K Service Source
Macintosh
K Service Source
Basics
Macintosh
Basics
Overview - 1
Overview
This manual includes repair
procedures for the earliest
Apple Macintosh
computersthe Macintosh
128K and Macintosh 512K.
Figure: Macintosh 128k/512K
K Service Source
Specifications
Macintosh
Specifications
Processor - 1
Processor
CPU
Motorola 68000 microprocessor
7.83 MHz
32-bit internal data bus
Specifications
Memory - 2
Memory
RAM
ROM
PRAM
128K or 512K
64K
CMOS custom chip with 4.5 V, user-replaceable battery backup
(includes 256 bytes of memory; remembers system
parameters even with the machine switched off)
Specifications
Disk Storage - 3
Disk Storage
Floppy Drive
Internal, single-sided drive; uses 3.5-in., hard-case, 400K
floppy disks
Specifications
I/O Interfaces - 4
I/O Interfaces
Floppy Drive
External drive port; DB-19 connector
Mouse
Mouse port; DE-9 connector
Keyboard
Synchronous serial keyboard bus; RJ-11 connector
Serial
Two RS-232/RS-422 serial ports; DE-9 connectors
Specifications
I/O Devices - 5
I/O Devices
Keyboard
58 keys; software mapped; RJ-11 connector
Mouse
Mechanical tracking; optical shaft encoding at 3.54 pulses per mm
(90 pulses per in.) of travel; DE-9 connector
Specifications
Sound and Video - 6
Sound and Video
Sound Generator
Four-voice sound with 8-bit digital/analog conversion, using
22-kHz sampling rate
Video Display
9-in. (diagonal) screen; 512 x 342 pixel, bit-mapped display
Specifications
Electrical - 7
Electrical
Line Voltage
105125 VAC
Frequency
5060 Hz
Maximum Power
60 W
Specifications
Physical - 8
Physical
Dimensions
Weight
Height: 13.6-in. (34.5 cm)
Width: 9.6-in. (24.4 cm)
Depth: 10.9-in. (27.6 cm)
16 lb. 8 oz. (7.5 kg)
K Service Source
Troubleshooting
Macintosh
Troubleshooting
General/ - 1
General
The Symptom Charts included in this chapter will help you
diagnose specific symptoms related to your product. Because
cures are listed on the charts in the order of most likely solution,
try the first cure first. Verify whether or not the product
continues to exhibit the symptom. If the symptom persists, try
the next cure. (Note: If you have replaced a module, reinstall the
original module before you proceed to the next cure.)
If you are not sure what the problem is, or if the Symptom Charts
do not resolve the problem, refer to the Flowchart for the product
family.
For additional assistance, contact Apple Technical Support.
Troubleshooting
Symptom Charts/Video - 2
Symptom Charts
Video
No video, but audio
tone is present and
drive operates
1
2
3
4
5
Turn contrast control fully clockwise.
Check video cable connections.
Replace power supply board.
Replace neck cable.
Replace logic board. Retain customers SIMMs.
Screen is bright and
audio is present, but
no video information
is present
1
2
Replace power supply board.
Replace logic board. Retain customers SIMMs.
Troubleshooting
Symptom Charts/Drives - 3
Drives
Disk ejects; display
shows disk icon with
blinking X
1
2
3
4
Replace
Replace
Replace
Replace
Unable to insert disk
all the way
Insert opened paper clip into small hole beside drive slot, or
switch off system power and hold mouse button down
while switching system power back on to complete eject
cycle. Then insert disk with metal slot forward and writeprotect tab on bottom.
Replace floppy drive.
bad disk.
floppy drive cable.
drive.
logic board. Retain customers SIMMs.
Troubleshooting
Symptom Charts/Drives (Continued) - 4
Drives (Continued)
Drive does not eject
disk
Insert opened paper clip into small hole beside drive slot, or switch
off system power and hold mouse button down while switching
system power back on to complete eject cycle.
Does not read disks
on internal drive
1
2
3
4
5
6
Replace bad disk.
