Figure B
Framing
FR AMING SEQUENCE
Wall framing
Pre-assembled dormer wall
Roof framing (install after
wall sheathing)
Pre-assembled “ladder”
Dormer sheathing nailers
Cross-ties
Install after main roof sheathing
Figure C 2x6 x 18' 0" RIDGE.
ALL OTHER PIECES ARE 2x4s
Left & Right Wall Framing
RAFTER
A
EXTERIOR
12
SECTION A-A
9 4' 8-5/16"
A
1 1 16-1/4"
ORANGE
REAR PIECES FRONT
- LEFT WALL 48"
WALL WALL
ONLY
8' 1-1/8"
2x4 TREATED
BOTTOM 35-1/2"
PLATE
20-1/2" 24" O.C. 20-1/2"
11' 5"
12' 0"
Figure D
Front & Rear Wall Framing
NOTE: ALL BLUE PIECES - FRONT WALL ONLY ALIGN LIGHT
A BLUE STUDS
WITH WALL
STUDS BELOW.
19-1/2"
2' 5-9/16"
19-1/2"
A
DOUBLED
2x10s SECTION A-A
- ALL OTHER
PIECES
ARE 2x4s
8' 1-1/8"
ORANGE
6' 11-3/8"
PIECES
- REAR WALL
ONLY
2x4 TREATED 7' 7-1/2"
BOTTOM
PLATE
24" 24" O.C. 24" O.C. 24"
16' 0"
Figure E
Left & Right Wall Sheathing
NOTCH SHEATHING
AROUND RIDGE
1/2" OSB
SHEATHING
STRIPS
1-1/2" WIDE
OVER WALL
8' STUDS
4' 4' 4'
REAR WALL ALIGN BOTTOM EDGES
FRAMING (REF) OF WALL SHEATHING
WITH LOWER EDGE OF
BOTTOM PLATES.
NOTE: 1/2" OSB SHEATHING. MAKE CUT-OUTS
FOR WINDOWS AND ADD 1-1/2" STUD
STRIP IN LEFT WALL ONLY.
Figure F
Front & Rear Wall Sheathing
1/2" x 4-1/2"
OSB STRIPS
1/2" x 2-1/4"
8' OSB STRIPS
4'
ALIGN BOTTOM EDGES NOTE: 1/2" OSB SHEATHING. FRONT WALL SHEATHING SHOWN.
OF WALL SHEATHING FOR REAR WALL, USE FOUR 4'x8' PANELS.
WITH LOWER EDGE OF
BOTTOM PLATES.
Figure G 12
DORMER SIDEWALL
Rafters 4 NAILER (LEFT WALL
1 SHOWN; RIGHT WALL 1 3
Installation IS OPPOSITE)
1 3
INSTALL CENTER 7
REAR RAFTERS 6
OPPOSITE DORMER
RAFTERS.
ROOF
2 1/4"
SHEATHING
(REF.)
7
3/8" 4
SECTION A-A 2 BEVEL CORNER 5
SECTION B-B SECTION C-C
(TYPICAL ALL
SUBFSACIAS)
A B C C C
18' 0"
12' 1-1/2"
24" 24-3/4"
O.C.
A B C C C
2x4
SUBFASCIA
NOTE: ALL 2x4 CONSTRUCTION. FRONT OVERHANG LADDER (GREEN PIECES)
IS PRE-ASSEMBLED, THEN INSTALLED WITH TOP SURFACES OF SMALL
RAFTERS ( 4 5 ) FLUSH WITH TOP SURAFCES OF 1 RAFTERS.
Figure G1
Front Overhang Strap
SIMPSON
LSTA24
OR SIMILAR
Figure H 3A
Roofs & Dormer SOFFIT
NAILER
2x4
SUBFASCIA
Side Walls 1/2" OSB
SHEATHING 1/4"
Sheathing
1"
BEVEL CORNER
SOFFIT
1/2" OSB
SHEATHING
SECTION A-A
3A 1/2" OSB
SUBFASCIA SOFFIT SHEATHING
SOFFIT
2
SOFFIT
NAILER 2x4 x 14' 1"
12-1/2" SUBFASCIA 12-1/2"
1/2" OSB
SHEATHING
SIDE WALL
A
Figure J 1x6
PVC
Side Wall
SHINGLE
TRIM TRIM 1x6
PVC
Siding & Trim 1x4 TRIM
PVC
TRIM
SHINGLE
TRIM
1x2 1" x 7-1/4"
DRIP PVC TRIM
CAP
B B
2
SUBFASCIA
A (ref.)
