Yudian (H.K.) Automation Technology Co. Ltd.

Website: [Link] [Link]

Email: sales@[Link]
Tel: +852-2770 8785 Fax: +852-2770 8796

AI-702M/704M/706M

HIGH PERFORMANCE INTELLIGENT

MULTI-CHANNEL INDICATORS
Operation Instruction Version 7.7
(Ideal for measurement, indication, alarm, calculation and retransmission of
temperature, pressure, flow, level, humidity etc.)
 Yudian (H.K.) Automation Technology Co. Ltd.
Website: [Link] [Link]
Email: sales@[Link]
Tel: +852-2770 8785 Fax: +852-2770 8796

SUMMARY
AI-702M, AI-704M and AI-706M multi-channel indicators provide 1-2, 1-4, 1-6 channels of
independent process indications, and are ideal for the measurement, indication, alarm,
calculation and retransmission of temperature, pressure, flow, level and humidity etc.

Features:
★ Programmable and modular inputs. Multiple input types of thermocouples and RTDs,
voltage/current inputs and two-wire transmitters are field- selectable.
★ Each channel can have independent input specification. All channels are equipped with
digital adjustment and filtering functions and each channel have individual digital
adjustment and filtering parameters.
★ Customized channel number for easy reading when measuring more than 6 channels,
e.g. instrument 1 shows CH1 ~ CH6 while instrument 2 shows CH7 ~ CH12.
★ High performance hardware design, greatly reduce the temperature drift and the
interference between channels, thus multi-channel measurement accuracy is 0.2% full
scale, the same as that of single channel.
★ Provide high accuracy compensation function such as ice-point compensation, copper
resistance compensation and thermostat compensation to thermocouple inputs.
★ Build-in accurate internal calculation functions including square root extraction,
summation, subtraction and multiplication.
★ Support up to 2 isolated retransmission output. Any input channel can be retransmitted
to OUTP port or all channels are cyclically retransmitted.
★ Provide manual/auto pilot display, with 2 pilot speed selectable.
★ Support up to 7 on-off signal inputs/outputs which can work as alarm output or on-off
signal I/O for host computer.
★ Each input channel has independent low/high limit alarm which can be assigned to any
alarm output.
★ Advanced communication function. Provide high accuracy and stability multi-channel
analog data sampling function to host computer. The host computer can also input up
to 7 channel on-off signal or execute on-off operation via the indicator.
★ Up to12 customized field parameters.
★ Multiple dimensions are selectable. 100~240VAC universal power supply.
★ Achieved ISO9001 and CE certificates, comply with EMC standard, high reliability and
stability. The power and I/O terminals have passed the anti-interference test of
4KV/5KHz burst of pulses.
 Yudian (H.K.) Automation Technology Co. Ltd.
Website: [Link] [Link]
Email: sales@[Link]
Tel: +852-2770 8785 Fax: +852-2770 8796
ORDERING CODE

Designed with modular principle, AI-702M/704M/706M can be equipped with 6 modules on 6

sockets: M1, M2(MIO), M3(OUTP), ALM, AUX, and COMM. M1, M2 and M3 can be
equipped with various input modules, each of which has 1or 2 analog input channels. ALM,
AUX and M3(OUTP) can be equipped with relay output module, each of which has 1 or 2
alarm output channels. If necessary, M2 can also be installed with a single relay output
module and work as alarm output. COMM can only be equipped with RS485 interface for
communication with computer. M2 and M3 can be equipped with either analog input module
for measurement or relay output modules for alarm. All inputs and outputs are
programmable.

The ordering code of AI-702M/704M/706M is made up of 9 parts, for example:

AI-706M - A - J1 - J2 - J5 - L5 - L5 - S - 24VDC
① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨

Above code symbols a AI-706M instrument with: front panel dimension 96×96mm, 2
thermocouple inputs, 2 two-wire RTD inputs, 2 current inputs, 4 alarm relay outputs, RS485
communication interface and the supply power is 24VDC. The explanation for each code is
below:

① Shows the model of the indicator

AI-702M, AI-704M, AI-706M respectively indicate 2, 4, 6 channels indicator.

