Hibond Flooring System
3.3.5 HIBOND COMPOSITE SLAB LOAD SPAN TABLES
Superimposed loads (GSDL + Q) are presented for slab thicknesses between 110mm and 200mm
and over a range of spans between 2.0m and 6.0m for single spans. For continuous design, negative
reinforcement requirements are presented for double or end spans and internal spans, with an
extended range of spans to 7.0m for the latter.
The following Notes apply to the composite slab load span tables in this Section.
1. Span types
Lss is the clear single span between permanent supports plus 100mm.
L is the double/end or internal span measured centre to centre between permanent supports.
2. The design superimposed load combination is GSDL + Q and must not be greater than the
superimposed loads given in the tables.
3. a) Medium term superimposed loads are based on 2/3 short term and 1/3 long term (i.e. modular
ratio = 10) and apply to buildings of normal usage.
b) Long term superimposed loads are based on all loads being long term (i.e. modular ratio = 18)
and apply to storage loads and loads which are permanent in nature.
4. Deflection limits incorporated into these tables are as follows:
a) L/350 or 20mm maximum due to superimposed load (GSDL + Q).
b) L/250 maximum due to superimposed load plus prop removal (G + GSDL + Q).
The designer shall be satisfied that these limits are adequate for the application considered,
otherwise additional deflection checks must be made.
5. Propping requirements depend on the Hibond slab thickness and span configuration as formwork.
Refer to Section [Link] Hibond Formwork Tables to determine formwork span capabilities.
6. The double or end span and internal span tables allow for 10% moment redistribution where
negative bending governs (typically thinner slabs on end spans), bounded by the shear bond value
where this governs.
7. Some values shown in the double or end span tables are less than corresponding values given in
the single span tables. This situation arises as,
a) Negative bending capacity has been limited to avoid compression failure of the concrete in
compression at the internal support.
b) Shear bond is proportional to vertical shear which is higher for a double span than a single
span. Also the shear bond span for an end span must be taken as the full span length using
BS5950 Part 4 (when normally the span between points of contraflexure would be used).
Continued on next page
October 2006
Hibond Flooring System
3.3.5 HIBOND COMPOSITE SLAB LOAD SPAN TABLES continued
8. Use of the double or end span tables and internal span tables assumes,
All spans have the same slab thickness.
The end span is within plus 5% or minus 10% of the internal span and that the end and
internal spans are both designed using the appropriate load span table.
Double spans are within 10% of each other and the slab design is based on the largest span.
Internal spans are within 10% of each other and the slab design is based on the largest internal
span.
Any variations to the above configurations require specific design.
9. Example: For a 0.75mm Hibond slab of 130mm overall slab thickness on a double span of
3800mm we have the following:
4.3 H12@200
where:
4.3
= Superimposed load kPa
H12@200 = H12 negative reinforcing (saddle bars) placed at 200mm centres
to achieve the superimposed load.
10. Steel areas in the double or end and internal span tables are calculated based on H12 reinforcing
bars (12mm diameter grade 500 to AS/NZS 4671) placed at 25mm top cover (A1 exposure
classification NZS 3101). Areas for other bar types, covers and sizes require specific design.
11. Negative reinforcement must be placed on top of the mesh parallel with the Hibond ribs at
spacings indicated in the tables for the span and slab thickness considered.
12. Negative reinforcement must extend at least 0.25 of the largest span plus 450mm each side of
the centre line of the support.
13. The same negative reinforcing is required for both propped and unpropped construction.
Continued on next page
October 2006
Hibond Flooring System
3.3.5 HIBOND COMPOSITE SLAB LOAD SPAN TABLES continued
14. Vibration limits expressed as maximum spans in the tables refer to:
Commercial offices, open plan with few small partitions (damping ratio = 0.025)
Residences with many full height partitions (damping ratio = 0.05)
Specific design is required for other floor uses. Refer Section 3.3.8 Floor Vibration.
15. For intermediate values, linear interpolation is permitted.
Typical Composite Slab Span Configurations
Negative
reinforcement
Hibond sheet
This configuration requires nominal
continuity reinforcement to be placed
over the supports as described for
a minor degree of crack control for
Mesh Reinforcement in Section 3.3.2.
