En Electrical information B252 seriesWARNING READ THIS OPERATION MANUAL THOROUGHLY AND UNDERSTAND REQUIREMENTS FOR OPERATION, INSPECTION AND MAINTENANCE BEFORE STARTING THE MACHINE. THE OPERATOR AND THE CONTROLLER OF THIS MACHINE MUST NOT ALLOW ANY PERSON WHO DOES NOT HAVE A COMPLETE UNDERSTANDING OF THE NATURE OF THIS MACHINE TO OPERATE IT. SAFETY REMINDER TO ALL HAMADA OPERATORS Your Hamada Press has been designed and built to be safe to use as a machine can be. But there is a hazard in any moving machinery, whatever it's purpose. All ‘who operate machinery must be aware that injury may occur if hands or fingers are put into it while it is running To protect the careless and inattentive person, so far as itis possible to do, covers have been installed over chain delivery, roller, and cylinder areas, in most cases a micro-switch is activated when covers are lifted, and that tums off the machine. Guard bars have been installed at points of possible hazard. Gears have been covered by side panels. For your own safety, do not remove any side panels, safety covers, or safety bars. Do not disconnect or manually defeat any switches designed to cut on power to the press in the event that a safety cover or device is removed. While all possible measures have been taken to prevent injury, in the final analysis it is you who will keep you from hurting yourself, by being alert and watchful, by turning off the press before making adjustments, and by "keeping your fingers to yourself.” Yours for safe and happy operation - HAMADA, NOTICE THE WARRANTY ON THIS HAMADA PRESS BECOMES INVALID IF ANY OF THE SAFEIY FEATURES OR DEVICES ARE REMOVED, CHANGED OR DISCONNECTED.Basic Safety Rules General + Operators and maintenance personnel must read this manual carefully before operating or do maintenance on the press. + Keep this manual handy so you can reference information when needed. + Do not operate or do maintenance on the press until you have a thorough understanding of all the operations. * If you loose or damage this manual, contact us or your local HAMADA dealer to order a new copy. * Ifyou transfer the press to someone else, attach this manual for the new owner. * Tum OFF the machine power switch before servicing the machine to prevent electrical accidents. + After servicing a press, make sure all safety guards, shields, indicators, and all other safety equipment are replaced and in proper operating condition before allowing an operator to operate the press. ‘+ Make sure hands, fingers, and other appendages of all persons near the press are clear before rotating the press. Clothing and dress ‘+ Do not wear jewelry, loose clothing, long nails, or wear long hair. Wear a hat or other covering to keep your hair tight to your head: dangling hair is dangerous! + Wear a work jacket with the cuffs and collar tightly closed. + Wear work pants with the hems tightly closed. + Wear shoes with a non-slip sole. Fire + When a fire breaks out, attempt to extinguish the fire before it expands, and promptly contact the fire department. If an oil, chemical, or electrical fire breaks out use only an extinguisher approved for that particular type of fire. Never use water to extinguish these types of fires. Ifan accident does occur ; *Call for help in a loud voice. Ifa part of your body gets caught in a rotating part ; “Turn OFF the power supply ita part of your body gets caught between the ink or dampening rollers ; “Remove the rollers. Ita part of your body gets caught between cylinders ; + manually remove the pressure from the cylinders.18252 Series SERVICE MANU: Potential Hazards — Read Carefully! The most important concept to keep in mind when operating the machine is safety; think safety first! This section describes the basic warnings for printing press operation and maintenance. Please read it carefully and heed the warnings. Waste Do not remodel the press. Doing so may void the warranty and create an unsafe machine. Do not remove safety covers or bars. Doing so may cause death, serious injury, or to damage the press. Do not touch rotating or driving units of the press while it is running. Always stop the press first when you do an operation near these areas. When you operate the press together with other people, always verbally confirm each person is clear before operating the press. Most of the solutions used for printing and prepress contain chemicals harmful for human bodies. Read and follow the instructions and cautions on the label. Use a blanket cleaner made exclusively used for printing presses. Using a volatile solution, such as gasoline, may cause a fire or explosion. Do not dispose of waste liquids or oil in a sewer drain. Contract an industrial waste collection service, or dispose of the waste according to the local anti-pollution ordinances.Series SERVICE MANUAL The current load in the press may cause a fire while the press is not running. Always turn OFF the source power supply (power circuit breaker switch) when the press is not in use. When you do another operation after inching, first release your finger from the inching switch. Never do another operation while pressing an inching switch. Always turn OFF the source power supply (power circuit breaker