Replace floppy drive cable.
Replace Mylar RFI shield.
Replace floppy drive.
Verify ROMs on the logic board (refer to Additional
Procedures).
Replace logic board. Retain customers SIMMs.
Troubleshooting
Symptom Charts/Peripherals - 5
Peripherals
Cursor does not move
1
2
3
Connect mouse.
Replace mouse.
Replace logic board. Retain customers SIMMs.
Cursor moves, but
clicking mouse
produces no response
1
2
Replace mouse.
Replace logic board. Retain customers SIMMs.
No response to any
key on keyboard
1
2
3
Replace keyboard cable.
Replace keyboard.
Replace logic board. Retain customers SIMMs.
No response from a
particular key
1
2
3
Replace keyswitch.
Replace keyboard.
Replace logic board. Retain customers SIMMs.
Troubleshooting
Symptom Charts/Peripherals (Continued) - 6
Peripherals (Continued)
Known-good
ImageWriter or
ImageWriter II does
not print
1
2
Known-good
LaserWriter does not
print
1
2
3
4
5
Make sure that Chooser and Control Panel are set correctly
Check that system software version is compatible. Replace
software with known-good version.
Reset PRAM.
Replace interface cable.
Replace logic board. Retain customers SIMMs.
Make sure that Chooser and Control Panel are set correctly.
Check that system software version is compatible. Replace
software with known-good version.
Reset PRAM.
Troubleshooting
Symptom Charts/Miscellaneous - 7
Miscellaneous
When turned on, the
Macintosh
continuously beeps
and tries to power up
1
2
Clicking or chirping
sound
1
2
3
4
3
4
Perform voltage adjustment. Refer to Adjustments chapter.
Disconnect internal disk drive. If this eliminate problem,
replace drive.
Replace logic board. Retain customers SIMMs.
Caution: Replacing only power supply board may damage
new power supply board. Replace power supply board, logic
board, and internal drive, then turn on Macintosh.
Connect logic board cable.
Perform voltage adjustment. Refer to Adjustments chapter.
Replace power supply board.
Replace logic board. Retain customers SIMMs.
Troubleshooting
Symptom Charts/Miscellaneous (Continued) - 8
Miscellaneous (Continued)
Smoke/odor issues
from the Macintosh
Caution: Replacing only power supply board may damage new
power supply board. Replace power supply board, logic board, and
internal drive, then turn on Macintosh.
No video, no audio
tone, and no drive
operation
1
2
3
4
5
6
Connect power cord.
Turn on power.
Replace power cord.
Check fuse.
Caution: Replacing only power supply board may damage
new power supply board. Replace power supply board, logic
board, and internal drive, then turn on Macintosh.
Replace logic board. Retain customers SIMMs.
Troubleshooting
Symptom Charts/Miscellaneous (Continued) - 9
Miscellaneous (Continued)
When developers
switch is installed,
Macintosh sometimes
resets intermittently
Remove switch and file it down about 1/16 inch.
Macintosh 512K
enhanced has two RFI
shields
Some machines have two RFI shrouds installed. Two RFI shields
can be replaced by one RFI shield, which can be ordered as a
service part.
K Service Source
Take Apart
Macintosh
Take Apart
Cover - 1
Cover
No preliminary steps are
required before you begin
this procedure.
Warning: This product
contains high voltage and a
high-vacuum picture tube.
To prevent serious injury
or equipment damage,
review CRT safety and
discharge instructions in
Bulletins/Safety.
Take Apart
Cover - 2
1
Cover
Battery
Compartment
Cover
Reset/Interrupt
Switch
Remove the battery
compartment cover.
Remove the reset/
interrupt switch, if
present.
Take Apart
Cover - 3
3
Using a Torx
screwdriver, remove
the four case screws.
Using the pull-apart
tool, gently pry off the
cover.
Warning: The edges of
the metal chassis may
be sharp. When moving
the computer with the
cover off, be sure to
handle the chassis
carefully.
