CCNA1 – Computer Networks Foundations Lab
Practice for Skills Exam
Topology
Assessment Objectives
Part 1: Develop the IPv4 Address Scheme (20 minutes)
Part 2: Configure the Physical Topology (5 minutes)
Part 3: Initialize and Reload Devices
Part 4: Configure Device IPv4 and Security Settings (20 minutes)
Part 5: Test and Verify IPv4 End-to-End Connectivity (10 minutes)
Part 6: Configure IPv6 Addressing on R1 (10 minutes)
Part 7: Test and Verify IPv6 End-to-End Connectivity (10 minutes)
Part 8: Cleanup - Initialize and Reload Router and Switch (5 minutes)
Phase 1: Subnetting
Part 1: Develop the IPv4 Addressing Scheme
Given an IP address and mask of ____________________________________ (address / mask),
design an IP addressing scheme that satisfies the following requirements. Network address/mask and
the number of hosts for Subnets A, B, C and D will be provided by your instructor. The 0 th subnet is
used.
Subnet Number of Hosts
Subnet A
Subnet B
Subnet C
Subnet D
Page 1 of 9
Subnet Number of Subnet Number of Network ID Prefix Subnet mask First Usable IP Last Usable IP Broadcast IP
Name Hosts Size Usable Hosts
Page 2 of 9
Host computers will use the first IP address in the subnet. The network router will use the LAST network host
address. The switch will use the second to the last network host address.
Write down the IP address information for each device:
Device IP address Subnet Mask Gateway
PC-A
R1-G0/0 N/A
R1-G0/1 N/A
S1 N/A
PC-B
Page 3 of 9
CCNA: Introduction to Networks SA Exam
Phase 2: Configuration and Testing Connectivity
Scenario
In this practice you will configure the devices in a small network. You must configure a router, switch and PCs
to support both IPv4 and IPv6 connectivity. You will test and document the network using common CLI
commands.
Required Resources
1 Router
1 Switch
2 PCs
Console cable
Ethernet cables
IPv4 addressing Scheme:
Device IP address Subnet Mask Gateway
PC-A
R1-G0/0 N/A
R1-G0/1 N/A
S1 N/A
PC-B
Page 4 of 9
CCNA: Introduction to Networks SA Exam
Part 2: Configure the Physical Topology
Step 1: Physically connect lab devices
Cable the network devices as shown in the figure. If not already enabled, turn power on to all devices.
Step 2: Visually inspect network connections
Step 3: After cabling the network devices, take a moment to verify the connections.
Correct Cabling
LAN cable between PC-A and R1 G0/0
LAN cable between S1 and R1 G0/1
LAN cable between S1 and PC-B
Console cable between R1 and any of the hosts
Devices turned on
Part 3: Initialize and Reload Devices
Step 1: Initialize and reload router and switch.
Erase the startup configurations and VLANs from the router and switch and reload the devices.
Before proceeding, have your instructor verify device initializations.
Part 4: Configure Device IPv4 and Security Settings
Step 1: Configure host computers.
After configuring each host computer, record the host network settings with the ipconfig /all command.
PC-A Network Configuration
Description
Physical Address
IP Address
Subnet Mask
Default Gateway
Page 5 of 9
CCNA: Introduction to Networks SA Exam
PC-B Network Configuration
Description
Physical Address
IP Address
Subnet Mask
Default Gateway
Step 2: Configure R1.
Configuration tasks for R1 include the following:
Task Specification
Disable DNS lookup
Router name R1
Encrypted privileged exec password cisco
Console access password cisco
Telnet access password cisco
Encrypt the clear text passwords
MOTD Banner
Set the description
Interface G0/0 Set the Layer 3 IPv4 address
Activate Interface
Set the description
Interface G0/1 Set the Layer 3 IPv4 address
Activate Interface
Step 3: Configure S1.
Configuration tasks for R1 include the following:
Task Specification
Switch name S1
Configure Management Interface (SVI) Set the Layer 3 IPv4 address
Encrypted privileged exec password cisco
Console access password cisco
Telnet access password cisco
Page 6 of 9
CCNA: Introduction to Networks SA Exam
Part 5: Test and Verify IPv4 End-to-End Connectivity
Step 1: Verify network connectivity.
Use the ping command to test connectivity between all network devices.
Note: If pings to host computers fail, temporarily disable the computer firewall and retest. To disable a
Windows 7 firewall, select Start > Control Panel > System and Security > Windows Firewall > Turn Windows
Firewall on or off, select Turn off Windows Firewall, and click OK.
Use the following table to methodically verify connectivity with each network device. Take corrective action to
establish connectivity if a test fails:
From To IP Address Ping Results
PC-A R1, G0/0
PC-A R1, G0/1
PC-A S1 VLAN 1
PC-A PC-B
PC-B R1, G0/1
PC-B R1, G0/0
PC-B S1 VLAN 1
In addition to the ping command, what other command is useful in displaying network delay and breaks in the
path to the destination?
_______________________________________________________________________________________
Part 6: Configure IPv6 Addressing on R1
Given an IPv6 network address of [Link]/64, configure IPv6 addresses for the Gigabit interfaces
on R1. Use FE80::1 as the link-local address on both interfaces.
Step 1: Configure R1.
Configuration tasks for R1 include the following:
Task Specification
Assign the IPv6 unicast address
Configure G0/0 to use the first address in subnet A.
Assign the IPv6 link-local address
Assign the IPv6 unicast address
Configure G0/1 to use the first address in subnet B.
Assign the IPv6 link-local address
Enable IPv6 unicast routing.
Page 7 of 9
CCNA: Introduction to Networks SA Exam
Part 7: Test and Verify IPv6 End-to-End Connectivity
Step 1: Obtain the IPv6 address assigned to host PCs.
PC-A IPv6 Network Configuration
Description
Physical Address
IPv6 Address
Default Gateway
PC-B IPv6 Network Configuration
Description
Physical Address
IPv6 Address
IPv6 Default Gateway
Step 2: Use the ping command to verify network connectivity.
IPv6 network connectivity can be verified with the ping command. Use the following table to methodically
verify connectivity with each network device. Take corrective action to establish connectivity if a test fails:
From To IP Address Ping Results
PC-A R1, G0/0
PC-A R1, G0/1
PC-A PC-B
PC-B R1, G0/1
PC-B R1, G0/0
Part 8: Cleanup - Initialize and reload router and switch
Unless directed otherwise by the instructor, restore host computer network connectivity, and then turn off
power to the host computers.
Page 8 of 9
CCNA: Introduction to Networks SA Exam
Before turning off power to the router and switch, erase the startup configurations and VLANs from
the router and switch and reload the devices.
Task IOS Command
Erase the startup-config file on the
Router.
Reload the Router.
Erase the startup-config file on the
Switch.
Delete the [Link] file on the
Switch
Reload the Switch.
Disconnect and neatly put away all LAN cables that were used.
Page 9 of 9