switch) before doing maintenance operations or adding oil. After maintenance or repair, always return safety components, such as safety covers, safety bars, and protection units, to their normal status. Gasoline It a fire breaks out, attempt to extinguish the fire before it expands, and promptly contact the fire department. Keep a fire extinguisher near the press so you are prepared if a fire breaks out. During a lighting or thunder storm, turn OFF the source power supply (power circuit breaker switch) to prevent damage to the machine's electrical circuits. ‘Turn OFF the power circuit breaker switch also when you finish operating the press. Use only cleaning solutions manufactured exclusively for cleaning printing press components. Do not use a highly volatile cleaning solution such as gasoline. The use of such solutions may cause a fire or explo:VICE MANUAL Contents 1. ELECTRICAL INFORMATION .. [1] Electrical specifications. [2] Adjustment of rotary switches and dip switches on main board. [3] Program check mode... [4] Timing data seuing [5] Adjustment of fountain roller minimum rotation speed setting ....snoes 1 2. INVERTER SETTING. {1] Environment setting {2} Setting and changing parameters... [3] Initializing the set value ...... [4] Inverter trip display... [5] Operation by operator. [6] Data [7] Inverter data table... 3. EACH SENSOR ADJUSTMENT [1] Adjustment of dampening water detection board [2] Adjustment of double sheet detection [3] Adjustment of skew detection sensor.. 4. TIMING CHART [1] Impression [2] Form roller function and paper feeding start during automatic operation seve 30 [3] Feeding stop and form roller function after count-up during automatic operation...... 31 [4] Blanket washing... [5] Feeder table up air cylinder valve relay... [6] Delivery table down air cylinder valve relay..... [7] Skew detection... [8] Swing jam, [9] Blanket jamSeries SERVICE MANUAL EPS TIMING CHART U1] Plate mounting ... [2] Plate removing ..... 13] Skew adjustment [4] Moving forward the tail edge side clamp.. TROUBLESHOOTING. [1] Phenomenon in case a fuse is blown... [2] Preparation switch LED does not light. [3] Machine does not rotate... [4] Pump motor does not operate... [5] Feeder table up motor does not operate. .... [6] P-B and B-1 impressions do not come on. ... [7] Feeder clutch does not operate. [8] Feeder table does not go up...... .. 56 19] When feeder clutch is engaged and pump is started, paper feeding starts and cannot be stopped... 60 [10] Paper feeding cannot be started... [11] Each form roller cannot be operated. (12] Each ink ductor solenoid does not activate. .. [13] Dampening motor does not operate. .. [14] Delivery table does not descend [15] Spray valve does not activate... [16] Blanket washing valve does not activate. [17] Blanket washing pump does not operate. [18] Air selector valve does not activate. .. [19] Jamming is displayed when a jamming is not occured. [20] EPS does not operate properly. [21] Check on sensors. [22] Check on magnet switches. (23] Check on inverter.....Series SERVICE MANUAL, ELECTRIC WIRING DIAGRAM CONTROL BOX CONNECTIONS - oe DAMPENING MOTOR CONNECTIONS... . eee) CPU BOARD INPUT CONNECTIONS .. oe sen snnaennes 93 MAIN BOARD OUTPUT CONNECTIONS... sestnsee . oF MAIN BOARD CONNECTOR TABLE Sot eo sseneneees 9S 1/0 BOARD INPUT CONNECTIONS 96 VO BOARD OUTPUT CONNECTIONS . 97 VO BOARD EPS INPUT/OUTPUT CONNECTIONS. 2 8 VO BOARD CONNECTOR TABLE... cone 99 FEEDER SIDE OPERATION PANEL CONNECTIONS. . 100 DELIVERY SIDE OP-S OPERATION PANEL CONNECTIONS. 101 DELIVERY NOP-S OPERATION PANEL CONNECTIONS ... wo. 102 NOP-S OPERATION PANEL CONNECTIONS 103 OP-S UPPER OPERATION PANEL CONNECTIONS... 104, OP-S LOWER OPERATION PANEL CONNECTIONS. 105 EPS OPERATION PANEL CONNECTIONS. 106 DATA SECTION... 107 Note: NON-OPERATION SIDE that describe in this manual means "MOTOR DRIVE SIDE"ELECTRICAL INFORMATION1, ELECTRICAL DATA 1. ELECTRICAL INFORMATION [1] Electrical Specifications Electric capacity DKVA (458) Main motor 3.7KW Pump moor 0.75KW Inverter T200/220V ( Yaskawa Electric: VS-616G5) NOTE: This inverter isa low noive type inverter, Malfunction may occur ifa round fault circuit breaker produced prior to 1982 is used. Use the following products to prevent higher harmonic problems, * Mitsubishi Electric Corp.: NV series (Produced after 1988) NVS0-CP(S0A) NVS0-SP(S0A) NVS0-HP(SOA) NV50-SEP(SOA) NVS0-HEP(SOA) * Fuji Electric Co.: EG, SG series (Produced after 1988) * Matsushita Electric Works Co.: Ground fault circuit breaker (Produced after 1988) Standard power source 3-phase 200V. ov18252 Series SI RVICE MANUAL, fe SOOO) oO z ‘ip switch Rotary switch Rotary Switch Rotay SW no Description Functions S6 0 | Standard Used to set the switch to this position in normal condi- T | Skew detection sensor Set to invalidate dhe skew detection incase the skew de invalid mode tection fibers failed, 2 | Paper detection sensor Set to invalidate the paper detection sensor and substi invalid mode tute withthe skew detection fiber in case the fron ay sensor is failed. | 3-_|Swing jam sensor invalid mode] Set wo invalidate the swing jam. 4 | Blanket jam invatid mode | Set to invalidate dhe blanket jam, 5 | Delivery able lowering | Setto top