② Shows dimension.
The depth of the instrument is about 13.5mm(foreside) + 100mm(rearward).
Front Panel Cut-out
Model Remarks
(width x height) (width x height)
A 96x96mm 92x92mm
B 160X80mm 152x76mm
C 80x160mm 76x152mm
E 48x96mm 45x92mm
E5 is no panel design. It is installed on DIN
trail and programmed by connecting to
E5 96x48mm
external display or computer (S/S5 module
required).
F 96x48mm 92x45mm

③~⑧ Symbols the module type installed on sockets ( M1、M2、M3、AL1、AL2、COMM):

( “√” means the module can be installed on the according socket)
M2 M3
Module M1 ALM AUX COMM
(MIO) (OUTP)
N: No module installed √ √ √ √ √ √
1 channel three-wire RTD,
J0: √ √ √
thermocouple or mV voltage input
2 channel two-wire thermocouple or
J1: √ √ √
mV voltage inputs
J2: 2 channel two-wire RTD inputs √ √ √
 Yudian (H.K.) Automation Technology Co. Ltd.
Website: [Link] [Link]
Email: sales@[Link]
Tel: +852-2770 8785 Fax: +852-2770 8796
2 channel voltage inputs of 0-1V, 0-3V,
J3: √ √ √
0-5V or 1-5V etc.
2 channel current inputs of 0-12mA,
J4: √ √ √
4-20mA, 0-20mA etc.
2 channel two-wire transmitter
J5: √ √ √
provided 24VDC power supply.
2 channel on-off signal inputs, dry
I5: √ √ √
contact
L1: Single relay contact (NO+NC) output.
√ √ √
(30VDC/2A, 264VAC/2A)
L2: Single relay contact (NO+NC) output.
√ √ √
(30VDC/1A, 264VAC/1A)
L4: Single relay contact (NO+NC) output.
√ √ √
(30VDC/2A, 264VAC/2A)
L5: Dual relay contact (NO) outputs.
√ √ √
(30VDC/2A, 264VAC/2A)
1 channel thyristor normal open
output.
W1:
(“Burnt proof” technology, able to stand √ √ √
0.3A continuous current or 1A transient
current)
G: 1 SSR voltage output (12VDC/30mA) √ √ √
G5: 2 SSR voltage outputs (12VDC/30mA) √ √ √
S: Photoelectric isolated RS485 interface √
Photoelectric isolated RS485 interface
S4: √
with isolated power supply.
Photoelectric isolated linear current
X3: √ √
output
Photoelectric isolated linear current
X5: output with its own isolated power √ √
supply.
Photoelectric isolated 5VDC/50mA
V5: √ √
power supply for transmitter.
Photoelectric isolated 10VDC/50mA
V10: √ √
power supply for transmitter.
Photoelectric isolated 12VDC/50mA
V12: √ √
power supply for transmitter.
Photoelectric isolated 24VDC/50mA
V24: √ √
power supply for transmitter.

⑨ Shows power supply: Null indicates 100～240VAC power supply, and “24VDC” indicates
20～32VDC/AC power.
 Yudian (H.K.) Automation Technology Co. Ltd.
Website: [Link] [Link]
Email: sales@[Link]
Tel: +852-2770 8785 Fax: +852-2770 8796
TECHNICAL SPECIFICATION

 Input:

Thermocouples: (with J1 module)

K, S, R, E, J, T, B, N and WRe5-WRe26

Two-wire RTDs: (with J2 module that supports 2 inputs)

PT100, Cu50, 0~80 ohm, 0~400 ohm

Three-wire RTDs: (with J0 module that supports 1 inputs)

PT100, Cu50, 0~80 ohm, 0~400 ohm

Linear mV voltages: (with J1 module)

0~20mV, 0~60mV, 0~100mV, 0~1V

Linear voltage: (with J3 module)

0~1V, 0~3V, 0~5V, 1~5V etc.

Linear current: (with J4 module)

0~12mA, 0~20mA, 4~20mA etc.

Square root extraction calculation input: (with J3 voltage or J4 current input module)
1~5V, 4~20mA etc.

