Scribd
Upload
5K views5 pages

Bolt Capacity Design Calculations

The document provides design data for bolt capacity including steel grades, bolt dimensions, plate thickness, material strengths, load values, and equations to calculate shear, tension, bearing, and punching capacities. It also includes a check of these capacities against applied loads and a combined shear and tension check. Design data tables from EN 1993-1-8:2005 are referenced throughout.

Uploaded by

Difa Liu
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
5K views5 pages

Bolt Capacity Design Calculations

The document provides design data for bolt capacity including steel grades, bolt dimensions, plate thickness, material strengths, load values, and equations to calculate shear, tension, bearing, and punching capacities. It also includes a check of these capacities against applied loads and a combined shear and tension check. Design data tables from EN 1993-1-8:2005 are referenced throughout.

Uploaded by

Difa Liu
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
  • Bolt Capacity Design: Presents the design data, calculations, and capacity checks related to bolt capacity following specific standards.
  • Fillet Weld Capacity: Tables displaying weld capacities according to different steel grades and throat sizes.
  • Compatibility Report: Report of compatibility issues documented for Excel file formats, highlighting potential data fidelity problems.
  • Version Information: Page listing the Excel version used for reference without substantial content.

BOLT CAPACITY DESIGN

The design data are as follows:


Steel grade S235
Bolt diameter d= 16 mm
Hole diameter d0 = 18 mm Bolt Grade 8.8
Gross bolt area A= 2.01 cm2
Net bolt area As = 1.57 cm2 No. of bolt 2
Plate thickness t= 12 mm
EN 1993-1-8:2005
Ultimate tensile strength of bolt fub = Err:502 N/mm2 Table 3.1
Ultimate tensile strength for steel fu = Err:502 N/mm2
Partial safety factors for joints g M2 = 1.25 EN 1993-1-8:2005
Table 2.1
Shear load Fv,Ed = 85.0 KN

Tension load Ft,Ed = 85.0 KN

Shear capacity EN 1993-1-8:2005


0 . 6 f ub A Table 3.4
F v,Rd=
γ M2
= Err:502 KN

Shear Capacity Err:502

Tension capacity EN 1993-1-8:2005


Table 3.4
0 . 9 f ub A s
F t,Rd=
γ M2
= Err:502 KN

Tension Capacity Err:502

Bearing capacity EN 1993-1-8:2005


Table 3.4
k 1 α b f u dt k1 = 2.50
F b,Rd= ab = Err:502
γ M2
= Err:502 KN

Bearing Capacity Err:502

Punching capacity EN 1993-1-8:2005


Table 3.4
0 .6 πd m tf u
B p,Rd =
γ M2
= Err:502 KN

Punching Capacity Err:502


BOLT CAPACITY DESIGN

Combined shear and tension EN 1993-1-8:2005


F v,Ed F t,Ed Table 3.4
+ ≤1
F v,Rd 1. 4 F t,Rd

Err:502 Err:502

Combined shear and tension Err:502

DESIGN CHECK

1 Shearing Resistance
2 Tension Resistance
3 Bearing Resistance
4 Punching Resistance
5 Combined Shear & Tension
Fillet weld capacity to EN 1993-1-8
Steel grades
Steel grade S235 S275 S355
Tensile strength fu, N/mm 2
360 430 510
Correlation factor bw 0.8 0.85 0.9
gM2 = 1.25

Fillet weld capacity Fw,Rd, kN/cm


Steel grade S235 S275 S355
Weld resistance fw,Rd, N/mm 2
208 234 262
4 8.31 9.35 10.47
6 12.47 14.02 15.70
8 16.63 18.69 20.94
Weld throat 12 24.94 28.04 31.41
a, mm 14 29.10 32.71 36.64
16 33.26 37.39 41.88
18 37.41 42.06 47.11
20 41.57 46.73 52.35
Compatibility Report for [Link]
Run on 15/09/2016 12:32

If the workbook is saved in an earlier file format or opened in an earlier version


of Microsoft Excel, the listed features will not be available.

Minor loss of fidelity # of occurrences

Some cells or styles in this workbook contain formatting that is not supported 30
by the selected file format. These formats will be converted to the closest
format available.
Version

Excel 97-2003

BOLT CAPACITY DESIGN The design data are as follows: Steel grade S235 Bolt diameter 16 mm Hole diameter 18 mm Bolt Grade 8.8
BOLT CAPACITY DESIGN Combined shear and tension EN 1993-1-8:2005 Table 3.4 Err:502 Err:502 Combined shear and tension Err:502
Fillet weld capacity to EN 1993-1-8 Steel grades Steel grade S235 S275 S355 Tensile strength 360 430 510 Correlation factor 0
Compatibility Report for aa.xls Run on 15/09/2016 12:32 Minor loss of fidelity # of occurrences 30 If the workbook is saved i
Version Excel 97-2003

You might also like