AHU Air Handling Unit Fundamentals
Objectives Review primary components of an AHU Understand the basic progression and advantages of advanced AHU control Understand the basic control sequences Review key operating concepts
HVAC System in a Building
HVAC Air Systems
HVAC air systems are made up of:
AHU - Air handling units Dampers Coils and Valves Fans Distribution ducts and terminal boxes Pumps and Plumbing Control devices and control loops Unitary equipment: fan coils, perimeter radiation, unit ventilators, unit heaters, etc.
AHU - Components & Terminology
EA
RA
Return From Space
OA Filter Cooling Coil Heating
DA
AHU components
Supply fan Mixed Air sensor Heating coil & valve Cooling coil & valve
Discharge air sensor
Mixed air dampers section
Discharge air Duct
Return Air sensor
Return air Duct
AHU components
Types of Air Handlers
Air Handling Units Mixed Air
Types of Air Handlers
Air Handling Units Mixed Air
A Single Duct AHU variation
The exhaust air damper is not in this air handler; the building air is exhausted elsewhere, but the basic mixed air and other functions are unchanged.
Air Handler Components
The fan section with access door open.
Air Handler Components
The filter section.
Notice the cross stacking of the filters to increase surface area.
Air Handler Components
Temperature Sensor:
Temperature sensors are used for measurement of temperatur of a Room, Air Duct, Hot /Cold Water, Outside Air etc. Models are available with PT1000, NTC20K, BALCO500 sensing elements.
LF20 : AIR DUCT TEMP. SENSOR (NTC 20k)
T7412 : ROOM TEMP. SENSOR (PT1000/NTC 20k)
T7413A : IMMERSION TEMP. SENSOR (PT1000)
Air Handler Components
Relative Humidity Sensor:
Relative Humidity sensors are used for measurement of Relative humidity of a Room, Air Duct, Outside Air etc. Sensor Type : Capacitance Combined Relative Humidity and Temperature Sensors are available with PT1000, NTC20K, BALCO500 sensing elements.
H7015 : DUCT RELATIVE HUMIDITY SENSOR
H7012 : ROOM RELATIVE HUMIDITY SENSOR
Air Handler Components
Differential Pressure Switch:
Differential Pressure switches are used for monitoring of Filter, Fan, Pump, Fire Damper, Water Flow, Air Flow Status of air handling systems.
DPS1000 : AIR DIFFERENTIAL PRESSURE SWITCH
TDIAP SERIS : AIR FLOW SWITCH
Air Handler Components
Differential Pressure Sensors/Transmitter:
Used for measuring diff. Pressure, positive pressure and vacuum.
DPT1000 : AIR DIFF. PRESSURE TRANSMITTER
ST 3000 Pressure Transmitter
Air Handler Components
Coils :
Heating Coils Cooling Coils Coil Construction Copper with Aluminium fins, 13 Fins /inch Number of Rows, I.e 4/6/8 depending on the latent heat load & Bypass Factor.
Air Handler Components
The coil section of a AHU.
Note: There may be a wide variety of actual configurations
Air Handler Components
Valves & Actuators Valve Types 2 Way or 3 Way Actuator Types Motorised Magnetic Pneumatic Operation On - Off,Floating, Modulating
Air Handler Components
Heat Recovery :
A heat-recovery system is often used in buildings where a significant quantity of outdoor air is used. Several types of heat-recovery systems are available Heat pumps Runaround systems Rotary heat exchangers Heat pipes.
Heat Wheel
Runaround systems
Air Handler Components
Heat Recovery : Heat Wheel
Typical AHU Damper Sequences
Manually adjustable quantity of outdoor air: Similar to Fixed, but
with a user adjustment device for adjusting damper setting from 0% to 100% outdoor air. No automatic control. W/WO exhaust or return air ducts.
Typical AHU Damper Sequences
Mixed Air Dampers: Mixes OA and RA to maintain a mixed air setpoint via direct acting controller. Modulates 0% to 100%. Provides ventilation for IAQ. Provides free cooling. Provides proper temperature for H/C coil operation. OA and EA dampers close via relay with fan off. RA damper opens via relay with fan off.
