User Manual

ITA-1711 Series

Fanless Embedded Celeron

Dual Core Compact Industrial
Computer
嵌入式無風扇電腦
Copyright
The documentation and the software included with this product are copyrighted 2015
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. How-
ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-
ments of the rights of third parties, which may result from its use.

Acknowledgements
The ITA-1711 is trademark of Advantech Co., Ltd.
All other product names or trademarks are properties of their respective owners.

On-line Technical Support

For technical support and service, please visit our support website at:
[Link]

ITA-1711 User Manual ii

Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of pur-
chase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defec-
tive, it will be repaired or replaced at no charge during the warranty period. For out-
of-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandize
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.

Part No. 2001171130 Edition 1

Printed in China December 2015

iii ITA-1711 User Manual

A Message to the Customer
Advantech Customer Services

Each and every Advantech product is built to the most exacting specifications to
ensure reliable performance in the harsh and demanding conditions typical of indus-
trial environments. Whether your new Advantech equipment is destined for the labo-
ratory or the factory floor, you can be assured that your product will provide the reli-
ability and ease of operation for which the name Advantech has come to be known.
Your satisfaction is our primary concern. Here is a guide to Advantech's customer
services.
To ensure you get the full benefit of our services, please follow the instructions below
carefully.

Technical Support

We want you to get the best performance possible from your products. If you run into
technical difficulties, we are here to help. For the most frequently asked questions,
you can easily find answers in your product documentation. These answers are nor-
mally a lot more detailed than the ones we can give over the phone.
Please consult this manual first. If you still cannot find the answer, gather all the infor-
mation or questions that apply to your problem, and with the product close at hand,
call your dealer. Our dealers are well trained and ready to give you the support you
need to get the most from your Advantech products. In fact, most problems reported
are minor and can be easily solved over the phone.
In addition, free technical support is available from Advantech engineers every busi-
ness day. We are always ready to give advice about application requirements or spe-
cific information on the installation and operation of any of our products.

Initial Inspection
When you open the carton, please make sure that the following materials have been
shipped:
 1 x ITA-1711 series industrial computer
 1 x ITA-1711 Accessory box
 1 x Warranty Card

If any of these items are missing or damaged, contact your distributor or sales repre-
sentative immediately. We have carefully inspected the ITA-1711 mechanically and
electrically before shipment. It should be free of marks and scratches and in perfect
working order upon receipt. As you unpack the ITA-1711, check it for signs of ship-
ping damage. (For examples: box damage, scratches, dents, etc.) If it is damaged or
it fails to meet the specifications, notify our service department or your local sales
representative immediately. Also, please notify the carrier. Retain the shipping carton
and packing material for inspection by the carrier. After inspection, we will make
arrangements to repair or replace the unit.

ITA-1711 User Manual iv

Warnings, Cautions, and Notes

Warning! Warnings indicate conditions, which if not observed, can cause personal
injury!

Caution! Cautions are included to help you avoid damaging hardware or losing
data. e.g.
There is a danger of a new battery exploding if it is incorrectly installed.
Replace the battery only with the same or equivalent type recom-
mended by the manufacturer. Discard used batteries according to the
manufacturer's instructions.

Note! Notes provide optional additional information.

警告使用者！這是甲類的資訊產品，在居住的環境中使用時，可能會造成射頻干擾，
在這種情況下，使用者會被要求採取某些適當的對策。

v ITA-1711 User Manual

Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equip-
ment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage.
7. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
8. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
9. All cautions and warnings on the equipment should be noted.
10. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient overvoltage.
11. Never pour any liquid into an opening. This may cause fire or electrical shock.
12. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
If one of the following situations arises, get the equipment checked by service
personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work well, or you cannot get it to work according to
the user's manual.
The equipment has been dropped and damaged.
The equipment has obvious signs of breakage.
13. Do not leave this equipment in an environment unconditioned where the storage
temperature under 0° C (32° F) or above 40° C (104° F), it may damage the
equipment.
14. This equipment has been tested and found to comply with the limits for a Class
A digital device. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the
interference at his own expense.
15. Advantech doesn’t provide power component for this product, users should pur-
chase power components with CCC certificate.
16. CAUTION: The computer is provided with a battery-powered real-time clock cir-
cuit. There is a danger of explosion if battery is incorrectly replaced. Replace
only with same or equivalent type recommended by the manufacturer. Discard
used batteries according to the manufacturer's instructions.
17. The sound pressure level at the operator's position according to IEC 704-1:1982
is no more than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech
disclaims all responsibility for the accuracy of any statements contained herein.

