Owners manual

Hearty welcome among Ducati fans! Please accept out

best compliments for choosing a Ducati motorcycle. We
think you will ride your Ducati motorcycle for long
journeys as well as short daily trips. Ducati Motor S.p.A.
wishes you smooth and enjoyable riding.
We are steadily doing our best to improve our Technical
Assistance service. For this reason, we recommend you
to strictly follow the indications given in this manual,
especially for motorcycle running-in. In this way, your
Ducati motorbike will surely give you unforgettable
emotions. For any servicing or suggestions you might
need, please contact our authorized service centers.

Ducati Motor S.p.A. declines any liability whatsoever for

any mistakes incurred in drawing up this manual. The
information contained herein is valid at the time of going
to print. Ducati Motor S.p.A. reserves the right to make
any changes required by the future development of the
above-mentioned products.

Enjoy your ride!

For your safety, as well as to preserve the warranty,
reliability and worth of your motorcycle, use original
Ducati spare parts only.
Warning
This manual forms an integral part of the
motorcycle and - if the motorcycle is resold - must
always be handed over to the new owner.

TABLE OF CONTENTS

Main components and devices

Location 19
Tank filler plug 20
Seat catch and helmet hooks 21
Side stand 22
Front fork adjusters 23
Shock absorber adjusters 24

General 6
Warranty 6
Symbols 6
Useful information for safe riding 7
Carrying the max load allowed 8
Identification data 9

Directions for use 26

Running-in recommendations 26
Pre-ride checks 27
Starting the engine 28
Moving off 30
Braking 30
Stopping the motorcycle 31
Parking 31
Refueling 32

Controls 10
Position of motorcycle controls 10
Instrument panel 11
Keys 12
Key-operated ignition switch and steering lock 12
Left switch 13
Clutch lever 14
Cold start lever 15
Right switch 15
Throttle twistgrip 16
Front brake lever 16
Rear brake pedal 17
Gear change pedal 17
Setting the gear change and rear brake pedals 18

19

Maintenance 33
Tool kit and accessories 33
Routine maintenance 34
Main maintenance operations 37
Removing the fairing 37
Lifting the fuel tank 40
Changing the air filter 41
Checking brake and clutch fluid level 42
Checking brake pads for wear 43
Lubricating cables and joints 44
Throttle cable adjustment 45
Checking battery electrolyte level 46

Charging the battery 47

Chain adjustment 48
Chain lubrication 49
Replacing bulbs 50
Beam setting 54
Tyre pressures 55
Checking engine oil level 57
Cleaning and replacing the spark plugs 58
Cleaning the motorcycle 59
Storing the bike away 59
Important notes 59

Technical data 60
Overall dimensions 60
Weights 60
Top-ups 61
Engine 62
Timing system 62
Performance data 63
Spark plugs 63
Brakes 64
Transmission 65
Frame 66
Wheels 66
Tyres 67
Suspensions 67
Electric system 68
For united states of america version only
Routine maintenance record

72

81
5

GENERAL

Warranty
In your own interest, and in order to guarantee product
reliability, you are strongly advised to refer to our
authorized Dealers and workshops for any servicing
requiring particular technical expertise. Our highly skilled
staff have access to the implements required to perform
any servicing job at best, and use Ducati original spare
parts only as the best guarantee for full
interchangeability, smooth running and long life.
All Ducati motorcycles come with a Warranty Card.
However, warranty does not apply to the motorcycles
used in competitions or competitive trials. No motorcycle
part may be tampered with, altered, or replaced with
parts other than original Ducati spare parts during the
warranty period, or the warranty will be automatically
invalidated.

Symbols
Ducati Motor S.p.A. advises you to read this booklet
carefully so as to become familiar with your motorcycle.
In case of any doubts, please call a Ducati dealer or
authorized workshop. The information contained herein
will prove useful on your trips - and Ducati Motor S.p.A.
wishes you smooth, enjoyable riding - and will help you
keep the performance of your motorcycle unchanged for
a long time.
Warning
Failure to comply with these instructions may put you at
risk and lead to severe injury or death.
Important
Possibility of damaging the motorcycle and/or its
components.
Note
Additional information concerning the job being carried
out.
The terms right and left are referred to the motorcycle
viewed from the riding position.

Useful information for safe riding

Warning
Read this section before riding your motorcycle.
Accidents are frequently due to inexperience. Always
make sure you have your licence with you when riding;
you need a valid licence to be entitled to ride your
motorcycle.
Do not lend your motorcycle to inexperienced riders or
who do not hold a valid licence.
Both rider and pillion passenger must always wear a
safety helmet.
Wear proper clothing, with no loose items or accessories
that may become tangled in the controls or limit your
zone of vision.
Never start or run the engine indoors. Exhaust gases are
poisonous and may lead to loss of consciousness or even
death within a short time.
Both rider and pillion passenger should keep their feet on
the footpegs when the motorcycle is in motion.
Always hold the handlebars firmly with both hands so
you will be ready for sudden changes of direction or in
the road surface. The pillion passenger should always
hold on to the suitable strap at the rear of the seat.
Ride within the law and observe national and local rules.
Always respect speed limits where these are posted.
However, always adjust your speed to the visibility, road
and traffic conditions you are riding in.
Always signal your intention to turn or pull to the next

lane in good time using the suitable turn indicators.

Be sure you are clearly visible and do not ride within the
blind spot of vehicles ahead.
Be very careful when tackling road junctions, or when
riding in the areas near exits from private grounds, car
parks or on slip roads to access motorways.
Always turn off the engine when refueling.
Be extremely careful not to spill gasoline on the engine
or on the exhaust pipe when refueling.
Do not smoke when refueling.
While refueling, you may inhale noxious gasoline vapors.
Should any gasoline drops be spilled on your skin or
clothing, immediately wash with soap and water and
change your clothing.
Always remove the key when you leave your motorcycle
unattended.
The engine, exhaust pipes, and mufflers stay hot for a
long time.
Park your motorcycle where no one is likely to hit it and
use the side stand.
Never park on uneven or soft ground or your motorcycle
may fall over.

Carrying the maximum load allowed

Your motorcycle is designed for long-distance riding,
carrying the maximum load allowed in full safety.
Even weight distribution is critical to preserving these
safety features and avoiding trouble when performing
sudden manoeuvres or riding on bumpy roads.

Information about carrying capacity

The total weight of the motorcycle in running order
including rider, pillion passenger, luggage and additional
accessories should not exceed
385 Kg/851 lb.
Arrange your luggage or heavy accessories in the lowest
possible position and close to motorcycle centre.
Be sure to secure the luggage to the supports provided
on the motorcycle as firmly as possible. Improperly
secured luggage may affect stability.
Never fix bulky or heavy objects to the handlebar or to
the front mud guard as this would affect stability and
cause danger.
Do not insert any objects you may need to carry into the
gaps of the frame as these may foul moving parts.
Make sure the tyres are inflated to the proper pressure
indicated at page 55 and that they are in good
condition.

Identification data
All Ducati motorcycles have two identification numbers,
for frame (fig. 1.1) and engine (fig. 1.2).
Frame number
Engine number

E
Note
These numbers identify the motorcycle model and
should always be indicated when ordering spare parts.
fig. 1.1

fig. 1.2
9

CONTROLS

3
6

Warning
This section details the position and function of all
the controls you need to drive your motorcycle. Be sure
to read this information carefully before you use the
controls.

4
5

Position of motorcycle controls (fig. 2)

1) Instrument panel.
2) Key-operated ignition switch and steering lock.
3) Left switch.
4) Clutch lever.
5) Cold start lever.
6) Right switch.
7) Throttle twistgrip.
8) Front brake lever.
9) Gear change pedal.
10) Rear brake pedal.

8
7
2

9
10

fig. 2
10

Instrument panel (fig. 3)

1) Speedometer (km/h or mph).
Gives road speed.
a) Odometer (km or miles).
Gives total distance covered.
b) Trip meter (km or miles).
Gives distance covered since last resetting.
c) Trip meter resetting knob.
Turn to reset trip meter to 0000.
2) Engine revolution meter (rpm)
Indicates engine rpm.
3) Green light N.
Comes on when gearbox is in neutral.
4) Yellow light .
Comes on when there are about 4 liters/1.05 US Gall.
fuel left in the tank.
5) Green light
.
Comes on and flashes when a turn indicator is on.
6) Red light
.
Comes on when engine oil pressure is too low. It briefly
comes on when the ignition is switched to ON and
normally goes out a few seconds after engine starts.
Important
If this light stays on, stop the engine or it may
suffer severe damage.

Important
Stop the engine if it reaches maximum temperature
or it may suffer severe damage.
When you switch on the parking light, the panel lights
will come on as well.

1
b

8
7

10
11

6
160 180 200
140
220
120
240
120
260
80

5
4
3
2

MIN -1

X1000

Km/h

60
40
20

7) Blue light
.
Comes on when high beam is on.
8) Oil temperature indicator.
Shows temperature of engine oil.

LO

HI

fig. 3
11

Keys (fig. 4)
Your Ducati was delivered with two universal keys for
ignition, steering lock and seat catch and a key
identification plate (1).
Note
Separate the two keys and keep the identification
plate in a safe place.

Key-operated ignition switch and steering lock

(fig. 5)
It is located in front of the fuel tank and has four
positions:
A) ON: lights and engine on;
B) OFF: lights and engine off;
C) LOCK: steering locked;
D) P: parking light and steering lock.
Note
To move the key to the last two positions, press it
down before turning it. Switching to (B), (C) and (D), you
will be able to take the key out.

fig. 4
12

fig. 5

Left switch (fig. 6)

1) Switch, light switch, 3 positions:
Down
= lights off;
Centre
= front and rear parking light, number plate
light and panel lights on;
Up = headlamp, front and rear parking light, number
plate light and panel lights on.
Note
This device is not fitted on the Australia and Japan
versions.
2) Dip switch, light dip switch, two positions:
position
= low beam on;
position
= high beam on.

fig. 6

3) Switch
= 3-position turn indicator:
centre position = OFF;
position = left turn;
position = right turn.
To cancel turn indicators, return switch to central position
and push in.
4) Button

= warning horn.

5) Button

= high-beam flasher.