lowering of delivery table automatically. invalid mode 0 | Standard ‘Normal printing condition 1_| Program check Set to check the relay numberof the program. ss 2 | Data input mode Set to sett this position before entering data 4 | Dampening fountain roller | Adjustment wo rotate the fountain roller slowly in when adjustment seting the fountain speed volume set at "0" positon Dip Switch (S2) Dip SW No. Statement B252 data 1 ‘Speed of communication with sub CPU board OFF 2 OFF 3 ON 4 Speed on high speed side ON 3 OFF - 6 Mode OFF 1 ON 8 Start mode OFF1 ELECTRICAL DATA [3] Program check mode WO board can be checked from the main CPU board 1 Method of operation (1) Set the rotary switch $8 t0 1 (2) Set the 3digit digital switch (S3.S4.85) (3) Check ON/OFF with the yellow LED on the left side. 2. Communication error check Set the 3-ligit digital switch to 250 and verify that the yellow LEDs 12.14.15 are illuminated. If not, ‘check the following. 250-12 UO board 250-14 DELIVERY NOP-S OPERATION PANEL 250-15 DELIVERY OP-S OPERATION PANEL, INPUT Dial sw] Yee Description Wire No | Reman] EER Para 002 o_| TEN KEY7 |_| TEN KEY 8 2 | TENKEY9 TEN KEY 4 TEN KEY 5) TEN KEY 6 TEN KEY | TEN KEY 2 003, ‘COUNT BUTTON, CYCLE OUT (STOP) BUTTON. 2P DAMPENING FEED SPEED UP BUTTON IP DAMPENING FEED SPEED UP BUTTON 005 DAMPENING FEED AUTO SPEED UP SETTING BUTTON SPRAY TIMING BUTTON 006 |_| 2PINK DUCTOR AUTO BUTTON IP INK DUCTOR AUTO BUTTON TEN KEY 3) TEN KEY 0) TEN KEY CLEAR ‘TEN KEY ENTRY. WASHING SET BUTTON DRY SET BUTTON IP MANUAL DAMPENING FEED BUTTON 2P MANUAL DAMPENING FEED BUTTON IP AUTO DAMPENING FEED BUTTON 2P AUTO DAMPENING FEED BUTTONRVICE MANUAL 009 (© _| IP MANUAL INK BUCTOR BUTTON | L ] __| 7 |2P MANUAL INK DUCTOR BUTTON Tt __ os. 0 | PREPARATION BUTTON (DELIVERY) | [71 7'START BUTTON (DELIVERY) | 2_| STOP BUTTON (DELIVERY) 3__| FORWARD INCHING BUTTON (DELIVERY) 4 BACKWARD INCHING BUTTON (DELIVERY) | 021 3_| cocover 240 LD24 '3_| OPSCOVER-1 X155 LD6 a2 | 0 | OPSCOVERS x57 LD 1 | OP-S COVER? | xise Lis [2 SPSAFETY BAR X16) LDIs 3 _| IP FEEDER SIDE COVER x160 Tie 4 | IP OP-S EMERGENCY BUTTON xia) or S| 3P OP-S EMERGENCY BUTTON x7 LDIi6 © | IPNOP-S EMERGENCY BUTTON x105 Li 7_[2PNOPS EMERGENCY BUTTON xn L128 023 | _0_| 3P PLATE CYLINDER COVER XI35 29 T_| NOP-SCOVER xi28 [ps0 3 _| 2PINK UNIT COVER xia4 LD32 4 _| IPPLATE CYLINDER COVER x132 LD33 Ss IP INK UNIT COVER X131 [ups 6 _| IPSAFETY BAR X130 LD35 7_| SWING JAM SENSOR xi5s0_| 1LD36 024 0 __| FEEDER RISING LEVER OFF DETECTOR xi47_ | LD2s 1_| POSTCARD SETTING SW x13 | LD26 2__| FEEDER TABLE BOTTOM LIMIT xi37 LD27 3__| FEEDER TABLE RAISING STOP SENSOR x44 LD28 [4 [DOUBLE SHEET DETECTOR (MECANICAL) | _X146 Ly 5__| FEEDER PAPER HEIGHT DETECTION SENSOR) _X145 [ibis 6 _| FEEDER TABLE UPPER LIMIT SW [x36 i) 7_| DELIVERY TABLE BOTTOM LIMITILEAD MAGNET) SW _|_X239 [p20 26 o_[cosam | x21 | Lbs 2__| CONVEYER COVER | xis3, | Lb 3__| 1P-2P IMPRESSION CYLINDER COVER [x16 _| [pi 4 DELIVERY TABLE HEIGHT SENSOR. X250 [it 5__| IP DAMPENING WATER DETECTOR X165 | [D2 6 _| 2 DAMPENING WATER DETECTOR | X166 [ps 027 0_| IPOP-S PREPARATION BUTTON. XU LD104 Lo 1P_OP-S FORWARD INCHING BUTTON Txug LDI07 L_2 | 1Pop-S BACKWARD INCHING BUTTON X120 | LDIO9, 4 ~ aELECTRICAL DATA 1 [3] PMANUALINE pucToR sw ~DX Din 4 | IP MANUAL DAMPENING FEED SW xi2 Ls 5 _| 2P OPS PREPARATION BUTTON xi38 Lov? | 2 OP:S FORWARD INCHING BUTTON I “L100 7 [2h OPS BACKWARD INCHING BUTTON | XI2s L102 es [2 | 2P MANUAL INK DUCTOR sw Lxta6 Lo | 4_ [2 MANUAL DAMPENING FEED Sw xi27 p93 4 [PINK FORM ROLLER MANUAL SW xia Lous 5 | 2PINK FORM ROLLER MANUAL SW xnis bias 6 IPDAMPENING FORM ROLLER MANUAL SW | XUIA Lo? 7__| 2° DAMPENING FORM ROLLER MANUAL.SW xiI6 Liss 29 |_2_| 2PNOP-S BACKWARD INCHING BUTTON | X109 Lbs {| 2P MANUAL IMPRESSION SW xi10 LDss 4 | 2PNOP-S PREPARATION BUTTON X06 Loe 5__| 2P NOP'S P, CYL. POSITION BUTTON xi07 Los | 2PNOP.S FORWARD INCHING BUTTON | xi08 Las GO [0 | IP NOP-S PREPARATION BUTTON xi00 37 1 LIPNOP:SP. CYL. POSITION BUTTON xi01 38 2 IPNOP.S FORWARD INCHING BUTTON | xi02 1LD39 3. [IPNOP.S BACKWARD INCHING BUTTON | x03 p40 | 1P MANUAL IMPRESSION sw xi0e Lai G80 |_0_| 2° EFS PLATE INSERTION BUTTON xis Liss |__| 29 EPS PLATE EJECTION BUTTON Xxi8s LDinz 2 _ | 2P EPS START BUTTON XxI86 Lois! 3_| 2P EPS SKEW BUTTON xi87 L130 4 | 2P EPS RESET BUTTON x88 List 5_| 2P UPPER SIDE CLUTCH AIR-CYLINDER ON | xI73 LDi36 | 2P UPPER SIDE CLUTCH AIR-CYLINDER OFF | xI74 Liss 7 2P DOWN-SIDE CLUTCH AIR-CYLINDER ON X175 |LDIs4 Oe [0 IPEDS PLATE INSERTION Sw (SELECTOR SW] _X179, List 1__ [PES PLATE EJECTION SW SELECTOR SW) | xI80 Liss 2 _| IPERS START BUTTON X81 Love 3_| IPERS SKEW BUTTON xi82 Loui 4 [IPEDS RESET BUTTON X88 LDi24 5 | IPUPPER-SIDE CLUTCH AIR-CYLINDER ON |_XI67 Los 6 | IP UPPER-SIDE CLUTCH AIR-CYLINDER OFF | X68 ‘upi22 7 [IP DOWN-SIDE CLUTCH AIR-CYLINDER ON | X169 uprai 082 oO 2P DOWN-SIDE CLUTCH AIR-CYLINDER OFF | X176 [Lpi40 1] 2PLARGE AIR-CYL, SENSOR (EXTENDED) | X177 L139 2 | 2P LARGE AI-CYL. SNSOR (CONTRACTED) |_XITR Liss 5 [iPDoWNSIDE CLUTCH AIR-CYLINDER OFF —_—_|_xi70 Loion [4 F AIR-CY1. SENSOR (EXTENDED) | X71 LDR6_ 5_| IPLARGE AIR-CYL. SENSOR (CONTRACTED) | _x172 107 |__| EMERGENCY STORSUB-CONTACTPOINT FOR MG!) | xo24 1_| PUMP THERMAL Li 2 