ITA-1711 User Manual vi

Safety Precaution - Static Electricity
Follow these simple precautions to protect yourself from harm and the products from
damage.
1. To avoid electrical shock, always disconnect the power from your PC chassis
before you work on it. Don’t touch any components on the CPU card or other
cards while the PC is on.
2. Disconnect power before making any configuration changes. The sudden rush
of power as you connect a jumper or install a card may damage sensitive elec-
tronic components.

vii ITA-1711 User Manual

ITA-1711 User Manual viii
Contents
Chapter 1 Overview...............................................1
1.1 Introduction ............................................................................................... 2
1.2 Specifications ............................................................................................ 2
1.3 Power Information ..................................................................................... 2
Table 1.1: Power ......................................................................... 2
1.4 Environmental Specifications .................................................................... 3
Table 1.2: Environmental Specifications ..................................... 3
1.5 Dimension Diagram................................................................................... 3
Figure 1.1 Dimension Diagram of ITA-1711 ................................ 3
1.6 Exploded Diagram..................................................................................... 4
Figure 1.2 Exploded Diagram of ITA-1711 .................................. 4
Table 1.3: Part List ...................................................................... 4

Chapter 2 H/W Installation....................................5

2.1 Introduction ............................................................................................... 6
2.2 System Status Indicators .......................................................................... 6
2.2.1 System Status LED Indicators ...................................................... 6
Figure 2.1 Front panel indicators ................................................. 6
Figure 2.2 Rear panel indicators.................................................. 6
2.3 Jumpers and Connector............................................................................ 7
2.3.1 Jumper Description ....................................................................... 7
2.3.2 Jumper and Connector Location................................................... 8
Table 2.1: Jumpers...................................................................... 8
Figure 2.3 Motherboard Connectors and Jumpers Location ....... 9
Figure 2.4 Expansion I/O Card Connectors and Jumpers Location
.................................................................................... 9
Table 2.2: JLVDS1: LVDS Voltage Selection ............................ 10
Table 2.3: JCOMS1: Clear COMS Selection............................. 10
Table 2.4: VCCGPIO1: GPIO Voltage Selection ....................... 10
Table 2.5: PSON1: Start-up Mode Selection............................. 10
Table 2.6: AMPL1: L Sound Channel Amplifier Switch ............. 11
Table 2.7: AMPR1: R Sound Channel Amplifier Switch ............ 11
2.4 I/O Connector.......................................................................................... 12
Figure 2.5 ITA-1711-00A1E, ITA-1711-10A1E, ITA-1711-20A1E
Front I/O Interfaces................................................... 12
Figure 2.6 ITA-1711-S0A1E Front I/O Interfaces ...................... 12
Figure 2.7 ITA-1711-00A1E Rear I/O Interfaces ....................... 12
Figure 2.8 ITA-1711-10A1E Rear I/O Interfaces ....................... 13
Figure 2.9 ITA-1711-20A1E Rear I/O Interfaces ....................... 13
2.4.1 COM Connectors ........................................................................ 13
2.4.2 USB Connector ........................................................................... 14
2.4.3 VGA Connector........................................................................... 14
2.4.4 DIO Connector ............................................................................ 15
2.4.5 Audio in Connector ..................................................................... 15
2.4.6 LAN Connector ........................................................................... 15
2.4.7 Phoenix Terminal Connector ...................................................... 16
2.4.8 LVDS Connector ......................................................................... 16
2.4.9 LPT Connector............................................................................ 17

Chapter 3 System Setup .....................................19

3.1 Introduction ............................................................................................. 20

ix ITA-1711 User Manual

 3.1.1 Installing the Motherboard M-sata Card ..................................... 20
Figure 3.1 Installing the Motherboard CF Card ......................... 20
3.1.2 Installing the Mini PCIe Card ...................................................... 21
Figure 3.2 Installing the Mini PCIe Card.................................... 21
3.1.3 Installing the HDD Module .......................................................... 22
Figure 3.3 Installing the HDD Module........................................ 23
3.1.4 Installing the Top Cover.............................................................. 24
Figure 3.4 Installing the Top Cover ........................................... 24
3.1.5 Installing the Mounting Bracket................................................... 25
Figure 3.5 Installing the Mounting Bracket ................................ 25
3.1.6 Installing the CF Card Module .................................................... 25
Figure 3.6 Installing the CF Card Module.................................. 25

Chapter 4 AMI BIOS............................................ 27

4.1 Introduction ............................................................................................. 28
Figure 4.1 Setup Program Initial Screen ................................... 28
4.2 Entering Setup ........................................................................................ 29
Figure 4.2 Press <DEL> to Enter Setup .................................... 29
4.2.1 Main Setup.................................................................................. 30
Figure 4.3 Main Setup Screen................................................... 30
4.2.2 Advanced BIOS Features Setup................................................. 31
Figure 4.4 Advanced BIOS Features Setup Screen.................. 31
Figure 4.5 ACPI Settings ........................................................... 32
Figure 4.6 Super I/O configuration ............................................ 34
Figure 4.7 Current System Temperature and Voltage............... 36
Figure 4.8 CPU Configuration ................................................... 37
Figure 4.9 IDE configuration...................................................... 38
Figure 4.10USB configuration .................................................... 39
4.2.3 Advanced Chipset Settings......................................................... 40
4.2.4 Security Setup ............................................................................ 43
Figure 4.11Password Configuration ........................................... 43
4.2.5 Boot Setup .................................................................................. 44
Figure 4.12Boot Configuration.................................................... 44
4.2.6 Save and Exit.............................................................................. 45

Chapter 5 Driver Installation.............................. 47

5.1 Introduction ............................................................................................. 48
5.2 Driver Installation .................................................................................... 48
5.2.1 Chipset Windows Driver Setup ................................................... 49
5.2.2 VGA Windows Driver Setup........................................................ 49
5.2.3 LAN Windows Driver Setup ........................................................ 50
5.2.4 AUDIO Windows Driver Setup.................................................... 50

Chapter 6 GPIO Programming Guide ............... 51

6.1 ITA-1711 Digital DIO Definition............................................................... 52
6.2 Configuration Sequence ......................................................................... 52
6.3 Function Call Reference ......................................................................... 52

Appendix A Programming the Watchdog Timer . 55

A.1 Watchdog Timer Overview...................................................................... 56
A.2 Programming the Watchdog Timer ......................................................... 56
Table A.1: Watchdog Timer Registers....................................... 56
A.3 Program Examples ................................................................................. 57

ITA-1711 User Manual x

 Chapter 1
1 Overview
This chapter provider general
Information about the ITA-1711.
1.1 Introduction
The ITA-1711 is a fan-less compact industrial computer chassis with Celeron dual
core processor and wide voltage input range, which is specially designed for intelli-
gent transportation - E-police applications. This powerful computing platform can
stand operation under harsh conditions 24 hours a day, 7 days a week.

