Scribd
Upload
416 views6 pages

Pneumatic Sequential Control Report

This document is a lab report submitted by three students at Politeknik Sultan Azlan Shah for their Pneumatics and Hydraulics class. It details an experiment on the sequential control of two double-acting cylinders without overlapping signals. The objectives were to apply safety rules, design the pneumatic circuit, and differentiate between sequential control with and without overlapping signals. The report describes the equipment used, safety procedures, operational steps of the circuit, assembly and testing procedures, and includes a reference.

Uploaded by

Adid Punya
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
416 views6 pages

Pneumatic Sequential Control Report

This document is a lab report submitted by three students at Politeknik Sultan Azlan Shah for their Pneumatics and Hydraulics class. It details an experiment on the sequential control of two double-acting cylinders without overlapping signals. The objectives were to apply safety rules, design the pneumatic circuit, and differentiate between sequential control with and without overlapping signals. The report describes the equipment used, safety procedures, operational steps of the circuit, assembly and testing procedures, and includes a reference.

Uploaded by

Adid Punya
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd

POLITEKNIK SULTAN AZLAN SHAH

PNUEMATIC AND HYDROLIC


REPORT LAB 1
SUBMISSION DATE : 7 OCTOBER 2014
LECTURE NAME : PUAN MAI NOOR ASIAH BINTI TAN ZALILAH
NAME

NO MATRIK

EDY BIN MOHD

15BAD11F2022

MUHAMMAD MUADDID BIN MANSOR

15BAD11F2008

MUHAMMAD ZAFRIE

15BAD11F2037

TOPIC
SEQUENTIAL CONTROL OF 2 DOUBLE ACTING CYLINDER WITHOUT OVERLAPPING SIGNALS

OBJECTIVES
At the end of the session the students will be able to :
I.
II.
III.

Apply safety rules in the laboratory


Design pneumatic circuit using a sequential control of two double acting cylinders
without overlapping signals and with overlapping signals
Differentiate between sequential control without overlapping signals and with
overlapping signals

SEQUENTIAL CONTROL
Many pneumatic systems and machines are designed to perform a range task in a certain
order sequence. This usually involves the use of two or more cylinders working together to
complete the task. The movement of these cylinders are coordinated as per the required
sequence. This sequencing is carried out by actuation of appropriate final control valves like
directional control valves. The position of the cylinders is sensed by sensors like limit
switches, roller or cam operated valves.

EQUIPMENT
I.

Double acting cylinders

II.

5/2 ways directional control valve, impulse valve

III.

One way flow control valve

IV.

3/2 directional control valve with push button

IV.

3/2 directional control valve with roller

SAFETY
Build your designs and verify your operation. Make sure that the pressure is 4 bars and is
connected correctly. Double check your connections before switching the compressor on.

OPERATION
I.
II.
III.
IV.
V.
VI.

The workpiece coming in on the right roller conveyor should be elevated and sent in
a new direction.
After actuating the start button the piston of cylinder A raises the workpiece to the
height of the second roller conveyor with its elevating platform.
Cylinder A remains in this position until cylinder B has pushed the workpiece from
the elevating platform onto the upper roller conveyor.
When cylinder A has securely pushed all the workpiece onto the upper roller
conveyor, cylinder A moves down again.
Only when cylinder A has retracted into its lower end position does cylinder B also
retract.
The working speed of both cylinders is infinitely adjustable in both directions.

PROCEDURES
Simulation

Assembling the circuit


1.
2.
3.
4.
5.
6.
7.
8.
9.

Prepare the components according to the above components list.


Mount all components according to the pneumatic circuit.
Connect pneumatic tubes according to the pneumatic circuit.
Check that all parts are connected properly and firmly with each other.
Switch on the service unit and start the circuit.
Check the operation of the circuit for any malfunctions.
Turn of the sevice unit.
Dismantle and tidy up.
Write dowm your observation.

RESULT

REFERENCES

Book

[Link] (2002). Practice for Professionals Pneumatic Trainers Manual. Germany: Bosch
Rexroth

You might also like