October 2006
Hibond Flooring System
3.3.5 HIBOND COMPOSITE SLAB LOAD SPAN TABLES continued
0.75mm HIBOND SINGLE SPANS
Medium term superimposed loads (kPa)
Lss
mm
2000
2200
2400
2600
2800
3000
3200
3400
3600
3800
4000
4200
4400
4600
4800
5000
5200
5400
5600
5800
6000
110
120
130
16.2
13.3
11.2
9.5
8.2
7.1
6.2
5.5
4.9
4.4
4.0
3.6
2.9
2.3
1.8
19.6
16.1
13.5
11.4
9.8
8.5
7.4
6.5
5.8
5.2
4.7
4.2
3.8
3.3
2.6
2.0
1.6
21.0
17.2
14.3
12.1
10.4
9.0
7.8
6.9
6.1
5.4
4.8
4.3
3.9
3.6
3.2
2.9
2.3
1.8
140
19.3
16.0
13.5
11.5
9.9
8.6
7.5
6.6
5.9
5.3
4.7
4.2
3.8
3.5
3.2
2.9
2.6
2.1
1.6
Slab thickness (Ds) mm
150
160
170
180
190
200
21.4
17.9
15.1
12.9
11.1
9.6
8.4
7.4
6.5
5.8
5.1
4.6
4.1
3.7
3.3
3.0
2.7
2.5
2.2
19.4
16.3
13.9
11.9
10.3
8.9
7.8
6.9
6.1
5.4
4.8
4.3
3.8
3.4
3.1
2.7
2.5
2.2
20.8
17.5
14.8
12.7
10.9
9.5
8.3
7.2
6.3
5.6
5.0
4.4
3.9
3.5
3.1
2.8
2.5
2.2
18.8
15.9
13.6
11.6
10.1
8.7
7.6
6.7
5.8
5.1
4.5
4.0
3.6
3.1
2.8
2.5
2.2
Slab thickness (Ds) mm
150
160
170
180
190
200
19.4
16.3
13.9
11.9
10.3
8.9
7.8
6.9
6.1
5.4
4.8
4.3
3.8
3.4
3.1
2.7
2.5
2.0
20.8
17.5
14.8
12.7
10.9
9.5
8.3
7.2
6.3
5.6
5.0
4.4
3.9
3.5
3.1
2.8
2.5
2.2
18.8
15.9
13.6
11.6
10.1
8.7
7.6
6.7
5.8
5.1
4.5
4.0
3.6
3.1
2.8
2.5
2.2
21.4
17.7
14.9
12.7
10.9
9.4
8.2
7.2
6.4
5.7
5.1
4.5
4.1
3.7
3.3
3.0
2.8
2.5
2.3
1.8
19.5
16.4
13.9
11.9
10.3
8.9
7.8
6.9
6.1
5.4
4.8
4.3
3.9
3.5
3.2
2.9
2.6
2.4
2.2
0.75mm HIBOND SINGLE SPANS
Long term superimposed loads (kPa)
Lss
mm
2000
2200
2400
2600
2800
3000
3200
3400
3600
3800
4000
4200
4400
4600
4800
5000
5200
5400
5600
5800
6000
October 2006
110
120
130
16.2
13.3
11.2
9.5
8.2
7.1
6.2
5.4
4.3
3.4
2.6
2.0
19.6
16.1
13.5
11.4
9.8
8.5
7.4
6.5
5.7
4.6
3.6
2.8
2.2
1.6
21.0
17.2
14.3
12.1
10.4
9.0
7.8
6.9
6.1
5.4
4.8
3.9
3.1
2.4
1.8
140
19.3
16.0
13.5
11.5
9.9
8.6
7.5
6.6
5.9
5.3
4.7
4.2
3.3
2.6
2.0
21.4
17.7
14.9
12.7
10.9
9.4
8.2
7.2
6.4
5.7
5.1
4.5
4.1
3.5
2.8
2.1
1.6
19.5
16.4
13.9
11.9
10.3
8.9
7.8
6.9
6.1
5.4
4.8
4.3
3.9
3.5
2.9
2.3
1.7
21.4
17.9
15.1
12.9
11.1
9.6
8.4
7.4
6.5
5.8
5.1
4.6
4.1
3.7
3.3
3.0
2.4
1.8
Hibond Flooring System
3.3.5 HIBOND COMPOSITE SLAB LOAD SPAN TABLES continued
0.75mm HIBOND DOUBLE AND END SPANS