13

Clutch lever (fig. 7)

Lever (1) disengages the clutch. It features a dial adjuster
(2) for lever distance from the twistgrip on handlebar.
To set lever distance from twistgrip, push lever (1) fully
forward and turn the dial adjuster (2) to one of its four
positions. Remember that position no. 1 gives maximum
distance between lever and twistgrip, whereas lever and
twistgrip are closest when adjuster is set to position no.
4.
When you pull in the lever (1), you will disengage the
engine from the gearbox and therefore from the driving
wheel. Using the clutch properly is essential to smooth
riding, especially when moving off.
Warning
Set clutch lever when motorcycle is stopped.
Important
Using the clutch properly will avoid damage to
transmission parts and spare the engine.

14

fig. 7

Cold start lever (fig. 8)

Use this device to start the engine from cold. It will
increase the engine idling speed after starting.
Lever positions:
A) (vertical) = closed
B) fully open.
The lever can be opened and closed gradually to adjust
speed until engine is fully warm (see page 28).
Important
Never use the cold start device when the engine is
warm or leave it open when riding.

Right switch (fig. 9)

G) Switch for ENGINE STOP, two positions:
position
(RUN) = run.
position
(OFF) = stop.
Warning
This switch is mainly intended for use in emergency
cases when you need to stop the engine quickly. After
stopping the engine, return the switch to the
position
to enable starting.
Important
Stopping the engine using switch (1) when riding
with the lights on and leaving the ignition key in the ON
position, may run the battery flat as the lights will remain
on.
2) Button

= engine start

fig. 8
15

Throttle twistgrip (fig. 9)

The twistgrip (3) on the right handlebar opens the
throttles. When released, it will spring back to the initial
position (idling speed).

fig. 9
Front brake lever (fig. 9)
Pull in the lever (4) towards the twistgrip to operate the
front brake. The system is hydraulically operated and you
just need to pull the lever gently.
The control lever features a dial adjuster (5) for lever
distance from the twistgrip on handlebar.
Warning
Please read the instructions on pages 28 / 30
before using these controls.

16

Rear brake pedal (fig. 10)

Push down on the pedal (1) to apply the rear brake. The
system is hydraulically operated.

Gear change pedal (fig. 11.1)

The gear change pedal is at rest when in the central
position N, is moved up and down to change gears and
then returns to the central position.
down = push down on the pedal to engage 1st gear and
to shift down. The N light will go out.
up = lift the pedal to engage the 2nd gear and then the
3rd, 4th, 5th and 6th gear (6th gear: 900 only).
Each time you move the pedal you will engage the next
gear.

1
fig. 10

fig. 11.1
17

Setting the gear change and rear brake pedals

The gear change and rear brake pedals can be adjusted
to suit the preferred riding position of each rider.
To set the gear change pedal,
lock linkage (1) and loosen the check nuts (2) and (3).
Note
Nut (2) has a left-hand thread.

Apply an open-end wrench to the hexagon end of linkage

(1) and rotate linkage until setting pedal in the desired
position.
Tighten both check nuts onto linkage.
To set the rear brake pedal,
loosen check nut (4).
Turn pedal travel adjusting screw (5) until pedal is in the
desired position.
Tightenloosen check nut (4).
Work pedal by hand to make sure it has 1.5 - 2
mm/0.059-0.078 in. free play before brake begins to bite.
If not so, set the length of pump linkage as follows.
Loosen the check nut (6) on pump linkage.
Tighten linkage into fork (7) to increase play, or unscrew
linkage to reduce it.
Tighten check nut (6) and check pedal free play again.

fig. 11.2

fig. 11.3
18

MAIN COMPONENTS AND DEVICES

Location (fig. 12)

1) Tank filler plug.
2) Seat catch and helmet hooks.
3) Side stand.
4) Rear view mirrors.
5) Front fork adjusters (900).
6) Shock absorber adjusters.

E
4
5

2
6

5
3

fig. 12
19

Tank filler plug (fig. 13)

Opening
Lift the protection lid (1) and fit the ignition key into the
lock. Turn the key clockwise 1/4 turn to unlock. Lift the
plug.

Closing
Refit the plug with the key in it and push it down into its
seat.
Turn the key anticlockwise to its initial position and take it
out. Close the lock protection lid (1).
Note
The plug can only be closed with the key in. In turn,
the key can only be taken out after the plug has been
closed.
Warning
Always make sure you have properly refitted (see
page 32) and closed the plug after each refueling.

20

1/4
OPEN

fig. 13

Seat catch and helmet hooks

Opening (fig. 14.1)

Fit the ignition key into the lock (1) and turn the key
clockwise until the rear end of the seat lifts up. Pull the
seat backwards to slide it off its front holders.
At the front end of the compartment underneath the
seat, there are the helmet hooks (2, fig. 14.2) for rider
and pillion rider helmets. Hook the helmet straps onto
the hooks and leave the helmets hanging outside. They
will be locked safely when you refit the seat.

0 O
PE
1

Warning
This system is intended to lock your helmet safely
when you park your motorcycle. Never leave the helmet
hanging from the hook when riding or it may get in the
way and make you lose control of the motorcycle.
Closing
Make sure that all parts are arranged and secured
properly inside the compartment under the seat. Slide
the front ends of the seat bottom underneath the frame
U-bolt and push down on the rear end of the seat until
you hear the catch click. Make sure the seat is firmly
secured to the frame and take the key out of the lock (1).

fig. 14.1

fig. 14.2
21

Side stand (fig. 15)

Important
Before lowering the side stand, make sure that the
bearing surface is hard and flat.

Warning
The motorcycle can only be started if the side stand
is in rest position as it is equipped with a safety device
that prevents engine start when stand is down.

Do not park on soft or pebbled ground or on asphalt melt

by the sun heat and similar or the motorcycle may fall
over.
When parking in downhill road tracts, always park the
motorcycle with its rear wheel facing downhill.
To pull down the side stand, hold the motorcycle
handlebars with both hands and push down on the stand
(1) with your foot until it is fully extended. Tilt the
motorcycle until the side stand is resting on the ground.
Warning
Do not sit on the motorcycle when it is supported
on the side stand.
To move the side stand to its rest position (horizontal
position), tilt the motorcycle to the right and, at the same
time, lift the stand (1) with your foot.
Note
Check for proper operation of the stand mechanism
(two springs, one into the other) and the safety sensor (2)
at regular intervals.

1
fig. 15

22

Front fork adjusters

The front fork used on the 900 model has rebound and
compression damping adjusters.
This adjustment is done using the outer adjusters:
1) (fig. 16.1) to adjust rebound damping;
2) (fig. 16.1) to adjust inner springs preload;
3) (fig. 16.2) to adjust compression damping.
Turn the adjuster (1) on fork leg top with a flat
screwdriver to adjust rebound damping.
To reach the adjuster (3), insert a screwdriver into the
passing hole on the wheel spindle at fork leg axis.
As you turn the adjusting screws (1 and 3), you will hear
them click. Each click identifies a setting. Turn the screw
all the way in to set the hardest damping (position 0).
This will be your starting point. Now turn the screw
anticlockwise and listen for the clicks that identify setting
positions no.1, 2 and so on.
STANDARD factory setting is as follows:
compression: 11 clicks;
rebound: 7 clicks.
The setting range is 14 clicks for rebound and 16 clicks
for compression. The 14th and 16th clicks give the
softest damping. To change the preload of the spring
inside each fork leg turn the hex. adjusting nut (2) with a
22-mm hexagon wrench.
Height (A, fig. 16.1) determines preload and may vary
from 25/0.98 to 10 mm/0.39 in.
Factory setting is 18 mm/0.70 in.

fig. 16.1

fig. 16.2
23

900

Important
Adjust both fork legs to same settings.

Shock absorber adjusters (fig. 17.1)

The shock absorber has outer adjusters that enable you
to adjust your motorcycle to the load.
The adjuster (1) located on the left side on the
connection holding the shock absorber to the swingarm
controls rebound damping.
The adjuster (2) on the shock absorber expansion
reservoir on the left hand side of frame controls
compression damping.
Turning the adjusters (1 and 2) clockwise gives harder
damping H, turning anticlockwise gives softer damping
S.
STANDARD setting:
turn the adjusters (1 and 2) all the way in (clockwise) then
slacken them 1 turn.
The two ring nuts (3, fig. 17.2) located on the top section
of the shock absorber control outer spring preload.
To change spring preload, turn the upper ring nut. Then
turn the lower ring nut clockwise or anticlockwise to
increase or decrease spring preload as required.
STANDARD spring length: 176 mm/6.93 in.
Warning
Use a specific pin wrench only to turn the preload
adjusting ring nut. Be careful when turning the nut with
the wrench, as the pin may slip out of the nut recess and
you may hurt your hand hitting motorcycle parts.

24

The shock absorber is filled with gas under pressure and

may cause severe damage if taken apart by unskilled
persons.
When carrying a passenger and a load, set the rear shock
absorber spring to proper preload to improve motorcycle
handling and keep safe clearance from the ground. You
may find that rebound damping needs adjusting as well.

fig. 17.1

fig. 17.2
25

DIRECTIONS FOR USE

another and above all not to adversely affect the life of

basic engine parts, it is advisable to avoid harsh
accelerations and not to run the engine at high rpm for
too long, especially uphill.
Furthermore, the drive chain should be inspected
frequently. Lubricate and tighten chain as required.

Running-in recommendations

From 1000 to 2500 km/620 to 1550 miles

At this point, you can squeeze some more power out of
your engine, being careful, however, to never exceed
7000 rpm.

Max. rotation speed (fig. 18)

Rotation speeds (rpm) for running-in period and during
standard use
1) up to 1000 km/620 miles;
2) from 1000 to 2500 km/620 to 1550 miles;
3) after 2500 km/1550 miles.
Up to 1000 km/620 miles
During the first 1000 km/620 miles, keep an eye on the
revolution meter. The indicator must not exceed:
5500-6000 rpm.
During the first hours of riding, it is advisable to run the
engine at varying load and rpm, though still within
recommended limit.
To this end, roads with plenty of bends and even slightly
hilly areas are ideal for a most efficient running-in of
engine, brakes and suspensions.
For the first 100 km/62 miles, use the brakes gently. Do
not brake violently or keep brake applied for too long.
This will enable a correct break-in of friction material on
brake pads against brake discs.
For all mechanical parts of the motorcycle to adapt to one
26

Important
During the whole running-in period, the
maintenance and service rules recommended in this
manual should be observed carefully. Have the service
inspections performed as recommended in the Warranty
Card.
Failure to comply with these rules will release Ducati
Motor S.p.A. from any liability whatsoever for resulting
engine damage or shorter engine life.
After 2500 km/1550 miles
After running-in, never exceed the following values
during the motorcycle standard use:
8500 rpm (750);
7500 rpm (900).
Strict observance of running-in recommendations will
ensure longer engine life and reduce the likelihood of
overhauls and tune-ups.