Typical AHU Damper Sequences
Example of operation:
Setpoint = 55 deg. MAT = 55 deg.
Proportional Controller output = 50% Fan = On Dampers:
OA = 50% RA = 50%
Typical AHU Damper Sequences
Example of operation on temperature rise:
Setpoint = 55 deg. MAT = 57.5 deg.
Controller output = 75% Fan = On Dampers:
OA = 75% RA = 25%
More outdoor air!
Typical AHU Damper Sequences
Example of operation on temperature fall:
Setpoint = 55 deg. MAT = 50 deg. Controller output = 0% Fan = On OA = 0% RA = 100%
Dampers:
No outdoor air; no fresh air in the building!
Mixed Air Dampers with a Minimum Position Setting
Maintains a minimum outdoor damper position via a minimum adjustment device when building is occupied. (fan on) Meets IAQ code requirements.
Typical AHU Damper Sequences - Mixed Air
Example of operation on temperature fall:
Setpoint = 55 deg. MAT = 50 deg. Controller output = 0%
Min. Position Setpoint = 25% Fan = On Dampers:
OA = 25% RA = 75%
25%
75%
Even though the Mixed Air controller is sending a control signal to completely close OA dampers, the minimum position controller or logic is maintaining setpoint. Fresh air is maintained in the building!
25%
Typical AHU Damper Sequences
Economizer Override . of Outdoor Air:
Requires an additional reverse acting controller in the outdoor air. Brings OA damper to minimum when outdoor air temperature is high. Provides for economical operation of the cooling coil.
50%
50%
Typical AHU Damper Sequences
Example of economizer operation with low outdoor temp.
MA StPt = 55 deg MA temp = 55 deg MA controller out = 50% OA StPt = 70 deg OA temp = 67 deg OA controller out = 100%
50%
50%
Min. Pos. StPt = 25%
OA damper = 50%: MA controller is in control of the OA damper due to OAT acceptable for efficient use of mechanical cooling.
Typical AHU Damper Sequences
Economizer Override with outdoor temperature high:
MA StPt = 55 deg MA temp = 55 deg MA controller out = 50% OA StPt = 70 deg OA temp = 74 deg OA controller out = 0% Min. Pos. StPt = 25%
75%
OA damper = 25%:
OA controller is in control of the OA damper due to OAT unacceptable for efficient mechanical cooling.
25%
Typical AHU Damper Sequences
Enthalpy controlled override of Mixed Air control:
Total heat (enthalpy) of outdoor air is compared to total heat of return air to decide which is more economical for efficient cooling coil operation.
Typical AHU Damper Sequences
Example of operation with OA enthalpy lower:
MA StPt = 55 deg
MA temp = 55 deg MA controller out = 50%
OA humidity = 35% OA temp = 60 deg RA humidity = 39% RA temp = 71 deg Outdoor air enthalpy is lower than return air enthalpy, so relay passes MA controller signal. Min. Pos. StPt = 25% OA damper = 50%
Practical Example
100%Outside Air AHU :
OA AHU Seq
Practical Example
Mixed Air AHU :
Seq of Oper AHU
Plant
Chiller Plant
Chiller Plant
Chiller Plant systems are made up of:
Chiller/Condenser Unit Chilled Water Pumps Condenser Water Pumps Cooling Towers Makeup Water Tank A/C Expansion Water Tank
TRANE Chiller
Chiller Plant
Chiller Plant Concept :
Typical Cooling Tower
Typical Chiller Plant
Example Chiller Plant
Seq of Oper CHILLER
Example Chiller Plant (THL New Building)
Example Chiller Plant
Boiler Plant
Boiler Plant systems are made up of:
Boiler Units Primary Pumps Secondary Pumps
Typical Firetube Boiler
Boiler Plant
Boiler Plant Example
Seq of Oper BOILER
Boiler Plant Example
Boiler Plant Example