INVERTER TRIP _ X027 Lut 3__| FEEDER TABLE UP/DOWN MOTOR THERMAL _|_x026 L2 110 |_0_ | RIGHT SKEW DETECTOR SENSOR x008 sis 1_ | °O°POSITION BASE SENSOR X008 SL 2__ | LEFT SKEW DETECTION SENSOR xo10 sua 3__| DOUBLE SHEET DETECTOR Xou1 4_| PAPER DETECT SIGNAL xor2 @_| BLANKET JAM SENSOR x44 7__ | IPPLATE CYLINDER BASE SENSOR XO15 11a [_2 _| STOP BUTTON (FEEDER) x01 3_| START BUTTON (FEEDER) x002 LB 114” [2 _| PREPARATION BUTTON (FEEDER) x003 B 3 _ | FIXED POSITION BUTTON (FEEDER) x00 a 4_| FORWARD INCHING BUTTON (FEEDER) X005 5 3_| BACKWARD INCHING BUTTON (FEEDER) | x006 16 @_ | EMERGENCY STOP BUTTON (FEEDER) 007 u 11s |_5_ | FEEDER TABLE RAISE BUTTON 030 Ls 7_ | MANUAL SELECT BUTTON X039 Lis 16 |_0_| FEEDER TABLE STOP BUTTON X01 Lis 1_ | FEEDER TABLE LOWER BUTTON X032 Lie 2_| AUTO FEED BUTTON X033 Li 3_| FRONTLAY MANUAL BUTTON X034 Lis 4_| FEEDER CLUTCH BUTTON X035 LI, $_| DOUBLE SHEET DETECTION BUTTON X036 120) 6 _| FEEDER START BUTTON xox? La 7_| PUMP BUTTON X08 2 120_| 0 _| 2PPLATE CYLINDER BASE SENSOR X016 sL33| ELECTRICAL DATA, OUTPUT [Digitaisw | Yelow | Description Wire No.| Remark] LE OR wo |__| COUNT BUTTON LED CYCLE OUT (STOP) BUTTON LED [TEN KEY ENTRY LED __ _ [7 3__[ WASHING SET BUTTON LED [4 DRY SET BUTTON LED 7 5__| IPMANUAL DAMPENING FEED BUTTON LED 6 _| 2P MANUAL DAMPENING FEED BUTTON LED oor |_1_| 1PAUTO DAMPENING FEED BUTTON LED. 2_| 2P AUTO DAMPENING FEED BUTTON LED 5_| IP MANUAL INK DUCTOR BUTTON LED | 2P MANUAL INK DUCTOR BUTTON LED 003 | _1_| IPAUTOINK DUCTOR BUTTON LED 2_| 2P AUTO INK DUCTOR BUTTON LED 5_| SPRAY TIMING BUTTON LED 6 _| DAMPENING AUTO SPEED UP SET BUTTON LED 010 [_1_| START BUTTON LED (DELIVERY) 2_| PREPARATION BUTTON SW LED (DELIVERY) 031 | 0 | FEEDSOL Yiis LD78 3_| SPRAY VALVE y232 LD83 4__| 1POP-S EMERGENCY STOP BUTTONLED | Y107 L120 5__| 2POP-SEMERGENCY STOP BUTTON LED | Y108 LDIIT 6 _ | IPNOP-S EMERGENCY STOP BUTTONLED | 103 LD60 7_| 2P NOP-S EMERGENCY STOP BUTTONLED | Y106 LD63 032 | _0_| 1PNOP-S PREPARATION BUTTON LED. Yi01 LDe2 |_| IP P.CYLINDER POSITION BUTTON LED Y102 LDer 2__| 2P NOP-S PREPARATION BUTTON LED Yi04 LD6s 3__| 2P CYLINDER POSITION BUTTON LED 105 LD6# 4_| BLANKET WASH PUMP. Yn7 Lbs? 3_| EPS BRAKE Y218 LD66 033 | _0_| IPINK DUCTOR SOL ¥130 Lbs! 1_| 2P INK DUCTOR SOL YisI LD80 2_| STATIC ELIMINATOR BUTTON LED ¥233 LD79 4_ | PMANUAL DAMPENING FEED BUTTON LEDiwxranen |_YIT LDS '5_ | SPMANUAL DAMPENING FEED DUTTON LEDweasen | YI LD103 034 |_0 | 1POP-S PRERARATION BUTTON LED Y109 Lb110 1_[ [PINK DUCTOR BUTTON LED (NK PANEL) | YI0 D106 2_ | 2P OP-S PRERARATION BUTTON LED yin LD99 3__| 2PINK DUCTOR BUTTON LED UNK PANEL) | Y113. LD%MANUAI 036 FEEDER CLUTCH VALVE LD FEEDER TABLE RAISE VALVE LD? IP INK FORM ROLLER ON/OFF VALVE Lon 3_| IPDAMPENING FORM ROLLER ON/OFF VALVE | YI23 4__| 2P INK FORM ROLLER ON/OFF VALVE Yio4 Lb74 5__| 2PDAMPENING FORM ROLLER ON/OFF VALVE | 125 Lb7s 6 _| 1PBLANKET WASH VALVE ¥i26 LD76 7_| 2P BLANKET WASH VALVE vir 7? 083 | 0_| IPLARGE AIR-CLYNDER VALVE (EXTENDED) | Yi34 LD90 1_[ }PLARGE AIR-CLYNDER VALVE (CONTRACTED) |_YI35 Lbs? 2__| IPUPPER-SIDE CLUTCH AIR-CLYNDER VALVE | Yi36 Lb 3_| 1PDOWN-SIDE CLUTCH AIR-CLYNDER VALVE | _YI37 Loo 4_| IPRETAINING ROLLER VALVE vie LD9s 5_| 2PLARGE AIR-CLYNDER VALVE (EXTENDED) _| 139 LoIo 6 _| 2PLARGE AIR-CLYNDER VALVE (CONTRACTED) | 140 LDIO5 7__| 2 UPPER-SIDE CLUTCH AIR-CLYNDER VALVE | Yai LDI08 084 [0 | 3PDOWN-SIDE CLUTCH AIR-CLYNDER VALVE | Y142 Lbui7 1_| 2P RETAINING ROLLER VALVE vias Louis 2_| IPEPS START BUTTON LED Yia6 Lbi20 3_| 2PEPS START BUTTON LED 187 Lous 6 _| AIR BLOWER VALVE ¥i28 Lbs 7_| DBLIVEY TABLE DESCENT VALVE yi29 Lbs 108 |_0_| START BUTTON LED (FEEDER) Yooi 155 1_| PREPARATION BUTTON LED (FEEDER) Yoo 136 2_| FIXED POSITION BUTTON LED (FEEDER) | ¥003 137 3_| EMERGENCY STOP BUTTON LED (FEEDER) 106 | _0_ | MANUAL SELECT BUTTON LED your a7 1_| FEEDER TABLE STOP BUTTON LED You0 a8 2_| AUTO FEED BUTTON LED Yost a9 3_| FRONTLAY MANUAL BUTTON LED you 130 4_| FEEDER CLUTCH BUTTON LED yous Ls S DOUBLE SHEET DETECTION BUTTON LED YO Ls2 6 _| FEEDER START BUTTON LED Yous 133 7_| PUMP BUTTON LED Yous Ls4 108 | 0 | FRONTLAY SOL Yost 13 1_| GRIPPER OPEN/CLOSE SOL you 12a 4_ | IPDAMPENING MOTOR sTRi 192 5 2P DAMPENING MOTOR: STR2 L93 109 | 0 | PUMPMAGNET Yoo! SLI? 1__ | FEEDER TABLE RAISE MAGNET SW Yoos [Suis 2__|[ FEEDER TABLE LOWER MAGNET SW 006 Su91, ELECTRICAL DATA iw |__| BUZZER You? S120 + | COUNTER | Yoo SLI 5 COUNTER 2 YOO SL22 | [6 _| COUNTER OUTPUT ‘You SL23 111 |_0_| 1PP-B IMPRESSION VALVE ‘you su |_| 1PB-TIMPRESSION VALVE Yous si2 2_| 2PP-B IMPRESSION VALVE You sui 3_| 2PB-1 IMPRESSION VALVE Yous SLa 6 _| DOUBLE SHEET TIMING yous su? 7_| DOUBLE SHEET RESET ‘yors SLs mm | 6 | MELODY? ‘yo3s 7_| MELODY 2 Yost 117 |_0_ | FORWARD INCHING ¥026 LI |_| BACKWARD INCHING you? 132 2_| MULTI SPEED 1 aNV) ‘Yo2s, 133 3__ | MULTI SPEED 2 (NV) ‘yo29 ey 4_| MULTI SPEED 3 (NV) 030 135 | CHIME 03s, [4] Timing data setting Data input method Set the rotary SW $8 10 2. T ress the clear key of the delivery OP-S operation panel to light the entry key LED. Enler the data number using the ten key. T data atthe right side of the printed paper count display unit. ‘When the entry Key is pressed, the data number will be displayed atthe left side and the present 1 Enter new data using the ten key. and press the entry key. Is data entry completed ? No YES Enter 99 using the ten key, and press the entry key. I [-Setthe rotary SW_S8 to 0.B252 Series SERVICE MANU DATA TABLE. (Description IP P-B TIMING 1p B-1 TIMING - IP DAMPENING FORM ROLLER TIMING IP INK FORM ROLLER TIMING IP BLANKET WASH TIMING 2P P-B TIMING. 