Take Apart
Cover - 4
5
RFI Shield
Remove the RFI shield.
Take Apart
Ground Lug
Anode Cap
Power/Sweep Board - 5
Power/Sweep
Board
Power/Sweep
Board
Before you begin,
Remove the cover
Discharge the CRT
Remove the anode cap
This product
contains high voltage and a
high-vacuum picture tube.
To prevent serious personal
injury or equipment
damage, review CRT safety
and discharge instructions
Bulletins/Safety.
Warning:
Discharge
Tool
Take Apart
Power/Sweep Board - 6
Yoke Cable
Logic Board
Cable
Neck Cable
Never use a
grounding wriststrap until
after discharging the CRT.
Warning:
2
Screw and
Lockwasher
Disconnect the following
cable connectors from
the power/sweep board:
Yoke cable
Logic board cable
Neck cable
Remove the screw and
lockwasher that hold the
ground wire to the
chassis.
Take Apart
Power/Sweep Board - 7
3
Note: You may need to
remove the insulating
paper from the power/
sweep board to access the
mounting screws.
Remove the three
mounting screws and
washers, and lift the
power/sweep board
from the chassis.
Replacement Note: After
replacing all parts except
the cover, perform the
voltage and video
adjustment procedures. See
Voltage and Video in the
Adjustments chapter.
Take Apart
Power/Sweep Board - 8
Replacement Note: When
sending a defective power/
sweep board to Apple, be
sure to include the cable that
connects to the logic board.
Be sure the contrast control
knob and battery have been
removed from the defective
board and reinstalled onto
the exchange board.
Take Apart
Logic Board - 9
Logic Board
Before you begin,
Remove the cover
Discharge the CRT
Warning: This product
contains high voltage and a
high-vacuum picture tube.
To prevent serious personal
injury or equipment
damage, review CRT safety
and discharge instructions
in Bulletins/Safety.
Logic Board
Take Apart
Logic Board - 10
Never use a
grounding wriststrap until
after discharging the CRT.
Warning:
Logic
Board
Cable
Floppy Drive Cable
Disconnect the following
cable connectors from
the logic board:
Floppy drive cable
Logic board cable
Take Apart
Logic Board - 11
2
Caution: When
removing the logic
board, be careful not to
damage the SIMMs
especially the larger DIP
SIMMs that may be
installed on the board.
Pull back on the top of
the logic board, and
carefully slide out the
logic board.
Replacement Note: After
replacing all parts except
the cover, perform the
voltage and video
adjustment procedures. See
Voltage in Adjustments.
Take Apart
Logic Board - 12
Replacement Note: When
exchanging the 512K logic
board, you must swap ROMs
to the new logic board.
Replacement Note: Remove
the SIMMs from the
defective logic board and
install them on the
replacement logic board.
See Hardware/Memory.
Take Apart
CRT - 13
CRT
CRT
Before you begin,
Remove the cover
Discharge the CRT
Remove the Power/
Sweep board
Warning: This product
contains high voltage and a
high-vacuum picture tube.
To prevent serious personal
injury, review CRT safety
and discharge instructions
in Bulletins/Safety.
Take Apart
CRT - 14
Never use a
grounding wriststrap until
after discharging the CRT.
Warning:
Handle the CRT
by its sides only. Do not
grasp the neck on the CRT or
touch the anode.
Warning:
Ground
Wire
Slide the CRT socket
cable straight off the
neck of the CRT.
Remove the four
mounting screws and the
ground wire, and lift the
CRT off the bezel.
Take Apart
CRT - 15
If you must
dispose of the CRT, refer to
CRT Disposal in
Bulletins/Safety.
Warning:
Replacement Note: If you
replace the CRT, perform
the video and yoke
adjustment procedures. See
Video and Yoke in the
Adjustments chapter.
Take Apart
Floppy Drive - 16
Floppy Drive
Before you begin,
Remove the cover
Discharge the CRT
Remove the logic board
Floppy Drive
This product
contains high voltage and a
high-vacuum picture tube.
