Scribd
Upload
85 views1 page

Tds-Bi5 0ga

This document provides information on BI5.0GA polypropylene material characteristics for injection molding applications. It has medium flow, high impact strength, good processability, creep resistance at high temperatures, and FDA compliance. Recommended uses include furniture, housewares, paint pails, motorcycle parts, and electrical applications. Test data is provided for properties like melt flow rate, density, tensile strength, elongation, flexural modulus, impact strength, hardness, and melting temperature. Recommended injection molding conditions are listed.

Uploaded by

FalecyaRedina
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
85 views1 page

Tds-Bi5 0ga

This document provides information on BI5.0GA polypropylene material characteristics for injection molding applications. It has medium flow, high impact strength, good processability, creep resistance at high temperatures, and FDA compliance. Recommended uses include furniture, housewares, paint pails, motorcycle parts, and electrical applications. Test data is provided for properties like melt flow rate, density, tensile strength, elongation, flexural modulus, impact strength, hardness, and melting temperature. Recommended injection molding conditions are listed.

Uploaded by

FalecyaRedina
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd

BI5.

0GA
POLYPROPYLENE
CHARACTERISTICS :
- Medium Flow
- High Impact Strength
- Good Processability
- Creep Resistance at Elevated Temperature
- Compliance with FDA Regulation 21CFR177.1520
APPLICATIONS :
Furnitures, Housewares, Paint Pails , Motorcycle
Parts, Electricals and General Purpose of Injection
Molding Applications
Physical Properties Test Method* Unit
Melt Flow Rate
Density
Tensile Strength @Yield
Elongation @Yield
Flexural Modulus (1% secant)
Notched Izod Impact Strength
Hardness, Rockwell
Deflection Temperature
Vicat Softening Temperature
Melting Temperature
( 230 C / 2.16 kg )
@ 50 mm / min
@ 1.3 mm / min
@ 23 C
@ 0.455 MPa (4.64 kg/cm )
DSC, 10 C/min, 2 heat)
ASTM D 1238
ASTM D 792
ASTM D 638
ASTM D 638
ASTM D 790A
ASTM D 256
ASTM D 785
ASTM D 648
ASTM D 1525B
ASTM D 3418
g/10 min
g/cm
MPa
%
MPa
J/m
R Scale
C
C
C
o
3
2
o
o
o
o nd
Value
*) Polypropylene tested per ASTM D 4101 Conversion : 1 MPa = 10.2 kgf/cm
2
1 kJ/m = 0.01 [Link]/mm
2 2
Recommended Processing Conditions :
This material complies with recommendations and statutory regulations in the USA, Japan and most European
countries regarding packaging materials intended to come in contact with foodstuff.
The nominal properties reported herein are typical on the product of CAP
but do not reflect normal testing variance and therefore should not to be
construed as specifications.
CAP reserves the right to make any improvement or amendments to the
composition of any grade or product without alteration to the product code.
Thi s document reports accurate and rel i abl e i nformati on to the best of our
knowledge on the products manufactured by CAP. Since CAP can not anticipate or
control the conditions under which this information and its product may be used,
each user should review the information in the specific context of the intended
appl i cat i on. CAP wi l l not be r esponsi bl e f or damages of any nat ur e
r e s u l t i n g f r o m t h e u s e o f o r r e l i a n c e u p o n t h e i n f o r ma t i o n .
This technical datasheet is effective as from January 2013 and supersedes all previously published data.
Injection Molding
5
0.9
26
12
1032
170
77
100
148
163
Wisma Barito Pacific Tower A, 7 Floor
Jl. Let. Jend. S. Parman Kav. 62-63
Jakarta 11410, Indonesia
T +6221-530 7950, F +6221-530 8930
[Link]
th
PT. Chandra Asri Petrochemical Tbk
Injection Temperature .. 220 - 240 deg. C
Mol d Temperature .. 20 - 40 deg. C

You might also like