2P B-1 TIMING 2P DAMPENING FORM ROLLER TIMING “2P INK FORM ROLLER TIMING 2P BLANKET WASH TIMING. FEEDER TABLE UP TIMING PAPER FEED TIMING SWING JAM TIMING DOUBLE SHEET TIMING _ SKEW DETECT TIMING. PAPER DETECT TIMING BLANKET JAM TIMING (CLUTCH TIMING ‘SPRAY ON TIMING ‘SPRAY OFF TIMING PAPER SET POSITION (CONVEYOR) PAPER SET POSITION (FRONT LAY) PAPER SET POSITION (SIDE JOGGER) PAPER SET POSITION (BACK JOGGER) PLATE CYLINDER POSITION STOP (iP LEADING EDGE) PLATE CYLINDER POSITION STOP (IP TAIL EDGE) PLATE CYLINDER POSITION STOP (2P LEADING EDGI PLATE CYLINDER POSITION STOP 2P TAIL EDGE) PAPER FEED STOP COUNT. BLANKET WASH TIMER BLANKET WASHING SOLVENT SPRAYING TIMER BLANKET DRYING TIMER DAMPENING FEED AUTO SPEED UP TIMER IP D. FOUNTAIN ROLLER MINIMUM SPEED ADJUSTMENT SETTING 2P D. FOUNTAIN ROLLER MINIMUM SPEED ADJUSTMENT SETTING AUTO DAMPENING SPEED UP (4000) _ ‘AUTO DAMPENING SPEED UP (5000) AUTO DAMPENING SPEED UP (6000) ‘AUTO DAMPENING SPEED UP (7000) AUTO DAMPENING SPEED UP (8000) AUTO DAMPENING SPEED UP (9000) AUTO DAMPENING SPEED UP (10000) & £ & g zIPTAIL EDGE POSITION STOP TERS IP BACKWARD LEAD SP LEADING EDGE POSITION STOP BP TAIL EDGE POSITION STOP” TES 2P BACKWARD LEADING EDGE POSITION STOP COUNT, Note! [5] Adjustment of fountain roller minimum rotation speed setting LS sass 0000 9000 2900 8900 i eoeeeeee [|] 6 Dip switch Rotary switch Method of adjustment 1. Set the metering roller to the fountain roller. (Printing condition) Set the rotary switch(S8) to 4 Press the manval dampening button, then press the cycle out button(stop button) after setting 1/2P fountain speed volumes to "0 4, Rotate the the fountain roller to turn each fountain roller volume of 1/2P clockwise, 5. Tum each fountain roller volume of 1/2P counterclockwise slowly, and adjust the fountain roller ‘volume to equal the minimum rotation speed of 1/2P. 6. Press the cycle out button(stop button) to be memorize the adjusted minimum rotation speed. 7. Set back the rotary switeh(S8) to 0 8. Be sure to verify the the fountain roller minimun rotation speed at position of the fountain roller volume. Note: Be sure to adjust the item(3} ahove for correct seting. Be sure to make the adjustment of /2P simultaneous.INVERTER SETTING2. INVERTER SETTING (Yaskawa Electric Corp.: VS-616G5) [1] Environment setting (A1-**) Operation procedure 2. INVERTER SETTING [cy Press the IMENUT Key Mode selection sereen will be displayed. (G5 Main Menu # Operation. (2) Press the | A] key once. ~ Select the environment setting mode. (Display unit displays the environment setting mode.) G* Main Menu * Initialize, ‘avsice. played, (When pressed twice, the control ‘mode will be displayed.) (3) Pres the “Language selection sereen willbe =e [DATA/ENTER] key. displayed. pareaniaee English (@) Press the [A Key once “The present access level willbe dis- ‘Access evel QUICK-START, (5) Press the [DATA/ENTER] key. ++ The constant change sereen will be displayed AL-Ol=2 =# QUICK-START. (6) Press the [ A] key twice. ++ Select the constant. Alle 4 ADVANCED (7) Press the [DATA/ENTER]—-** key. Write the set value. Entry Accepted (8) Press the [MENU] key. ” Display (1) Mode selection sereen. GS* Main Menu * Operation (9) Press the [DATA/ENTER] key ++ The frequency monitor sereen will be displayed. Frequency Ref 7? UL-01=00.00HZ, * If the inverter is in the initial state, parameters that can be set are restricted. Be sure to set the access level {AL-01) in the beginning * When the control mode is changed, some parameters will be changed accordingly. Be sure to set the control mode (A1-02) in the beginning. BSERVICE MANUAL [2] Setting and changing parameters (Setting other than A1-"*) Operation procedure [11 Press the IMENUI key. The mode selection sere displayed. Operation (2) Press the | Al key twice. I Select the program mode. (The message "Program mode” will be displayed on the (G5* Main Menu * display unit Programing (3) Press the “~The mode selection seen willbe aa IDATA/ENTER] key. displayed Application (4) Pres the [ A] Key several =-Select the group. (b through 0) (The ea times present sr0Up will be displayed inthe display unit.) Tuning (5) Press the “The constant reference seen willbe eT IDATA/ENTER] ke displayed. * mye Accel/ Decel (6) Press the “+ Select the constant ‘Accel time 1 [DATA/ENTER] key C1-01=10.0See (7) Press the “+The constant change screen will be —— [DATA/ENTER] key. displayed oo100See (8) Pressthe [PRESET] key. --Moving of digits a Pressthe [A] key several --+Changing of numere values (The portion Gers that flickers isthe portion to be changed.) I (9) Press the [DATA/ENTER] key. “++ Write the set value. Entry Accepted For making other set To retum oe step ress the [ESC] key —! (10) Press the [MENU] key. “++ Select (1) Mode selection screen, GS* Main Menu * Operation (11) Press the IDATAVENTER] key. “+The frequency monitor sereen