Chapter
2
:
Breakdown
Theory
Contents
Breakdown in gas
Breakdown in vacuum
Breakdown in solid
Breakdown in liquid
1
Introduc7on
Dielectric strength of insulating material depends on
the dielectric stress developed subjected to high
voltages.
Electric stress = Field intensity
E = -
Dielectric strength : maximum stress
which the material can withstand
2
Introduc7on
Dielectric breakdown strength depends on :
Pressure Temperature Surface
condition
Nature
Materials of
of applied
electrode voltage
Imperfections
Humidity in dielectric
material
3
Breakdown in Gas
4
Breakdown in Gas
5
The
process of converting an
atom or molecule into an ion*
by adding or removing charged
particles such as electrons.
*(total number electron is not equal to proton)
6
7
Electrode
surface
Pressure Heat
condition
Electrode Presence of
configuration particles in
initial flow
8
Breakdown in Gas
Maximum voltage during breakdown is
known as breakdown voltage
When the voltage is low, a small current
flows between electrodes and insulation
criteria do not change
When the voltage is high, a large current
flows causing sparks between electrodes
9
Breakdown in Gas
Electric discharge in gas consists of;
Non-sustaining discharge
Self-sustaining discharge
Breakdown in air is the change of non-sustaining discharge
to self-sustaining discharge
2 theories of gas breakdown;
Townsend Theory
Streamer Theory
10
Cell with gas pressure of
few Torr
11
d
I = I 0e
Io initial current at cathode
-
1st Townsend ionization
coefficient
d gap distance
12
At , I increase, V increase. How?
- Some of the electrons emitted by cathode
diffuse back into it and some lost to the
wall.
At , V increase, I saturate. How?
- All electrons emitted by cathode are
collected by anode
13
At , V increase, I
increase exponentially.
How?
- Additional productions
of electron by the
collision of positive
ions with the cathode
14
Primary ionization stage
If n0 is the number of electrons
emitted by cathode per second , then
number of electrons reaching anode
per second is given by :
d
n = n0e
[1]
Consequently, current inside
d the tube
is I d = I 0e
[2]
I = n e I 0; = n0 e
Remarks : d= gap length; = Towsends first ionization coefficient; d d ; I0 =
current generated by the u.v at the cathode. Note when I0 = 0; Id = 0 -------- not self sustained.
15
From [2];
Id d
=e
I0
Id
Plot of ln as a
I0
function of d will give
the value of
16
Secondary ionization stage
Townsed observed that with increasing voltage, current in
discharge tube will increase faster than predicted in eq.
[2] .
As the voltage increase, positive ions gain more energy.
With excess energy, positive ions will start liberating
electrons from electrode. Thats why current increase
faster than predicted in eq [2]. 17
Given n+ = number of electrons released from cathode (per second)
due to positive ion bombardment.
Then from eq.[1] the number of electrons reaching anode (per
second) , n is
d
n = (n + n )e
o +
[3]
After a while, number of electrons released by the positive ion is given
by { (
n+ = n n0 n+ )}
[4]
18
= Townsend secondary coefficient
Substituting [4] into [3];
n0ed
n=
(
1 ed 1 ) [5]
Since number of electron, n reflects current, I, hence
I 0ed
[6] I=
(
1 ed 1)
19
Eq. [6] shows that the discharge is non-self sustain. It will go to zero
when UV source to the cathode is removed, that is I0 = 0.
As the voltage continue to increase, the discharge will continue to burn
between electrodes even when UV radiation is removed (I0 = 0).
This is known as non-self sustained discharge to self sustained
discharge transformation.
20
The stage of electrical breakdown in small gap
happened when I , i.e.
( )
1 ed 1 = 0
Townsends breakdown criteria
21
Electron attachment removes free electrons and thus
gives gases very high dielectric strengths. The gases
in which electron attachment occurs are electro-
negative gases.