To prevent serious personal
injury or equipment
damage, review CRT safety
and discharge instructions
in Bulletins/Safety.
Warning:
Take Apart
Floppy Drive - 17
Floppy Drive
Never use a
grounding wriststrap until
after discharging the CRT.
Warning:
Remove the four mounting
screws, and slide the floppy
drive out of the chassis.
Take Apart
Floppy Drive - 18
Replacement Note: All
400K drives are shipped in
their original drive shields.
When installing a new
800K drive, remove the
shipping fixture, plastic
dust shield (if any), and
packing disk from the new
drive. Install the new drive
in the customers original
drive shield.
Note: Before you install a
replacement drive, remove
the dust shield, if there is
one.
Take Apart
Chassis - 19
Chassis
Before you begin,
Remove the cover
Discharge the CRT
Remove the logic board
Remove the Power/
Sweep board
Remove the floppy drive
Warning: This product
contains high voltage and a
high-vacuum picture tube.
To prevent serious personal
injury or equipment
damage, review CRT safety
and discharge instructions
in Bulletins/Safety.
Chassis
Take Apart
Chassis - 20
Never use a
grounding wriststrap until
after discharging the CRT.
Warning:
Remove the five mounting
screws and lift the chassis
off the bezel.
K Service Source
Upgrades
Macintosh
Upgrades
Floppy Drive Upgrade Kit - 1
Floppy Drive
Upgrade Kit
Floppy Drive
Before you begin,
Remove the cover
Discharge the CRT
Remove the logic board
This product
contains high voltage and a
high-vacuum picture tube.
To prevent serious personal
injury or equipment
damage, review CRT safety
and discharge instructions
in Bulletins/Safety.
Warning:
Upgrades
Floppy Drive Upgrade Kit - 2
Never use a
grounding wriststrap until
after discharging the CRT.
Warning:
D5
D8
Note: This kit replaces the
400K floppy drive on a
512K Macintosh with an
800K floppy drive. The kit
contains the new drive and
two new ROMs for the logic
board. The new ROMs
support both the 400K and
the 800K drives. This
upgrade is not recommended
for the 128K Macintosh.
Upgrades
Floppy Drive Upgrade Kit - 3
1
2
D5
D8
Using an IC extractor,
remove the old ROMs
from locations D5 and
D8.
Install the two new ROMs
as follows:
ROM HI at location D5
ROM LOW at location
D8
Note: Be sure that the
notched ends of the
ROMs face the front of
the computer.
Upgrades
Floppy Drive Upgrade Kit - 4
3
Remove the floppy drive.
Refer to Floppy
Drive in the Take Apart
chapter.
Upgrades
Floppy Drive Upgrade Kit - 5
4
Reinstall the logic board.
See Logic Board in
the Take Apart chapter.
Upgrades
Floppy Drive Upgrade Kit - 6
5
Install the new 800K
floppy drive. See
Floppy Drive in the
Take Apart chapter.
Return the old ROMs and
the 400K drive to Apple
(refer to the
instructions in the kit).
Upgrades
Logic Board Upgrade Kit - 7
Logic Board
Upgrade Kit
Before you begin,
Remove the cover
Discharge the CRT
Remove the logic board
This product
contains high voltage and a
high-vacuum picture tube.
To prevent serious personal
injury or equipment
damage, review CRT safety
and discharge instructions
in Bulletins/Safety.
Warning:
Logic Board
Upgrades
Logic Board Upgrade Kit - 8
Never use a
grounding wriststrap until
after discharging the CRT.
Warning:
D5
D8
Note: This kit cannot be
installed unless the Floppy
Drive Upgrade Kit has been
installed. The Logic Board
Upgrade Kit upgrades the
logic board of a 512K Mac to
a Mac Plus. The kit contains
a new logic board with 1 MB
of RAM, an RFI shield, and a
new rear cover.
