 4.5 Nm).
14. On TC type I models, install the governor air vane
assembly into the blower housing base as shown.
Some models use a spring clip to hold the air vane in
position. Insert and tighten the speed adjusting lever
holddown screw to the blower housing base. Hook the
long end of the governor spring into the notch on the
neck of the air vane. The short end hooks into the
hole in the speed adjusting lever as shown (diag.
7-18).
15. Insert one end of the throttle link in the hole in the air
vane and the other end in the hole closest to the
and carburetor. Assemble gaskets correctly, do not
plug the pulse passage. Torque the bolts to 30-40
[Link]. (3.3 Nm - 4.5 Nm). On TC type II models,
torque the air vane to the carburetor throttle shaft
before installation. Hook the long end of the governor
spring in the hole in the air vane and the short end in
the hole in the speed control bracket. The spring
7-18
hooks from beneath both components. Use the
illustration (diag. 7-19) and the following spring
the air vane has more than one governor spring hole
and uses a colored spring with a square and round
end.

SPRING COLOR SPRING POSITION

Orange or Green 1
Pink, Red, OR Black 2 Spring Position 1

Spring Position 2
16. Install the flywheel key and flywheel. Install the
flywheel washer and nut, use a strapwrench (part#
670305) to
hold the flywheel, and torque the nut to 15-20 foot

7-19

32
Downloaded from [Link] manuals search engine
 17. Attach the ignition module, use the proper air gap
gauge between the flywheel magnets and the module
laminations (TC300 rotary mower applications and all
TC 200 models use air gap .0125" (.317 mm) part #
670291. All other TC 300 engine applications use a
030" (.762 mm) air gap or part # 670321). Torque the
module mounting screws to 30-40 inch pounds (3.3
Nm - 4.5 Nm). Remove the air gap gauge, rotate the
flywheel to assure it does not strike the ignition module.
Attach ignition grounding lead to the module terminal
(diag. 7-20).
NOTE: When using .030" (.762 mm) air gap gauge, it
is critical to push the module against the
flywheel
magnet before tightening the mounting screw.
18. Install the blower housing and rewind assembly.
Replace the debris guard if applicable.
19. Connect the fuel line at the carburetor, position
tank to the engine using the mounting spring. On TC
type II engines, hook the upper fuel tank mounting tab
over the blower housing stud and the carburetor studs.
Make sure the "O" ring is in position between the fuel All TC300 non-rotary mower use
tank and the carburetor. Tighten the retaining nuts, .030" (.762 mm) .0125" (.317 mm)
part number 670297
install filter(s), and attach the air cleaner cover. Air gap part number 670321
All TC200 an TC300 rotary
mower application
20. Reset the governor and / or speed control using the
procedure in Chapter 4 under "Service".
21. Install the spark plug and connect the high tension
lead.

33
Downloaded from [Link] manuals search engine
 CHAPTER 8
ENGINE SPECIFICATIONS AND
SEARS CRAFTSMAN CROSS-REFERENCE

TC TORQUE SPECIFICATIONS
The torque specifications listed in this chart are to be used for replacing components after disassembly, not for checking
an existing engine bolt torque. Checking a torque value on a new or used engine may be lower due to torque relaxation
that occurs on all engines from thermal expansion and contraction. However, sufficient clamping force exists and a re-
torque is not necessary.

Inch lbs. Ft. Lbs. Nm

Crankcase Cover to Crankcase 85 7 10
Cylinder Block to Crankcase 88 7 10
Spark Plug 230 19 26
Flywheel Nut 210 17.5 24
Solid State Mounting Bolts 35 3 4
Blower Housing Base to Crankcase 35 3 4.0
Starter Retainer Screw 35 3 4
Carburetor to Block 35 3 4
Air Vane to Carburetor 4 - .5
Starter Pawl to Flywheel 73 6 8.5
Muffler to Cylinder 95 8 11
A/C Cover TC Type II 4 - .5
Filter/Tank to Carburetor 23 2 2.6
Fuel Tank to Housing 23 2 2.6
Type II Speed Control to base 35 3 4