A gas which captures free electrons and forms negative
ions, so arresting the formation of electrical
discharges e.x SF6, CH3I, dry air, O2
22
Breakdown criteria (considering electron
attachment)
In air : 26 kV/cm (~ 30 kV / cm)
In SF6 : 88.4 kV/cm
23
Time lags of Spark breakdown
On the application of a voltage, a certain time
elapses before actual breakdown occurs even
though the applied voltage may be much more
than sufficient to cause breakdown.
24
Statistical time lag, ts
The average time required for an electron to appear in the gap
in order that breakdown may be initiated. It depends upon:
The amount of pre-ionization present in between the gap
Size of the gap
The amount of over voltage applied to the gap
Formative time lag, tf
The additional time lag required for the breakdown process to form.
increases with increase in gap length and field non-
uniformity,
decreases with increase in over voltage applied.
25
Arises due to the added effect of the space-
charge field of an avalanche and photo-electric
ionization in the gas volume.
Predicts the development of a spark discharge
directly from a single avalanche
As the electrons advance rapidly, the positive
ions are left behind in a relatively slow-moving
tail.
The field will be enhanced in front of the head.
Just behind the head the field between the
electrons and the positive ions is in the opposite
direction to the applied field and hence the
resultant field strength is less
26
Electron Avalanche
A
Photon
triggers
avalanche
B
Posi7ve
ions
strikes
cathode
and
starts
avalanche
C
Electron
avalanche
D
Avalanche
7p
reaches
anode
E
Photon
from
avalanche
produce
fee
electrons
F
Posi7ve
charges
close
to
anode
increase
the
electric
eld
28
G
Plasma
of
posi7ve
ions
and
electrons
forms
the
streamer
channel
H
Streamer
7p
I
Produc7on
of
free
electrons
by
photon
J
Streamer
propaga7ng
close
to
cathode
29
Depends on primary
Formative time avalanche reaching
lags of <= 50 ns a critical size
Local electric field high
enough to generate
streamers which
propagate towards
electrode
Breakdown criterion;
Er = 4/3rN
where N ion density
31
Given = pf1(E/p) and = f2(E/p). Under uniform field
distribution, E = V/d. According to Townsend breakdown
criteria;
(ed 1) = 1 Breakdown voltage is
an implicit function of
f2(V/dp)(epdf1(V/dp) -1)=1 pd
So the break down voltage can be written as
V= f(pd) ; p= pressure while d=gap distance
32
Under
constant
atm.
condi7on,
breakdown
voltage
for
uniform
eld
is
given
as:
V
=
A.d
+
Bd
where A= 24.4kV/cm and B = 6.29kV/cm1/2
Since
breakdown
voltage
can
vary
depending
on
the
gap
distance,
a
correc7on
factor
has
to
be
considered.
V=
A(d) + B(d)
Where = gas density correction factor
33
Consider fixed spacing, pressure
decrease from a point to the right of
the minimum
0.3kV
Density decreases and an
electron makes fewer collisions
10-2 [Link]
e n Each collision results in a loss of energy,
P a s c h
a lower electric stress suffices to impart to
s
m electrons the kinetic energy
minimu
in air
If
the
number
of
collisions
is
decreased,
breakdown
can
occur
only
if
the
chance
of
ionising
is
increased,
and
this
accounts
for
the
increase in voltage to the left of the
minimum
34
Valid for
temperatures below At very low
about 11000C above pressures, and at
that thermal very high pressures
ionization takes (compared with
place. atmospheric),
Paschen's Law fails
Typically the voltage
minimum is 300 V and
occurs at a product or
p.d of 5 torr mm, or at a
gap of about 0.06 mm
It was found in an experiment that a steady state current in a gas is 60 A
at 10 kV when the plane electrode separation is 0.5 cm. When the
separation is reduced to 0.25 cm and the field is the same, the current is
reduced to 6 A. Determine the Townsend first ionization coefficient .
36
In an experiment in a certain gas it was
found that the steady state current is 5.5 x
10-8 A at 8 kV at a distance of 0.4 cm
between the plane electrodes. Keeping the
field constant and reducing the distance to
0.1 cm results in a current of 5.5 x 10-9 A.
Calculate the Townsends primary
ionization coefficient .