Two-wire transmitter inputs: (with J5 module that provides 24VDC power supply)
Connect to 4~20mA two wires transmitter

 Maximum lead wire resistance for RTD input:

2-wire type RTDs:

2 ohm for Pt100 or 0~400 ohm input ;1 ohm for Cu50 and 0-200 ohm input；

3-wire type RTDs:

5 ohm

 Measurement range：

K(0~1300℃ ), S(0~1700℃ ), R(0~1700℃ ), T(-200~+350℃ ), E(0~1000℃ ),

J(0~1200℃ ), B(0~1800℃ ), N(0~1300℃ ), WRe5-WRe26(0~2300℃ ),
Pt100(-200~+800℃ ), Cu50(-50~+150℃ )
Linear input：-1999~+9999 set by user

 Measurement accuracy:

±0.2%FS±1digit / ±0.3%FS±1digit (only for Cu50)

Note 1: For thermocouple inputs with internal cold junction compensation, 1℃ CJC error
should be taken into consideration. For those with Cu resistor, ice point or thermostat bath
compensation, the accuracy is as above.
Note 2: Accuracy is not guaranteed between 0 and 600℃ for type B thermocouple input.
 Yudian (H.K.) Automation Technology Co. Ltd.
Website: [Link] [Link]
Email: sales@[Link] Tel: +852-2770
8785 Fax: +852-2770 8796
● Temperature drift :
≤0.01%FS/℃ (typical 50ppm/℃ )

 Electromagnetic compatibility:
IEC61000-4-4, ±4KV/5KHz; IEC61000-4-5, 4KV

 Isolation withstanding voltage:

Between power, relay contact and signal terminals ≥ 2300VDC;
Between isolated eletroweak signal terminals ≥ 600VDC

 Response time：
≤1.5 seconds（if digital filter parameter is set as 0 or 1）

 Automatic pilot time interval：

Approx. 1.2s or 2s configurable

 Alarm function：
High and low alarm, configurable separately for each channel

 Alarm output:
Relay contact output（NO or NC） ：250VAC/1A or 30VDC/1A
No contact discrete output（NO or NC）：250VAC/0.3A(transient current 1A)

 Power supply:
100~240VAC/50Hz, 24VDC

 Power consumption：≤6W

 Work ambience：Temperature -10~+60℃ , Humidity ≤ 90%RH

 Yudian (H.K.) Automation Technology Co. Ltd.
Website: [Link] [Link]
Email: sales@[Link] Tel: +852-2770
8785 Fax: +852-2770 8796
TERMINAL LAYOUT AND WIRING
IN3
IN3
1 1 1111
COM COM
COM COM
100-240VAC~
100-240VAC~

2 2 OP2/IN6 + +N/ON/ON/CN/C 1212

OP2/IN6

OP1/IN5 + +N/ON/ON/ON/O
OP1/IN5
3 3 1313
+ +A A OUTP/M3
OUTP/M3
B B IN2
IN2
4 4 1414
COMM
COMM COM
COM
This graph is for upright
5 5 + +N/CN/C 1515
IN4IN4 instruments with
+ +N/ON/ON/ON/OAL1AL1 dimension A, C, E.
+ +N/ON/O
IN3IN3
6 6 + +N/CN/CN/ON/OAL2AL2 1616
M2/MIO
M2/MIO 注：本图为 A、C、E 型竖
COM COM
COM COM IN1
IN1
式面板的式仪表接线图。
7 7 1717
ALM
ALM
For instruments with
8 8 + +1818
IN2IN2 dimension B, F , just
+ +N/ON/ON/ON/OAU1AU1 clockwise rotate the
AU2
AU2 ++
IN1IN1
graph for 90 degree,
本图顺时针旋转 90 度后
9 9 + +N/CN/CN/ON/O 1919
M1M1 and
为 B、 the terminal
F 型横式面板仪表
COM COM
COM COM numbers keep
的接线图，端子编号不
1010 CJC
CJC 2020 unchanged.
变。
AUX
AUX

Thermocouple wiring:
When wiring a thermocouple input, the compensation wire should be qualified and directly connect to the
corresponding terminals in correct direction. When M1 module is installed in J1 socket, a Cu50 resistor can
be connected between terminal 17 and 20 to compensate the cold junction; short terminal 17 and 20 to have
ice-point compensation.

Two-wire RTD wiring:

RTD can select two-wire or three-wire method by B of “AF” parameter. Two-wire method accepts input two
channel signals in one module, but user has to measure and calculate the resistance of the wire. To apply
two-wire method, J2 module should be installed and resistance of each wire should be less than 2ohm.

AI-702M/704M/706M can measure the lead wire resistance of two-wire method and save it to parameter “Sc”.
However, the lead wire resistance changes as the temperature changes. If the lead wires has the same
ambient temperature as that of the instrument and no other resistor series connects to the lead wire, the
indicators can compensate the resistance change by measuring the ambient temperature (compensation
coefficient is 0.004/℃ ); otherwise, two-wire method is not recommended.

