CC 71
Mixing oil
Air-entraining agent for mortar and concrete
CHARACTERISTICS
segregation-inhibiting
plasticizing
easy to use
reduces the amount of mixing water
needed
chloride free
SCOPE OF USE
For increasing the frost and deicing salt resistance of
concrete, e.g. on runways, concrete roads, concrete
products etc.
For improving the workability of plasters, screeds,
concrete floors etc.
For increasing the content of air voids and improving
the water retention value.
For improving the resistance properties of screeds and
concrete floors.
APPLICATION
Add the appropriate amount of CC 71 to the mixing
water and stir briefly.
Use this mixture to produce the concrete or mortar
mixture. Allow for the reduced water demand.
Test the product for suitability before use. Observe the
mixing times specified by DIN 1045.
When using CC 71 in combination with CC 92 or
CC 93, only add 50 % of the applicable quantity of
CC 71.
PLEASE NOTE
Use CC 71 only at temperatures of +5 C to +35 C.
If the applicable amount of CC 71 is exceeded,
both compressive and bending tensile strength will
be reduced.
CC 71 is irritating. Therefore protect skin and eyes.
C
E
R
E
S
I
T
C
_
C
C
7
1
_
T
M
_
1
1
_
0
7
0
4
o
1
If contact occurs, wash off and rinse copiously with
water. In case of contact with the eyes obtain medical
advice.
Remove contaminated clothing.
Please refer in particular to DIN 1045, DIN 18 550
and DIN 18 560.
Should you need support or advice, please consult
our advisory service for architects and craftsmen on
the hotline numbers
Phone: +49 211 797 0
Fax: +49 211 798 2148
TECHNICAL DATA
Base: Synthetic and natural air-entrai-
ning agents in alkaline solution
GISCODE BZM 2
Density: approx. 1.10 kg/l
Air content in
- fresh concrete: 3 5 %
(DIN 18 555)
- fresh mortar: approx. 13 %
(DIN 18 555)
Reduction of
mixing water needed: approx. 10 %
Mixing ratio: For mortar:
approx. 100 ml/50 kg of binder
(750 800 ml/200 l of water)
For concrete:
approx. 25 50 ml/50 kg
of cement
Storage: shelf life approx. 12 months in a
frost-free but cool place
Packaging: 6 kg, 12 kg and 35 kg tin cans
C
E
R
E
S
I
T
C
_
C
C
7
1
_
T
M
_
1
1
_
0
7
0
4
o
2
Build on professional solutions.
Henkel AG & Co. KGaA Bautechnik
Henkelstrae 67 D-40589 Dsseldorf
Telefon +49 (0) 211/797-0 Telefax +49 (0) 211/7986667
Internet: [Link] E-Mail: [Link]@[Link]
The information contained herein, particularly recommendations for the handling and use of our products, is based on our professional experience.
As materials and conditions may vary with each intended application, and thus are beyond our sphere of influence, we strongly recommend that
in each case sufficient tests are conducted to check the suitability of our products for their intended use. Legal liability cannot be accepted on the
basis of the contents of this data sheet or any verbal advice given, unless there is a case of wilful misconduct or gross negligence on our part.
This technical data sheet supersedes all previous editions relevant to this product.
Apart from the information given here it is also important to observe the relevant guidelines and regulations of various organisations and trade
associations as well as the respective standards of the German Standards Institute (DIN). The aforementioned characteristics are based on practical
experience and applied testing. Warranted properties and possible uses which go beyond those warranted in this information sheet require our
written confirmation. All data given was obtained at an ambient and material temperature of +23 C and 50 % relative air humidity unless specified
otherwise. Please note that under other climatic conditions hardening can be accelerated or delayed.