37
The followings data are given for two
parallel plates while E is kept constant.
i) I = 1.2I0 when d = 0.5 cm
ii) I = 1.6I0 when d = 1.3 cm
iii) I = 2.3I0 when d = 2 cm
Find the values of and .
38
39
Measurement of breakdown voltage under a uniform field pressurized gas is shown in
Table Q2 below.
Assume that the Paschen curve for pd > 5 mm is represented by
Table Q2
Distance Pressure Temperature Breakdown
(cm) (mbar) (C) Voltage (kV)
2.3 500 21 35
2.9 800 25 60
1. Determine A and B
2. Calculate the breakdown voltage for the distance 1.5 cm at a pressure of 250 mbar and
temperature 25C
40
Breakdown in Liquid Dielectrics
Petroleum oils, synthetic hydrocarbons and
halogenated hydrocarbons and for very
high temperature applications silicone oils
and fluorinated hydrocarbons
Used for filling transformers, circuit
breakers and as impregnates in high
voltage cables and capacitors
Circuit breaker Transformer
Insulate the live parts and the Insulate the live parts of the transformer
grounded parts, quench the arc and the grounded parts, carrying out the
developed between the breaker heat from the transformer to the
contacts atmosphere thus providing cooling effect
41
Breakdown in Liquid Dielectrics
Mineral oils
Synthetic
(petroleum Biodegradable
ester
based)
Standard used : IEC 60256 (oxidation, viscosity etc.) and IEC60156 (for
determining breakdown voltage in insulating oils)
42
Breakdown in Liquid Dielectrics
43
Breakdown in Liquid Dielectrics
Liquid dielectric must free from moisture,
oxidation products and contamination
Factor that affect liquid dielectric
strength is the presence of fine water
droplets suspended in oil
The presence of 0.01% water in
transformer oil reduces its dielectric
strength by 20% of the dry oil value,
increase loss (tan ) and speed up ageing
process.
PRECAUTION !!!!!
Whenever these oils are used for providing electrical
insulation, these should be free from moisture, products
of oxidation and other contaminants.
44
Breakdown in Liquid Dielectrics
Among factors that will effect breakdown in liquid dielectrics is
temperature, pressure and viscosity.
Increased temperature causes an
increase in kinetic energy.
The higher kinetic energy causes more
motion in molecules which break
intermolecular bonds and escape from
solution.
45
Breakdown in Liquid Dielectrics
vIf the pressure is increased, the gas
molecules are "forced" into the solution.
vThe number of gas molecules is
decreased.
vThe number of gas molecules dissolved
in solution has increased
46
Breakdown in Liquid Dielectrics
Source
:
R.
Kurniato,
Z.
Nawawi,
M.
Nagao,
N.
Hozumi.
Breakdown
Strength
of
Biodegradable
Dielectric
Liquid:
The
eect
of
temperature
and
viscosity,
IEEE
Publica7on.
As
the
temperature
is
increased,
the
fat
contents
in
liquid
would
be
decrease.
The
decrease
of
fat
content
in
liquid
would
result
in
higher
breakdown
eld
strength
and
lower
viscosity.
47
Breakdown in Liquid Dielectrics
What happened?
The electrostatic forces on the bubble cause it to get elongated in the
direction of the electric field.
When sufficient electric field is applied, and at a critical length the gas
inside the bubble (which has a lower breakdown strength) breaks down.
This discharge causes decomposition of the liquid molecules and leads to
total breakdown.
48
Breakdown in Liquid Dielectrics
Due to liquid globules
Breakdown due to instability of the globule in the electric field. HOW???
The electrostatic forces cause the globule to elongate and take the shape of a
prolate spheroid. As the field is increased, the globule elongates so that the ratio
of the longer to the shorter diameter of the spheroid increases.
Electrodes
Liquid globules elongating as the
field increase. When it bridge the
electrodes, breakdown will occur.
Prolate spheroid
49
Breakdown in Liquid Dielectrics
When 2 >> 1 (generally when 2/1 > 20), and the field
exceeds a critical value, no stable shape exists, and the
globule keeps on elongating eventually causing bridging
of the electrodes, and breakdown of the gap.