Pre-ride checks

Brake and clutch fluid

Check fluid level in the relevant reservoirs.
Tyre condition
Check tyre pressure and condition (page 55).
Controls
Work the brake, clutch, throttle and gear change controls
(levers, pedals and twistgrips) and check for proper
operation.
Lights and indicators
Make sure lights, indicators and horn work properly.
Replace any burnt-out bulbs (page 50).
Key-operated locks
Check that fuel filler plug and seat catch locks are closed
firmly.
Stand
Make sure side stand operates smoothly and is in the
correct position (page 22).

Warning
Failure to carry out these checks before riding, may
lead to motorcycle damage and injury to rider and
passenger.

Warning
In case of malfunctioning, do not start the
motorcycle and call a Ducati Dealer or authorized
workshop.

fig. 18

Before riding, perform a thorough check-up on your bike

as follows:
Fuel level in the tank
Check fuel level in the tank.
Fill tank if needed (page 32).
Engine oil level
Check oil level in the sump through the sight glass. Top
up if needed (page 57).
27

Starting the engine

Note
Follow the High ambient temperature procedure
to start the engine when it is warm.

Important
Never operate the electric start button more than 5
seconds at a time. If needed, allow 10 seconds before
attempting to restart the engine.

Warning
Before starting the engine, become familiar with
the controls you will need to use when riding.

Regular ambient temperature

(10 to 35 C/50 to 95 F):
1) Move the ignition key to ON (fig. 19.1). Make sure
both the green light N and the red light
on the
instrument panel come on.
Important
The oil pressure light should go out a few seconds
after the engine has started (page 11).
Warning
The side stand must be fully up (in a horizontal
position) as its safety sensor prevents engine start when
down.
2) Move the cold start lever to the B position (fig. 19.2).
3) Check that the stop switch (1, fig. 19.3) is positioned
to (RUN), then press the starter button (2).
Let the engine start without using the throttle control.
fig. 19.1
28

4) Move the cold start lever to the vertical position (A) to

let engine idle at about 1400-1500 rpm.
Important
Do not rev up the engine when it is cold. Allow
some time for oil to reach all points that need lubricating.
5) As the engine warms up, move the cold start lever
gradually towards the vertical position (A). Once fully
warm, the engine should hold idling rpm with the cold
start shut down.
High ambient temperature (over 35 C/95 F):
Follow the same procedure, however, do not use the
cold start device.

fig. 19.2

Cold ambient temperature (below 10 C/50 F):

Follow the procedure for Regular ambient
temperature, however allow 5 minutes for the engine to
warm up (see step 5).

fig. 19.3
29

Moving off
1) Disengage the clutch squeezing the control lever.
2) Push down on gear change lever sharply with the tip
of your foot to engage the first gear.
3) Speed up engine, by turning the throttle twistgrip and
slightly releasing the clutch lever at the same time. The
motorcycle will start moving off.
4) Let go of clutch lever and speed up.
5) To shift up, close the throttle to slow down engine,
disengage the clutch, lift the gear change lever and let go
of clutch lever.
To shift down, release the twistgrip, pull the clutch
control lever, shortly speed up to help gears synchronize,
shift down and release the clutch.
The controls should be used correctly and timely: when
riding uphill do not hesitate to shift down as soon as the
motorcycle tends to slow down, so you will avoid
stressing the engine and the motorcycle abnormally.
Important
Avoid harsh accelerations, as this may lead to
carburettor flooding and transmission snatching. The
clutch lever should not be pulled longer than necessary
after gear is engaged, or friction parts may overheat and
wear out.

30

Braking
Slow down in time, shift down to engine-brake first and
then brake applying both brakes. Pull the clutch lever
before stopping the motorcycle, to avoid sudden engine
stop.
Warning
Use both brake lever and pedal for effective
braking. Using only one of the brakes will give you less
braking power.
Never use brake controls harshly or violently or you may
lock the wheels and lose control of the motorcycle.
When riding in the rain or on slippery surfaces, braking
will become less effective. Always use the brakes very
gently and carefully when riding under these conditions.
Any sudden manoeuvres may lead to loss of control.
When tackling long, high-gradient downhill road tracts,
shift down gears to use engine braking. Apply one brake
at a time and use brakes sparingly. Keeping the brakes
applied all the time would cause the friction material to
overheat and reduce braking power dangerously.
Underinflated tyres reduce braking efficiency, handling
accuracy and stability in a bend.

Stopping the motorcycle

If you let go of the throttle twistgrip, the motorcycle will
slow down gradually and smoothly. Then, shift down
releasing the clutch, and finally change from first to
neutral. Apply brakes and you will bring the motorcycle
to a complete stop.
To switch the engine off, simply turn the key to OFF
(page 12).
Important
Never leave the key in the ON position when
engine is stopped, or this will damage the electric
components.
Warning
Using padlocks or other locks designed to prevent
motorcycle motion, such as brake disc locks, rear
sprocket locks, and so on is dangerous and may impair
motorcycle operation and affect the safety of rider and
passenger.

Parking
Stop and park the motorcycle on the side stand (see
page 22).
Turn the handlebar fully left and block it by pushing in the
ignition key and turning it to the LOCK position.
If you park in a garage or other facilities, make sure that
there is proper ventilation and that the motorcycle is not
near a source of heat or sparks. You may leave the
parking lights on by turning the key to position P.
Important
Do not leave the key turned to P for long periods or
the battery will run down.
Never leave the ignition key in the switch when you are
leaving your bike unattended.

31

Refueling
Never overfill the tank when refueling. Fuel should never
be touching the rim of filler recess (fig. 20).
Warning
Be sure there is no fuel trapped in the filler recess.

Max level

;;;;
fig. 20

32

MAINTENANCE
1

Tool kit and accessories (fig. 21)

Stored in the compartment under the seat is a bag (1)
that holds:
an Owners manual;
a helmet fastening cable;
a tool kit for normal maintenance and checks to be
performed by the user (placed in bag pocket).

fig. 21

To reach this compartment, the seat must be removed by

opening the catch (page 21).
The tool bag holds (fig. 22):
Box wrench for spark plugs (2).
Tommy bar (3).
Double-bit screwdriver (4).
Helmet fastening cable (5).

fig. 22
33

Routine maintenance
The maintenance schedule below specifies maintenance
operations to be carried out at regular intervals according
to time (months) or distance covered (km or miles). It
also shows the motorcycle parts requiring special care.
Proper maintenance, as specified in the maintenance
schedule, ensures long life to your motorcycle, top
performance, good reliability and safe riding. The
maintenance intervals indicated here are for motorcycles
that are not used in demanding conditions, such as riding
in town traffic, on dusty ground, long trips on mountain
roads, long trips on motorways at high speed, riding in
bad weather, and so on. In these cases, maintenance
work should be carried out more frequently. Call your
local Ducati Dealer or an authorized workshop to obtain
more information on your special needs.

34

Operation identification symbols:

) This symbol indicates that the job in question should
be entrusted to a Ducati Dealer or authorized workshop
where highly trained personnel and special equipment
are available.
C) Check and adjust
L) Lubricate and/or grease
P) Clean
S) Replace
V) Check with engine running

Operations

Predelivery

Spark plugs
Chain: tensioning and lubrication ( )

After 1000 km/

620 miles
or 6 months

Every
1000 km/
620 miles

C
C/ L

Timing belts ( )

C/ L

C/ L

C
C

Bowden cables

Clutch and brake hydraulic controls ( )

Cylinder compression ( )

Every
20000km/
12400 miles

General testing

Throttle body: synchronization and idling

adjustment

Wheel hub bearings ( )

Steering head bearing clearance ( )

Every
10000 km/
6200 miles

C
C

Air filter

Engine oil intake filter ( )

Fuel filter ( )

Engine oil filter ( )

35

Operations

After 1000 km/

620 miles
or 6 months

Every
1000 km/
620 miles

Every
10000 km/
6200 miles

Valve clearance ( )

Rear wheel rubber cush drive damper ( )

Light system and indicators

Predelivery

Battery fluid level

General lubrication ( )

Clutch and brake fluid ( )

C
L
C

Front fork oil ( )

Engine oil ( )

S
C

Wear on brake pads ( )

Front sprocket stop plate ( )

C

General cleaning

Fuel tank ( )

36

Tyres: wear and pressure

Torque of nuts and bolts ( )

Every
20000km/
12400 miles

P
C

MAIN MAINTENANCE OPERATIONS

1

Removing the fairing

Some servicing operations need the motorcycle fairing to
be removed.
Warning
Firmly secure all removed parts when refitting
them, otherwise some of them might suddenly come off
when riding and you may lose control of your motorcycle.
Important
At reassembly always use nylon washers when
tightening fastening screws, not to damage painted parts
and Plexiglas windproof cover. Some fastening screws
are of the self-tapping type; do not overtighten,
otherwise threading might damage thus avoiding further
use.
Side body panels
Unscrew the three screws (1, fig. 23.1) that hold each
body panel to the headlamp fairing.
Unscrew the screw (2) that holds each body panel to the
frame.

fig. 23.1

fig. 23.1
37

Half-faired version (fig. 23.2)

Unscrew the screw (3) that holds each body panel to the
lower support bracket.
Disconnect the indicator connectors and remove the
body panels.

Fully-faired version (fig. 23.3)

Unscrew the screw (4) that holds the left body panel to
the side stand fixing plate. Unscrew the screw (5) that
holds the right body panel to the rear brake pedal shaft.
Disconnect the indicator connectors.
Unscrew the four screws (6) that join the body panels
together at the bottom end and remove the body panels.
Omit this latter step if you wish to remove both body
panels together. Simply slide them off from under the
motorcycle. Be sure not to force them apart to avoid
damage.

