PRODUCT DATA
www.nortechcontrol.com
Single Channel Loop Detectors
PRODUCT DESCRIPTION
One of the most critical components of the whole vehicle access control
system is the inductive loop detector. Nortechs detectors have been
renowned for their reliability and durability for many years.
Single channel loop detectors are used to identify the presence of vehicles
by means of an inductive loop buried under the road. These single chip
microprocessor-based units benefit from a detect filter and frequency
indicator and are suitable for parking control and motorised door or gate
applications all detectors are CE tested and approved.
A compact detector diagnostic unit is available for extracting data from new
and existing sites.
PD130
FEATURES
PD130 - Vehicle Detector
Compact size
Elegant Styling
Diagnostic capabilities
Selectable permanent presence
Loop isolation protection
Loop frequency indication
Compact size
Selectable permanent presence
Selectable presence output (Fail
Safe / Fail Secure)
Loop isolation protection
Visual output LED (fault monitor)
Automatic Sensitivity Boost (ASB)
Detect filter
PD139 - Card Based Vehicle Detector
GD100 - Vehicle Detector
Compact size
Diagnostic capabilities
Selectable permanent presence
Loop isolation protection
DU100 - Detector Diagnostics Unit
Compact, self-contained test
Exclusive optical readout
No service disruption
Loop diagnosis
Historical data available
Unique crosstalk monitor
Loop frequency indication
Automatic Sensitivity Boost (ASB)
GD100
Selectable relay output configuration
Loop fault monitor
Applications
Parking barrier control
Rising bollards
Motorised gates and doors
Industrial control systems
Rising kerbs
High-speed rapid roll industrial doors
PD139
ISSUE 05
DU100
Single Channel Loop Detectors
Technical Details
PD130
Face-plate LED Indicators:
PD139
GD100
POWER
RSET
+24V DC or 24V AC
0V DC or Nuetral AC
3. Detect - on steady
1 2 3 4 5 6 7 8
PRES
PULSE
FILT
ASB
2. Undetect - off
ON
SENS
FREQ
4. Fault - on with short off
1
PIN 10
PIN 1
MODE
Operating Modes:
1. Limited presence/
permanent presence
RESET
1
2. Pulse on detect/pulse on
undetect
3. Automatic sensitivity
boost off/on
SW1
CH1
1. Tuning - on steady followed
by flashing frequency
count (x 10kHz)
LED1
Green - channel indicator:
LED2
Red - power,
Presence
2
3
Pulse
4. Filter off/on (2 second
delay)
7
9
11
Pulse
Presence
10
Ext Reset
+ DC
- DC
GD 100
6
9
10
N
L
Power
Presence
Pulse
Specifications
PD130/PD139
Self tuning range:
Sensitivity:
20-1500mH
4 step adjustable:
High: 0.02% DL/L; Medium High:
0.05% D L/L; Medium Low: 0.1%
DL/L; Low: 0.5% DL/L
4 step adjustable, 12-80kHz
(frequency determined by loop
geometry)
Frequency:
PD130 Output Relays:
PD139 Output Relay:
Presence output relay - Change-over
contacts (fail-safe) rated at 5A @
230V AC
Pulse output relay - Change-over
contacts (non-fail-safe) rated at 5A
@ 230V AC
Presence output relay - Change-over
contacts (fail-safe) rated at 1A @
230V AC
Pulse output relay - Change-over
contacts (non-fail-safe) rated at 1A @
230V AC
PD130 Pulse output duration: Approx. 150ms, factory option
250ms
PD139 Pulse output duration: Approx. 150ms
Automatic Sensitivity Boost: Switch selectable
Presence time:
1 hour for 3% DL/L, permanent
presence option
Protection:
Loop isolation transformer,
zener diode clamping on loop inputs
and gas discharge tube protection
PD130 Power requirements:
120V AC +/- 15% 48-60Hz (PD131)
230V AC +/- 15% 48-60Hz (PD132)
12-24V AC/DC +/- 15% (PD134)
Requirement: 1.5VA max @ 230V
PD139 Power requirements:
24V AC/DC +/- 15%
Requirement: 1.1VA max @ 24V DC
Operating temp range:
-40oC to +80oC (circuit sealed
against condensation)
PD130: High heat ABS blend
PD130: 76 x 40 x 78; PD139: 105 x
68
PD130: Shelf or DIN-rail socket;
PD139: Panel or plug-in
Material:
Dimensions (mm):
Mounting:
Connector:
Option:
PD130: Single rear mount 11-pin
submagnal (86CP11); PD139: Molex
10-pin female
Flying leads
Ordering Information
PD131:
Single channel, boxed, 120V AC
PD132;
Single channel, boxed, 230V AC
PD134:
Single channel, boxed, 12-24 V AC/DC
PD139:
Single channel, PCB, 24V DC
PD139-FAAC:
Single channel, PCB, designed to fit FAAC
barrier controllers
GD100:
Single channel DIN rail mount detector, 24V
AC/DC
DU100
Detector diagnostic unit
Nortech Control Systems Limited w Nortech House w William Brown Close w Llantarnam Park w Cwmbran w South Wales w NP44 3AB
P: +44 (0) 1633 485533 w F: +44 (0) 1633 485666 w E: [email protected] w W: www.nortechcontrol.com