Upgrades
Logic Board Upgrade Kit - 9
1
2
D5
D8
Using an IC extractor,
remove the ROMs from
locations D5 and D8 on
the 512K logic board.
Install the two ROMs in
the new logic board:
ROM HI at location D5
ROM LOW at location
D8
Note: Be sure that the
notched ends of the
ROMs face the front of
the computer.
Upgrades
Logic Board Upgrade Kit - 10
3
Install the new logic
board in the computer.
See Logic Board in
the Take Apart chapter.
Upgrades
Logic Board Upgrade Kit - 11
4
5
Install the new RFI
shield.
Install the new cover.
See Cover in the Take
Apart chapter.
Return the old logic
board, old RFI shield,
and old cover to Apple.
Upgrades
400K Drive ROM Upgrade - 12
400K Drive ROM
Upgrade
Before you begin,
Remove the cover
Discharge the CRT
Remove the logic board
This product
contains high voltage and a
high-vacuum picture tube.
To prevent serious personal
injury or equipment
damage, review CRT safety
and discharge instructions
in Bulletins/Safety.
Warning:
Logic Board
Upgrades
400K Drive ROM Upgrade - 13
Never use a
grounding wriststrap until
after discharging the CRT.
Warning:
D5
D8
Note: Current 400K drives
contain a new stepper motor
that requires the
replacement of the two boot
ROMs on the Macintosh
128K and 512K. The new
ROMs are compatible with
new and old stepper motors.
1
Using an IC extractor,
remove the ROMs at
locations D5 and D8.
Upgrades
400K Drive ROM Upgrade - 14
2
D5
D8
Install the two new ROMs
on the logic board:
ROM HI at location D5
ROM LOW at location
D8
Note: Be sure that the
notched ends of the
ROMs face the front of
the computer.
Upgrades
400K Drive ROM Upgrade - 15
3
Reinstall the logic board
in the computer. See
Logic Board in the
Take Apart chapter.
K Service Source
Adjustments
Macintosh
Adjustments
Voltage - 1
Voltage
Before you begin, remove
the cover.
This product
contains high voltage and a
high-vacuum picture tube.
To prevent serious personal
injury or equipment
damage, review CRT safety
and discharge instructions
in Bulletins/Safety.
Warning:
Adjustments
Voltage - 2
Power/Sweep
Board
Caution: Because you must
make voltage adjustments
from the rear of the
computer, use a mirror to
view the computer screen.
Do not reach around the
computer to adjust the
controls.
Note: You must verify
voltages after you replace
the logic board or the
power/sweep board.
External
Drive Port
Adjustments
Voltage - 3
1
2
Set the voltmeter to 20 V
scale.
Connect the Macintosh
voltage test cable (Apple
part number 0770135) to the external
drive port.
Caution: Shorting the test
cable plugs to each other can
damage the Macintosh
computer. Pull the rubber
hoods over the plugs.
External
Drive Port
Connect the black
voltmeter test lead
between the voltmeter
Adjustments
Voltage - 4
Voltage
Regulator
Power/Sweep
Board
5
6
7
8
ground terminal and the
computer chassis.
Connect the orange test
cable lead to the voltage
input terminal on the
voltmeter.
Switch on the computer.
Adjust the voltage
regulator on the power/
sweep board to between
11.90 V and 12.75 V.
Switch off the power.
Disconnect the orange
test lead and pull the
insulated hood over the
plug.
Adjustments
Voltage - 5
9
Connect the red test
cable lead to the voltage
input terminal on the
voltmeter.
10 Switch on the computer.
Voltage
Regulator
Power/Sweep
Board
11 Adjust the voltage
regulator on the power/
sweep board to between
4.85 V and 5.15 V.
Adjustments
Voltage - 6
12 Switch off the power.
13 Disconnect the red test
lead
14 and pull the insulated
hood over the plug.
Voltage
Regulator
Power/Sweep
Board
15 Repeat the tests to verify
that both voltages are
within the specified
tolerances.
Note: If the power/sweep
board will not adjust so that
both voltages fall within
tolerance, replace the board.