3
fig. 23.2
38

fig. 23.3

Headlamp fairing
Unscrew the two nuts (1, fig. 24.1) that hold the rear
view mirrors to the headlamp fairing and remove the rear
view mirrors.
Unscrew the three screws (2, fig. 24.2) that hold each
body panel to the headlamp fairing. Move the body
panels slightly apart and unscrew the four screws (3, fig.
24.3) that fix the headlamp fairing to headlamp subframe
on both sides.
Lift the headlamp off its front fastening pin (4, fig. 24.2)
and over the headlamp.

E
2

fig. 24.2

fig. 24.1

fig. 24.3
39

Lifting the fuel tank (fig. 25.2)

Remove the seat (see page 21).
Pull the clip (1, fig. 25.1) upwards to disengage it from
the tank catch.
Lift the tank and unhook the service rod (2) from its
retainer (3).
Place the tank onto the rod (2) fitting rod end into the
hole in frame cross-member.

When finished, reverse the above procedure to refit all

the parts you have removed.

Warning
Make sure the fuel in the tank is less than 5
litres/1.32 US Gall. (the reserve light on the instrument
panel should be on) or fuel may leak out through the filler
plug breather.
Lift tank just enough to pull out service rod. Do not lift
tank exceedingly or you may damage the fuel sensor
wire and the fuel lines.
When lowering the tank, be sure the fuel lines are not
squeezed and the fuel sensor wire is not pushed too
close to vertical cylinder head.

fig. 25.1

fig. 25.2
40

Changing the air filter (fig. 26.1)

Replace air filter at the required intervals shown in the
routine maintenance chart (see page 35). The air box is
accessible after lifting the fuel tank.
Undo the clips (1) of the cover on both sides of the air
box, then remove cover (2).
Remove the filter (3, fig. 26.2) and fit a new one.
Important
A clogged filter will reduce air intake, increase fuel
consumption, reduce engine power, and foul the spark
plugs. Do not use the motorcycle without filter or
suspended matters could get into the engine and cause
damage.
Install the filter properly into its seat in the air box as
shown in figure 26.2 and refit all the parts you have
removed.

fig. 26.1

Important
If you are using the motorcycle on dusty or very
wet roads, replace filter more frequently than
recommended intervals.

fig. 26.2
41

Checking brake and clutch fluid level

Fluid level should never fall below the MIN mark on
each reservoir (fig. 27.1, 27.2 and 27.3). If level drops
below the limit, air might get into the circuit and affect
the operation of the system involved.
Brake and clutch fluid must be topped up and changed at
the intervals specified in the routine maintenance chart
by a Ducati Dealer or authorized workshop.

Important
It is recommended all brake and clutch lines be
changed every four years.
Brake system
If you find exceeding play on brake lever or pedal and
brake pads are still in good condition, contact your Ducati
Dealer or an authorized workshop to have the system
inspected and any air drained out of the circuit.

fig. 27.1

Warning
Brake and clutch fluid and will damage paintwork
and plastic parts if accidentally spilled.
Hydraulic oil is corrosive; it may cause damages and lead
to severe injuries.
Never mix different quality oils.
Check seals for proper sealing.

fig. 27.2
42

Clutch system
If the control lever has exceeding play and the
transmission snatches or jams as you try to engage a
gear, it means that there is air in the circuit. Contact your
Ducati Dealer or an authorized workshop to have the
system inspected and air drained out.
Warning
Brake fluid level will increase as clutch plate friction
material wears down. Do not exceed specified level
(3 mm/0.12 in. above minimum level).

Checking brake pads for wear (fig. 28)

Front brake
To facilitate inspection without removing the pads from
the calipers, brake pads have a wear mark. If the grooves
in the friction material are still visible, the pad is still in
good condition.
Rear brake
The friction material on each pad should be at least 1
mm/0.039 in. thick.

Important
Have the brake pads replaced at a Ducati Dealer or
authorized workshop.

MAX
MIN

fig. 27.3

fig. 28
43

Lubricating cables and joints

The condition of the outer sheaths of the throttle and
cold start cables should be checked at regular intervals.
The sheaths should show no signs of squeezing or
cracking. Work the controls to make sure the cable slides
smoothly inside the sheath: if you feel any friction or hard
spots, have the cable replaced by your Ducati Dealer or
authorized workshop. To prevent these failures, smear
the ends of the Bowden cables with SHELL Advance
Grease or Retinax LX2 at regular intervals.
For the throttle cable, it is best to remove the cover (1,
fig. 29.1) by unscrewing the two fastening screws (2) and
then grease the cable end and the pulley.
fig. 29.1
Warning
When refitting the cover, be sure to slide the cable
properly onto the suitable pulley and inside the guide in
the cover (3, fig. 29.2).

Refit the cover and tighten the screws (2).

To ensure smooth operation of side stand joint, clean off
any dirt and apply SHELL Alvania R3 at all points exposed
to friction.

fig. 29.2
44

Throttle cable adjustment

The throttle twistgrip must have a free play of 1.5 - 2
mm/0.059-0.078 in. measured at the edge of the
twistgrip, at all positions of the handlebars. If it needs
adjusting, use the suitable adjuster (1, fig. 30) provided
on the throttle control.

fig. 30
45

Checking battery electrolyte level (fig. 31)

You will need to lift the tank (page 40) before you can
check battery liquid level.
Battery liquid level must be maintained between the
maximum UPPER LEVEL and minimum LOWER
LEVEL marks on battery front.
If battery liquid level is too low, remove the caps (1) and
top up carefully with distilled water up to the upper level
line, using a small syringe or a plastic funnel.
When adding distilled water, make sure the breather tube
(2) is connected to battery breather outlet.
The breather tube must be so placed that it does not kink
or twist.
Important
Add only distilled water to the battery.
Tap water may shorten battery life.
A kinked or twisted breather tube may lead to
overpressure and damage the battery.
Warning
The battery contains sulphuric acid (electrolyte).
Avoid contact with skin and eyes as it may cause severe
burns.
If you spill some electrolyte on your skin, wash the
affected area with abundant water and seek medical
advice.
Electrolyte is poisonous: if you swallow it accidentally,
drink abundant milk or water, eat some magnesia,
scrambled eggs or drink vegetable oil and seek medical
advice without delay.
46

Always wear adequate protective clothing and a visor

when handling the battery.
Never switch on a lighter or light a match and so on to
check battery fluid level.
Do not reverse terminal polarity.

Charging the battery (fig. 31)

Before charging the battery, it is best to remove it from
the motorcycle.
Disconnect the breather tube (2).
Always disconnect the black negative terminal (-) first,
and then the red positive terminal (+).
Undo the straps (3) and remove the battery.
Warning
Batteries develop explosive gases: keep battery
away from heat sources and flames.
Charge the battery in a ventilated room.
Check the battery liquid level in each cell. If level is low in
any of the cells, top up. Note that level should not
exceed the maximum line (UPPER LEVEL), as it will rise
during charging.
Connect the battery charger leads to the battery
terminals (red to positive terminal +, black to negative
terminal -).
Important
Make sure the charger is off when you connect the
battery to it, or you might get sparks at the battery
terminals that could ignite the gases inside the cells.
Always connect the red positive terminal first.

Charge the battery at 1.5 A.

When battery is charged, check electrolyte level in each
cell. If it has dropped, top up with distilled water until
reaching the upper level.
Refit the caps (1) on the cells, reinstall the battery on its
mount and secure it with its straps (3).
Reconnect the breather tube (2).
Connect the terminals. Use some grease on the
fastening screws to improve conductive capacity.
Warning
Keep the battery out of the reach of children.
A low battery will degrade soon if not charged promptly.

UP
PE
RL
EV
EL
LO
WE
RL
EV
EL

fig. 31
47

Grease the threads of adjusting screws (3) with SHELL

Alvania R3 grease and torque check nuts (2) to 8 Nm.

Important
Improper chain tension will lead to early wear of
transmission parts.
Make sure you have adjusted to the same setting marks
on both sides of the swingarm. Refer to pointer on slider
(4, fig. 32.2, 32.3). This will ensure perfect wheel
alignment.
Grease the thread of the wheel spindle nut (1) with
SHELL Retinax HDX2 grease and torque nut to 63 Nm.
48

Chain adjustment
Turn the rear wheel slowly until you find the position
where chain tension is tightest.
Put motorcycle on the side stand and push the chain up
pressing with a finger at mid-length of swingarm. The
lower stretch of chain must have a slack of 25 mm/0.98
in. (fig. 32.1).
On 750 models, chain tension is adjusted as follows:
Slacken the nut (1, fig. 32.2) of the wheel spindle,
tighten (turn clockwise) or slacken the screw (2) on either
side of the swingarm equally to increase or reduce chain
tension. If you are slackening the chain, you will have to
push the wheel forward.
To adjust chain tension on 900 models, slacken the nuts
(1, fig. 32.3) on both sides of wheel spindle.
Slacken the check nut (2) and slacken (turn clockwise) or
tighten the screw (3) on either side of the swingarm
equally to increase or reduce chain tension. If you are
slackening the chain, you will have to push the wheel
forward.

25 mm

fig. 32.1

750

Chain lubrication
The chain fitted on your motorcycle has OR seals that
keep dirt out of and lubricant inside the sliding parts. The
seals might be irreparably damaged if the chain is
cleaned using any solvent other than those specific for
OR chains or washed using steam or water jets. After
cleaning, blow the chain dry or dry it using absorbent
material and apply SHELL Advance Chain or Advance
Teflon Chain on each link.

Important
Using non-specific lubricants may lead to severe
damage to chain, front and rear sprocket.
fig. 32.2
900

2
3
1

fig. 32.3
49

Replacing bulbs
Before replacing a burnt-out bulb, make sure that the
new one complies with voltage and wattage as specified
on page 68, Electric System, for that lighting device.
Always test new lamp before refitting the parts you have
removed.

The parking light bulb is fitted on the top section of the

headlamp body. To change it, pull out the bulb holder (3,
fig. 33.3) from headlamp body.
Remove the bulb and fit a new one.