Medium and Long Term Superimposed Loads (kPa) and Negative Reinforcement (mm2/m width)
Slab Thickness (Ds) mm
L (mm)
110
120
130
140
150
160
170
180
190
2000
12.9 H12@300
15.7 H12@250
16.8 H12@300
18.8 H12@250
21.0 H12@300
2200
10.7 H12@250
12.9 H12@250
13.8 H12@250
15.4 H12@250
17.1 H12@300
18.9 H12@250
20.8 H12@250
2400
8.9 H12@250
10.8 H12@250
11.5 H12@250
2600
7.6 H12@250
9.1 H12@250
9.7 H12@250
12.8 H12@250
14.2 H12@250
15.6 H12@250
10.8 H12@250
11.9 H12@250
13.1 H12@250
2800
6.4 H12@250
7.8 H12@250
8.3 H12@250
9.2 H12@250
10.1 H12@250
3000
5.3 H12@250
6.8 H12@200
7.2 H12@250
7.9 H12@250
3200
4.5 H12@250
5.9 H12@200
6.2 H12@250
3400
3.8 H12@250
5.0 H12@200
3600
3.2 H12@250
3800
17.1 H12@250
18.6 H12@250
20.1 H12@250
14.3 H12@250
15.5 H12@250
16.7 H12@250
17.9 H12@250
11.1 H12@250
12.1 H12@250
13.0 H12@250
14.0 H12@250
15.0 H12@250
8.7 H12@250
9.5 H12@250
10.3 H12@250
11.1 H12@250
11.9 H12@250
12.7 H12@250
6.9 H12@250
7.5 H12@250
8.2 H12@250
8.9 H12@250
9.5 H12@250
10.2 H12@250
10.8 H12@250
5.5 H12@200
6.0 H12@250
6.6 H12@250
7.1 H12@250
7.7 H12@250
8.2 H12@250
8.7 H12@250
9.3 H12@250
4.3 H12@200
4.9 H12@200
5.3 H12@250
5.8 H12@250
6.3 H12@250
6.7 H12@250
7.2 H12@250
7.6 H12@250
8.0 H12@250
2.7 H12@250
3.6 H12@200
4.3 H12@200
4.7 H12@200
5.1 H12@200
5.5 H12@250
5.9 H12@250
6.3 H12@250
6.6 H12@250
7.0 H12@250
4000
2.2 H12@250
3.1 H12@200
3.9 H12@200
4.2 H12@200
4.5 H12@200
4.9 H12@200
5.2 H12@250
5.5 H12@250
5.8 H12@250
6.1 H12@250
4200
1.9 H12@250
2.6 H12@200
3.5 H12@200
3.8 H12@200
4.0 H12@200
4.3 H12@200
4.6 H12@200
4.9 H12@250
5.1 H12@250
5.3 H12@250
4400
2.2 H12@200
3.0 H12@200
3.4 H12@200
3.6 H12@200
3.9 H12@200
4.1 H12@200
4.3 H12@200
4.5 H12@250
4.7 H12@250
4600
1.8 H12@200
2.5 H12@200
3.1 H12@200
3.3 H12@200
3.5 H12@200
3.7 H12@200
3.8 H12@200
4.0 H12@200
4.1 H12@250
4800
2.1 H12@200
2.8 H12@200
2.9 H12@200
3.1 H12@200
3.3 H12@200
3.4 H12@200
3.5 H12@200
3.6 H12@200
5000
1.8 H12@200
2.4 H12@200
2.7 H12@150
2.8 H12@200
3.0 H12@200
3.0 H12@200
3.1 H12@200
3.2 H12@200
5200
2.1 H12@200
2.4 H12@150
2.6 H12@200
2.7 H12@200
2.7 H12@200
2.8 H12@200
2.8 H12@200
5400
1.8 H12@200
2.2 H12@150
2.3 H12@150
2.4 H12@200
2.4 H12@200
2.5 H12@200