1.2 Specifications
 System Chipset: Intel® Celeron processor J1900
 BIOS: AMI SPI 64 Mb Flash
 System Memory: On-board 4GB DDR3L 1333
 Display: Embedded Gen7 GFX Core, Frequency 542MHz
Up to 256 MB SDRAM shared system memory
 Dual Display: Single display resolution up to 2560 x 1600@ 60Hz
Dual Display resolution up to 1920 x 1200@ 60Hz
 Storage: Supports 1 M-SATA slot, 1 CF slot, 1 2.5” HDD slot
 Expansion Slot: Supports 1 Mini PCIe slot
 Ethernet: 2 x 10/100/1000M Ethernet RJ45 port
 USB: 5 x USB2.0, 1 x USB3.0
 VGA: 2 x VGA
 Serial I/O: 10 x COM port, RS-232/422/485 switchable (4 COM optional for RS-
232 switch)
 Digital I/O: 1 x 12-ch GPI, 1 x 12-ch GPO
 Audio: 1 x Speaker out with 2 x 4 W amplifer; 1 Mic input
 Reserved Zone: Optional PCA-5650 graphic card expansion for 2 VGA
 Weight: 3.6 kg
 Dimensions (W x H x D): 200 x 190 x 100 mm

1.3 Power Information

ITA-1711 supports DC 9 ~ 36 V wide voltage input.

Table 1.1: Power

DC voltage input 9 V - 36 V
DC current 6.5 A - 3.25 A
DC power interface 2P Phoenix (European Standard)

ITA-1711 User Manual 2

1.4 Environmental Specifications

Chapter 1
Table 1.2: Environmental Specifications
With industrial HDD: 0 ~ 40°C
Operating Temperature
With CF/M-SATA card: -25 ~ 60 °C
Storage Temperature -40 ~ 85°C
Humidity 95% @ 40º C, non-condensing

Overview
With CF card: 2 Grms @ 5 ~ 500 Hz, random, 1 hr/axis
Vibration With 2.5” HDD: 1 Grms @ 5 ~ 500 Hz, random, 1 hr/axis
IEC60068-2-6 Sine 2G @ 5 ~ 500 Hz, 1 hr/axis
With CF card: 20G, IEC-68-2-27, half sine wave, 11 ms duration
Shock
With 2.5” HDD: 10G, IEC-68-2-27, half sine wave, 11 ms duration
Safety UL, CCC, CE, FCC, CB and BSMI compliant

1.5 Dimension Diagram

Figure 1.1 Dimension Diagram of ITA-1711

3 ITA-1711 User Manual

1.6 Exploded Diagram

Figure 1.2 Exploded Diagram of ITA-1711

Table 1.3: Part List

1 Heat sink 9 Expansion display card
2 Slide rail 10 Expansion I/O card
3 CF adapter board 11 HDD bracket
4 CF extraction rack 12 HDD (not included)
5 CF fixing rack 13 HDD fixed bracket
6 Wall mounting bracket 14 Top cover
7 Main board 15 Replaceable plate
8 Display plate 16 Front panel

ITA-1711 User Manual 4

 Chapter 2
2 H/W Installation
This chapter provides H/W Instal-
lation about the ITA-1711.
2.1 Introduction
The following sections show the internal jumpers setting and the external connectors
pin assignment for application integration.

2.2 System Status Indicators

2.2.1 System Status LED Indicators
The top right LED of the front panel indicates system healthy and active status.

Figure 2.1 Front panel indicators

Figure 2.2 Rear panel indicators

Refer to below table for a LED definition summary.

Item LED Status Color Description

On Green System power is on, system is safe
1 PWR/FAULT
On Red System voltage overheated
On Data being received/transmitted
2 HDD Yellow
Off No data being received/transmitted

ITA-1711 User Manual 6

2.3 Jumpers and Connector

Chapter 2
2.3.1 Jumper Description
You may configure the ITA-1711 to match the needs of your application by setting
jumpers. A jumper is a metal bridge used to close an electric circuit. It consists of two
metal pins and a small metal clip (often protected by a plastic cover) that slides over
the pins to connect them. To close a jumper, you remove the clip. Sometime a jumper
will have three pins, labelled 1, 2 and 3. In this case you would connect either pins 1
and 2, or 2 and 3.

H/W Installation
Open Closed 2-3 Closed

The jumpers setting are schematically depicted in this manual as follows.

Open
断开 Closed
闭合 闭合2-3
2-3Closed

A pair of needle-nose pliers may be helpful when working with jumpers. If you have
any doubts about the best hardware configuration for your application, contact your
local distributor or sales representative before you make any changes. Generally, you
simply need a standard cable to make most connections.