Headlamp
To gain access to headlamp bulbs you will need to work
behind the headlamp fairing.
Remove connector (1, fig. 33.1) from the bulb.
Pull the tab (A) to remove the protective cap.
Release the clip (2, fig. 33.2) that holds the bulb in place
and take the bulb out of its socket. Fit a new bulb.
Note
Be careful to hold the new bulb at the base only.
Never touch the transparent body with your fingers or it
will blacken resulting in reduced bulb brilliancy.

Reassembly
Insert the locating pegs of the bulb base into their seats
to obtain correct alignment.
Hook the clip (2) to the headlamp holders; reconnect the
connector (1) you have detached previously and refit the
rubber cover.
1

fig. 33.1
50

Instrument panel (fig. 34)

Remove the headlamp fairing to reach the instrument
panel bulbs (see page 39). Extract the lamp holder from
behind the instrument and pull out the bulb from its
holder to replace it. The bulb holder cables are numbered
to avoid confusion in the event more bulbs need
replacing at the same time. Be sure to match the
numbers marked on the connectors in the instrument
panel.

Note
The bulb holders of the instrument panel lights have
a tang (A) to aid removal without risking to tear the
cables.
fig. 33.2

5
3
A
fig. 33.3

fig. 34
51

Turn indicators (fig. 35)

Remove the screw (1) and detach the glass (2) from the
indicator body holder.
The bulb is of the banjo-type: press and rotate anticlockwise to remove; fit the spare bulb by pressing and
turning clockwise until it clicks.
Refit the glass sliding the small tab (A) into the suitable
slot in the indicator body and tighten the screw (1).

Number plate light (fig. 36)

To expose the number plate light bulb, withdraw the
lamp holder from the number plate holder, then extract
the bulb and replace it.
Note
The bulb holder has a tang (A) to aid removal from
number plate holder without risking to tear the cables.

A
1

fig. 35
52

fig. 36

Stop light
To replace the stop and parking light bulb, unscrew the
two screws (1, fig. 37.1) that secure the glass and
remove glass. The bulb is of the banjo-type: press and
rotate anti-clockwise to remove; fit the spare bulb by
pressing and turning clockwise until it clicks (fig. 37.2).
Refit the glass and tighten the screws (1).

fig. 37.1

fig. 37.2
53

Beam setting (fig. 38.1)

When checking beam setting, put the motorcycle
upright. Tyres should be inflated at the correct pressure
and one person should be sitting astride the motorcycle,
keeping it at right angles to its longitudinal axis. Place the
motorcycle opposite a wall or a screen, 10 meters/33
feet apart from it, then draw a horizontal line dictated by
headlamp center and a vertical one in line with the
longitudinal axis of motorcycle.
If possible, perform this check in dim light.
Switch on the low beam. The height of the light spot
(measured at the upper limit between dark and lighted-up
area) should not exceed 9/10th of the height from ground
of headlamp center.
Note
The procedure described here is in compliance with
the Italian Standard establishing the maximum height
of the light beam. Owners in other countries will adapt
said procedure to the provisions in force in their
countries.

54

fig. 38.1

The height of the light beam can be corrected using

the screw (1, fig. 38.2) on the left side of the headlamp.
Turn the screw clockwise to lower the beam,
anticlockwise to raise it.
The side position of the headlamp is adjusted using
the adjusting screw (2, fig. 38.2) on the right side of
headlamp. Turn the screw clockwise to move the beam
to the right, anticlockwise to move it to the left.

Tyre pressures
Front tyre:
2.1-2.2 bar
Rear tyre:
2.1-2.3 bar
As tyre pressure is affected by temperature and altitude
variations, you are advised to check and adjust it
whenever you are riding in areas where ample variations
in temperature or altitude occur.
Important
Check and set tyre pressure when tyres are cold.
To avoid front wheel rim distortion, when riding on
bumpy roads, increase front tyre pressure by 0.2 - 0.3
bar.

UPPER

LOWER

LEFT

RIGHT

1
fig. 38.2
55

Tyre repair or replacement

In the event of a tiny puncture, tubeless tyres will take a
long time to deflate, as they tend to keep air inside. If
you find low pressure on one tyre, check the tyre for
punctures.

Warning
A tyre must be replaced when punctured. Replace
tyres with recommended standard tyres only.
Be sure to tighten the valve caps securely to avoid leaks
when riding. Never use tube type tyres. Failure to heed
this warning may lead to sudden tyre bursting and to
serious danger to rider and passenger.
After replacing a tyre, the wheel must be balanced.

Minimum tread depth

Measure tread depth (S, fig. 39) at the point where tread
is most worn down. It should not be less than 2 mm/0.08
in. and anyway not below the legal limit.
Important
Visually inspect the tyres at regular intervals for
cracks and cuts, especially on the side walls, bulges or
large spots that are indicative of internal damage.
Replace them if badly damaged.
Remove any stones or other foreign bodies caught in the
tread.

Important
Do not remove or shift the wheel balancing
weights.
Note
If tyres need replacing, contact a Ducati Dealer or
authorized workshop to make sure wheels are removed
and refitted correctly.

fig. 39
56

Checking engine oil level (fig. 40)

Engine oil level can be checked through the sight glass
(1) provided on the clutch cover.
When checking oil level, the motorcycle should be
upright and the engine warm.
Allow a few minutes for oil to settle to a steady level
after stopping the engine.
Oil level should be between the marks near the sight
glass.
Top up oil level with SHELL Advance Ultra 4, if low.
Undo the filler plug (2) and top up to correct level.
Refit the plug.

750

Have engine oil and oil filters changed by your Ducati

Dealer or at an authorized workshop at regular intervals,
as specified in the maintenance schedule.

fig. 40

10W
Multigrade Unigrade

Viscosity
SAE 20W-50
The other viscosity degrees indicated in the table can be
used if the local average temperature is within the limits
specified for that oil viscosity.

900

20W
20
30
40
20W40
15W40

20W50

15W50

10W40
10W30
10

10

20

30

40C

57

Cleaning and replacing the spark plugs (fig. 41)

Spark plugs are essential to smooth engine running and
should be checked at regular intervals. This is done quite
easily and quickly and provides a good measure of engine
condition.
Remove the l.h. fairing, remove the spark plug caps from
the cylinder head using the wrench supplied with the
bike.

If you do not have a torque wrench, you can use the

wrench supplied with the tool kit to tighten the spark
plug an additional 1/2 turn.
Important
Never use spark plugs with a heat rating other than
recommended or a thread length other than standard.
Spark plugs should be tightened properly.

Check the color of the insulating ceramic material of the

central electrode: a light brown, even color is a sign of
good engine condition. If color has altered or you find any
dark deposits, change the spark plug and report this to
your Dealer or authorized workshop.
Check wear on the central electrode. If it looks worn out
or has a vitreous appearance, change the spark plug.
Check electrode gap: it should be 0.6-0.7 mm/0.0230.027 in.
Important
If the gap needs adjusting, be very careful when
bending the side electrode. If gap is too wide or too
close, engine performance will be affected. This could
also cause difficult starting or irregular idling.
Clean the electrode and the insulating material accurately
using a small metal brush and check seal condition.
Clean the seat in the cylinder head. Be careful not to let
any foreign matters fall into the combustion chamber.
Refit spark plug into cylinder head. Tighten until thread is
fully into the head. Tighten the spark plug to 20 Nm.
58

fig. 41

Cleaning the motorcycle

To preserve the finish of metal parts and paintwork, wash
and clean your motorcycle at regular intervals, anyway
according to the road conditions you ride in.
Use specific products only. Prefer biodegradable
products. Avoid aggressive detergents or solvents.
Important
Do not wash your motorcycle right after use. When
the motorcycle is still hot, water drops will evaporate
faster and spot hot surfaces.
Do not use high pressure water jets.
Never aim the nozzle direct at wheel bearings, front fork
seals, electric items, air inlets or exhaust pipe ends.
If needed, clean off stubborn dirt or exceeding grease
from engine parts using a degreasing agent. Be sure to
avoid contact with drive parts (chain, sprockets, etc.).
Rinse with warm water and dry all surfaces with chamois
leather.
Warning
Braking performance may be impaired immediately
after washing the motorcycle.
Never grease or lubricate the brake discs. Loss of braking
and further accidents may occur. Clean the discs with an
oil-free solvent.

Storing the bike away

If the motorcycle is to be left unridden over long periods,
it is advisable to carry out the following operations before
storing it away:
clean the motorcycle;
remove tank drain plug and seal and drain all fuel from
tank;
pour a few drops of engine oil into the cylinders through
the spark plug seats, then crank the engine by hand a
few times so a protective film of oil will spread on
cylinder inner walls;
place motorcycle on the supplied paddock stand;
remove the battery and keep it well charged and
efficient. Battery should be checked and charged
whenever the motorcycle has been left unridden for over
a month;
protect the motorcycle with a suitable canvas that will
protect paintwork and let condensate breathe out. A
special canvas cover is available from Ducati Spare Parts
Department.

Important notes
Some countries, such as France, Germany, Great Britain,
Switzerland, etc. have compulsory emission and noise
standards that include mandatory inspections at regular
intervals.
It is the Owners responsibility to have any parts not in
compliance with the standards in force in his/her country
replaced with spare parts complying with local law.
59

TECHNICAL DATA

Overall dimensions (mm) (fig. 42)

Weights
Dry weight:
183 Kg/403.4 lb. (750); 188 Kg/414 lb. (900).
Carrying full load:
385 Kg/848.7 lb.
Warning
Failure to observe weight limits could result in poor
handling and impair the performance of your motorcycle,
and you may lose control of the motorcycle.

fig. 42
60

Top-ups

Type of fluid

cu dm (liters)/US Gall.

Fuel tank, including a reserve

of 4 cu dm (liters)/1.05 US Gall.

Gasoline 95-98 RON

16/4.22

Oil sump and oil filter

SHELL-Advance Ultra 4

3.3/0.87 (750)
3.9/1.03 (900)

Front/Rear brake and clutch circuits

Special fluid for hydraulic systems

SHELL-Advance Brake DOT 4

Protectant for electric contacts

Spray for electric systems

SHELL-Advance Contact Cleaner

Front fork

SHELL-Advance Fork 7.5 or Donax TA

0.531/0.14 (each leg)

Important
Additives to fuel or lubricants are not allowed.