will be displayed, Frequency Ref U1-01=17.00H2[3] Initializing the set value Operation procedure 2. INVERTER SETTING [isp INENUIbs “The mode selection sereen will be displayed G5* Main Menu ° Operation (2) Press the | [key once. Select the environment setting mode. (Environment setting mode” will be displayed in the display unit.) (G5 Main Menu * Initialize (G) Press the [DATA/ENTER| ‘The language selection serven will be Select Language key. displayed my English (4) Press the | | Key three. ~The initialize selection screen will be dis-| nix Parameters times. played. . No Initialize. (5) Press the [DATA/ENTER| ‘The initialize change screen will be ‘Ale 00 ey displayed. * mms No Initialize. (6) Press the [A] Key once. Select the constant ‘A1-0362220 2-WIRE Initialize I (7) Press the [DATA/ENTER] key ‘Write the set value. Entry Accepted. (8) Press the [MENU] key Select (1) Mode selection screen. (GS* Main Menu * Operation (9) Press the [DATA/ENTER] “+ The frequency monitor sereen will be Frequency Ref key. displayed. UL-01=17.00H2.[4] Inverter trip display 1282 Series SERVICE MANUAL, 1) Display and contents of inverter trip Display L Content Check point 0c Overcurrent ‘Check for sudden change in ov Overvoliaze ‘Cheek for sudden change in load out (Overload (motor) ‘Check for overload O12 Overload (inverter) ‘Check for overload, cPFOI 1 CPU abnormal Inverter abnormal cPFOS Operation procedure 2) History of abnormal content (1) Press the [MENU] key. “++ The mode selection sereen will be displayed, G5* Main Menu * Operation j J (2) Press the ++ The frequency monitor screen will be a [DATA/ENTER] key. displayed. eel UL-01=17.00H12 (3) Press the [A] key several +++ The function selection U: et times. history) sereen will be displayed. Funetion U3 Fault history (4) Press the + Abnormal content of one step before will = IDATAV/ENTER] key. be displayed. | ot i (5) Press the [A] key once. +++ The abnormal content of two steps before ‘will be displayed, Fault Message 2 “There are no abnormal contents as well of 3 and 4 steps before, (6) Press the [MENU] key. + Select (1) Mode selection sereen, (G5* Main Manu * Operation 1 (7) Press the [DATA/ENTER] key. ++ The frequency monitor screen will be displayed Frequency Ref ? U1-01=17.00HZ2. INVERTER SETTING [5] Operation by operator Operation procedure (1) Press the ILOCALIREMOTE] key. (REMOTE LED (SEQ.REF) will xo out and DRIVE. FWD will light.) Frequency Ref UL-01=0.0042) J (2) Press the IDATA/ENTER] key. +++ The trequeney change sereen will be displayed Frequency Ref (000.0082 i (3) Press the [>RESET] Press the | A] key several times. (Example: 15Hz) +++ Moving of digits ++» Changing numeric values: (The portion that flickers isthe portion to be changed.) Frequency Ref 015.0082 (4) Press the [DATA/ENTER] key. + Write the set value Eniry Accepted ? (5) Press the [ESC] key. “The frequency monitor screen will be displayed. Frequency Ref UI-01=15.00H2Z (©) Press the [RUN] key. + The machine runs atthe frequency set by Frequency Ref the motor. UL-01=15.0082 (7) Press the [STOP] key. +++ Motor stops. Frequency Ref UI-01=15.00HZ (8) Press the +++ The frequency change sereen will be Frequency Ref [DATA/ENTER] key. displayed. oreo (9) Press the [>RESET] key. +++ Moving of digits a Press the [ A] key several Changing numeric values (change to 0) (The por ‘ono oor. times. tion that lickers isthe portion o be changed.) I (10) Press the IDATA/ENTER] key. + Write the set value Entry Accepted ? (11) Press the [ESC] key. “+The frequency monitor display screen will be displayed. Frequency Ref U1-01=0.0082 (12) Press the {LOCAL/REMOTE] key. “+ (REMOTE LED (SEQ, REF) light and DRIVE, FWD go out.) Frequency Ref url '=17.00HZ ”18252 Series SERVICE MANUAL [6] Data Functions Purana Deseription Setiea [Mearun] Plant [Hanae Wo Unt Selva 252 ALO [npr ciamrapaeeawun [ef 1 | 1 fa AL-O1 | Constant acess level 0-4 1 4 Mode [A1-02 | Usersting cosan 03 1 pyreta. [Comins A103 oon |_| a co oe AL-O4 | Pass ward 1 0000-9999 1 0000 | 0000 FaNr | AOS [raswnd3 000-9599 | | awe | emo te [anor Seting” [_— cont = = [-T- ma iO | Rebs iw ws 1 BIG _| Opes nts en = rs Operaing | 61-03 | Soni Heod enn 03 peo a b1-04 | Prohibition of reverse operation oO 1 oO 0 I-05 [operon esi ting ei] 0-3 peo 11-06 | Rel is twice 0 a 1.07 | opennccin air ising wma [0.1 bo Be 92-01 | tempest ‘0-1000_| amie] 0s | 0s braking 62-02 | DC injection braking current 0-100 1% 50 30 Dnt king tie wa 000-1000 [oor] 0.00 | oo 02-04 |e nn ing ie sp 00-1000 [oorss| 050 | 050 12-08 [ Mane x compensation oe 190 Spe [63-01 | Spee wacom tp a Thee searching 3-02 _| Speed search operating current 0-200 1% 150, 150 are {03 _[ spent sash ern te 01-100 | Oise] 20] 20 Timer [01 | Tine fton ON tine 00-3000 [oisee| 00 | 00 ae 4-02 _ | Timer function OFF-delay time 0.0-300.0 | O.1sec} 0.0 0.0 FID | v5.01 | PD soo mate eon ou Tpe pe control 55-02 Proportional gain (P) 0.00~25.00 | 0.01 | 1.00 | 1.00 1.03 | tl ine 0-260 [Oree| 10 | 10 04 [tg 10-1000 | 01% | 1000 | 1000 $05 | Bile) 00-100 [ore] 0.00 | 0.00 5.06 |b i 100-1000 | 01% | 1000 | 1900 35.07 | i te ames 1000-100] 01% | 00 | 00 1.08 [i pinay dy oe os 0100-1000 [O01] 0.00 | 0.00 vai _| 66-01 | Drel eaueny at stan o9-1000 [aie] 00 | 00 Functions "55-02 _| Dwell time at start 0.0-10.0 O.tsec | 0.0 0.0 6603 | Bwal feaueny at sop 110-4000 [one] 00 | 00 601 | Dwell ime at sop 10-100 | 0.1se] 00 | 00 Broop | 7-01 [Droop contra gain a0-1000- | 04% | 00 | 00 pec 7-02 _| Droop control delay time 0.03-2.00|0.0Isec]_ 0.05 | 0.05 182. INVERTER SETTING Appi [En bxO1 gain = 100 ve | xo | 80 OXTION [entra | 8-02 | Eneray saving feque 0.0-400.0 [01H | 0.0 | 00 Zero | BOOT | Zero servo gain 0-100 1 | 3 3 pee [ paa2 | Power completion wih oe [pe Pe FFUNING |Acceter- | C1-01 | Acceleration time 1 0.0-6000.0 | O.tsec| 10.0 [ 5.0 ation nd FCy-o2 | Declaration dine I oo-eo0.0 osec] 10.0 [30 tion time C93 | Acceleration time 2 _ 0.0-6000.0 [O.1see] 10.0 | 100 Ci-o4 | Deceleraion me 2 0.0-6000.0 [Osee] 10.0 | 100 1-05 | Acceleration sie 3 0.0-6000.0 [O.isee| 100 | 100 1-06 _| Deceleraion time 3 (00-60000 [Ise] 10.0 | 100 | C1-07_|_ Acceleration time 4 0,0-6000.0 | O.lsee | 10.0 | 10.0 C108 | Deceleration time 4 0.0-60000 [o.1see| 10.0 | 100 C109 | Emergency stop ime 0.0-60000 [0.1sec| 100 | 100 Cacao | Accel ce ime sting ont ol Ttado cua) aT me AE REWER Joos Tome] oo | oo Scuve | coor | S.Seleation stan 0.00-2.50 [oorsee| 020 | 0.20 femte- ["ca.02 | Supe shanti ime a (000-250 [ooisee| 020 | 020 tion aiog | Supe chara ine a (0.00-250 [o01see| 020 | 020 coon_| Scure carers tie a foorsee| 0.00 | 0.00 Slip | C301_| Slip compensation gain 01 | 00 | 00 wee” [€3-02 | Slip compensation primary delay time [0~10000 | msec | 2000 | 2000 (Motor €.a3 | Sip compensation imi 0-250 v% | 200 | 200 esis [carp Sipcompenion ion rR] be be G5_| Fox caleulaion method a tpPelo Forque | COI | Torque compensation gain 000-250 | 001 | 100 | a fembe cor”| Terrence [O-1m0 [Tse | 200 [5 C403 _| Start torque compensation forward roa 300 4.05 | Sta ome ost 20 ASR | CS.01_| ASR proportional (P) gain Too-30000] 001 | 20.00 | 20.00 C502 _| ASR integration (time 1 .00- 10.00 [o.oIsee| 0.500 | 0.500 5-03 | ASR proportional (P) gain? 00-30000] 0.01 | 20.00 | 20.00 5.04 _[ ASR integration (time 2 ‘2000-10000 [o0oIsec| 0.500 | 0.500 5.05 ASR mie 00-200 | 01m | so | 50 (5.06 | ASR primary delay time (0.000-0.500 [oooisec| 0.008 | 0.004 5.07 | ASR switching frequency o0-a000 | ote] 00 | 00 (5.08 | ASR integral (1) tit o-soo% | 1 | s00 | a00 Camier | C6-01_| Cartier frequency Upper limit [os-150 | one | 150 | 150 sem |p| ean een vee cane se 50 6-03 | Carer frequency gain 00-59 1 [0000 ‘hunting | C7-01 | Hinting prevention selection Oa ee Ton fune.| 7-02 | Hunting prevention gain 000-250 | 0.01 | 1.00 | 1.00 19B252 Series SERVICE MANUAL ‘Speed feedback deteetion Timit ime Carer frequency selection daring Frequency reference 1 Frequency reference 2 Frequeney reference 3 Frequency reference 4 Frequency reference 5 Frequency reference 6 Frequency reference 7 Frequency relerence 8 Jog frequency reference Frequency reference limit 100.0 Frequency reference lower limit 00 Jump frequency 1 00 Jump frequency 2 00 Jump frequency 3 00 Jump frequency width 10 ‘Frequency reference old function selection 5 ‘Torque control selection “Torque reference delay time ‘Speed limit selection Speed/orque control switching timer Input voltage seting ‘Vit pattern selection ‘Max. output frequency 200.0 60.0 Mid. output frequency 3.0 Mid. output frequency voltage 13.0 Min, output frequency 15 Min, output frequency voltage 35 Mid. output frequency 2 00 Mid_ output frequency voltage 2 00 00 Motor rated current (60HZ/50H2)) __|0.01-1500.0| 0.1 | 22.00 2.90 Motor no-load current 3.00 Number of motor poles2. INVERTER SETTING toot | 1.601 | FoF | Mowrlne-tline ance Tomo [o.oo MOTOR Ate Motor ak inductance ooo [oa [tea | aka [eonsant ‘Motoriron core nuatoncoetficenT 000-030 | 001 | 050 | 00 | Motor non core aatonceticiem 200075 | 001 | O75 | 07S Motor mechanical os oo-100 [ore] 00 | 00 | PG constant ‘o-oo [1 | 600 | 00 ST TGR A POT TC Gg st HERS] Open ton atmrermeel — poy a4 Eg ton lea a Eaton ——~gux ; 5 F105 | PG roaton a a pc yosy| FLO6 | PGdivison ae (PG pase onion —_t se conve | Fr-07 | REALS Name 1 rpete fing PG [ F108 | Overpeed detection evel ome pas | as ore F1:09 | Overpeed dteton delay ume 00-20 [01sec] 00 | 00 Fao] Eps Hest dein aecTON 9-50 aro Front} Eisen wped deviaan deion —qp-100 Tones] 05 [0S option Fi-i2 | Numer of PO peariceh | v0 | 1 | 0 | 0 I-13 | Number of PG gear teeth 2 Cr Fi-14 | PG open-circuit detection tine 00-100 [oiwe]| 20 | 20 AT] F201 | Bipolar oruni-poar input selection 01 fo | o [DI F¥01 | Digi inpat option 0-7 whe fe 01 | Chanel | monitor election = ee Analog. [F402 | Channel | gain 000-250 | 001 | 1.00 | 1.00 moni 7:03 | Channel 2 monitor elecion 13 ee Fa-04 | Channel 2 sain 000-250 | 001 | 050 | 050 O02 FF-O1 | Channel 1 outpr selection 0-37 ite le 5:02 | Channel 2 ouput selection 0-37 a D008 F6-01 | Output mode selection 1 0 0 |PO-36- F7-01__| Frequency multiple selection 1 1 1 H-01 | Multifunction input 1 erinal 3) 1 pee pas Hi-G2 | Mls function input’ ermal #) poe fs sequence] HOS | Mali-unction input 3 cermin! 