2.5 H12@200
5600
2.0 H12@150
2.1 H12@150
2.2 H12@150
2.2 H12@200
2.2 H12@200
2.2 H12@200
5800
1.7 H12@150
1.9 H12@150
2.0 H12@150
2.0 H12@150
2.0 H12@200
2.0 H12@200
1.8 H12@150
1.8 H12@150
1.8 H12@150
1.8 H12@200
1.8 H12@200
6000
October 2006
200
Hibond Flooring System
3.3.5 HIBOND COMPOSITE SLAB LOAD SPAN TABLES continued
0.75mm HIBOND INTERNAL SPANS
Medium and Long Term Superimposed Loads (kPa) and Negative Reinforcement (mm2/m width)
Slab Thickness (Ds) mm
L (mm)
110
120
140
150
160
170
180
190
200
2000
17.2 H12@250
22.4 H12@200
2200
14.0 H12@250
18.2 H12@200
21.6 H12@200
2400
11.5 H12@250
15.1 H12@200
18.3 H12@200
20.5 H12@200
21.3 H12@200
19.3 H12@200
19.8 H12@200
20.3 H12@200
2600
9.6 H12@250
12.6 H12@200
15.5 H12@200
16.7 H12@200
17.2 H12@200
17.6 H12@200
18.1 H12@200
18.5 H12@200
18.9 H12@200
19.0 H12@200
2800
8.1 H12@250
10.7 H12@200
13.3 H12@200
14.8 H12@200
15.8 H12@200
16.2 H12@200
16.6 H12@200
16.9 H12@200
17.3 H12@200
17.6 H12@200
3000
6.9 H12@250
9.1 H12@200
11.4 H12@200
12.8 H12@200
14.2 H12@200
14.9 H12@200
15.3 H12@200
15.6 H12@200
15.9 H12@200
16.2 H12@200
3200
5.9 H12@250
7.8 H12@200
9.8 H12@200
11.2 H12@200
12.3 H12@200
13.6 H12@200
14.1 H12@200
14.4 H12@200
14.7 H12@200
15.0 H12@200
3400
5.1 H12@250
6.7 H12@200
8.5 H12@200
9.8 H12@200
10.8 H12@200
11.8 H12@200
12.9 H12@200
13.4 H12@200
13.6 H12@200
13.9 H12@200
3600
4.4 H12@250
5.9 H12@200
7.4 H12@200
8.7 H12@200
9.5 H12@200
10.4 H12@200
11.3 H12@200
12.2 H12@200
12.7 H12@200
12.9 H12@200
3800
3.8 H12@250
4000
3.3 H12@250
5.1 H12@200
6.5 H12@200
7.7 H12@150
8.4 H12@200
9.2 H12@200
10.0 H12@200
10.8 H12@200
11.5 H12@200
12.0 H12@200
4.5 H12@200
5.7 H12@200
6.9 H12@150
7.5 H12@200
8.2 H12@200
8.9 H12@200
9.5 H12@200
10.2 H12@200
10.8 H12@200
4200
2.8 H12@250
3.9 H12@200
5.0 H12@200
6.2 H12@150
6.7 H12@150
7.3 H12@200
7.9 H12@200
8.5 H12@200
9.0 H12@200
9.6 H12@200
4400
2.5 H12@250
3.4 H12@200
4.4 H12@200
5.5 H12@150
6.1 H12@150
6.6 H12@200
7.1 H12@200
7.6 H12@200
8.0 H12@200
8.5 H12@200
4600
2.1 H12@250
3.0 H12@200
3.9 H12@200
4.8 H12@150
5.5 H12@150
5.9 H12@150
6.4 H12@200
6.8 H12@200
7.2 H12@200
7.6 H12@200
4800
1.9 H12@250
2.6 H12@200
3.4 H12@200