61

Engine
Twin cylinder, four-stroke, 90 L type, longitudinal.
Bore:
88 mm/3.46 in. (750); 92 mm/3.62 in. (900).
Stroke:
61.5 mm/2.42 in. (750); 68 mm/2.67 in. (900).
Total displacement:
748 c.c./45.62 cu. in. (750); 904 c.c./57.58 cu. in. (900).
Compression ratio:
9.00.5:1 (750); 9.20.5:1 (900).
Max. power at crankshaft (95/1/CE):
45 kW - 61 HP at 8250 rpm (750);
58 kW - 79 HP at 7500 rpm (900).
Max torque at crankshaft (95/1/CE):
60 Nm at 6000 rpm (750);
75.5 Nm at 6500 rpm (900).
Max. rotation speed
9000 rpm
Important
Do not exceed specified rotation speed limits under
any running condition.

62

Timing system
Desmodromic (type) with two valves per cylinder,
operated by four rockers (2 opening rockers and 2 closing
rockers) and an overhead camshaft. It is operated by the
crankshaft through spur gears, belt rollers and toothed
belts.

Desmodromic timing system (fig. 43)

1) Opening (or upper) rocker.
2) Opening rocker shim.
3) Split rings.
4) Closing (or lower) rocker shim.
5) Return spring for lower rocker.
6) Closing (or lower) rocker.
7) Camshaft.
8) Valve.

Performance data
Maximum speed in any gear should be reached only after
a correct running-in period with the motorcycle properly
serviced at the recommended intervals.
Max. speed (rider alone):
205 Km/h - 127.4 mph (750);
225 Km/h - 140 mph (900).

Spark plugs
Make:
CHAMPION
Type:
RA 6 HC

5
2

3
4
6

fig. 43
63

Brakes

Front brake
With double drilled disc.
Material:
steel.
Disc diameter:
320 mm/12.59 in.
Hydraulically operated by a control lever on right
handlebar.
Braking surface:
88 sq cm/13.64 in.
Brake calipers with separate pistons.
Make:
BREMBO
Type:
30/34-4 pistons
Friction material:
FERIT I/D 450 FF.
Master cylinder type:
PSC 16.
Rear brake
With fixed drilled disc.
Material:
steel.
Disc diameter:
245 mm/9.64 in.
Hydraulically operated by a pedal on RH side.
Braking surface:
25 sq cm/3.87 sq. in.
64

Make:
BREMBO
Type:
P 32 G.
Friction material:
FERIT I/D 450 FF
Master cylinder type:
PS 11.
Warning
Brake fluid can dissolve paintwork and cause
severe eye and skin injuries in the event of accidental
spilling. Wash the affected area with abundant running
water.

Transmission
Clutch:
wet multi-plate clutch (750);
dry multi-plate clutch (900).
Clutch is operated by a control lever on left handlebar.
Drive is transmitted from engine to gearbox main shaft
via spur gears.
Gear ratio:
33/61 (750);
32/59 (900).
Gearbox:
5-speed (750);
6-speed (900).
Gearbox with constant mesh gears, gear change pedal
on left side of motorcycle.
Front/rear sprocket ratio: 15/40.
Total gear ratios:
1st gear 16/40 (750); 15/37 (900).
2nd gear 21/36 (750); 17/30 (900).
3rd gear 24/32 (750); 20/27 (900).
4th gear 27/29 (750); 22/24 (900).
5th gear 29/28 (750); 24/23 (900).
6th gear
28/24 (900).

Links:
98 (750); 102 (900).
Important
The above gear ratios are the homologated ones
and under no circumstances must they be modified.
If you wish to tune up your motorcycle for competitive
trials, you may refer to Ducati Motor S.p.A. who will be
glad to provide information about the special ratios
available. Relevant instructions and original spare parts
are available from your local Dealer or authorized
workshop.

Warning
If the rear sprocket needs replacing, contact a
Ducati Dealer or an authorized workshop. If improperly
replaced, this component could seriously endanger your
safety and that or your passenger, and cause irreparable
damage to your motorcycle.

Drive chain from gearbox to rear wheel:

Make:
DID
Type:
520 VL4.
Size:
5/8"x1/4"
65

Frame
Tubular trestle frame with upper section made of highstrength steel.
Steering angle (on each side):
28
Headstock angle:
24
Trail:
96 mm/3.78 in. (750); 100 mm/3.93 in. (900).

Wheels
Three-spoke, light-alloy rims.
Front wheel
Make:
BREMBO
Dimensions:
3.50x17"
Rear wheel
Make:
BREMBO
Dimensions:
4.50x17" (750); 5.50x17" (900).
Front wheel spindle can be removed.
66

Tyres
Front tyre
Tubeless, radial tyre.
Size:
120/70-ZR17.
Rear tyre
Tubeless, radial tyre.
Size:
160/60-ZR17 (750); 170/60-ZR17 (900).

Suspensions
Front
Hydraulic upside-down fork.
The front fork used on the 900 models features outer
adjusters for rebound, compression, and preload (for
inner springs of fork legs).
Stanchion diameter mm:
43 mm/1.69 in.
Travel along leg axis:
120 mm/5.12 in.

Rear
The rear shock absorber enables the adjustment of
rebound and compression damping and spring preload.
At the bottom pivot point it is connected to the
swingarm. Swingarm is made from steel (750) or light
alloy (900) and hinges on a pivot pin passing through the
engine. The whole system gives the bike excellent
stability.
Travel:
71 mm/2.79 in.
Rear wheel travel:
135 mm/5.31 in.

67

Electric system
Basic electric items are:
Headlamp with double filament 12V-55/60 W iodine
bulb.
12V-5W parking light.
Instrument panel, 12V-3W warning lights; 12V-2W and
3W instrument lights.
Electrical controls on handlebar.
Turn indicators, 12V-10W bulbs.
Horn.
Stop light switches.
Battery 12V-16 Ah.
Generator 12V-520W.
Electronic voltage regulator (rectifier), protected by a
40A fuse located on the side of the battery.
Starter motor, 12V-0.7 kW.
Tail light, 12V-5/21W double-filament bulb for stop light
and parking light; 12V-5W bulb for number plate light.
Note
See Replacing bulbs on page 50 for relevant
instructions.

68

Fuses
The main fuse box is located on the left side of headlamp
subframe (fig. 44.1).
To expose the fuses, take off the box protective cover
(1). Mounting position and ampere capacity are marked
on box cover.
Only 6 fuses are connected. There are two spare fuses.
The fuses placed before the battery (fig. 44.2) protect the
electronic regulator (2) (40A) and the injection relays. The
latter fuses (3) are rated 20A and 3A respectively.
Remove the fuse cap (4) to expose it.
A blown fuse is identified by the interrupted inner
filament (5, fig. 44.3).
Important
Switch the ignition key to OFF before replacing a
fuse to avoid possible short circuits.
Warning
Never use a fuse with a rating other than specified.
Failure to observe this rule may damage the electric
system or even lead to fire.

1
5

E
IN GOOD CONDITION

fig. 44.1
4

BLOWN

fig. 44.3

fig. 44.2
69

Legend of the wiring diagram of electric

system/ignition
1) Right switch
2) Key-operated switch
3) Ignition relay
4) Fuse box
5) Turn indicator flasher
6) Starter motor
7) Starter contactor
8) Battery
9) Oil temperature sensor (instrument)
10) Rear right-turn indicator
11) Tail light
12) Number plate light
13) Rear left-turn indicator
14) Fuel tank
15) Diagnosis connector
16) Horizontal cylinder coil
17) Vertical cylinder coil
18) Horizontal cylinder spark plug
19) Vertical cylinder spark plug
20) Horizontal cylinder injector
21) Vertical cylinder injector
22) Throttle position sensor
23) Engine rpm/timing sensor
24) Oil temperature sensor
25) Stand light switch
26) Injection/ignition unit
27) Injection relay
28) Injection relay fuses
29) Horn
70

30) Regulator fuse (40A)

31) Regulator
32) Generator
33) Neutral light switch
34) Oil pressure switch
35) Rear STOP light switch
36) Front STOP light switch
37) Left switch
38) Air temperature sensor
39) Instrument panel
40) Front left-turn indicator
41) Headlamp
42) Front right-turn indicator

Wire color coding

P Pink
GR-Bk Grey-Black
Y-G Yellow-Green
G Green
R-G Red-Green
W-R White-Red
O-Bk Orange-Black
V-Bk Violet-Black
Y Yellow
W-B White-Blue
BN Brown
G-W Green-White
O-W Orange-White
R-Bk Red-Black
R-B Red-Blue
GR-R Grey-Red
R Red
G-Bk Green-Black
V Violet
Y-Bk Yellow-Black
GR Grey
G-B Green-Blue
Lb Light blue
Bk Black

Legend of fuse box (4)

Pos.

Description

Rat.

1-9

Main switch

30 A

2-10

High and low beams

15 A

3-11

Turn indicators, warning lights,

7.5 A
tail lights and instrument panel lights

4-12

Stop, warning horn

7.5 A

5-13

Injection

7.5 A

6-14

Diagnostics

3A

7-15

Spare

30 A

8-16

Spare

15 A

Note
The system wiring diagram is at the end of this
manual.

71

FOR UNITED STATES OF AMERICA VERSION

ONLY

USA

Reporting of safety defects

If you believe that your vehicle has a defect which could
cause a crash or could cause injury or death, you should
immediately inform the National Highway Traffic Safety
Administration (NHTSA) in addition to notifying Ducati
North America. If NHTSA receives similar complaints, it
may open an investigation, and if it finds that a safety
defect exists in a group of vehicles, it may order a recall
and remedy campaign. However, NHTSA cannot become
involved in individual problems between you, your dealer,
or Ducati North America. To contact NHTSA, you may
either call the Auto Safety Hotline toll-free at 1-800-4249393 (or 366-0123 in Washington, D.C. area) or write to:
NHTSA, U.S. Department of Transportation, Washington,
D.C. 20590. You can also obtain other information about
motor vehicle safety from the Hotline.
Safety warnings
Traffic Rules vary from jurisdiction to jurisdiction. Know
the regulations in your jurisdiction before riding this
motorcycle.