7 ITA-1711 User Manual

2.3.2 Jumper and Connector Location
The board has a number of connectors and jumpers that allow you to configure your
system to suit your application. The table below lists the function of each of the con-
nectors and [Link] locations of jumpers and connector on the board are shown
in Fig 2.3 and Fig 2.4.

Table 2.1: Jumpers

Label Function
JCMOS1 Clear CMOS settings
AMPL1 L sound channel amplifier switch
AMPR1 R sound channel amplifier switch
PSON1 AT/ATX mode selection
VCCGPIO1 GPIO voltage selection
SATA1 SATA data interface 1
SATA2 SATA data interface 2
SATA_PWR1 SATA power interface 1
SATA_PWR2 SATA power interface 2
DP1 DP digital display interface 1
DP2 DP digital display interface 2
LVDS1 LVDS1 resolution adjustment
LVDS2 LVDS2 resolution adjustment
PS/2 Keyboard/mouse
M-SATA M-SATA storage card interface
MiniPCIe MiniPCIe module interface

ITA-1711 User Manual 8

 Chapter 2
LVDS1 Conn. SATA_PWR1 LPC1 Conn. LPT1
DP1 SATA2 SATA1 SATA_PWR2

GPIO

MSATA1 VCCGPIO1

PSON1

H/W Installation
SPI1 BIOS Slot
COM3
SODIMM1 JCMOS1
JCMOS2

AMPL1
AMPR1
MINIPCIE1

LPC2 DP2 BAT1

LVDS2

Figure 2.3 Motherboard Connectors and Jumpers Location

GPIO02 JSETCOM6 JSETCOM7

JSETCOM10
COM6_7

JSETCOM4 JSETCOM5

JSETCOM3 JSETCOM8 JSETCOM9

Figure 2.4 Expansion I/O Card Connectors and Jumpers Location

9 ITA-1711 User Manual

 Table 2.2: JLVDS1: LVDS Voltage Selection
Closed Pins Setting
3-4 +12V
2-4 +5V
4/-6 +3.3V (Default)

+12V +5V +3.3V

Table 2.3: JCOMS1: Clear COMS Selection

Closed Pins Setting
1-2 Normal (+V3.3_SB)*
2-3 Clear CMOS settings
*Default setting

1 2 3 1 2 3

Default setting Clear CMOS selection

Table 2.4: VCCGPIO1: GPIO Voltage Selection

Closed Pins Setting
2-4 +V3.3_SB
1-3 +V5_SB (Default)
4-6 +V3.3
3-5 +V5

1 2 3 1 2 3

+V5_SB +V3.3_SB

Table 2.5: PSON1: Start-up Mode Selection

Closed Pins Setting
1-2 AT mode
2-3 ATX mode*
*Default setting

1 2 3 1 2 3

AT mode ATX mode

ITA-1711 User Manual 10

 Chapter 2
Table 2.6: AMPL1: L Sound Channel Amplifier Switch
Closed Pins Setting
1-2,4-5 L Sound Channel Amplifier Switch ON (Default)
2-3,5-6 L Sound Channel Amplifier Switch OFF (Default)

H/W Installation
Table 2.7: AMPR1: R Sound Channel Amplifier Switch
Closed Pins Setting
1-2,4-5 R Sound Channel Amplifier Switch ON (Default)
2-3,5-6 R Sound Channel Amplifier Switch OFF (Default)

11 ITA-1711 User Manual

2.4 I/O Connector

Figure 2.5 ITA-1711-00A1E, ITA-1711-10A1E, ITA-1711-20A1E Front I/O

Interfaces

Figure 2.6 ITA-1711-S0A1E Front I/O Interfaces

Figure 2.7 ITA-1711-00A1E Rear I/O Interfaces

ITA-1711 User Manual 12

 Chapter 2
H/W Installation
Figure 2.8 ITA-1711-10A1E Rear I/O Interfaces

Figure 2.9 ITA-1711-20A1E Rear I/O Interfaces

2.4.1 COM Connectors

ITA-1711 series provides up to ten D-sub 9-pin connectors for RS-232/422/485.

RS-232 RS-422 RS-485

Pin Signal Name Signal Name Signal Name
1 DCD Tx- DATA-
2 RxD Tx+ DATA+
3 TxD Rx+ NC
4 DTR Rx- NC
5 GND GND GND
6 DSR NC NC

13 ITA-1711 User Manual

 7 RTS NC NC
8 CTS NC NC
9 RI NC NC

2.4.2 USB Connector

ITA-1711 provides five USB2.0 connectors and a USB3.0 connector. They can be
disabled in system BIOS setup.

Pin Signal Name

1 +V5(VCC)
2 USB_data-
3 USB_data+
4 GND

2.4.3 VGA Connector

ITA-1711 offers two D-sub 15-pin female connectors.

Pin Signal Name

1 Red
2 Green
3 Blue
4 NC
5 GND
6 GND
7 GND
8 GND
9 +5V
10 GND
11 NC
12 DDC-DATA
13 H-SYNC
14 V-SYNC
15 DDC-CLK

ITA-1711 User Manual 14

2.4.4 DIO Connector

Chapter 2
ITA-1711 provides a DIO connector that needs cabling.