5) rP3 ts input [ H-o# | Mul function input 4 enna 6) rte ps I-05 _| Multi-function input (erin! 7) rte ps TH-06 | Mul-anetion inp 6 (terminal 8) ris] s [conmot. [Sequence] 12-01 | Muli-funeton output erminas 9-10) rte fo CIRCUIT JouPet | F202 | Multi-function output terminal 25) 00-37 tat FUNCTION H2.03__| Multi-function output (terminal 26) 00~37 1 2 2 3-01 Signal eel selection erminal 13) 0. rhe fe 13-02 | Gain terminal 13) ‘o-10000 | 0.1% | 1000 | 100.0 \iapar® H3-03 | Bias (terminal 13) -100.0-+100.0) O.1% | 0.0 | 28.0 | 1-04] Signal level selection Germinal 16) 0.1 1 fo] o | H.05 | Mulfunetion analog input erminall6) 0-1F io [ae 212 |CE MANUAL 13.06 | Gain Germinal 16) o0-10000 | 0.1% | 100.0 | 1000 1307 | Bias Germinal 16) omen] as | oo | 00 Analog |_H3-08 | Signal level selection (terminal 14) [0.1.2 1 2 input ion analog input (terminal lh] 11 1 far [or 13-10 _| Gain Germinal 14) ~[o.0-10000 | 0.1% | 100.0 | 1000 | H311_[ Bias Germinal 14) =tooo-sion0 | 0.1% | 00 [00 15.12 _| Analog input filter ime constat 0,00-2.00 |o.0isec| 0.00 | 0.00 contro. HE-01_| Monitor selection Germinal 21) 1-33 P22 RAIA HL02_| Gain Germinal 21) 000-250 | oor | 1.00 | 1.00 FUNCTION | orion [-HS-03 | Bias enminal 21) 100-4100) 00% | 00 | 00 ara 4-04 | Monitor selection (terminal 23) 133 1 3 3 14-05 _| Gain Germinal 23) 000-250 | 001 | 030 | 050 114.06 | Bias Germinal 23) =10.0-4100] 0.1% | 00 | 00 114.07 | Analog ouput signal level selection ifofo 1501 | Station address 1 [oF [oF sMemogus| 45-02 _| Communication speed selection 7[3|3 a ‘Communication parity selection i 1 [ole ‘Slapping method ater communication | 9 oe ‘Communication eror detection selection) 0,1 fifa Motor] L1-01_| Motor protection selection on 1 H rrseson [1102 _| Motor protection ime constant 01-50 [Otminf Lo | 10 ‘Momentary power fos deecto G12 7 170 |e Miomentary power low aaetnmrtine 199-20 [oes] 10} 10 owerlos | 12-03 _| Min. baseblock time 00-50 [Oise] 03 | 05 Tags [E204 _| Voltage recovery time 00-50 [Oise] 03 | 03 12.05 | Undervoliage detection evel 150-210 | 1v | 190 | 190 12.06 _| KEB deceleration rate o0-1000 [01% [00 | 00 La-01 | Sill prevention selection durinE wT 19.1 9 ie 13-02 _| Stall prevention level during accel 0-200 1%_| 130 | 150 rorec. |S gg) E303 _| Sul prevention mit ding assel [0-100 | 18 | sd | 50 EME on Laos] Sal prevention selection during GSE T 9 5 ie Laos] ST prevention SeESTiCn ring FORTE] > tho to 13.06 _| Stall prevention level during running | 30-200 | 1% | 160 | 160 14-01 | Speed agree detection level 00-000 | 0.1nz| 00 | 00 regeny | LEO? _| Speed are detstion with 00-200 [oime| 20 | 20 \etestion | L403 | Speed agree detection level (7) 400-4000 [OHz | 00 | 00 TAO | Frequency detection widih (+/-) 00-200 [oiHz| 20 | 20 05 | Qaggg Wew Hagueny weteeNee To T | 00 | 00 Faultre- | L5-01_| Number of auto restart attempis 0-10 One| o | 0 sat | 75.q9 | Auto restart operation selection mn iam |KO 6-01 _| Torque detection selection | 4 1 foo lows. [6-02 | Torque detection level 1 0-300 1m | 150 | 150 ton [6.08 | Tongue detection time 1 10-100 [Oise] 01 | Onlover [Led | Torque detection selection Od 1 [oo BANE" Fass | Torque devction level? O30 1a _| 150) L606 | Torque detection ime 2 Oo-100 [Once] Oa E701 orwarl org it 0-300 1 | 200 oree: - MON |Toque [17-02 | Revers org ii 0-300 1 | 200 ft 7-03 | Forward regenerative torque limit 0-300 Vi 200 T7ot| Revere regenemtive wrque init 0-300 1 | 200) TLEOT | Protec election fr ineral DB resin [0.1 riefo {E802 | Overheatpre-alarm level son | ve | 9s | 95 Hardware | 18.03 | Operation selection after OH pre-alarm | 03 1 3 3 [povsston Input open-phase protection selection [0.1 1 0 0 ‘Oupatopen-phae proeetionekction [0.1 ce Selection of AVR function ou toto Monitor selection 3 rte f 6 — Monitor sekton ler powerap i ne rrr Freqny wit ofetoence sting nd oer [0=30909 | 1 | 0 | 0 ee Frequency units of constant seting Ol 1 0 oO Constant No. display selection on 1}olo LOCALREMOTE key enabledsable [0.1 rt1 fo oreraroR STOP hey ding conl cur terinal OP [0.4 rtoto ‘User constant inal value 012 rte] o Fonction KVA seletion 0-FF ee sane Fru feet ting maid oon | O1 pepo ad ‘Operation selection whe digital operators discomecies | 1 0 oO Cumulative operation time seving _|0-65835 | thour| - | Cumulative operation time selection [0.1 tio fe Tntalize mode selection 012 tte o 23Series SERVICE MANUAL [7] INVERTER DATA TABLE an Description | wee, | damage Rromark ‘AL-O1 | Constant access level | ~ bi06 | Realsequence input wise fo | - DC injection braking current Tso | 30 DC injection braking time at tart om | oso 12-08 | Magnetic fax compensation volume 180 Acceleration ime | woo | 50 Deceleration time | woo | 30 | Torque compensation gain vo | ta Torque compensation time conta 20 | 50 ‘Start vorquecompensation(Forvard eaten] 300 Sart true conan 20 Frequeney reference 2 0.00 | 300 | Inching speed 21-03 _ | Frequency eerene 3 [000 | 3000 | Blanket washing speed ‘ot _| Frequency reference 4 0.00 | 1800 | 3000 creep speed) 1-05 _ | Frequeney reference 5 000 | 200 | EPS speed 21-06 _ | Frequeney reference 6 000 | 050 | EPS spesd? «1-07 _ | Frequency reference 7 0.00 | 600 | Speed for sexing paper pos. 1-08 | Mid. ouput reauency volage Tio | 130 __| Torque for inching 1-10 _ | Min. ouput reuency volage 20__| 35 _| Torque forinching 1-05 | Mlianction input 5 ¢erminal) ° 5 1.03 | Biss (Germinal 13) 0.0 | 280 | 3000(inimun yd fle 13.05 _| Mul-fncton aalog npr cerminal 6) | 0 | _aF |