Three-wire RTD wiring:

Three-wire method is a traditional wiring method requiring that the resistance of the three wires be equal. One
“J0” module supports 1 three-wire RTD. Three-wire method provides higher measurement accuracy.

Maximum 3 channel of three-wire RTD is accepted. The channel number automatically shifts forward,
affecting the parameter application. E.g. J0 module is installed in M1 and M2 slot for two three-wire RTD. J2
module is installed in M3. This implies the instrument accept four channels (Parameter: Cn=4, AF.B=1).
There is no IN5 and IN6. Three-wired RTD is recommended to install in prior slot to avoid confusion.

Two-wire retransmission input:

AI-702M/704M/706M internally provide 24VDC power, maximum 90mA, for up to 4 two-wire transmitters. J5
module can directly be connected to two-wire transmitter. Each instrument is recommended to install not
more than two J5 or V24 modules, otherwise the instrument may be failed to power on because of overload.
Certain measurement error occurs due to they are commonly grounded as well. If more retransmission is
 Yudian (H.K.) Automation Technology Co. Ltd.
Website: [Link] [Link]
Email: sales@[Link] Tel: +852-2770
8785 Fax: +852-2770 8796
required, it should be equipped with extra 24V power supply and J4 current module.

FRONT PANEL AND OPERATIONS

○
1 Upper display window PV
○
2 Lower display window ①
○
3 Set key
○
4 Data shift key (also for switching between
manual/auto cyclic display) SV
○
5 Data decrease key (also for switch to ②
display the previous channel)
○
6 Data increase key (also for switch to MAN PRG MIO COM OP1 OP2 AL1 AL2 AU1 AU2
⑦
⑥
display the next channel)
○
5 10 LED indication lights.
③ ⑥
“MAN” on: Means manual circular display,
A/M RUN/HOLD STOP
“MAN” off: Means auto circular display. ④ ⑥
⑤
MIO, OP1, OP2, AL1, AL2, AU1, AU2 AI
indicate the input/output action of the
corresponding module. “COM” on: communicating with the host computer.
BASIC OPERATION DESCRIPTION

1. Switch display channel:

Press to display next channel, and press to display previous channel. Press can switch
between auto cyclic display and manual display.

2. Parameter setting:

When the parameter lock is unlocked, press and hold for about 2 seconds until parameter is
displayed. At this moment, press in short; all parameters will be displayed one by one. When the
parameters are set and the parameter lock is locked, press can access Field Parameter Table.
The value of a parameter can be modified by , or . Press to go to next parameter.
Press and hold can return to the previous parameter. Press + can exit parameter
setting status.

3. Alarm display:

The lower display window shows channel number. If high or low alarm occurs, the first digit from the left
of lower display window will show “H” or “L”, and flickers, and if over range occurs (for example, wire
broken for thermocouple input), the upper display window will show high or low limit valve, and the lower
display window flickers.
If only 2 input channels configured, then the upper and lower display window will show
the input values of channel 1 and 2 respectively. When over range occurs, the corresponding display
window will flickers.

Lead wire resistance compensation for 2-wire RTD input:

Offset value (parameter “Sc”) need to be set to counteract lead wire resistance for 2-wire type RTD like
Pt100 or Cu50. This offset value can be set automatically by the following procedures:
1. Short connect 2 wiring terminals on the RTD sensor side
2. Set parameter “Loc” to 808, and then press until “A” appears on the first digit of lower display
window.
 Yudian (H.K.) Automation Technology Co. Ltd.
Website: [Link] [Link]
Email: sales@[Link] Tel: +852-2770
8785 Fax: +852-2770 8796
3. Wait until “A” disappears, and then removes the short wire, and set “Loc” to 0 or 1.
4. Now, the instrument comes back to normal measurement display mode, and the setting of
parameter “Sc” is finished.

The unit of Sc is 1/20000 of the scale of the corresponding RTD. At 0℃ , the total resistance of the two lead
wire of Pt100 or 0~400ohm should be less than 4ohm, and that of Cu50 should be less than 2ohm.
Otherwise, wire resistant compensation will not function. The smaller the resistance of the lead wire, can
provide more accurate measurement.

