11 Buzzer/Speaker
The buzzer/speaker pictured in Figure 11.1 (also 2. Select a transistor to drive the coil from a digital
called a magnetic transducer) generates tones over output,
much of the audible frequency spectrum. The 3. Protect the transistor from back-emf voltage
speaker coil is designed for on-off operation (5 volts spikes when the transistor switches the coil
at 80 mA when on), therefore cycling the speaker current on and off, and
with a square wave created from a digital output is 4. Design the interface circuit to work with digital
the most straightforward way to operate the speaker. outputs that include either pull-up or pull-down
A transistor-based interface circuit is required to resistors.
drive the coil.
11.1 Component Demonstration
Follow these steps to demonstrate correct operation
of the buzzer/speaker.
Select these parts from the NI myRIO Starter Kit:
• Buzzer/speaker, Soberton GT-0950RP3,
http://www.soberton.com/product/gt-0950rp3
• 1N3064 small-signal diode, http://www.
fairchildsemi.com/ds/1N/1N3064.pdf
• 2N3904 npn transistor, http://www.fairchildsemi.
com/ds/MM/MMBT3904.pdf
• Resistor, 1.0 kΩ
Figure 11.1: NI myRIO Starter Kit buzzer/speaker. • Breadboard
• Jumper wires, M-F (3×)
Learning Objectives: After completing the activities Build the interface circuit: Refer to the schematic
in this chapter you will be able to: diagram and recommended breadboard layout
1. Describe the buzzer/speaker principle of shown in Figure 11.2 on page 45. Note that
operation based on an electromagnetic coil that the two buzzer/speaker terminals do not sit on
vibrates a small diaphragm, tenth-inch centers, however, they fit just fine in two
44 11. BUZZER/SPEAKER
diagonally-adjacent breadboard holes. The interface causes all of the digital I/O pins to revert to input
circuit requires three connections to NI myRIO MXP mode.
Connector B (see Figure A.1 on page 233):
1. 5-volt power supply → B/+5V (pin 1) Troubleshooting tips: Not hearing the expected
2. Ground → B/GND (pin 6) results? Confirm the following points:
3. Buzzer/speaker control → B/PWM0 (pin 27) • Glowing power indicator LED on NI myRIO,
• Black Run button on the toolbar signifying that
the VI is in run mode,
Run the demonstration VI: • Correct transistor orientation — the transistor has
• Download http://www.ni.com/academic/myrio/ a rounded shape on one side, and
project-guide-vis.zip if you have not done • Correct diode orientation — when the diode is
so previously and unpack the contents to a backwards the buzzer/speaker coil will never
convenient location, reach the voltage level necessary to turn on.
• Open the project Buzzer-Speaker
demo.lvproj contained in the subfolder
Buzzer-Speaker demo, 11.2 Interface Theory
• Expand the hierarchy button (a plus sign) for
the myRIO item and then open Main.vi by Interface circuit: The buzzer/speaker contains an
double-clicking, electromagnetic coil that vibrates a small diaphragm.
• Confirm that NI myRIO is connected to your The coil current is approximately 80 mA, well
computer, and beyond the current drive limits of the NI myRIO
• Run the VI either by clicking the Run button on digital output. The interface circuit uses an NPN
the toolbar or by pressing Ctrl+R. transistor as a switch to turn the coil current on and
off and a diode to protect the transistor from large
Expect to see a “Deployment Process” window back-emf voltage when the transistor abruptly shuts
showing how the project compiles and deploys off the coil current.
(downloads) to NI myRIO before the VI starts Study the video Buzzer/speaker Characteristics
running. (youtu.be/8IbTWH9MpV0, 5:14) to learn more
NOTE: You may wish to select the “Close on about the buzzer/speaker characteristics and
successful completion” option to make the VI start interface circuit design principles including: sizing
automatically. the transistor for relay coil current, importance of
the diode to deal with back-emf voltage spiking,
Expected results: Your buzzer/speaker should be and circuit topologies for DIOs with internal pull-up
making a low-frequency tone at 40 Hz. Move the resistors (MXP connector) and internal pull-down
front-panel control frequency [Hz] to increase the resistors (MSP connector).
frequency. At what frequency is the sound output
level the highest? What is the highest frequency that LabVIEW programming: Study the video PWM
you can hear? Try blocking the port (rectangular Express VI (youtu.be/mVN9jfwXleI, 2:41) to
hole) – how does this affect the sound at different learn how to use the PWM Express VI (PWM =
frequencies? pulse-width modulation) to create a squarewave
Click the Stop button or press the escape key to output on B/PWM0 (pin 27) in the frequency range
stop the VI and to reset NI myRIO; a myRIO reset 40 Hz to 40 kHz with adjustable pulse width.
11. BUZZER/SPEAKER 45
Figure 11.2: Demonstration circuit for buzzer/speaker: schematic diagram, recommended breadboard
layout, and connection to NI myRIO MXP Connector B.
46 11. BUZZER/SPEAKER
11.3 Basic Modifications
Study the video Buzzer/speaker Demo Walk-
Through (youtu.be/kW4v16GuAFE, 2:06) to learn
the design principles of Buzzer-Speaker demo,
and then try making these modifications to the
block diagram of Main.vi:
1. Add a front-panel control to adjust the waveform
pulse width (called duty cycle) between 0 % and
100 %. How does a narrow pulse (low duty cycle)
affect the tone quality at various frequencies?
2. Create a two-tone alarm signal with a Boolean
front-panel control as an enable. Review Dis-
crete LED demo.lvproj from Section 2.3
on page 7 to learn how to make a two-state
oscillator.
11.4 Integrated Project Ideas
Now that you know how to use the buzzer/speaker
consider integrating it with other devices to create
a complete system, for example:
• Music Maker (56)
• NTP Clock (43)
11.5 For More Information
• Products by Soberton Inc. ∼ Discover related
products to the buzzer/speaker in the NI myRIO
Starter Kit:
http://www.soberton.com/products