34
Downloaded from [Link] manuals search engine
 ENGINE SPECIFICATIONS

All Dimensions are in inches TC200 TC300

US Metric US Metric
mm mm
HP (Approx.) 1.6 1.19 Kw 2.0 1.49 Kw
Bore 1.4370 36.49 1.7495 44.43
1.4380 36.52 1.7505 44.46
Stroke 1.25 31.7 1.25 31.7
Displacement (in2) (cc) 2.0 32.78 cc 3.0 49.17 cc
Spark Plug Gap .030 .762 .030 .762
Ignition Module Air Gap .0125 .317 .030 .762
Note (A)
Piston Ring End Gap .004 .101 .005 .127
.014 .355 .015 .381
Piston Diameter 1.4330 36.398 1.7450 44.303
1.4345 36.436 1.7465 44.361
Piston Ring Groove Width .0485 1.231 .0485 1.2319
Top/Bottom .0495 1.257 .0495 1.2573
Piston Ring Width .046 1.168 .046 1.1684
.047 1.193 .047 1.1938
Crankpin Journal .5985 15.201 .5985 15.201
Diameter .5990 15.214 .5990 15.214
Note (B) Note (B)
Main Bearing Diameter .6248 15.869 .6248 15.869
P.T.O. Side .6253 15.882 .6253 15.882
Note (C) Note (C)
Main Bearing Diameter .4993 12.682 .4993 12.682
Flywheel .5003 12.702 .5003 12.707
Crankshaft .004 .1016 .004 .1016
End Play .012 .305 .012 .305
Note (D) Note (D)

35
Downloaded from [Link] manuals search engine
 SEARS CRAFTSMAN CROSS REFERENCE

143.681001 TC300 3010A

143.681021 TC300 3013A
143.941600 TC200 2103C
143.961670 TC200 2124D
143.961672 TC200 2103D
143.971670 TC200 2103E
143.971674 TC200 2124E
143.972070 TC300 3153E
143.982070 TC300 3176F
143.982072 TC300 3173F
143.992070 TC300 3187F

200.651001 TC200 2019C

200.681001 TC300 3010A
200.681021 TC300 3013A
200.681061 TC300 3021A
200.691001 TC300 3019A
200.691011 TC200 2040D
200.701011 TC200 2045E
200.701021 TC300 3027B
200.701031 TC300 3013B
200.701041 TCH300 3305
200.701051 TC300 3031B
200.711021 TCH300 3305A
200.711031 TC300 3013C
200.721001 TC200 2103
200.731031 TC300 3013E