4. DIN rail mounted type

DIN mounted type (dimension E5) has no display window. It can input analog signals or input/output on-off
signals for host computer or PLC, and it can also work as a two-channel programmable re-transmitter.
E5 dimension instrument has one LED indication light. When the instrument is communicating with the host
computer, the light flashes with light on time different to light off time. When the instrument hasn’t received
signal from the host computer for 6 seconds, the indication light should flash with the same light on time and
light off time.

It means:
 That the on-off period is as long as 1.6 second means no communication and no alarm (it can be treated
as normal);
 The light flashing with period 0.6 second means no communication and general error occurs.
 The light quickly flashing with period 0.3 second means no communication and severe error such as
input over range occurs.
 The light keeping off means the instrument power off or damaged; the light keep on (longer than 8
seconds) means the instrument power on but damaged.

The parameters of E5 dimension instrument can be set by connecting external display to the 1394 socket.
Note: The 1394 socket of the instrument only supports Yudian external display.

The instrument can connect PC or PLC to monitoring or capture the data. We can provide the FREE protocol
for user or order our monitoring software-AIDCS. Please contact Yudian Sales Dept. for more detail.

5. Dry Bulb, Wet Bulb Humidity Measurement

By connecting 2 units of three-wire PT100 input, is can become the dry bulb, wet bulb humidity measurement.
1. Install J0 (RTD input module) in both M1 and M2 slot. Set Sn1=22, Sn2=42.
2. Atmospheric pressure and wind speed defined by parameter “Po” and “SPEd”
3. Initialize measurement by wrapping dry bulb with wet muslin, giving same condition with wet bulb
4. Once reading is stable, adjust parameter Sc2 to offset reading to 100%,
5. Remove wet muslin after the adjustment.
6. Recommended to set parameter (dIP1=1, dIP2=0) to have more stable reading with resolution 0.1℃
and 1%RH.
 Yudian (H.K.) Automation Technology Co. Ltd.
Website: [Link] [Link]
Email: sales@[Link] Tel: +852-2770
8785 Fax: +852-2770 8796
PARAMETER DESCRIPTION
*x refers to channel number, can be 1~2, 1~4, 1~6 for AI-702M, 704M and 706M respectively.

Parameter Name Remarks Setting range

x channel high alarm on when PVx (the present value of x
channel)>[Link];
[Link] High limit alarm
Alarm releases when PVx<[Link] - dFx. -1999~+9999 ℃ or
Set [Link] maximum value will disable function defined unit
x channel low alarm on when PVx<[Link];
[Link] Low limit alarm Alarm releases when PVx>[Link] + dfx.
Set [Link] minimum value will disable function
dF is set to avoid high frequent alarm on/off actions 0~999.9℃ or
dFx Dead band
caused by process input fluctuation. 0~9999 units
Sn Input spec. Sn Input spec.
0 K 1 S
2 R 3 T
4 E 5 J
6 B 7 N
8 WRe3-WRe25 9 WRe5-WRe26
Extended
10 11~18 Spare
input spec.
19 BA2 (JPt100) 20 Cu50
Pt100
21 Pt100 22
(-100.00~+300.00) ℃
23~24 Spare 25 0~75mV
26 0~80ohm 27 0~400ohm
0~100mV, 0~5V (J3);
28 0~20mV 29
0~20mA (J4)
30 0~60mV 31 0~1V
Input
Snx 0.2~1V ; 0 ~ 39
specification
two-wire 1~5V voltage (J3)
32 33
re-transmitter 4~20mA current (J4)
(J5)
Extraction for range:
Extraction for
38 39 1~5V (J3)
range: 0.2~1V
4~20mA (J4)

Note: Input spec. should be compatible with input module.

For those spec. unknown, use J1 for thermocouple and
mV inputs, J2 for two-wire RTD, and J0 for three-wire
RTD.
Multiplication: set Sn3=40, PV3=PV1 x PV2 (PV refer to
input value)
Summation: set Sn3, Sn4, or Sn5 =41, its input is the sum
of the inputs of previous channels, e.g. when Sn5=41,
PV5=PV1+PV2+PV3+PV4.
Subtraction: set Sn3=42, PV3=PV2-PV1
 Yudian (H.K.) Automation Technology Co. Ltd.
Website: [Link] [Link]
Email: sales@[Link] Tel: +852-2770
8785 Fax: +852-2770 8796

dIPx is set to select display resolution for channel x.

