Intelligent Hybrid System
Key Telephone
Quick Reference Guide
Before using Your Telephone
Thank you for purchasing NEC Infrontia Aspila Topaz system.
Due to the flexibility built into the system, your Dialing Codes and Feature Capacities may differ from those
in this guide. Check with your Supplier / System Administrator and make a note of any differences.
Using Your Telephone
< Key Telephone>
Alphanumeric Display
Handset
Indicator
CHECK Key
CLEAR Key
Programmable Function Keys
LND (Last Number Dial) Key
OPAC (Operation Access) Key
DC (Dial Control) Key
CALL Key
FLASH Key
TRFR (Transfer) Key
SPK (Speaker) Key
DND/CONF Key
(Do Not Disturb / Conference)
HOLD Key
Microphone
MIC (Microphone) Key
Speaker
Dial Keys
VOL (Volume Control) Key
Functions
12TXD
12TD
6TXD
6TD
Programmable Keys
Additional Prg. Keys
Display
CHECK/CLEAR Keys
Handsfree
Accept DLS Console
Wall Mount Kit
12
10
Yes
Yes
Yes
Yes
Yes (Built-in)
12
10
No
No
No (Talkback)
No
Yes (Built-in)
6
10
Yes
Yes
Yes
Yes
Yes (Built-in)
6
10
No
No
No (Talkback)
No
Yes (Built-in)
Handsfree Options
- Handsfree lets you place and answer calls by pressing SPK instead of using the handset.
- With Automatic Handsfree, you can press a CALL Key without lifting the handset. Normally, you have
Automatic Handsfree.
- Use Handsfree Answerback to answer a voice-announced Intercom call by speaking toward your phone
without lifting the handset.
For Your Convenience
Program Function Keys
Programmable Function Keys can be assigned as Trunk Key and/or other Function Keys. You can just press
the function key to activate the assigned function without dialing the Service Code.
CALL
Function Key
Code + Additional Data
SPK
There are 2 levels of Function Keys. (General Keys : assigned by 851, Appearance Keys : assigned by 852)
Appearance Keys have priority. You can overwrite the Appearance Key at the General Key.
If you want to overwrite the General Key at the Appearance Key, you have to erase the Appearance Key by
dialing 852 + 000 before General Key assignment.
In the default setting, Programmable Function Key No. 1 to 12 is assigned as Trunk Key. If you want to
assign Function Keys (General) at the unused Trunk Keys, these unused keys should be erased by 852 +
000 operation.
Programmable Function Keys can be erased by dialing 852 + 000 or 851 + 00.
Program DSS/One-Touch Keys
Programmable Function Keys can be assigned as DSS (Direct Station Selection) or One-Touch Keys. You can
place an Outside / Intercom Call just pressing this key without dialing the number.
CALL
Function Key
Telephone Number
0
HOLD
SPK
Extension Number
In the default setting, Programmable Function Key No. 1 to 12 is assigned as Trunk Key. If you want to
assign DSS Keys at the unused Trunk Keys, these unused keys should be erased by 852 + 000
operation before the above operation.
In case of DSS Key, the extension status can be indicated on the BLF. (idle : extinguished, Busy : lit)
When you register a telephone number, 9 (Trunk Access Code) should be added on top of number.
Up to 24 digits dialing can be registered, but the name can not be registered.
If you want to continue the operation, press Programmable Function Key instead of SPK Key to finish.
For Your Convenience
Register Abbreviated Dialing <Display Key Telephone>
(Common ABB)
CALL
Bin No.
Telephone Number
(Group ABB)
4
Name
HOLD
HOLD
SPK
The digit of Bin No. depends on the system setting. (0-9 / 00-99 / 000-999)
System setting is necessary for Group ABB function. Ask your Supplier for more details.
Name can be entered by Dial Pad Keys. (See below)
Up to 24 digits dialing can be registered, and up to 12 characters can be registered as name.
If you want to continue the operation, dial Bin No. instead of SPK Key to finish.
You can skip to enter the name. (No enter any character, then press HOLD Key).
You can erase the registered number & name by pressing CLEAR Key after dialing Bin No..