36
Downloaded from [Link] manuals search engine
 CHAPTER 9 EDUCATIONAL MATERIALS AND TOOLS
AVAILABLE TECHNICIAN'S HANDBOOKS 695185
692508 Electrical Troubleshooting. This video training program will
Covers the diagnosis and repair of Tecumseh 2-cycle assist the small engine technician in the proper
engines. Except the TC Engine and TVS840. procedures for troubleshooting electrical systems on
692509 outdoor power
Covers the diagnosis and repair of the Tecumseh 4-cycle equipment.
light/medium frame engines. 695285
691462A An in-depth look at the 800 series transaxles. Detailing
the teardown and reassembly procedures for the 800, 801
Covers the diagnosis and repair of Tecumseh 4-cycle large and 820 transaxles.
frame engines.
691218 SPECIAL BOOKLETS
Covers the diagnosis and repair of Peerless® power train
components. INSTRUCTIONAL GUIDE
Assists in the use and understanding of the Tecumseh
694782 Master Parts Manual. Illustrates time saving features
Contains technical information for the repair of the TC incorporated into the manual. Explains new carburetor
series, 2-cycle engines. parts breakdown format.
694988
Contains diagnosis and technical information for the repair 4-CYCLE ENGINE FAILURE ANALYSIS
of TVS840, HSK/HXL845/850, 2-cycle engines. 695590
This booklet is designed as a tool for the average technician
695244A
to correctly assess the cause of failure.
Covers the diagnosis and repair of the OVRM/OVM/OHM/
OHV 4-cycle overhead valve engines. CARBURETOR TROUBLESHOOTING BOOKLET
695578 695907
Covers the diagnosis and repair of the Vector Series, This booklet is designed as a quick reference to carburetion
4-cycle engines. problems and related repair procedures.
AVAILABLE FOREIGN TECHNICIAN'S HANDBOOKS IGNITION SYSTEMS TROUBLESHOOTING BOOKLET
694903
694732 Spanish This booklet contains information on the identification,
This manual covers the following models: possible problems and related repair procedures of
VH80, VH100, HH80, HH100, HH120, OH120-180 Tecumseh Ignition Systems.
Model numbers are located on the engine shroud.
695555 Spanish SPECIAL TOOLS BOOKLET
Covers the diagnosis and repair of the Tecumseh 4-cycle 694862
light/medium frame engines. This booklet depicts all specialty tools offered by
695657 German Tecumseh
Covers the diagnosis and repair of the Tecumseh 4-cycle which can be used on 2 and 4 cycle engines and Peerless
light/medium frame engines. units.
695562 French
QUICK REFERENCE CHART BOOKLET
Covers the diagnosis and repair of the Tecumseh 4-cycle
This booklet contains the quick reference information
light/medium frame engines.
found on Tecumseh wall charts.
This booklet is designed to be used as a work bench quick
VIDEO PROGRAMS
reference guide when servicing Tecumseh engines and
695015
motion drive systems.
Carburetor Troubleshooting. Covers identification of
carburetors used on Tecumseh engines and how to
TESTER BOOKLETS
troubleshoot and repair them. VHS only. 694529
695059 Test procedures forTecumseh electrical components using
Understanding Tecumseh Ignition Systems. A basic Graham-Lee Tester 31-SM or 31-SMX-H.
program designed to give the small engine technician first 694530
hand knowledge of Tecumseh ignition systems so Test procedures for Tecumseh electrical components using
technician can understand the system and perform Merco-O-Tronic Tester 9800. (Tests are similar for 98, 98A
repairs to it. VHS only. and 79.)
695148
Teardown and reassembly of the 900 series transaxles.
This video will show a complete step-by-step procedure
for teardown and reassembly of the 900, 910 and 920
series transaxles.
37
Downloaded from [Link] manuals search engine
 TOOLS

FLYWHEEL PULLER 670299

STRAP WRENCH 670305

1/4"
HEAVY GAUGE WIRE HOOK FOR REMOVING (6.35 mm)
MUFFLER SPRINGS
12" LONG
(309 mm)

PISTON AND ROD HOLDER

A piece of 3/8" (9.5 mm) wood, 1-1/2" (38.1 mm) wide by
4" (101 mm) long with a slot 3/8" (9.5 mm) wide by 2" (50
mm) long cut out of the center will hold the piston and rod.

38
Downloaded from [Link] manuals search engine
 ENGINE HOLDER 670300
To assist in reassembly of the engine block and it's
components an Engine Holder, part number 670300, has
been developed. Attach to the crankcase of the engine
with the blower housing base screws and insert the other
end into a bench vise to hold crankcase while inserting
engine components.
670300

AIR GAP GAUGE 670297 AIR GAP GAUGE .0125 (.317 mm)
Used on all TC200 and all TC300 engines used on rotary PART NO. 670297
mower applications.

AIR GAP GAUGE 670321 AIR GAP GAUGE .030 (.762 mm)

Used on TC300 non-rotary mower engine applications. PART NO. 670321

SEAL PROTECTOR AND INSTALLER 670303

Used on the PTO oil seal.

670303

BEARING INSTALLER 670304A

Used to install the PTO bearing.

670304A

SEAL PROTECTOR AND INSTALLER 670301

Used on the flywheel end oil seal.

670301

BEARING INSTALLER 670302

Used to install the bearing in the flywheel end.

670302

39
Downloaded from [Link] manuals search engine
 TORX DRIVERS
Torx 8 670334
Torx 10 670333
Torx 15 670323
Torx 20 670324
Torx 25 670319
Torx 30 670320

SPECIAL PART 510334

334
Loctite Gasket Sealant Eliminator No. 515 will be sold by NO . 510
ART
Tecumseh under the part number 510334.
MS EH P
TECU

VIBRATION TACHOMETER 670156

METERING LEVER GAGE 670325

Used to set carburetor metering lever.

40
Downloaded from [Link] manuals search engine