Linear input: display resolution of dIP=0,1,2,3 are 0, 0.0,
0.00 and 0.000
Decimal point
dIPx Thermocouple or RTD inputs: when dIP=0, the display 0~3
position
resolution is 1℃ ; when dIP=1, the resolution is 0.1℃ .
Note: dIP only affects the display, and has no effect on
internal data. Resolution becomes 1℃ when over 1000℃ .

dIL and dLH define the corresponding scale range of linear

inputs such as mV, 0~5V, 1~5V, 0~10mA, 4~20mA.
dILx Scale low limit When the temperature input is retransmitted, dIL/dIH also
defined the low/high limit of temperature.
For example, a pressure transmitter transfers the pressure
-9990~+30000
to standard 1~5V signal and sends to input channel 1.
units or 0.1℃
The input of 1V indicates the pressure=0MPa, and 5V
indicates the pressure=1MPa, and expected display
dIHx Scale high limit resolution is 0.001MPa. Then the parameters should be
set as below:
Sn1=33, dIP1=3, dIL1=0.000, dIH1=1.000

For thermocouple or three-wire RTD inputs, the units of Sc

is 0.1℃ . For example, when Sc=-100, the actual
offset=-10℃ , then the measured temperature will be 10℃
lower than that when Sc=0.
-1999~+4000
Scx Input offset For two-wire RTD inputs, the actual offset = (Sc x signal
units or 0.1℃
unit). The signal unit of Pt100 or 0~400ohm input is
0.02ohm, and that of Cu50 or 0~240ohm input is
0.012ohm. For example, when Sc=-50, input type is
Pt100, (-50 x 0.02ohm), then the actual offset= -1.

The value of dF will determine the ability of filtering noise.

dL=0, no filtering;
dL=1, filtering with mean;
dL=2~40, filtering with mean and integral.
When a large value is set, the measurement input is
stabilized but the response speed is slow. Generally, it
dLx Digital filter 0~40
can be set to 1 to 3.
If great interference exists, you can increase parameter dF
gradually to make momentary fluctuation of measured
value less than 2 to 5.
When the instrument is being metrological verified, dF can
be set to 0 or 1 to shorten the response time.
 Yudian (H.K.) Automation Technology Co. Ltd.
Website: [Link] [Link]
Email: sales@[Link] Tel: +852-2770
8785 Fax: +852-2770 8796
From right side to left side, the first, second digit of AOP
respectively indicate the alarm output assignment of [Link],
[Link], as below:
_______ _______
ALPx =
[Link] [Link]

Regarding to parameter value: 0 refers no output.

1,2,3,4,5,6,7 respectively sends alarm output to OP1,
OP2, AL1, AL2, AU1, AU2 and MIO. Shown as below:
[Link] [Link]
No alarm 0 0
OP1 1 1
ALPx Alarm output OP2 (L5 need) 2 2 0~77
AL1 3 3
AL2 (L5 need) 4 4
AU1 5 5
AU2 (L5 need) 6 6
MIO 7 7

For example:
ALP1=43, low limit alarm ([Link]) of channel 1 output to AL2,
ALP2=53, low limit alarm ([Link]) of channel 2 output to AU1,
and both high limit alarms([Link]) of both channel are sent to
AL1.

Define actual number of input channels. 702M: 0~ 2

Number of
Cn When Cn=2, the lower display the present value of 704M: 0~ 4
input channels
channel 2 instead of the channel number. 706M: 0~ 6

Define the initial channel number, shown on lower display,

Initial channel
Cno If instrument A is showing CH1~CH6, set Cno=7 in
number
instrument B, it shows CH7~12. (704M, 706M only)
 Yudian (H.K.) Automation Technology Co. Ltd.
Website: [Link] [Link]
Email: sales@[Link] Tel: +852-2770
8785 Fax: +852-2770 8796

AF is used to select advanced function. The value of AF

is calculated as below:
AF=Ax1 + Bx2 + Cx4 + Dx8 + Ex16

A=0, Slow cyclic display;

A=1, Fast cyclic display.
Above setting only affects display and has no effect on
internal scan speed and alarm response time.
B=0, RTD input use two-wire wiring;
B=1, RTD input use three-wire wiring.
C=0, Only channel 2 is retransmitted to COMM port;
C=1, All input channels are cyclically retransmitted, and
the retransmission time interval on every channel is about
Advanced
3 seconds. The output ranges of all channels are defined
AF function 0~31
by dIL2 and dIH2.
selection
D=0, Normal;
D=1, All low limit alarms are changed to high limit alarm.
E=0, Normal;
E=1, Set M2(MIO) and M3(OUPT) support single channel
input only.