72

Warning
This motorcycle is designed and intended for use
on streets and other smooth, paved areas only. Do not
use this motorcycle on unpaved surfaces. Such use could
lead to upset or other accident.
Noise emission warranty
Ducati Motor S.p.A. warrants that this exhaust system, at
the time of sale, meets all applicable U.S. EPA Federal
noise standards. This warranty extends to the first
person who buys this exhaust system for purposes other
than resale, and to all subsequent buyers. Warranty
claims should be directed to: Ducati North America, Inc.,
237 West Parkway, Pompton Plains, New Jersey, 074441028 Tel: 001.973.839-2600 Fax: 001.973.839-2331.
Noise and exhaust emission control system
information
Source of Emissions
The combustion process produces carbon monoxide and
hydrocarbons. Control of hydrocarbons is very important
because under certain conditions, they react to form
photochemical smog when subjected to sunlight. Carbon
monoxide does not react in the same way, but is toxic.
Ducati utilizes lean carburetor settings and other systems
to reduce carbon monoxide and hydrocarbons.
Exhaust Emission Control System
The Exhaust Emission Control System is composed of
lean carburetor settings, and no adjustments should be

Crankcase Emission Control System

The engine is equipped with a closed crankcase system
to prevent discharging crankcase emissions into the
atmosphere. Blow-by gas is returned to the combustion
chamber through the air cleaner and the throttle body.
Evaporative Emission Control System
California motorcycles are equipped with an evaporative
emission control system which consists of a charcoal
canister and associated piping. This system prevents the
escape of fuel vapors from the throttle body and fuel
tank.
Tampering warning
Tampering with Noise Control System Prohibited. Federal
Law prohibits the following acts or causing thereof:
(1) the removal or rendering inoperative by any person,
other than for purposes of maintenance, repair, or
replacement, of any device or element of design
incorporated into any new vehicle for the purpose of
noise control prior to its sale or delivery to the ultimate
purchaser or while it is in use; or
(2) the use of the vehicle after such device or element of
design has been removed or rendered inoperative by any
person.

Among those acts presumed to constitute tampering

are the acts listed below:
(1) Removal of, or puncturing the muffler, baffles, header
pipes or any other component which conducts exhaust
gases.
(2) Removal or puncturing of any part of the intake
system.
(3) Lack of proper maintenance.
(4) Replacing any moving part of the vehicle, or parts of
the exhaust or intake system, with parts other than those
specified by the manufacturer.
This product should be checked for repair or replacement
if the motorcycle noise has increased significantly
through use. Otherwise, the owner may become subject
to penalties under state and local ordinances.
Problems that may affect motorcycle emissions
If you are aware of any of the following symptoms, have
the vehicle inspected and repaired by your local Ducati
dealer.
Symptoms:
Hard starting or stalling after starting.
Rough idle.
Misfiring or backfiring during acceleration.
After-burning (backfiring).
Poor performance (driveability) and poor economy.

73

E
USA

made except idle speed adjustments with the throttle

stop screw. The Exhaust Emission Control System is
separate from the crankcase emission control system.

USA

Riding safety
The points given below are applicable for every day
motorcycle use and shoud be carefully observed for safe
and effective vehicle operation.
A motorcycle does not provide the impact protection of
an automobile, so defensive riding in addition to wearing
protective apparel is extremely important.
Do not let protective apparel give you a false sense of
security.
Before changing lanes, look over your shoulder to make
sure the way is clear. Do not rely solely on the rear view
mirror; you may misjudge a vehicles distance and speed,
or you may not see it at all.
When going up steep slopes, shift to a lower gear so that
there is plenty of power to spare rather than overloading
the engine.
When applying the brakes, use both the front and rear
brakes. Applying only one brake for sudden braking may
cause the motorcycle to skid and lose control.
When going down long slopes, control vehicle speed by
closing the throttle. Use the front and rear brakes for
auxiliary braking.
Riding at the proper rate of speed and avoiding
unnecessarily fast acceleration are important not only for
safety and low fuel consumption but also for long vehicle
life and quieter operation.
When riding in wet conditions or on loose roadway
surfaces, the ability to maneuver will be reduced. All of
your actions should be smooth under these conditions.
Sudden acceleration, braking or turning may cause loss
of control.
74

When the roadway is wet, rely more on the throttle to

control vehicle speed and less on the front and rear
brakes.
The throttle should also be used judiciously to avoid
skidding the rear wheel from too rapid acceleration or
deceleration.
On rough roads, exercise caution, slow down, and grip
the fuel tank with your knees for better stability.
When quick acceleration is necessary as in passing, shift
to a lower gear to obtain the necessary power.
Do not down shift at too high an r.p.m. to avoid damage
to the engine from overreving.
Avoiding unnecessary weaving is important to the safety
of both the rider and other motorists.
Do not exceed the legal speed limit or drive too fast for
existing conditions. High speed increases the influence
of any condition affecting stability and the loss of control.
Operate motorcycle only at moderate speed and out of
traffic until you have become thoroughly familiar with its
operation and handling characteristics under all
conditions. This is a very high performance motorcycle,
designed and intended for use by experienced careful
riders only!
A new motorcycle must be operated according to a
special break-in procedure (see Running in
recommendations).
Warning
Before starting engine, check for proper operation
of brake, clutch, shifter, throttle controls, correct fuel and
oil supply.

Warning
Do not ride the motorcycle with helmets attached
to the hook; the helmets could cause an accident by
distracting the operator or interfering with normal vehicle
operation.
Protective apparel
Always wear a helmet. Most motorcycle accident
fatalities are due to head injuries.
For safety eye protection, gloves, and high top, sturdy
boots should also be worn.

The exhaust system becomes very hot during operation,

never touch the exhaust system. Wear clothing that fully
covers your legs. Do not wear loose clothing which could
catch on the control levers, footrests, wheels, or chain.
Any amount of alcohol will significantly interfere with
your ability to safely operate your motorcycle. Dont drink
and ride.
Vehicle identification number (V.I.N.);
Every Ducati motorcycle is identified by two identification
numbers (see page 9). Figure A specifically shows the
identification numbers.

MODEL DESIGNATION
ENGINE TYPE
MODEL YEAR
sequential
number
ZDM 1H B 7 R
H
P B 000000
Varies-can be thru 9 or X (Check digit for factory
use)
fig. A
75

E
USA

Gasoline is extremely flammable and is explosive under

certain conditions. Refuell in a well ventilated area with
the engine stopped. Do not smoke or allow open flames
or sparks when refuelling or servicing the fuel system.
Always close the fuel petcock when the engine is not
running to prevent flooding of the throttle body. Do not
overfill fuel tank (see instructions page 32).
Motorcycle exhaust contains poisonous carbon monoxide
gas. Do not inhale exhaust gases and never run the
engine in a closed garage or confined area.
Use only Ducati approved parts and accessories.
This motorcycle was not intended to be equipped with a
sidecar or to be used to tow any trailer or other vehicle.
Ducati does not manufacture sidecars or trailers and
cannot predict the effects of such accessories on
handling or stability, but can only warn that the effects
will be adverse and any damage to motorcycle
components caused by the use of such accessories will
not be remedied under warranty.

Label location (fig. B)

3

10

USA

7 7

11

only for California

76

fig. B

OBJECT IN MIRROR ARE

CLOSER THAN THEY APPEAR

Cod. 433 1 166 1A

WARNING

DO NOT ATTEMPT TO LOOK THROUGH THIS FAIRING. THIS IS NOT

A WINDSHIELD, BUT AN AERODYNAMIC FAIRING ONLY; FAILURE
TO OBSERVE THIS WARNING COULD RESULT IN A COLLISION OR
UPSET AND CONSEQUENT SERIOUS BODILY INJURY.
Cod. 433 1 165 1A

HELMET HOLDER
UNDER THE SEAT

Tensione catena (sul cavalletto centrale)

Chain Tension Adjustment (on centre stand)
=
=

2
30 mm

4
Manufactured by

Cod. 432 1 233 1A

DATE:

07/97

GVWR: 925.9 Lbs (420 kg)

GAWR front: 319.7 Lbs (145 kg) with 120/70ZR17 tire, MT 3.50x17 RIM at 32.7 PSI cold.
GAWR rear: 606.2 Lbs (275 kg) with 170/60ZR17 tire, MT 5.50x17 RIM at 36.9 PSI cold.
This vehicle conforms to all applicable Federal Motor Vehicle Safety standards in effect on the date
of manufacture shown above.
Type classification: Motorcycle
Vehicle I.D. No.: ZDM1TB9PXWB000001

Cod. 432 1 234 1A

USA

MOTORCYCLE NOISE EMISSION CONTROL INFORMATION

THIS 1998 DUC46P0944 MOTORCYCLE, ZDM1TB9PXWB000001
MEETS EPA NOISE EMISSION REQUIREMENTS OF 80 dBA AT 4675 RPM BY
THE FEDERAL TEST PROCEDURE.
MODIFICATIONS WHICH CAUSE THIS MOTORCYCLE TO EXCEED FEDERAL
NOISE STANDARDS ARE PROHIBITED BY FEDERAL LAW.
SEE OWNER'S MANUAL.

6
VEHICLE EMISSION CONTROL INFORMATION
Engine displacement: 904 cc
Engine family: WDUCC0944ST2
Engine exhaust control system: MFI

VEHICLE EMISSION CONTROL INFORMATION

Engine displacement: 904 cc
Engine family: WDUCC0944ST2
Engine exhaust control system: MFI
Evap family:

THIS VEHICLE CONFORMS TO U.S. EPA AND

CALIFORNIA REGULATIONS APPLICABLE TO 1998
MODEL YEAR NEW MOTORCYCLES AND IS
CERTIFIED TO 1.4 HC G/KM ENGINE FAMILY
EXHAUST EMISSION STANDARD IN CALIFORNIA
ENGINE TUNE-UP SPECIFICATIONS

THIS VEHICLE CONFORMS TO U.S. EPA

REGULATIONS APPLICABLE TO 1998
MODEL YEAR NEW MOTORCYCLES

ENGINE TUNE-UP SPECIFICATIONS

ITEM
IGNITION TIMING:
IDLE SPEED (RPM):
IDLE MIXTURE:

SPECIFICATIONS
2 bTDC at idle speed
1200 0.12 mm

ITEM
IGNITION TIMING:
IDLE SPEED (RPM):
IDLE MIXTURE:

INSTRUCTIONS
No adjustment
No adjustment
No adjustment

Opening 0.05 0.12 mm

VALVE CLEARANCE (in & ex):

SPECIFICATIONS
2 bTDC at idle speed
1200 0.12 mm

INSTRUCTIONS
No adjustment
No adjustment
No adjustment

CAUTION

NEVER FILL TANK SO FUEL LEVEL RISES INTO FILLER

NECK. IF TANK IS OVERFILLED, HEAT MAY CAUSE FUEL
TO EXPAND AND FLOW INTO EVAPORATIVE EMISSION
CONTROL SYSTEM RESULTING IN HARD STARTING AND
ENGINE HESITATION.