TRIM
(CUT TO FIT) SOFFIT
(ref.)
1x2
STOP
1x6
PVC
TRIM
ALUMINUM
STORM 1x6
WINDOW PVC
B B TRIM 1x6
RIPPED
C C PVC
TO TRIM
1" x 3-1/2" 4-3/4"
SILL 1x4
PVC
TRIM
SECTION B-B
A (SECTION C-C
OPPOSITE)
1x6
SECTION A-A
PVC
TRIM
HOUSE
2x4 TREATED
WRAP
DOOR GUIDE
1x4 5/16"
PVC FIBER-CEMENT
TRIM SIDING NOTE: LEFT WALL SHOWN. FOR RIGHT WALL, OMIT WINDOWS
AND COVER SIDING JOINTS WITH 1x4 TRIM.
1x6 TRIM 1x6 TRIM
Figure K RIPPED 1x4 RIPPED 1x6 SHINGLE TRIM 1x6
TO 4-3/4" TRIM TO 4-1/2" FASCIA TRIM (CUT TO FIT) TRIM
Front Wall
Siding & Trim
1-1/2" x 2"
TRACK
MOUNT B
1x6 2-3/4" 1x4
PVC 1x6 TRIM
TRACK
TRIM RIPPED
COVER
TO 4-3/4"
VIEW A-A A A
1x6 DORMER FIBER-CEMENT
PVC 1x4 FLASHING SIDING
TRIM 1x4 TRACK B SHINGLE
TRIM COVER TRIM
1x2 ALUMINUM
STOP STORM 1x6
WINDOW FASCIA
1" x 3-1/2" 1x6
SILL PVC
APRON
TRIM
1x6 1-1/2" x 2"
PVC TRACK
TRIM MOUNT
1x4
TRACK
COVER
1x4
TRIM
BYPASS
DOOR
TRACK
DOOR
SECTION B-B 2x4 TREATED 1x4 SHOP-MADE DOORS NOTE: Shingles omitted from
DOOR GUIDE TRIM (SEE FIGURE M) main view for clarity.
Figure L 9' 4-3/4"
1-7/8"
Rafters & 53˚ 53˚
Cross-ties
Patterns RAFTER 1 (13 REQ’D) 20-3/8"
9' 4-3/4"
53˚ 53˚
OVERHANG RAFTER 2 (8 REQ’D - 4 USED AS SOFFIT NAILERS)
7' 2-3/4"
7/8" 71.5˚
71.5˚
DORMER RAFTER 3 (7 REQ’D)
10"
7' 1-1/8"
18.4˚ 71.5˚
OVERHANG RAFTER 3A (4 REQ’D - 2 USED AS SOFFIT NAILERS)
21-1/8" 19-1/4"
53˚ 53˚ 53˚ 53˚
RAFTER 4 (2 REQ’D) RAFTER 5 (5 REQ’D)
9' 3/8"
37˚ 18.4˚
CROSS-TIE 6 (3 REQ’D)
11' 10-1/2"
37˚
1-1/2"
CROSS-TIE 7 (3 REQ’D) 2"
NOTE: ALL 2x4 CONSTRUCTION.
Figure M
Shop-made Door 40-7/8"
1x2
PVC
17-3/4"
86"
78-7/8"
59"
10"
10"
10"
1x4 PVC
3/8" 1x4
CEMENT PVC
BOARD 1x6 PVC
(4 PERIMETER
BOARDS)
48"
Figure N
Sliding Door Bottom
DOOR
WASHERS
TREATED 2X4
ANGLE IRON
FENDER WASHER
5/16” LAG SCREW