4.3 H12@150
5.0 H12@150
5.4 H12@150
5.8 H12@150
6.1 H12@200
6.4 H12@200
6.8 H12@200
5000
1.6 H12@250
2.3 H12@200
3.0 H12@200
3.8 H12@150
4.5 H12@150
4.9 H12@150
5.2 H12@150
5.5 H12@200
5.8 H12@200
6.1 H12@200
5200
2.0 H12@200
2.7 H12@200
3.4 H12@150
4.1 H12@150
4.4 H12@150
4.7 H12@150
5.0 H12@150
5.2 H12@200
5.5 H12@200
5400
1.8 H12@200
2.3 H12@200
3.0 H12@150
3.8 H12@150
4.1 H12@150
4.3 H12@150
4.5 H12@150
4.7 H12@200
4.9 H12@200
5600
1.5 H12@200
2.1 H12@200
2.7 H12@150
3.3 H12@150
3.7 H12@150
3.9 H12@150
4.1 H12@150
4.3 H12@200
4.4 H12@200
5800
1.8 H12@200
2.4 H12@150
3.0 H12@150
3.4 H12@150
3.6 H12@150
3.7 H12@150
3.9 H12@150
4.0 H12@200
6000
1.6 H12@200
2.1 H12@150
2.7 H12@150
3.1 H12@150
3.3 H12@150
3.4 H12@150
3.5 H12@150
3.6 H12@200
6200
1.8 H12@150
2.4 H12@150
2.9 H12@150
3.0 H12@150
3.1 H12@150
3.2 H12@150
3.3 H12@150
6400
1.6 H12@150
2.1 H12@150
2.6 H12@150
2.8 H12@150
2.8 H12@150
2.9 H12@150
3.0 H12@150
6600
1.9 H12@150
2.3 H12@150
2.5 H12@150
2.6 H12@150
2.7 H12@150
2.7 H12@150
6800
1.6 H12@150
2.1 H12@150
2.4 H12@150
2.4 H12@150
2.4 H12@150
2.5 H12@150
1.8 H12@150
2.2 H12@150
2.2 H12@150
2.2 H12@150
2.2 H12@150
7000
October 2006
130
Hibond Flooring System
3.3.5 HIBOND COMPOSITE SLAB LOAD SPAN TABLES continued
0.95mm HIBOND SINGLE SPANS
Medium term superimposed loads (kPa)
Lss
mm
2000
2200
2400
2600
2800
3000
3200
3400
3600
3800
4000
4200
4400
4600
4800
5000
5200
5400
5600
5800
6000
110
120
17.8
14.7
12.3
10.5
9.0
7.8
6.9
6.1
5.4
4.9
4.4
4.0
3.3
2.7
2.1
1.6
21.7
17.8
14.9
12.6
10.9
9.4
8.2
7.3
6.4
5.8
5.2
4.7
4.2
3.8
3.0
2.4
1.9
130
140
19.1
15.9
13.5
11.5
10.0
8.7
7.6
6.8
6.0
5.4
4.9
4.4
4.0
3.6
3.3
2.8
2.2
1.7
21.4
17.8
15.0
12.8
11.1
9.6
8.4
7.5
6.6
5.9
5.3
4.8
4.3
3.9
3.6
3.3
3.0
2.5
2.0
1.5
Slab thickness (Ds) mm
150
160
170
180
190
200
20.1
17.1
14.6
12.6
10.9
9.6
8.4
7.5
6.6
5.9
5.3
4.8
4.3
3.9
3.5
3.2
2.9
2.7
21.9
18.5
15.8
13.6
11.8
10.3
9.0
7.9
7.0
6.3
5.6
5.0
4.5
4.0
3.6
3.3
3.0
2.7
19.9
16.9
14.5
12.6
10.9
9.6
8.4
7.4
6.6
5.8
5.2
4.7
4.2
3.7
3.4
3.0
2.7
21.4
18.2
15.6
13.4
11.7
10.2
8.9
7.8
6.9
6.1
5.4
4.8
4.3
3.9
3.5
3.1
2.8
Slab thickness (Ds) mm
150
160
170
180
190
200
21.9
18.5
15.8
13.6
11.8
10.3
9.0