Entering Alphanumeric Characters
When you enter a name, use Dial Pad Keys to enter letters as below. For example, press 2 key once for A,
twice for B, etc
Number of pressing the Key
1
10
11
&
<
#
DND/CONF
>
12
13
Accepts a character and move the cursor one place to the right. Press twice to insert a space.
Clear the character entry to the left, one character at a time. (Backspace Key)
Placing Calls
Place an Outside Call <Quick Access>
Trunk Key
Telephone Number
Listen for Dial Tone before dialing a Telephone Number.
You can have function keys for Trunks or Trunk Groups. Ask your Supplier.
Place an Outside Call <Access by Code>
Telephone Number
CALL
Trunk Group No.
?
Trunk No. (e.g. Trunk 5)
Listen for Dial Tone before dialing a Telephone Number.
In case the number of Trunk Group is more than 10, you should enter 2 digits (e.g. 05 : Group 5) after
dialing 804. Ask your Supplier more details.
Place an Intercom Call <Dial Access>
CALL
Extension Number
Pressing CALL key after dialing an extension number is also possible.
Your call will ring or voice-announce. If you hear ringing, wait for an answer. If you hear a beep, begin
speaking. Dialing 1 changes voice/ring mode. (in case the destination is Key Telephone)
Placing Calls Quickly
Abbreviated Dialing <for Outside>
Common
ABB
Group
ABB
CALL
Common ABB Bin No.
DC
?
Group ABB Bin No.
CALL
Group ABB Key
(851+28)
The digit of Bin No. depends on the system setting. (0-9 / 00-99 / 000-999)
Telephone Numbers shall be pre-registered to the system.
System setting is necessary for Group ABB function. Ask your Supplier for more details.
One-Touch Call <for Outside / Intercom>
One-Touch / DSS Key
The Telephone / Extension Number shall be pre-registered to a One-Touch / DSS Key. (Refer to P.2)
Trunk Access Code (Dial 9) should be added on top of Telephone Number.
Last Number Dialing <for Outside / Intercom>
CALL
Redial List
LND
The system retains the last 10 numbers dialed which can be viewed and dialed.
(For Display Key Telephone)
LND
(On-Hook)
VOL
(Find desired number)
Intercom Number can also be stored to LND. (System setting is necessary. Ask your Supplier.)
If your call doesnt go through
Set Camp On / Callback
8
(Hear Busy Tone
or No Answer)
Camp On Key
<Camp On>
Wait without
hanging up
<Callback>
Wait for the
system to call
you back
(851+35)
<Camp On> In case of Intercom Call, when you hear ringing, wait for the called party to answer.
In case of Outside Call, when you hear Dial Tone, begin telephone number dialing.
<Callback> In case of Intercom Call, when your phone starts the ringing, lift handset and wait for the
called party to answer.
In case of Outside Call, when your phone starts the ringing, lift handset, hear Dial Tone, and
begin telephone number dialing.
This function is applicable in case all trunks are busy condition. (not applicable for dialed outside party busy)
Cancel Camp On / Callback
8
(In case of Camp On)
Set / Answer a Message Waiting
Set
MW Key
(Hear Busy Tone
or No Answer)
(851+38)
Answer
Your phones
Indicator is
flashing in Red
MW Key
(851+38)
When you set a MW, the called partys Indicator starts to flash, and your Indicator is lit in Red.
When you answer a MW, the Indicator shall automatically be off when the called party answers.
If your call doesnt go through
Check & Answer a Message Waiting <Display Key Telephone>
You can check who left a message to you, and then answer.
CHECK
VOL
1
(Check Name)
(On-Hook)
Cancel Message Waiting (Cancel Individually - at originated extension)
Extension Number
you want to cancel MW
CALL
SPK
Clear all Message Waiting (at any extension)
CALL
SPK
Clear all messages (you have left for other extensions and messages other extension have left for you).
Repeat Dialing <Outside Call>
DC
(Hear Busy Tone
or No answer)
LND
Repeat Dial Key
(851+29)
The system periodically redials the call. Repeat duration is programmable. Ask your Supplier.
You should lift the handset when the called party answered.
You can cancel this function by pressing DC and LND during idle condition.