50
Breakdown in Liquid Dielectrics
Due to solid particles
In commercial liquids, solid impurities
cannot be avoided and will be present as
fibers or as dispersed solid particles.
If permittivity of impurities 2 is larger than
permittivity of liquid dielectric 1 , then
A force would move the particle towards
the regions of stronger field and will line up
in the direction of the field
A stable chain of particles would be
produced, which at a critical length
may cause breakdown
51
Breakdown in Liquid Dielectrics
Purification Process
[Link] of dust Small dust particles can become charged and cause local
stresses which can initiate breakdown. Filtration can remove dust particles
greater in size than 1m. The strength of the liquid then increases and greater
stability is achieved.
2. Removal of dissolved gasses - to control the amount of oxygen and C02
through degassing and distillation
3. Removal of ionic impurities Ionic impurities in the liquid (ex. water) leads
to abnormal conductivity and heating of the liquid. Water can be removed by
drying agents, vacuum drying, and by freezing out in low temperature
distillation.
52
Breakdown in Solid Dielectrics
Organic matter paper,
wood, rubber SOLID DIELECTRICS
Non-organic matter
mica, glass, porcelain,
Perspex, PVC, epoxy
resins
The highest
Breakdown strength is breakdown strength
of the order of 10 MV/ under controlled
cm condition is known as
intrinsic strength of
the dielectric
53
Breakdown in Solid Dielectrics
Failure of solid
dielectrics below
Breakdown due
Chemical
intrinsic strength
to internal
deterioration discharge
Electrochemical Thermal
breakdown breakdown
Surface
Electromechanical breakdown
breakdown tracking and
erosion
54
Breakdown in Solid Dielectrics
When the voltage Vv across the void exceeds the critical voltage Vc, a discharge is
initiated and the voltage collapses.
The voltage across the void again builds up and the discharges recur
During the discharges, heat is dissipated in the voids which cause carbonization of
the surface of the voids and erosion of the material.
The gradual erosion of the material and consequent reduction in the thickness of
the insulating material eventually leads to breakdown.
Slow and may occur in a few days or may take a few years
55
Breakdown in Solid Dielectrics
When an electric field is applied to a dielectric between two electrodes, a
mechanical force will be exerted on the dielectric due to the force of attraction
between the surface charges.
This compression decreases the dielectric thickness , thus increasing the effective
stress
When the field is increased, the thickness of the material decreases
56
Breakdown in Solid Dielectrics
When the heat generated increases rapidly with temperature, at certain values of
electric field no stable state exists (stable state : the heat lost is equal to the heat
generated) - hence material breaks down thermally.
For the field E2, a stable temperature A exists.
For the field E1, the heat generated is always greater than the heat lost so that the
temperature would keep increasing until breakdown occurs.
57
Breakdown in Solid Dielectrics
Chemical changes due to consistent electric stress by
the reaction of air & gas
Reaction that occurs Oxidation, Hydrolysis, Chemical
Reaction
Can be reduce by carefully checking the material
58
Breakdown in Solid Dielectrics
In the presence of air or oxygen, especially ozone,
materials such as rubber and polyethylene undergo
oxidation giving rise to surface cracks, particularly if
stretched and exposed to light
When moisture or water vapour is present on the
surface of a solid dielectric, hydrolysis occurs and the
materials lose their electrical and mechanical
properties. Ex. Polyethylene film may lose its
mechanical strength in a few days if kept at 100 %
relative humidity.
Note: Hydrolysis is a process of splitting the
chemical bond of the insulating material by
addition of water
59
Breakdown in Solid Dielectrics
Progressive chemical degradation of
insulating materials. For instance
cellulose degrades much more rapidly
in the presence of traces of acidic
substances
60
Breakdown in Solid Dielectrics
Treeing & Tracking
Two effects of electric stress for a long period
of time;
Presence of conductive paths across surface
Effects of sparks due to leakage current that
flow through the paths that produce sparks
The spread of a spark channel during the
tracking process in the form of branches is
called treeing
61