7.9
7.0
6.3
5.6
5.0
4.5
4.0
3.6
3.3
3.0
2.5
19.9
16.9
14.5
12.6
10.9
9.6
8.4
7.4
6.6
5.8
5.2
4.7
4.2
3.7
3.4
3.0
2.7
21.4
18.2
15.6
13.4
11.7
10.2
8.9
7.8
6.9
6.1
5.4
4.8
4.3
3.9
3.5
3.1
2.8
19.8
16.7
14.2
12.2
10.6
9.2
8.1
7.2
6.4
5.7
5.2
4.6
4.2
3.8
3.5
3.2
2.9
2.7
2.2
21.9
18.4
15.6
13.4
11.6
10.1
8.9
7.8
6.9
6.2
5.5
5.0
4.5
4.1
3.7
3.4
3.1
2.8
2.6
0.95mm HIBOND SINGLE SPANS
Long term superimposed loads (kPa)
Lss
mm
2000
2200
2400
2600
2800
3000
3200
3400
3600
3800
4000
4200
4400
4600
4800
5000
5200
5400
5600
5800
6000
October 2006
110
120
17.8
14.7
12.3
10.5
9.0
7.8
6.9
5.9
4.9
3.9
3.0
2.4
1.8
21.7
17.8
14.9
12.6
10.9
9.4
8.2
7.3
6.4
5.3
4.2
3.3
2.6
2.0
1.5
130
140
19.1
15.9
13.5
11.5
10.0
8.7
7.6
6.8
6.0
5.4
4.6
3.6
2.9
2.2
1.7
21.4
17.8
15.0
12.8
11.1
9.6
8.4
7.5
6.6
5.9
5.3
4.8
3.9
3.1
2.4
1.9
19.8
16.7
14.2
12.2
10.6
9.2
8.1
7.2
6.4
5.7
5.2
4.6
4.2
3.3
2.6
2.0
1.5
21.9
18.4
15.6
13.4
11.6
10.1
8.9
7.8
6.9
6.2
5.5
5.0
4.5
4.1
3.5
2.8
2.2
1.7
20.1
17.1
14.6
12.6
10.9
9.6
8.4
7.5
6.6
5.9
5.3
4.8
4.3
3.9
3.5
3.0
2.3
1.8
Hibond Flooring System
3.3.5 HIBOND COMPOSITE SLAB LOAD SPAN TABLES continued
0.95mm HIBOND DOUBLE AND END SPANS
Medium and Long Term Superimposed Loads (kPa) and Negative Reinforcement (mm2/m width)
Slab Thickness (Ds) mm
L (mm)
110
120
130
140
150
160
170
180
190
200
2000
14.2 H12@250
17.3 H12@200
18.6 H12@250
20.9 H12@250
2200
11.4 H12@250
14.3 H12@200
15.3 H12@250
17.1 H12@250
19.1 H12@250
21.2 H12@250
2400
9.3 H12@250
11.9 H12@200
12.7 H12@250
14.3 H12@250
15.8 H12@250
17.5 H12@250
19.2 H12@250
20.9 H12@250
2600
7.7 H12@250
10.1 H12@200
10.8 H12@250
12.0 H12@250
13.3 H12@250
14.7 H12@250
16.1 H12@250
17.5 H12@250
18.9 H12@250
20.0 H12@250
2800
6.4 H12@250
8.4 H12@200
9.2 H12@200
10.3 H12@250
11.3 H12@250
12.5 H12@250
13.6 H12@250
14.8 H12@250
15.9 H12@250
17.2 H12@250
3000
5.3 H12@250
7.1 H12@200
8.0 H12@200
8.9 H12@200
9.8 H12@200
10.7 H12@200
11.7 H12@200
12.6 H12@250
13.5 H12@250
14.6 H12@200
3200
4.5 H12@250
6.0 H12@200
7.0 H12@200
7.7 H12@200
8.5 H12@200
9.3 H12@200
10.1 H12@200
10.9 H12@200
11.6 H12@200
12.5 H12@200
3400
3.8 H12@250
5.1 H12@200
6.1 H12@200
6.8 H12@200
7.4 H12@200
8.1 H12@200
