Scribd
Upload
414 views1 page

ToolboxTalks D-D Ratio 041315 PDF

This document discusses crane and rigging safety, specifically focusing on multi-part braided slings and D/d ratios. It explains that multi-part braided slings are made by braiding multiple small wire ropes together, allowing for high strength and flexibility. They are useful for heavy lifts that require more capacity than a single-part sling can provide. It also outlines the standard D/d ratio that determines the minimum allowable bending diameter for slings to maintain lifting efficiency and safety. An example problem demonstrates how a multi-part braided sling could be used instead of a single-part sling in a scenario where the bending diameter is too small.

Uploaded by

kaniniuser
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
414 views1 page

ToolboxTalks D-D Ratio 041315 PDF

This document discusses crane and rigging safety, specifically focusing on multi-part braided slings and D/d ratios. It explains that multi-part braided slings are made by braiding multiple small wire ropes together, allowing for high strength and flexibility. They are useful for heavy lifts that require more capacity than a single-part sling can provide. It also outlines the standard D/d ratio that determines the minimum allowable bending diameter for slings to maintain lifting efficiency and safety. An example problem demonstrates how a multi-part braided sling could be used instead of a single-part sling in a scenario where the bending diameter is too small.

Uploaded by

kaniniuser
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
  • ToolBox Talks - D/d Ratio & Multi-Part Braided Slings

TOOLBOX TALKS

ITI salutes National Safety Week with this informative series on Crane & Rigging Safety

D/d Ratio & Multi-Part Braided Slings


The use of multi-part braided slings appears to be
returning to the marketplace. In the fabrication of D/d Ratio
these slings, generally a single wire rope is braided or D = diameter of bend
helically laid back against its own body to form an eye d = diameter of wire rope
& eye sling. By design it allows the sling to have the
relative bendability of the component wire rope plus a
high strength value based on the sum of its parts. The
number of component wire ropes in a multi-part sling
could be as many as nine or as few as three.
One area in which to use multi-part braided slings is
the “super heavyweight” category. A lift may require Standard D/d Ratio for:
a sling capacity that cannot be achieved by a single • Single Part, swaged E/E is 25 x rope diameter
part sling, but can be reached by braiding small com- • Multi-Part Braided E/E is 25 x component
ponent wire ropes together into an eye & eye sling wire rope
configuration.
Example: A 4” single part, swaged E/E sling in a basket Example: A 10” horizontal steel shaft is the lifting
has a rated capacity of 226 tons. The same amount attachment for a pre-fabricated structure. Weight
can be lifted by using a 7-part, 1-5/8” multi-part sling is 18 tons. (It is determined a wire rope sling is the
in a basket hitch. best type of sling for this application.)
A second and more common reason for selecting Options:
multi-part slings is their bendability. If a sling is bent
a) 1-1/8” single part, swaged E/E in a basket hitch
around too small a diameter while making its lift,
will meet the 18 ton requirement; however the
there is a reduction in lifting efficiency. A ratio has
10” steel shaft is too small for 1-1/8” wire rope
been developed to help determine minimum allow-
when applied to D/d ratio. (The standard min-
able bending diameter for slings.
imum bending diameter for 1-1/8” wire rope
sling is 22½”.)
Mike Parnell b) 6 parts of ½” component wire rope braided
• Technical Director/CEO at ITI
• Former Vice Chairman, ASME B30 E/E in a basket hitch will also meet the 18 ton
• Chairman, ASME P30 requirement: the standard minimum bending
• Associate Member, CSA Z150 diameter for ½” wire rope is 10”. (This would be
an ideal choice for this application.)
Mike holds 34 years of progressive experience in wire rope, rigging, and
crane operations in various industries including mining, maritime, electric
utility, pulp and paper, manufacturing, nuclear, oil & gas, and construction.
He has developed innovative training techniques, resource materials,
workbooks, videos and reference cards which are widely used in the rigging
industry today. Through ITI Field Services, Mike and his team provide con-
sulting, accident investigation, and expert witness services.

You might also like