Count/Rate Controls “Syrelec Count/Rate Controls 13026 SERIES LCD UP/DOWN COUNTER, BATCH COUNTER CHRONOMETER AND RATEMETER * LCD Display with Back Light sized (72 x 72 mm) * Dual Preset or Single Preset plus Batch * Builtin Prescaler * Relay and Solid State Outputs * Built-in Sensor Supply * Lockout function GENERAL FEATURES ‘Output re spews Tipaeemrerrartarnptmcemtor, leas tS tan peep peeking a ee nptores ell ecu ee Cao Seanectsererremaeme | ET soon Site eaiareaGeRCe eta ANT ieimeramenn Me omacememmenanrencns Sot oan Eikloniia erietateaaetonee oer! cme conmutaancion a eamate SPECIFICATIONS: coming epeins entre pene vont Se anovicwsuavicn avast, Sone SEN EE Tet porcomain ——_sovaarne wo we coco romano ss igoenlSeyumees §——_conwecTions Inputs: Sourcing (NPN) oF sinking (PNP) Terminal meme, amen, | Me mca. Input maximum speed oh Level: 40 30 VDG Max #8: Reset input #13: Output il Relay, NO- Mode Single Cycle Repeat Cycle #8: Bloput #814: Output l Relay, NC = wo Mente ai ne oe Be ne an Terie onutin mes ES Gn — wt soi Mode ‘Atmput input EREJENCIEAC IEA] See. eo 8 ™ volageertonpane (els frolrsfrahss|sa]is]reh17] roca For Assistance Call 1 (800) 677-5311 155Port metal Stole) Count/Rate Controls 9 ssyrelec Count/Rate Controls DIP SWITCH SETTING 4}3)2\1 ~ oven «2 ff mop pe OFF: Programmer Mode 3 | 2 | Function ON | ON | Chronometer OFF | ON | Tachometer ON | OFF | Batch counter OFF | OFF | Counter | PROGRAMMING JAOB4B: | : AR8888 Bi | CHRONOMETER MODE 1) Programming Mode: Dip Switch #1 is OFF _ Press SEL] key to go to Stat/Stop input mode. Press (CHECK to move to the desired input mode. See Table | or Star’Stop options. - Pes again tomove tent Sead ode, Pres CHEGK ta ches beter i pst or. Yow send) = Press |SEL| key to go to the Time Range selection. Press [CHECK] to skroll through the different ranges. «Press |SELIkey again 0 goto the Output made. The ON time for the relay ouput can be programmed (up to 99 sec) by entering the time via the numeri Keyboard ~ Press [SEL t0 90 tothe Output Il mode. Proceed as for Output | { Press [SEL Key t0 90 tothe secure mode. Press [CHECK to select parameters (Preset I, Prese Il, Reset) secure. When parameter is selected, press [ON key to secure it or OFF key to not secure it - Press SEL) to goto Preset mode. Enter Preset | valve withthe numeric Keyboard. To enter 128 as a preset value, press [1] and (8) key Press SEL| to go to Preset Il and repeat the same operation as for Preset | Press SEL. , press ENT) and then A] key to end programming key Note: The programming mode can be ended at any time by pressing the ENT key. 2)User Modo: Dip Switch #1 is ON. In this mode the user will only be allowed to change parameters which have not been secured. 156 For Assistance Call 1 (800) 677-5311Count/Rate Controls -syrelec Count/Rate Controls COUNTER MODE 1)Programming Mode: Dip Switch #1 is OFF. _ = Press: seu key to go to the Input mode. Press [CHECK] to choose the desired input mode. ~ Press [SEL again to move to the Input speed mode. Press to choose between H (High Speed) or L (Low Speed). ~ Press [SE{! 10 g0 to the counting mode. Press CHECK) to select Preset to zero () or zoro to Preset (1). (Dir mode ony) ~ Press [SEL] to go to the Output | mode. Press (CHECK |to select the desired Output mode. The ON time of the relay output can be programmed (up to 9.9 sec) via the numeric keyboard. Press (SEL, to go tothe Output ll mode, Proceed as for Output | Press key to set the decimal point location. Press [CHECK] to move the decimal point to the desired position. ~ Press [SEL key to go tothe secure made. Press [CHECK to selec the parameters (Preset |, Preset Il, Reset, Coe to secure. When parameter is selected, press (ON) key o secure it or [OFF key to leave un-secured. Press ‘SEL, to go o preset mode. Enter Preset | valve va the numeric keyboard Press |SEL| to enter Preset Il value. Enter value via numeric keyboard. ~ Press [SEL to go tothe Prescalor