Adjustments
Yoke - 7
Yoke
Before you begin,
Remove the cover
Discharge the CRT
Warning: This product
contains high voltage and a
high-vacuum picture tube.
To prevent serious personal
injury or equipment
damage, review CRT safety
and discharge instructions
in Bulletins/Safety.
Yoke
Adjustments
Yoke - 8
Caution: Because you must
make yoke adjustments from
the rear of the computer,
use a mirror to view the
computer screen. Do not
reach around the computer
to adjust the controls.
Note: If you replace the
CRT, you may need to adjust
the yoke.
Adjustments
Tilt Adjustment - 9
Tilt Adjustment
Note: If glue holds the yoke
collar in place, use an art
knife to cut through the glue.
Yoke Collar
Yoke Clamp
Screw
Loosen the yoke clamp
screw two or three
turns.
Switch on the computer.
Adjustments
Tilt Adjustment - 10
3
Yoke Collar
With one hand, grasp
the plastic spokes of the
yoke collar and rotate
the yoke collar until the
top and bottom edges of
the picture are parallel
with the top and bottom
of the bezel.
Adjustments
Tilt Adjustment - 11
4
5
6
Yoke Collar
Yoke Clamp
Screw
Switch off and unplug the
computer.
Discharge the CRT.
Caution: Do not
overtighten the yoke
clamp screw.
Hold the plastic collar
in position and slowly
tighten the yoke clamp
screw so that the collar
cannot slip.
Adjustments
Tilt Adjustment - 12
7
8
Replace the cover and
switch on the computer.
Make sure the top and
bottom edges of the
picture are parallel with
the top and bottom of the
bezel.
Adjustments
Tilt Adjustment - 13
Centering Ring
Adjustment
1
2
Turn off the computer
and remove the cover.
Turn on the computer
Note: If glue holds the yoke
collar in place, use an art
knife to cut through the glue.
3
Centering Rings
To center the picture,
hold the front centering
ring steady and move the
rear ring. Then hold the
rear centering ring
steady and move the
front ring.
Adjustments
Video - 14
Power/Sweep
Board
Video
Before you begin, remove
cover.
This product
contains high voltage and a
high-vacuum picture tube.
To prevent serious personal
injury, review CRT safety
and discharge instructions
in Bulletins/Safety.
Warning:
Note: You must perform the
video adjustments whenever
the CRT or the power/sweep
board is replaced.
Switch on the computer.
Adjustments
Video - 15
Contrast and
Brightness
1
Brightness
Control
External
Contrast
Control
Turn the external
contrast control fully
clockwise.
Turn the brightness
control fully
counterclockwise so that
white lines are visible.
Turn the brightness
control clockwise until
the white lines just
disappear.
Turn the external
contrast control 1/8 of a
turn counterclockwise.
Adjustments
Video - 16
Size Adjustment
1
Width Control
Height Control
Using an alignment tool,
adjust the width control
until the raster is 7
inches (177.8 mm)
wide.
Using an alignment tool,
adjust the height control
until the raster is 4.7
inches (119.4 mm)
high.
Adjustments
Video - 17
Focus Adjustment
1
2
Focus Control
Turn the focus control
clockwise to its limit.
Turn the focus control
counterclockwise 1/8 of
a turn.
K Service Source
Exploded View
Macintosh
Exploded View
Exploded View
CRT and Yoke
Assembly
076-0103
Front
Bezel
810-0373
Internal Drive
Shield
805-0765 (400K)
805-0217 (800K)
CRT
Socket
Cable
590-0160
Floppy Drive
661-7615 (400K)
661-0345 (800K)
Internal
Drive
Cable
590-0167 (red)
590-0437 (yellow)
Insulator
Shield
725-0011
Power/Sweep
Board
661-76214
Chassis
805-0766
462-3100
426-1001
Logic Board
661-06236
Rear Housing
630-5139
426-1007
435-5002
RFI Shroud
805-0577
