BLTouch-Smart : Auto Bed Leveling Sensor for 3D Printers
BLTouch - Smart Servo No. : 0
G-code
BLTouch-Smart
Available PWM Range Marlin Servo PWM Repetier Servo PWM Smoothieware
Push-pin Down 700 us M340 P0 S700
M280 P0 S10 M280 S3.0
700 us ( 10° ) (10°) (Probe start script )
Push-pin Up 1500 us M340 P0 S1500
M280 P0 S90 M280 S7.0
1500 us ( 90° ) ( 90°) (Probe finished script)
Self-test 1800 us
M280 P0 S120 M340 P0 S1800 M280 S8.4
1800 us ( 120° ) (120°)
Alarm Release
2100 ~ 2400 us
& Push-pin UP M280 P0 S160 M340 P0 S2200 M280 S10.6
2200 us ( 160° ) (150° ~ 180°)
Wiring Test 1200 us
& Touch SW Mode M280 P0 S60 M340 P0 S1200 M280 S5.5
( 60°)
1200 us ( 60° )
Specification BLTouch CAD Dimension
Voltage(Brown-Red wire) 4.8 ~ 5.1 V
Current 15mA
Maximum(Peak) Current 300mA
Z Probe Output Losic 5V / 3.3V(internal)
Color Semitransparent White
SMT & Soldering Lead Free
Cable Length 150±5 mm
Weight 0.35 oz (10g)
3Pin : Brown(-, GND)
Red(+5V)
Wiring Orange(control signal)
2Pin : Black(-, GND)
White(Zmin)
※ Additional power supply can be needed in case which your board does not supply enough amperage.
※ Electronic devices can be damaged or even destroyed if connected to the wrong side polarity.
[wrong terminal connect to 5V(+) and GND(-)]
※ Now, you don't need 240Ω, 10KΩ resistor for 3.3V logic Board
※ The action as pulling/pushing hard the push-pin can make the BLTouch damaged and less accurate.
■ Signal Timing Diagram
Correct position of Core If your board is 3.3V Logic, please following below
[Link] [Link] PayPal Account & Email : antclabs@[Link]
If you want to order through PayPal, please send us e-mail including quantity, address, zip code, phone number and name.
■ Setting (e.g. Marlin firmware)
Please refer to other auto bed leveling setting documents ( Youtube or G+, etc. ).
Troubleshooting : [Link]
Marlin 1.1.x(1.1.6) Setting
Step 1 : Copy the file below and overwrite at the Marlin folder. <== e.g. Delta
Marlin\example_configurations\delta\generic\Configuration.h
Marlin\example_configurations\delta\generic\Configuration_adv.h
Step 2 : Look at the Configuration.h at your previous firmware and edit Configuration.h at Marlin 1.1.x
Step 3 : Check your 3D printer works well.
Step 4 : Please install your BLTouch.
Step 5 : Edit Configuration.h and Configuration_adv.h like below.
■ Configuration.h
//============================== Endstop Settings ===========================
#define USE_ZMIN_PLUG
//============================= Z Probe Options =============================
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
//#define Z_MIN_PROBE_ENDSTOP
//#define FIX_MOUNTED_PROBE
#define BLTOUCH
#if ENABLED(BLTOUCH)
#define BLTOUCH_DELAY 100 // *option
#endif
#define PROBING_HEATERS_OFF // *option
#define PROBING_FANS_OFF // *option
#define X_PROBE_OFFSET_FROM_EXTRUDER 0 //Your BLTouch X_PROBE_OFFSET_FROM_EXTRUDE
#define Y_PROBE_OFFSET_FROM_EXTRUDER -22 //Your BLTouch Y_PROBE_OFFSET_FROM_EXTRUDE
#define Z_PROBE_OFFSET_FROM_EXTRUDER -1.9 //Your BLTouch Z_PROBE_OFFSET_FROM_EXTRUDE
#define Z_CLEARANCE_DEPLOY_PROBE 15 // set up at least 15
#define Z_CLEARANCE_BETWEEN_PROBES 10 // set up at least 10
//=============================== Bed Leveling ==============================
// Choose a line of below lines and remove // at the start of the line
//#define AUTO_BED_LEVELING_3POINT
//#define AUTO_BED_LEVELING_LINEAR
#define AUTO_BED_LEVELING_BILINEAR
//#define AUTO_BED_LEVELING_UBL
//#define MESH_BED_LEVELING
//============================= Additional Features ===========================
#define EEPROM_SETTINGS // Enable for M500 and M501 commands
//=========================== R/C SERVO support ==========================
#define NUM_SERVOS 3 // set up at least 1
#define SERVO_DELAY { 300, 300, 300 }
Previous Versions before Marlin RC7
■ Configuration.h
//============================= Mechanical Settings =========================
const bool Z_MIN_ENDSTOP_INVERTING = false;
//============================= Z Probe Options ============================
//#define Z_MIN_PROBE_ENDSTOP // *RC4 ~ RC6
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN // *RC4 ~ RC6
//============================ Bed Auto Leveling ============================
#define AUTO_BED_LEVELING_FEATURE
#define X_PROBE_OFFSET_FROM_EXTRUDER 20 //Your BLTouch X_PROBE_OFFSET_FROM_EXTRUDE
#define Y_PROBE_OFFSET_FROM_EXTRUDER -20 //Your BLTouch Y_PROBE_OFFSET_FROM_EXTRUDE
#define Z_PROBE_OFFSET_FROM_EXTRUDER -1.0 //Your BLTouch Z_PROBE_OFFSET_FROM_EXTRUDE
#define Z_SAFE_HOMING
//============================ R/C SERVO support ==========================
#define NUM_SERVOS 3
#define SERVO_ENDSTOP_ANGLES {{0,0}, {0,0}, {10,90}} // 10=deploy, 90=retract
//#define DEACTIVATE_SERVOS_AFTER_MOVE
If you want more additional information about the other versions, please visit our website, [Link]
