TD2 QuickStart Guide
Forensic Duplicator
Solutions for the Digital Evidence Lifecycle
Device Connection Diagram
Cable Recommendations
Source
Destination
8
2a. SATA Drive Interface
TC3-8 SATA
2b. IDE Drive Interface
TC6-8 IDE
3a. SATA Drive Power
TC5-8-R2 Drive Power
5a
2a
3a
3b. IDE Drive Power
TC2-8-R2 Drive Power
4a
4a/4b. SATA Drive
Interface
TC4-8-R2 (Unified)
3b
5b
2b
1
5a/5b. SATA Drive Power
TC4-8-R2 (Unified)
4b
6. USB 2.0 Ports (2x)
7
8. Power (DC In)
TP4 Power Supply
SAS and USB Protocol
Modules are now available. Visit
[Link]/tdp for
more information.
Note: When imaging 1.8 and
2.5 notebook or 1.8 ZIF IDE
drives, please use the properly
sized Tableau drive adapter
andTC6-2 IDE Signal Cable.
Note: Use cable TC3-9-1M
when imaging to the Tableau
TMSS Storage Systems.
7. FireWire 400 Port
TC7-6-6 1394A
(2x)
Step-by-Step Installation
1. Membrane Power Switch
Confirm TD2 is OFF
2a./2b. Source Drive Interface
Connect IDE or SATA source
drive to TD2
3a./3b. Source Drive Power
Connect IDE or SATA to TD2
source drive power
4a./4b. SATA Destination Drive Interface
Connect TD2 to SATA
destination drive(s)
6. USB 2.0 Port
Save logs to a USB storage
device and/or use duplicator
with a USB keyboard (optional)
7. FireWire 400 Port
Connect TD2 to external computer for
firmware updates (via Tableau firmware
update utility) as necessary
8. Power (DC In)
Connect TP4 power supply to TD2 DC In
Powering on the TD2: Power on the TD2,
source drive, and destination drive by pressing
the TD2 membrane power switch.
Setup Wizard: Upon initial startup, the user
will be prompted to configure the TD2. These
settings will be saved for future duplications.
One Button Duplication: Follow
instructions to connect drives and power-on
the TD2. Press the start button to verify
destination drive against presets and
initiate duplication.
5a./5b. SATA Destination Drive Power
Connect TD2 to SATA
destination drive power
LED Indicators
DC Power In
Power available at
power source
IDE or SATA
Source Detect
Flashing illumination:
Detecting IDE or
SATA source drive
Steady illumination:
IDE or SATA source
drive detected
Power
Duplicator turned ON
TD2 Menu Options
SATA Destination
1&2 Detect
Flashing illumination:
Detecting IDE or SATA
destination drive
Steady illumination:
IDE or SATA destination
drive detected
Alert
Flashing illumination:
Activity paused, user
response required
Steady illumination:
Read/write failure
encountered
Busy
Source or destination
drive activity
For the TD2 Users Guide and additional product information, visit [Link]/td2.
Guidance Software
W223 N608 Saratoga Drive
Waukesha, WI 53186
Toll Free: 1 (866) 973-6577
Main: 1 (626) 229-9191
[Link]
Duplicate Disk *
Disk-to-Disk
Disk-to-File
Format (FAT32)
Format Destination
Format USB
Wipe Disk
(Destination Only)
One-Pass Write
Multi-Pass Write
Hash Utilities
Source
(MD-5 & SHA-1)
Blank Check
Source Disk
Destination 1 Disk
Destination 2 Disk
Disk Information
Source Disk
Destination 1 Disk
Destination 2 Disk
Disk Utilities
Remove DCO & HPA
Remove HPA
Logs
View Logs
Save All Logs
Print All Logs
Erase Logs
Setup
System Options
Imaging Options
TD2 Options
Factory Reset
* Image verification enabled by default.
2012 Guidance Software, Inc. All Rights Reserved. EnCase and Guidance Software are registered trademarks or trademarks owned by Guidance
Software in the United States and other jurisdictions and may not be used without prior written permission. All other marks and brands may be
claimed as the property of their respective owners. Updated 11-2012.