factor (Coe). Entor valve via the keyboard. = Press (SEL, press [ENT and to end programming mode. 2)User Mode: Dip Switch #1 is ON ~ In this mode the user will only be allowed to change parameters which have not been secured, Table I: Input and Output Options Dieter se olor amen — 7 Yeates LUTE fo re jer} om) suet ELELELE wo lames TY, @lours T7-+0] opt . one lors Joma, @lowrn Tee foun —_ leur © fourm Tine jonah | ost pat Sop pt eet ipa nanemennos et anor Donn Wiesner Dov sen eet For Assistance Call 1 (800) 677-5311 187Ettore) Count/Rate Controls ssyrelec Count/Rate Controls ‘TACHOMETER MODE 1) Programming Mode: Dip Switch #1 is OFF. Press [SEL Key to select the Readout ode. Pross to soloct APS or RPM. The unit measures the period or time between input signals (1/T). Therefore to adjust the unit to the application, it is required to specily a “refreshment” time (tr), time between display updates and to specify a “limit” time (U), time after which, if there is no input pulse received, the speed will be considered as 2000. Press [SEL] key to enter the “refreshment time (tf). Enter the desired value via the numeric keyboard. - Press ‘key to enter the “limit” time (tl). Enter the desired value via numeric keyboard. For direc reading purposes, the number of pulses per revolution received by the tachometer can be programmed. Press enter the number of pulses per revolution Press SEL] to program the decimal point position, press [CHECK to move the decimal point to the desired position. ~ Press SEL, key to goto the secure mode. Press (CHECK to select the parameter (Preset |, Presa Il, Reset, Coe!) to secure. When parameters selected, press ON key 19 secure it or [OFF key to leave un-secured - Press SEL to goto preset mode. Enter Preset | value via the numeri keyboard ~ Press SEL to goto Preset I and enter value via the numeric Keyboard ~ Press (SEL to go to the Prescaler factor (coef). Enter value via the keyboard. ~ Press SEL), press [ENT] and Fito end programming mode. and 2}User Mode: Dip Switch #1 is ON ~ In this mode the user will only be allowed to change parameters which have not been secured. COUNTER & BATCH MODE 1)Programming Mode: Dip Switch #1 is OFF. "Press SEL Key to go to tne Input move. Press [CHECK to choose the desired input mode, ~ Press ‘again to move to the Input speed mode. Press (CHECK) to choose between H (High Speed) or L (Low Speed). ~ Press SEL, to g0 othe Output | mode. Press 10 select the desired Output rode. The ON time ofthe relay output can be programmed (up to 9.9 sec) by entering the time via the numeric keyboard. See Tabla | for Output mode selection. = Press SEL to go to the Output II mode. Proceed as for Output I. = Pres SEL ky sete cota pai ocaton. Press CHECK o mov he decinalpin othe ere pstion ~ Press |SEL| key to go to the secure mode. Press [CHECK to select the parameters (Preset |, Preset II, Rest, Coef} to secure. When parameters selected, press [ON] key to secure itor OFFkey to leave unsecured. Press [SEL to goto preset mode. Enter Batch preset value va the numeric Keyboard ~ Press [SEL to enter Preset Ii value. Enter value via numeric keyboard. ~ Press [SEL] to go to the Prescaler factor (Coe!) Enter value via the keyboard, ~ Press [SEL , press ENT; and [A to end programming mode. 2)User Mode: Dip Switch #1 is ON In this mode the user will only be allowed to change parameters which have not been secured. 'Note: In Batch Counter Mode the Output I is setup in repeat cycle mode. When the Preset Ils reached the Batch counter will be incremented by 1. Output It will tum ON, when the Batch Preset will be reached. 158 For Assistance Call 1 (800) 677-5311Count/Rate Controls Syrelec Count/Rate Controls DIMENSIONS: ORDERING INFORMATION: 13026 ‘SERIES 7 SERIES "9026 vw INPUT POWER INPUT POWER va: 115230 vac v2: 24/48 VAC va: 12124 VOC 232 ‘OPTIONS NX ‘OPTIONS 230-8 2320 422: AS 422 and 485, For Assistance Call 1 (800) 677-5311 159 Cr Eee tier)