CALCULATIONS FOR DESIGN PARAMETERS OF TRANSFORMER
Design Parameters of Transformer:
For Quick review and summary of Calculations, see the tables at the end of this article.
(Table 1) (Table 2) For better understandings, go through the following steps for
calculations. Make sure you have knowledge of Basics of Transformer.
Design Parameters:
For designing a transformer, we need:
1. Power rating
2. Voltage levels (primary and secondary)
3. Currents on both sides
4. Primary and secondary coils wire diameter/size
5. Iron Core area
6. Numbers of turns (primary and secondary)
We are going to design a 50 VA step down transformer of 230V to 12V. Necessary
calculations along with formulae are given below in details:
As we are going to design small transformer (of small power rating) so we are neglecting
core and copper losses as they doesn’t matters in small transformers and seriously
considered in designing power transformers (high power rating transforms).
Calculations:
1. Core Calculations:
Calculate area of core (central limb) by using following formula:
Ai= area of core
F= operating frequency
Bm= magnetic flux density
Te= turns per volts
Assumptions:
So, we know the frequency of the power system. We need magnetic flux and turns per
volts. For designing a small transformer magnetic flux density is averagely taken as 1 to
1.2.
By putting values we will get the area of core.
Current density of copper wire is taken as 2.2 A / mm2 to 2.4 A/ mm2 (approximately).
So, putting values:
F= 50 hz
Bm = 1.2 wb/m2
Te = 4 (turns per volts)
As, we are going to design a practical transformer so we must consider the core available in
market. The standard Bobbins available in market practically is 1”x1”, 1.25”x1.5”, 1.5”x1.5”
and so on. We took nearest core area available to our calculation. We took bobbin of 2.25
inch2 (1.5”x1.5”) or 0.00145161 meter square. We have the core area. We can calculate
turns per volts using this area by following:
Putting:
f=50 hz;
Bm = 1.2 wb/(m^2);
Ai= 0.001451 m^2,
we got:
So, Turns per volts are 2.6 Turns per volts.
Primary Winding Calculations
Primary voltage = Vp = 230 V
Primary current = I1= VA / Vp = 50 / 230 = 0.218
Let transformer we are going to design is 95 % efficient so,
I1 = VA/ (efficiency x Vp) = 0.23A
Primary Current = 0.23 Amp (approx.)
Number of Turns:
Total number of turns = turns per volts x primary side voltage
= 2.6 x 230
N1 = 600 turns (approximately)
Size of Conductor:
As we know that
As, for copper the current density is taken as 2.3 A per mm square So, for area of copper
conductor
From the standard American wire gauge table, we can choose wire of the same thickness.
It can be seen that it comes out that required primary side wire is of 27 gauge which can
conduct required current.
Selection of wire can also be done by calculating primary current and by cross match the
standard table of copper wire according to their current handling capabilities.
Secondary Winding Calculations
Secondary voltage = Vs = 12 V
Secondary current = Is = VA/ Vs = 50 / 12 = 4.2 Amp (approx.)
From the standard copper wire, table it can be seen that wire of this thickness is of 15
gauge. So for secondary winding we need 15 gauge wire.
So,
Secondary Wire =15 AWG
Number of Turns:
Number of secondary turns = turns per volts x secondary volts
N2 = 2.6 x 12 = 32 turns (approx.)
Weight Estimation of Windings
For weight calculations, following steps will be followed:
Approximate length of copper wire = perimeter of bobbin x number of turns
Cross sectional Area of copper conductor
Volume = Approximate length x Cross sectional area
Mass = density of copper x Volume
Density of copper = 8960 kg/ m3
Primary side:
Perimeter of bobbin = (1.75 x 4) = 7 inch = 0.1778 m
So,
Length of one turn = 0.1778 m
Total length of all turns of primary = L1
L1 = (length of one turn) x(total number of turns of primary)
L1 = 0.1778 x 600
L1 = 106 m (approx.)
As,
area of primary conductor = 0.1 mm2
= (0.1 x 10 ^ -6) m2
Volume of copper wire = area x length
And
density of copper = 8960 kg/ m3
So,
So we need approx. 100 grams of 27 gauge wire.
Secondary winding weight:
Perimeter of bobbin = (1.75 x 4) = 7 inch = 0.1778 m
So,
Length of one turn = 0.1778 m
Total length of all turns of Secondary
= L2 = length of one turn x total number of turns of secondary
L2 = 0.1778 x 32
L2 = 6 m (approx.)
As,
area of primary conductor = 1.83 mm2 = (1.83 x 10 ^ -6) m2
Volume of copper wire = area x length
So, we need approx. 100 grams of 15 gauge wire.
So, from above calculations we can summarize in following table:
Table 1: Calculation for primary side
Table 2: Design Summary for Secondary of transformer design