Pin Signal Name

1-12 Digital input (input)

H/W Installation
13 GND
14-25 Digital output (output)

2.4.5 Audio in Connector

ITA-1711 provides an integrated Mic-in/speaker out audio connector.

2.4.6 LAN Connector

ITA-1711 series provide two Intel I211-AT Ethernet controllers, which are fully compli-
ant with IEEE 802.3u 10/100/1000 Mbps standard.

Pin Signal Name Signal Name

A1/B1 MDIO0+ MDIO0+
A2/B2 MDIO0- MDIO0-
A3/B3 MDIO1+ MDIO1+
A4/B4 MDIO2+ MDIO2+
A5/B5 MDIO2- MDIO2-
A6/B6 MDIO1- MDIO1-
A7/B7 MDIO3+ MDIO3+
A8/B8 MDIO3- MDIO3-
A9/B9 LED GREEN- LED GREEN-
A10/B10 LED GREEN+ LED GREEN+
A11/B11 1000M LED 1000M LED

15 ITA-1711 User Manual

 A12/B12 100m/10M LED 100m/10M LED

2.4.7 Phoenix Terminal Connector

ITA-1711 provides a 2-pin phoenix terminal connectors for power input.

Pin Signal Name

1 Positive
2 GND

2.4.8 LVDS Connector

ITA-1711-20A1E provides a PS/2 interface for mouse or keyboard connection.

Pin Signal Name Pin Signal Name

1 TXL0+ 2 TXL1+
3 TXL2+ 4 TXL3+
5 NC 6 NC
7 NC 8 NC
9 NC 10 TXLCLK-
11 TXL0- 12 TXL1-
13 TXL2- 14 TXL3-
15 NC 16 INVVCC
17 BLENABLE 18 GND
19 TXLCLK+ 20 LCDVCC
21 NC 22 GND
23 GND 24 GND
25 GND 26 NC

ITA-1711 User Manual 16

2.4.9 LPT Connector

Chapter 2
ITA-1711-S0A1E provides a LVDS connector(in accessory box for users to change
by themselves), which could connect a monitor through cables.

H/W Installation
Pin Signal Name Pin Signal Name
1 LPT_z_STB# 14 LPT_AFD#
2 LPT_z_PD0 15 LPT_ERR#
3 LPT_PD1 16 LPT_INIT#
4 LPT_PD2 17 LPT_SLIN#
5 LPT_PD3 18 GND
6 LPT_PD4 19 GND
7 LPT_PD5 20 GND
8 LPT_PD6 21 GND
9 LPT_PD7 22 GND
10 LPT_ACK# 23 GND
11 LPT_BUSY 24 GND
12 LPT_PE 25 GND
13 LPT_SLCT 26 NC

17 ITA-1711 User Manual

ITA-1711 User Manual 18
 Chapter 3
3 System Setup
This chapter introduces the instal-
lationprocess of ITA-1711.
3.1 Introduction
The following procedures will instruct you to install all modules into the ITA-1711 sys-
tem.

3.1.1 Installing the Motherboard M-sata Card

ITA-1711 motherboard front panel includes a M-sata card slot for the user to insert a
M-sata card directly.

Figure 3.1 Installing the Motherboard CF Card

ITA-1711 User Manual 20

3.1.2 Installing the Mini PCIe Card

Chapter 3
The ITA-1711 motherboard supports a Mini PCIe expansion card. Please refer to
theinstallation procedure below.
1. Insert a Mini PCIe card into motherboard PCIe slot.
2. Lock and fix the Mini PCIe card by a copper pillar.

System Setup
Figure 3.2 Installing the Mini PCIe Card

21 ITA-1711 User Manual

3.1.3 Installing the HDD Module
ITA-1711 reserves the space for installing a 2.5" HDD module. Please refer to the fol-
lowing instructions to install the HDD.
1. Place the HDD into 2.5” HDD holder, and lock it with 4 screws.
2. The HDD holder has four semi-circles (two bigger and two smaller) on both
sides, which are used to place rubber cushions, with the black ones for bigger
semi-circles and transparent ones for smaller semi-circles.
3. Place the HDD holder onto HDD bracket, and secure it with four screws.
4. Connect the complete HDD module to the chassis and fix it with four screws.
5. Stick the cooling pad onto the PCB panel of HDD. Please align the cooling pad
with the magnetic head to protect the head from being covered.

ITA-1711 User Manual 22

 Chapter 3
System Setup

Figure 3.3 Installing the HDD Module

23 ITA-1711 User Manual

3.1.4 Installing the Top Cover
Please follow the below procedures to install chassis top cover.
1. Insert the top cover on the chassis front panel from the opening point and place
it well as shown. (See Figure 3.4)
2. Fix the chassis top cover with two screws.

Figure 3.4 Installing the Top Cover

ITA-1711 User Manual 24

3.1.5 Installing the Mounting Bracket

Chapter 3
Align the 2 mounting brackets with the screw holes on the chassis side panel, and
secure them with screws. Top and bottom installation are both supported. (See Fig
3.5)

System Setup
Figure 3.5 Installing the Mounting Bracket

3.1.6 Installing the CF Card Module

Please follow the below steps to install CF card module.
1. Loosen the two screws in the CF module.
2. Insert the CF card into the slot and install the CF fixed cover. (See Figure 3.6)
3. Return and screw the CF card module.