Answering Calls
Answering an Outside Call
Ringing
Extension
Trunk Key
Non-Ringing
Extension
(Ringing)
(Flashing)
SPK
SPK
Confirm the status of MIC Key if you want to answer by Handsfree. (MIC On : Light off, MIC Off : Light On)
Answering an Intercom Call
Voice Mode
Extension
Ring Mode
Extension
(Voice)
(Ringing)
Speak toward
your phone
SPK
Intercom Call Mode can be set at your phone by : Ring : CALL + 823 Voice : CALL + 821
Confirm the status of MIC Key if you want to answer by Handsfree. (MIC On : Light off, MIC Off : Light On)
Picking up a call for other Extensions
In same
Group
CALL
Call Pickup Key
(851+24)
In other
Groups
CALL
Call Pickup for other Group Key
(851+25)
Pickup for
Specified
Extension
Extension Number
CALL
System setting is necessary to make Call Pickup Group. Ask your Supplier.
Hold / Transferring Calls
Holding a Call / Retrieving a Held Call
Hold
Trunk Key
Retrieve
(Flashing)
HOLD
CALL
(Talking)
(Flashing)
In case of Intercom, the call shall be held as Exclusive Hold on your phone.
This operation puts your outside call on System Hold. Other extension user can take the call off Hold.
Holding a Call Exclusively
Hold
Trunk Key
Retrieve
Exclusive Hold Key
(Flashing)
CALL
(851+45)
(Talking)
(Flashing)
System setting is necessary to use Exclusive Hold. Ask your Supplier.
This operation puts your outside call on Exclusive Hold. Other extension user can not take the call off Hold.
Retrieve a held outside call (if your extension doesnt have Trunk Keys)
Trunk No. you want to retrieve
CALL1
TRFR
(To answer own held Trunk)
Transferring a Call to the other Extension
HOLD
Extension Number
(Talking)
(Announce)
TRFR
If your phone has DSS or One-Touch key, just press it instead of HOLD and Extension Number operation.
For more convenient use
Do Not Disturb (DND)
DND/CONF
(On-Hook)
DND : Trunk Incoming Call
DND : Intercom Incoming Call
DND : Trunk & Intercom Incoming Call
DND : Transferred (CFW) Call
DND : Cancel
When you set DND function, DND/CONF Keys lamp is lit and the Internal Dial Tone pattern is changed.
Call Forwarding / Follow Me
CFW Condition
CALL
Extension Number
CFW Type
SPK
When Busy / No Answer
When No Answer
FWD All Calls
Follow Me
Both Ring
FWD Outside Calls only
Immediate
Cancel
FWD Intercom Calls only
When you set Call Forwarding function, DND/CONF Keys lamp flashes and Internal Dial Tone pattern is
changed.
Conference
DND/CONF
Extension Number
?
(Talking)
Trunk Key
DND/CONF
?
Telephone Number
You can repeat this operation to add more parties.
You may be able to have up to 8 parties. (include your extension)
10
(Talk)
<twice>
Nothing contained in this manual shall be deemed to be, and this manual does not constitute, a warranty of, or representation
with respect to, any of the equipment covered. This manual is subject to change without notice and NEC Infrontia Asia Pacific
Sdn Bhd has no obligation to provide any updates or corrections to this manual. Further, NEC Infrontia Asia Pacific Sdn Bhd
also reserves the right, without prior notice, to make changes in equipment design or components as it deems appropriate. No
representation is made that this manual is complete or accurate in all respects and NEC Infrontia Asia Pacific Sdn Bhd shall
not be liable for any errors or omissions. In no event shall NEC Infrontia Asia Pacific Sdn Bhd be liable for any incidental or
consequential damages in connection with the use of this manual. This document contains proprietary information that is
protected by copyright. All rights are reserved. No part of this document may be photocopied or reproduced without prior
written consent of NEC Infrontia Asia Pacific Sdn Bhd.
2004 - 2005 by NEC Infrontia Asia Pacific Sdn Bhd
Printed in Malaysia
All Rights Reserved.
Sales & Marketing Regional Head Office
NEC Infrontia Asia Pacific Sdn Bhd
Selangor Darul Ehsan, Malaysia
Issue 1-1
January, 2005
11