For example, to set a AI-702M with 2 inputs, fast cyclic

display, channel 1 input from three-wire RTD (J0 module
on M1 socket), channel 2 input from thermocouple (J1
module on M2 socket), current retransmission of channel
2 outputted to COMM port, the AF parameter should be
set as below:
A=1,B=1,C=0,D=0, then AF=19.

Single channel relay module provides both normal open

and normal close output, while dual relay output module
only provides NO output.
If L5 dual relay installed, set nonc=0, all in NO status, set
nonc=127, all in NC status.
NO/NC
nonc However, by parameter “nonc”, the NO output can be 0 ~63, 127
selection
changed to NC output.
nonc = Ax1 + Bx2 + Cx4 + Dx8 + Ex16 + Fx32 + Gx64
A,B,C,D,E,F,G respectively set NO/NC output of OP1,
OP2, AL1, AL2, AU1, AU2 and MIO. 0 means the
corresponding output is NO, and 1 means NC output.

OPn=0, OUTP port is for alarm output.

OPn=1~4, OUTP port is used for retransmission of
Select the channel OPn.
OPn channel to be OPn=7, Re-transmit the minimum value, among all 0~4, 7~8
retransmitted channels (defined by Cn) to OUTP
OPn=8, Re-transmit the maximum value, among all
channels (defined by Cn) to OUTP
 Yudian (H.K.) Automation Technology Co. Ltd.
Website: [Link] [Link]
Email: sales@[Link] Tel: +852-2770
8785 Fax: +852-2770 8796

Low limit of
OPL retransmission When OUTP works as re-transmitter, OPL/OPH define the 0~110
current low/high limit of re-transmisson. The unit is 0.1mA.
For example, to transmit the channel 1 input 0~600℃ into
High limit of 4~20mA output, the parameters should be set as below:
OPH retransmission dIL1=0, dIH1=600, OPn=1, OPL=40, OPH=200 0~220
current
Atmospheric Defined atmospheric pressure, when dry bulb, wet bulb
Po 1~120.0
pressure humidity measurement activated. Unit = KPa
Defined wind speed, when dry bulb, wet bulb humidity
SPEd Wind speed 0.01~10.00
measurement was activated. Unit = m/S
Every instrument in the same communication line should
be assigned to different communication address. The
Communication communication applies AIBUS protocol. Every input
Addr 0 ~100
address channel takes one address. For example, if Cn=3 and
Addr=10, then the communication address 10~12 are
assigned to the instrument.
When COMM module interface is used for communication,
bAud defines the baud rate with range 300~19200bit/s.

When linear current output module is installed in COMM

socket, and bAud is set to 0~220, the COMM output can
bAud Baud rate work as retransmission output. It can retransmit channel 0 ~19.2K
2 input or cyclically retransmit all input channels into linear
current. bAud defines the output high limit, and Addr
defines the low limit. The unit is 0.1mA. For example,
to output 4~20mA current, Addr should be set to 40, and
bAud=200.
Loc=0: Allow to display and modify the field parameters
only, which is defined in EP1~EP12.
Loc Parameter lock 0 ~9999
Loc=1: Display the field parameters, without modification.
Loc=808: Allow to display and set all parameters.
When configuration of the instrument is completed, most
parameters are able to hide from field operators to avoid
improper configuration.

EP1~EP12 define none or up to 12 field parameters for

operators from parameter table, except EP itself, like
H.AL1, L.AL1 [Link].

Field If the number of field parameters required is less than

EP1-12 NonE~bAud
parameter 12(sometimes even none), define field parameters from
small number, the next unused EP set to NonE.
E.g. Six parameters of H.AL1 to H.AL6 (all channels’ upper
alarm) are need to be modified by field operators, EP
setting are as follows:
EP1=H.AL1, EP2=H.AL2, EP3=H.AL3, EP4=H.AL4,
EP5=H.AL5, EP6=H.AL6, EP7=NonE.
If no field parameter is required, just set EP1=NonE, then
set Loc to 0 or 1.
 Yudian (H.K.) Automation Technology Co. Ltd.
Website: [Link] [Link]
Email: sales@[Link] Tel: +852-2770
8785 Fax: +852-2770 8796