Figure 3.6 Installing the CF Card Module

25 ITA-1711 User Manual

ITA-1711 User Manual 26
 Chapter 4
4 AMI BIOS
This chapter introduces how to
configure AMI BIOS.
4.1 Introduction
AMIBIOS has been integrated into many motherboards for over a decade. This chap-
ter introduces how to configure BIOS for ITA-1711 [Link] the AMIBIOS Setup
program, you can modify BIOS settings and control the special features of your com-
puter. The Setup program uses a number of menus for making changes and turning
the special features on or off. This chapter describes the basic navigation of the ITA-
1711 setup screens.

Figure 4.1 Setup Program Initial Screen

AMI’s BIOS ROM has a built-in Setup program that allows users to modify the basic
system configuration. This type of information is stored in battery-backed up CMOS
so it retains the Setup information when the power is turned off.

ITA-1711 User Manual 28

4.2 Entering Setup

Chapter 4
Turn on the computer to enter POST screen, and BIOS and CPU information will be
[Link] <DEL> and you will immediately be allowed to enter Setup.

AMI BIOS
Figure 4.2 Press <DEL> to Enter Setup

29 ITA-1711 User Manual

4.2.1 Main Setup
When you first enter the BIOS Setup Utility, you will enter the Main setup screen. You
can always return to the Main setup screen by selecting the Main tab. There are two
Main Setup options. They are described in this section. The Main BIOS Setup screen
is shown below.

Figure 4.3 Main Setup Screen

The Main BIOS setup screen has two main frames. The left frame displays all the
options that can be configured. Grayed-out options cannot be configured; options in
blue can. The right frame displays the key legend.
Above the key legend is an area reserved for a text message. When an option is
selected in the left frame, it is highlighted in white. Often a text message will accom-
pany it.
 System Time/System Date
Use this option to change the system time and date. Highlight System Time or
System Date using the <Arrow> keys. Enter new values through the keyboard.
Press the <Tab> key or the <Arrow> keys to move between fields. The date
must be entered in MM/DD/YY format. The time must be entered in HH:MM:SS
format.

ITA-1711 User Manual 30

4.2.2 Advanced BIOS Features Setup

Chapter 4
Select the Advanced tab from the ITA-1711 setup screen to enter the Advanced BIOS
Setup screen. You can select any of the items in the left frame of the screen, such as
CPU Configuration, to go to the sub menu for that item. You can display an Advanced
BIOS Setup option by highlighting it using the <Arrow> keys. All Advanced BIOS
Setup options are described in this section. The Advanced BIOS Setup screen is
shown below. The sub menus are described on the following pages.

AMI BIOS
Figure 4.4 Advanced BIOS Features Setup Screen

31 ITA-1711 User Manual

[Link] APM Configuration

Figure 4.5 ACPI Settings

 Board Power Mode

Show the current startup-up mode.

ITA-1711 User Manual 32

[Link] F818264TH Super I/O; F81826SEC Super I/O; F81826THD Super I/O

Chapter 4
Configuration

AMI BIOS
 Serial Port
Enable or disable the serial port. Default is “Enabled”.
 Change Settings
Set the mode of serial port devices. Default is the standard serial port mode.
 Auto Flow Control
Auto flow control function. Default is “Disabled”.

33 ITA-1711 User Manual

[Link] SH3114 Super IO Configuration

Figure 4.6 Super I/O configuration

 Serial Port1/2/60
This option configures serial port 1/2 base addresses and IRQ, as well as RS-
232/422/485 mode. Serial Port 3 ~ 10 RS-232/422/485 mode configurations are
decided by jumper setting.
 Parallel Port Configuration
This option configures parallel port base addresses and IRQ, as well as RS-232/
422/485 mode.

ITA-1711 User Manual 34

 Chapter 4
AMI BIOS
 Serial Port
Enable or disable the serial port. Default is “Enabled”.
 Serial Port Mode
Configure serial port mode. Default is “RS232”. If it’s “RS485”, the auto flow
control option will be enabled and the default is “Disabled”.
 Change settings
Change IO address and IRQ settings. Default is automatically.
 Device mode
Configure the mode of serial port device. Default is “Normal”.

35 ITA-1711 User Manual

[Link] Hardware Monitor

Figure 4.7 Current System Temperature and Voltage

ITA-1711 User Manual 36

[Link] CPU Configuration

Chapter 4
AMI BIOS
Figure 4.8 CPU Configuration

 Socket 0 CPU Information

This item allows users to check CPU specifications.
 Limit CPUID Maximum
This item allows users to configure the maximum of CPUID limit value.
 Execute-Disable Bit
This item allows users to enable or disable Execute Disable Bit Feature. The
default setting is “Enabled”.
 Intel Virtualization Technology
This item allows users to enable or disable Intel virtualization technology.
Default is “Enabled”.
 Power Technology
This item allows users to enable or disable power management tecnology.
Default is “Energy Efficient”.

37 ITA-1711 User Manual

[Link] IDE Configuration

Figure 4.9 IDE configuration

 Serial-ATA
Default setting is “Enabled”, which enables all SATA resources.
 SATA Test Mode
Default setting is “Enabled”, which enables SATA signal testing mode.
 SATA Speed Support
Default setting is “Gen2”. Select “Gen1” or “Gen2” to change SATA transferring
rate.
 SATA Mode
Default setting is “IDE Mode”. Users can select “IDE Mode” or “AHCI Mode”.