8.8 H12@200
9.4 H12@200
10.0 H12@200
10.7 H12@200
3600
3.2 H12@250
4.3 H12@200
5.4 H12@200
6.0 H12@200
6.5 H12@200
7.1 H12@200
7.7 H12@200
8.2 H12@200
8.7 H12@200
9.3 H12@200
3800
2.7 H12@250
4000
2.2 H12@250
3.7 H12@200
4.8 H12@200
5.3 H12@200
5.8 H12@200
6.3 H12@200
6.7 H12@200
7.2 H12@200
7.6 H12@200
8.1 H12@200
3.1 H12@200
4.1 H12@200
4.7 H12@200
5.1 H12@200
5.6 H12@200
6.0 H12@200
6.3 H12@200
6.7 H12@200
7.1 H12@200
4200
1.9 H12@250
2.6 H12@200
3.5 H12@200
4.2 H12@200
4.6 H12@200
5.0 H12@200
5.3 H12@200
5.6 H12@200
5.9 H12@200
6.3 H12@200
4400
2.2 H12@200
3.0 H12@200
3.8 H12@200
4.1 H12@200
4.4 H12@200
4.7 H12@200
5.0 H12@200
5.3 H12@200
5.5 H12@200
4600
1.9 H12@200
2.6 H12@200
3.4 H12@150
3.7 H12@150
4.0 H12@200
4.2 H12@200
4.5 H12@200
4.7 H12@200
4.9 H12@200
4800
2.2 H12@200
2.9 H12@150
3.4 H12@150
3.6 H12@150
3.8 H12@200
4.0 H12@200
4.2 H12@200
4.4 H12@200
5000
1.8 H12@200
2.5 H12@150
3.1 H12@150
3.3 H12@150
3.4 H12@200
3.6 H12@200
3.7 H12@200
3.9 H12@200
5200
2.1 H12@150
2.8 H12@150
3.0 H12@150
3.1 H12@150
3.2 H12@200
3.3 H12@200
3.5 H12@200
5400
1.8 H12@150
2.4 H12@150
2.7 H12@150
2.8 H12@150
2.9 H12@150
3.0 H12@200
3.1 H12@200
5600
2.1 H12@150
2.5 H12@150
2.6 H12@150
2.6 H12@150
2.7 H12@150
2.8 H12@200
5800
1.7 H12@150
2.2 H12@150
2.3 H12@150
2.4 H12@150
2.4 H12@150
2.5 H12@150
2.0 H12@150
2.1 H12@150
2.2 H12@150
2.2 H12@150
2.2 H12@150
6000
October 2006
Hibond Flooring System
3.3.5 HIBOND COMPOSITE SLAB LOAD SPAN TABLES continued
0.95mm HIBOND INTERNAL SPANS
Medium and Long Term Superimposed Loads (kPa) and Negative Reinforcement (mm2/m width)
Slab Thickness (Ds) mm
L (mm)
110
120
130
140
150
160
170
180
190
200
2000
17.2 H12@250
22.4 H12@200
2200
14.0 H12@250
18.2 H12@200
23.0 H12@200
2400
11.5 H12@250
15.1 H12@200
19.1 H12@200
22.8 H12@150
2600
9.6 H12@250
12.6 H12@200
16.0 H12@200
19.3 H12@150
21.5 H12@150
2800
8.1 H12@250
10.7 H12@200
13.6 H12@200
16.5 H12@150
18.4 H12@150
19.4 H12@200
19.9 H12@200
20.3 H12@200
3000
6.9 H12@250
9.1 H12@200
11.6 H12@200
14.1 H12@150
15.8 H12@150
17.5 H12@150
18.3 H12@150
18.7 H12@200
19.1 H12@200
19.5 H12@200
3200
5.9 H12@250
7.8 H12@200
10.0 H12@200
12.2 H12@150
13.8 H12@150
