Scribd
Upload
81 views4 pages

East West University: Department of Electrical and Electronic Engineering

This document summarizes an electrical engineering student's laboratory experiment on basic circuit variables and elements. The student measured the voltages, currents, and resistances in a series and parallel circuit. For the series circuit, the calculated and measured values matched. For the parallel circuit as well, the calculated resistances matched the measured values. The student concluded they learned how current and voltage behave in series and parallel circuits and how to make measurements using an ammeter and voltmeter.

Uploaded by

Md Asif Hossain
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
81 views4 pages

East West University: Department of Electrical and Electronic Engineering

This document summarizes an electrical engineering student's laboratory experiment on basic circuit variables and elements. The student measured the voltages, currents, and resistances in a series and parallel circuit. For the series circuit, the calculated and measured values matched. For the parallel circuit as well, the calculated resistances matched the measured values. The student concluded they learned how current and voltage behave in series and parallel circuits and how to make measurements using an ammeter and voltmeter.

Uploaded by

Md Asif Hossain
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd

EAST WEST UNIVERSITY

DEPARTMENT OF ELECTRICAL AND ELECTRONIC ENGINEERING

Course No Section No Group No

: EEE 101 : 04 : 03

Experiment No

: 01

Experiment Name : Introduction to circuit variables and elements

Date of Performance : 26.01.2011 Date of Submission : 02.02.2011

Students Name : [Link] HOSSAIN Students ID : 2011-1-80-081

Introduction to circuit variables and elements


OBJECTIVE :
Current and voltage are the two basic variables in an electric circuit, they are not sufficient by themselves. Power is defined as the rate of energy dissipation. An element is the basic building block of a circuit. An electric circuit is simply an interconnection of the elements. Circuit analysis is the process of determining voltage across the elements of the circuit.

CIRCUIT DIAGRAMS :

(a)

(b)

Figure : Diagrams for a series circuit (a) and a parallel circuit (b). Experimental Data :
Table 1 : Measured values of resistors.

R1 (Ohm) 46

R2 (Ohm) 98

R3 (Ohm) 98

R4 (Ohm) 219

Table 2 : Measured voltages and currents for the circuit of figure(a).

Vs (V) 2.5

VR1 (V) 0.782

VR2 (V) 1.66

I (mA) 17

Table 3 : Measured voltages and currents for the circuit of figure(b).

Vs (V) 2.5

V (V) 2.5

I1 (mA) 25.5

I2 (mA) 11.4

Answer to Report Questions : 1 . Submitted the experimental datasheet. 2 . RS=R1+R2


=46+98 =144 VS=IRS I = VS/RS = 2.5/144 = 0.017 V1 = IR1 = 0.017 X 46 = 0.782 V2 = IR2 = 0.017 X 98 = 1.66

For circuit (b) We know, 1/RP = 1/R3 + 1/R4 = 1/98 + 1/219 RP = 67.72 I1 = VS/R3 = 2.5/98 = 25.5 mA I2 = VS/R4 = 2.5/219 = 11.4 mA

3 . Compare the calculated values with the measured values : Calculated Values V1 = 0.799 V V2 = 1.70 V V = 2.5 V I = 17 mA I1 = 25 mA I2 = 11.4 mA Measured Values V1 = 0.782 V2 = 1.66 V = 2.5 I = 17 mA I1 = 25.5 mA I1 = 11.4 mA

There are no differences with the measured and calculated values. So the measured and the calculated values are equal.

4 . R1 = V1/I = 0.798/0.017 = 46.94 (Ohm)


R2 = V2/I = 1.66/0.017 = 97.64 (Ohm) R3 = Vs/I1 = 2.5/0.025 = 98 (Ohm) R4 = VS/I2 = 2.5/0.0114 = 219 (Ohm) Comments : The measured and the calculated value R1 and R2 are equal. Also R3 and R4 are equal.

5 . The ammeter in the circuit with series and the voltmeter in the circuit with parallel. The
ammeter and voltmeter has two scales, one is 100 to 1000 and another is 30 to 300. If we take reading 100 scale then we divided 1000/100 = 10 and if we take reading 30 scale then we divided 300/30 = 3.

Conclusion :
We see that there are two circuits. One circuit is connected in series and other is connected in parallel. We can learn how to flow current and voltage in the circuit and we also learn to take reading with ammeter and voltmeter. We are able to take value with resistance. We apply in the experiment ohms law to calculate.

You might also like