Opening 0.05 0.12 mm

VALVE CLEARANCE (in & ex):

See Service Manual

Closing 0.03 0.12 mm

SPARK PLUG: CHAMPION RA4HC
OIL: SAE 20W50
SPARK PLUG GAP (mm): 0.5 0.6
FUEL: Unleaded gasoline

See Service Manual

Closing 0.03 0.12 mm

SPARK PLUG: CHAMPION RA4HC
OIL: SAE 20W50
SPARK PLUG GAP (mm): 0.5 0.6
FUEL: Unleaded gasoline

- BOLOGNA - ITALY

- BOLOGNA - ITALY

TO HORIZONTAL MANIFOLD
Via [Link],3
40132 BOLOGNA
ITALY
CANISTER

TO VERTICAL MANIFOLD

SFIATO
BLEED

RITORNO
BACKFLOW

WARNING
CONTAINS HIGHLY COM-PRESSED
GAS. USE ONLY PERFECTLY DRY
NITROGEN GAS. OTHER GASES
MAY CAUSE EXPLOSION. DO NOT
INCINERATE. REFER TO OWNER'S
MANUAL FOR REGULATING GAS.

DRENAGGIO
DRAINAGE

VEHICLE EMISSION CONTROL LABEL

ENGINE DISPLACEMENT : 904 cc. ENGINE FAMILY :
THIS VEHICLE CONFORMS TO U.S. EPA AND CALIFORNIA REGULATIONS
APPLICABLE TO 1998 MODEL YEAR NEW MOTORCYCLES.
EVAP FAMILY :

MANDATA
DELIVERY

11

10

WARM AIR INLET

77

California evaporation emission system

This system consists of (fig. C):
1) Warn air inlet;
2) Canister;
3) DellOrto jet;
4) Intake manifolds;
5) Breather pipe;
6) Fuel tank.

USA

Ducati limited warranty on emission control

system
Ducati North America, Inc., 237 West Parkway, Pompton
Plains, New Jersey 07444-1028 warrants that each new
1998 and later Ducati motorcycle, that includes as
standard equipment a headlight, tail-light and stoplight,
and is street legal:
A) is designed, built and equipped so as to conform at
the time of initial retail purchase with all applicable
regulations of the United States Environmental
Protection Agency, and the California Air Resources
Board; and
B) is free from defects in material and workmanship
which cause such motorcycle to fail to conform with
applicable regulations of the United States Environmental
Protection Agency or the California Air Resources Board
for a period of use, depending on the engine
displacement,of 12,000 kilometers (7,456 miles), if the
motorcycles engine displacement is less than 170 cubic
centimeters; of 18,000 kilometers (11,185 miles), if the
motorcycles engine displacement is equal to or greater
than 170 cubic centimeters but less than 280 cubic
centimeters; or of 30,000 kilometers (18,641 miles), if
the motorcycles engine displacement is 280 cubic
centimeters or greater; or 5 (five) years from the date of
initial retail delivery, whichever first occurs.

Important
In the event of fuel system malfunction, contact
Ducatis authorized Service Centres.

3
6
4

2
1
5

fig. C
78

I. Coverage
Warranty defects shall be remedied during customary
business hours at any authorized Ducati motorcycle
dealer located within the United States of America in

parts replaced and labor charges based on Ducatis

recommended time allowance for the warranty repair and
the geographically appropriate hourly labor rate. The
owner may be required to keep receipts and failed parts
in order to receive compensation.
II. Limitations
This Emission Control System Warranty shall not cover
any of the following:
A. Repair or replacement required as a result of
(1) accident,
(2) misuse,
(3) repairs improperly performed or replacements
improperly installed,
(4) use of replacement parts or accessories not
conforming to Ducati specifications which adversely
affect performance and/or
(5) use in competitive racing or related events.
B. Inspections, replacement of parts and other services
and adjustments required for routine maintenance.
C. Any motorcycle on which odometer mileage has been
changed so that actual mileage cannot be readily
determined.
III. Limited liability
A. The liability of Ducati under this Emission Control
Systems Warranty is limited solely to the remedying of
defects in material or workmanship by an authorized
Ducati motorcycle dealer at its place of business during
customary business hours. This warranty does not cover
inconvenience or loss of use of the motorcycle or
79

E
USA

compliance with the Clean Air Act and applicable

regulations of the United States Environmental
Protection Agency and the California Air Resources
Board. Any part or parts replaced under this warranty
shall become the property of Ducati.
In the state of California only, emissions related
warranted parts are specifically defined by that states
Emissions Warranty Parts List. These warranted parts
are: carburetor and internal parts; intake manifold; fuel
tank, fuel injection system; spark advance mechanism;
crankcase breather; air cutoff valves; fuel tank cap for
evaporative emission controlled vehicles; oil filler cap;
pressure control valve; fuel/vapor separator; canister;
igniters; breaker governors; ignition coils; ignition wires;
ignition points, condensers, and spark plugs if failure
occors prior to the first scheduled replacement, and
hoses, clamps, fittings and tubing used directly in these
parts. Since emission related parts may vary from model
to model, certain models may not contain all of these
parts and certain models may contain functionally
equivalent parts.
In the state of California only, Emission Control System
emergency repairs, as provided for in the California
Administrative Code, may be performed by other than an
authorized Ducati dealer. An emergency situation occurs
when an authorized Ducati dealer is not reasonably
available, a part is not available within 30 days, or a repair
is not complete within 30 days. Any replacement part can
be used in an emergency repair. Ducati will reimburse the
owner for the expenses, including diagnosis, not to
exceed Ducatis suggested retail price for all warranted

USA

transportation of the motorcycle to or from the Ducati

dealer. Ducati shall not be liable for any other expenses,
loss or damage, whether direct, incidental, consequential
or exemplary arising in connection with the sale or use of
or inability to use the Ducati motorcycle for any purpose.
Some states do not allow the exclusion or limitation of
any incidental or consequential damages, so the above
limitations may not apply to you.
B. No express emission control system warranty is given
by Ducati except as specifically set forth herein. Any
emission control system warranty implied by law,
including any warranty of merchantability or fitness for a
particular purpose, is limited to the express emission
control systems warranty terms stated in this warranty.
The foregoing statements of warranty are exclusive and
in lieu of all other remedies. Some states do not allow
limitations on how long an implied warranty lasts so the
above limitation may not apply to you.
C. No dealer is authorized to modify this Ducati Limited
Emission Control Systems Warranty.
IV. Legal rights
This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
V. This warranty is in addition to the Ducati limited
motorcycle warranty.
VI. Additional information
Any replacement part that is equivalent in performance
and durability may be used in the performance of any
80

maintenance or repairs. However, Ducati is not liable for

these parts. The owner is responsible for the
performance of all required maintenance. Such
maintenance may be performed at a service
establishment or by any individual. The warranty period
begins on the date the motorcycle is delivered to an
ultimate purchaser.
Ducati North America, Inc..
237 West Parkway
Pompton Plains, New Jersey, 07444-1028
001.973.839-2600

Routine maintenance record

km/miles

Ducati
Service Name

Mileage

Date

1,000/621
10,000/6,214

20,000/12,427
30,000/18,641
40,000/24,855
50,000/31,068

81

82

DUCATIMOTOR spa
Via Cavalieri Ducati, 3
40132 Bologna, Italy
Tel 39.051.6413111
Fax 39.051.406580
Internet: [Link]

913.7.066.1A
Stampato 07/1999

2
OFF
RUN

START

1
Lb

W/R

G/Bk G/R

1
2
3
4
5
6
7
8

LOCK
PARK
OFF
ON

86

30

87
85

4
R/B

W/R

2 5

3 6

49+

9
10
11
12
13
14
15
16

Bk

31

49a

Lb

RB

GrBk

Gr/R
Y

11

Y/G

1
B

W/G

10 W

10 W

Bn

42

WG

Bk

R/Bk
W/R

10

OBk

BN

5/21 W

W/Bk 1
W/G 2
3
4
Bk

41

12

5W

55/60 W

Y/BK

5W

Bk

WBk

13

10 W

Bn

Gr
B/W

14

27

40

W/R

W/Bk

10 W

20

G
W
R
Bk

R/B

R/Bk
4 3 1 2

W/Bn

Bk

B
Bk

Bn/W

Bk

Bk

26
OIL
12
13
C

RPM X 1000

T
A

9 10 11

Bk

40

1
5

W
W/R
B

AMP
AMP

15
16
17
18

WR
Gr

Gr/R

K B J C D A G H F E

Y/G

V/Bk
Gr/R

V/Bk

Y YY

V/O

21

G
40

20

22

23
24
25

CLAXON

Lo

11
12
13

17

Hi

POS.

35

34

33

32

31

30

29

37

22

SSS

37

K B J C D A G H F E

Lo
HORN
TURN

OIL

SC

7 12

22

1 11

MOT

POT

A BC

3 2 1

PASSING

26

Hi

U.S. - Australia Japan versions

87 13

16

87

19

18

2
1

25

+
13

36

+
6

38

26

9
10

Bn/W
OB

TURN

PASSING

Bn/W
YG

HORN

22
1
11

AIR

WR
R
Y

18

R R
Bk Bk

SC
7
12

22

V/Bk

19

4
22

14

Gr/B
WR

FUEL

K
D
B
C
A
E
F
H
J
G

AMP

AMP

GND
N.C.
16

BK

TURN

20

HI BEAM

NEUTRAL

B/BK

300

Km/h

2
3

15

80

86

30

120

85
87

24

23

22

39

P/Bk

3 2 1

OIL

1
4
3
2
5
6

21 20

C
TUTTI I CONNETTORI SONO VISTI DA C
ALL CONNECTORS ARE VIEWED FROM 'C'