15.2 H12@150
16.7 H12@150
17.4 H12@150
17.7 H12@200
18.0 H12@200
3400
5.1 H12@250
6.7 H12@200
8.7 H12@200
10.6 H12@150
12.1 H12@150
13.3 H12@150
14.6 H12@150
15.8 H12@150
16.5 H12@150
16.8 H12@200
3600
4.4 H12@250
5.9 H12@200
7.6 H12@200
9.3 H12@150
10.7 H12@150
11.7 H12@150
12.8 H12@150
13.9 H12@150
14.9 H12@150
15.6 H12@150
3800
3.8 H12@250
5.1 H12@200
6.6 H12@200
8.1 H12@150
9.5 H12@150
10.4 H12@150
11.3 H12@150
12.2 H12@150
13.1 H12@150
14.1 H12@150
4000
3.3 H12@250
4.5 H12@200
5.8 H12@200
7.2 H12@150
8.5 H12@150
9.3 H12@150
10.1 H12@150
10.8 H12@150
11.6 H12@150
12.5 H12@150
4200
2.8 H12@250
3.9 H12@200
5.1 H12@200
6.3 H12@150
7.6 H12@150
8.3 H12@150
9.0 H12@150
9.7 H12@150
10.3 H12@150
11.1 H12@150
4400
2.5 H12@250
3.4 H12@200
4.5 H12@200
5.6 H12@150
6.8 H12@150
7.5 H12@150
8.1 H12@150
8.7 H12@150
9.2 H12@150
9.9 H12@150
4600
2.1 H12@250
3.0 H12@200
4.0 H12@200
5.0 H12@150
6.0 H12@150
6.7 H12@150
7.3 H12@150
7.8 H12@150
8.3 H12@150
8.8 H12@150
4800
1.9 H12@250
2.6 H12@200
3.5 H12@200
4.4 H12@150
5.4 H12@150
6.1 H12@150
6.6 H12@150
7.0 H12@150
7.4 H12@150
7.9 H12@150
5000
1.6 H12@250
2.3 H12@200
3.1 H12@200
3.9 H12@150
4.8 H12@150
5.6 H12@150
6.0 H12@150
6.3 H12@150
6.7 H12@150
7.1 H12@150
5200
2.0 H12@200
2.7 H12@200
3.5 H12@150
4.3 H12@150
5.1 H12@150
5.4 H12@150
5.8 H12@150
6.1 H12@150
6.4 H12@150
5400
1.8 H12@200
2.4 H12@200
3.1 H12@150
3.8 H12@150
4.6 H12@150
5.0 H12@150
5.2 H12@150
5.5 H12@150
5.8 H12@150
5600
1.5 H12@200
2.1 H12@200
2.7 H12@150
3.4 H12@150
4.2 H12@150
4.5 H12@150
4.8 H12@150
5.0 H12@150
5.3 H12@150
5800
1.9 H12@200
2.4 H12@150
3.1 H12@150
3.8 H12@150
4.2 H12@150
4.4 H12@150
4.6 H12@150
4.8 H12@150
6000
1.6 H12@200
2.2 H12@150
2.7 H12@150
3.4 H12@150
3.8 H12@150
4.0 H12@150
4.2 H12@150
4.4 H12@150
6200
1.9 H12@150
2.4 H12@150
3.0 H12@150
3.5 H12@150
3.7 H12@150
3.8 H12@150
4.0 H12@150
6400
1.7 H12@150
2.2 H12@150
2.7 H12@150
3.2 H12@150
3.4 H12@150
3.5 H12@150
3.6 H12@150
6600
1.9 H12@150
2.4 H12@150
3.0 H12@150
3.1 H12@150
3.2 H12@150
3.3 H12@150
6800
1.7 H12@150
2.1 H12@150
2.7 H12@150
2.9 H12@150
2.9 H12@150
3.0 H12@150
1.9 H12@150
2.4 H12@150
2.6 H12@150
2.7 H12@150
2.8 H12@150
7000
October 2006