ITA-1711 User Manual 38

[Link] USB Configuration

Chapter 4
AMI BIOS
Figure 4.10 USB configuration

 Legacy USB Support

Enable legacy USB support. Default setting is “Enabled”.
 EHCI Hand-Off
Enable the operation system without EHCI Hand-off.
 XHCI Hand-0ff
Enable the operation system without XHCI Hand-off.
 USB MAass Storage Driver Support
Default setting is “Enabled”. Select “Enable” to support massive USB storage
device.
 USB transfer time-out
Configure the time-out time of USB control and interrupt transfer.
 Device reset time-out
Reset the time-out time for massive USB device.
 Device power-up delay
Configure power-up delay for USB device. Default setting is “Manual”.
 Device power-up delay in seconds
Set the power-up delay time for USB device. Default is “3 seconds”.
Note: If no USB drive/keyboard is detected, it is recommended to change the
delay time to 8 seconds.

39 ITA-1711 User Manual

4.2.3 Advanced Chipset Settings
[Link] North Bridge Chipset Configuration

 Intel IGD configuration

– Intergrated Graphics Device
Enable internal display device. Default setting is “Enabled”.
– IGD Turbo Enable
Enable IGD turbo function. Default setting is “Enabled”.
– GFX Boost
Enable GFX boost function. Default setting is “Disabled”.
– PAVC
Enable audio/video protection control. Default setting is “LITE Mode”.
– DVMT Pre-Allocated
Pre-allocate shared graphic memory on startup-up in DVMT mode. Default
value is “64M”.
– DVMT Total Gfx Mem
Preset the total shared graphic memory in DVMT mode. Default value is
“256M”.
– Aperture Size
Set the size of the MMIO space that the graphic memory is mapped to.
 LCD Control
– Primary IGFX Boot Display
Set the primary display. Default setting is “CRT”. Select the option corre-
sponding to the installed display module.
– Secondary IGFX Boot Display
Set the secondary display. Select the option corresponding to the installed
display module.

ITA-1711 User Manual 40

 – DP 1 LVDS Panel Type

Chapter 4
Configure LVDS display resolution of DP1 interface.
– DP 2 LVDS Panel Type
Configure LVDS display resolution of DP2 interface.

[Link] South Bridge Chipset Configuration

AMI BIOS
 Azalia HD Audio
– LPE Audio Support
Configure LPE audio mode. Default setting is “Disabled”.
– Audio Controller
Configure the detecting option of Azalia device. Default setting is “Enabled”.
 USB configuration
– USB OTG Support
Configure OTG function. Default setting is “Disabled”.
– USB VBUS
Configure VBUS mode. Default setting is “on”.
– XHCI Mode
Configure xHCI controller operation mode. Default setting is “Auto”.
– USB2 Link Power Management
Configure USB2 link power management option. Default setting is “Enabled”.
 PCI Express Configuraion
– PCI Express Port 0
Enable or disable PCI Express interface. Default setting is “Enabled”.
– Hot Plug
Enable or disable PCI Express hot plug function. Default setting is “Enabled”.
– Speed

41 ITA-1711 User Manual

 Set the speed of PCIe interface. Default setting is “Auto”.
– Extra Bus Reserved
Set the amount of reserved extra bus. Default value is “1”.
– Reserved Memory
Set the range of reserved memory. Default value is “10”.
– Reserved Memory Alignment
Set the digit of reserved memory alignment. Default value is “1”.
– Prefetchable Memory
Set the range of prefectable memory. Default value is “10”.
– Prefetchable Memory Alignment
Set the digit of prefectchable memory alignment. Default value is “1”.
– Reserved I/O
Set the range of reserved I/O. Default value is “4”.
 Restore AC Power Loss
Configure the status after restoring from power loss. Default setting is “Last
State”.
 Onboard LAN1 PXE Funtion
Configure onboard LAN1 PXE function. Default setting is “Disabled”.
 Onboard LAN2 PXE Funtion
Configure onboard LAN2 PXE function. Default setting is “Disabled”.
 PCIE LAN Wake up From S4/S5
Configure PCIE LAN wake-up function. Default setting is “Enabled”.

ITA-1711 User Manual 42

4.2.4 Security Setup

Chapter 4
AMI BIOS
Figure 4.11 Password Configuration

Select Security Setup from the ITA-1711 Setup main BIOS setup menu. All Security
Setup options, such as password protection and virus protection are described in this
section. To access the sub menu for the following items, select the item and press
<Enter>:
 Change administrator password
 Change user password

43 ITA-1711 User Manual

4.2.5 Boot Setup

Figure 4.12 Boot Configuration

 Setup Prompt Timeout

Set the timeout time of setup prompt. Default setting is “1s”.
 Quiet Boot
If it’s set to “Disabled”, the BIOS will display normal POST information. If it’s
“Enabled”, the OEM icon rather than POST information will be shown.
 Fast Boot
This item allows BIOS to skip some testing steps of the boot process, so as to
reduce system boot time. Default setting is “Disabled”.
 Bootup Num-Lock State
Enable or disable num-lock.

ITA-1711 User Manual 44

4.2.6 Save and Exit

Chapter 4
AMI BIOS
 Save Changes and Exit
Save settings and exit.
 Discard Changes and Exit
Discard changes and exit.
 Save Changes and Reset
Save settings and reset.
 Discard Changes and Reset
Discard changes and reset.
 Save Changes
Save changed settings.
 Discard Changes
Discard changes that have been made.
 Restore Defaults
Rstore default settings.
 Save as User Defaults
Save as user default settings.
 Restore as User Defaults
Restore as user default settings.
 UEFI?Built-in EFI Shell
Enter built-in EFI shell.
 Launch EFI Shell from filesystem device
Launch EFI shell.

45 ITA-1711 User Manual

ITA-1711 User Manual 46
 Chapter 5
5 Driver Installation
This chapter describes how to
Install drivers.
5.1 Introduction
Advantech offers a complete range of Device Driver and software supports for Win-
dows programming developers. You can apply the Windows Device Drivers to the
most popular Windows Programming tools, such as Visual C++, Visual Basic, Bor-
land C++ Builder and Borland Delphi.

5.2 Driver Installation

Insert the driver CD into your system’s CD-ROM drive. You can see the ITA-1711
driver folder items.

ITA-1711 User Manual 48

5.2.1 Chipset Windows Driver Setup

Chapter 5
Insert the driver CD into your system’s CD-ROM drive. You can see the driver folder
of ITA-1711 series. Navigate to the “00_INF” folder and click “[Link]” to
complete driver installation.

Driver Installation
5.2.2 VGA Windows Driver Setup
Insert the driver CD into your system’s CD-ROM drive. You can see the driver folder
of ITA-1711 series. Navigate to the “01_VGA” folder and click “[Link]” to com-
plete driver installation.

49 ITA-1711 User Manual

5.2.3 LAN Windows Driver Setup
Insert the driver CD into your system’s CD-ROM drive. You can see the driver folder
of ITA-1711 series. Navigate to the “02_LAN” folder and click “[Link]” to com-
plete driver installation.

5.2.4 AUDIO Windows Driver Setup

Insert the driver CD into your system’s CD-ROM drive. You can see the driver folder
of ITA-1711 series. Navigate to the “05_Audio” folder and click “[Link]” to com-
plete driver installation.

ITA-1711 User Manual 50

 Chapter 6
6 GPIO Programming
Guide
This chapter introduces GPIO pro-
gramming Guide.
6.1 ITA-1711 Digital DIO Definition
See Section 2.4.8.

6.2 Configuration Sequence

ITA-1711’s on-board GPIO with LPC bus operates by Lattice CPLD.
The configuration and access to CPLD GPIO IC is completed by IO Space accessing
to the system.
Mapping between GPIO IO Space and corresponding GPIO pins:
Port GPO : IO 0xC10~0xC12 (bit0-bit23) R/W
0xC10:bit0~bit7 GPO(1~8)
0xC11:bit0~bit7 GPO(9~16)
0xC12:bit0~bit7 GPO(17~24)
Port GPI : IO 0xC13~0xC15 (bit0-bit23) R
0xC13:bit0~bit7 GPI(1~8)
0xC14:bit0~bit7 GPI(9~16)
0xC15:bit0~bit7 GPI(17~24)

Note! ITA-1711 uses 48 bit CPLD for GPIO control, 24 GPI and 24 GPO
totally.

If a GPIO Pin is Input, users can read the corresponding input value from bit of IO
Space register.
If a GPIO Pin is Output, users can read the corresponding input value from bit of IO
Space register.

6.3 Function Call Reference

GPIO Analog Code (C language pseudocode)

GPO 4 High Output:

unsigned char data;
data = inportb(0xC10); //First read corresponding IO Space register value
data |= 0x08; //00001000B?set bit 03 as‘1’, meaning output High
outportb(0xC10, data); //output value

Read GPI 9 Input Value:

unsigned char data;
data = inportb(0xC14); //first read corresponding IO Space register value
if (data & 0x01); //00000001B, judge value of bit 0
High // 1 = High
else
Low // 0 = Low

ITA-1711 User Manual 52

 Chapter 6
Note! Please examine the current BIOS version. If it is X006 version or earlier,
please open IO decode manually. The opening method is as follows:
Use [Link] in DOS or RW in XP. The following operation takes DOS
as an example.
Run Adu, select PCI menu and find ISA Bridge line, then press “Enter”
to configure.
Modify 90h,91h and 92h registers under the 256 byte table in ISA con-
figuration page.

GPIO Programming Guide

Modified value: 01h in 90h, 0ch in 91h, and 1Ch in 92h.
Ready for IO operation of GPIO.

53 ITA-1711 User Manual

ITA-1711 User Manual 54
 Appendix A
A Programming the
Watchdog Timer
 The ITA-1711's watchdog timer can be used to monitor system software operation
and take corrective action if the software fails to function within the programmed
period. This section describes the operation of the watchdog timer and how to pro-
gram it.

A.1 Watchdog Timer Overview

The watchdog timer is built into the super I/O controller SMSC SCH3114. It provides
the following user-programmable functions:
 Can be enabled or disabled via user program
 Timer can be set from 1 to 255 seconds or 1 to 255 minutes
 Generates an interrupt or resets signal if the software fails to reset the timer
before time-out

A.2 Programming the Watchdog Timer

The I/O port address of the watchdog timer is A00h (hex).

Table A.1: Watchdog Timer Registers

Address: A00h (hex)
Register Shift Read/Write Description
65 (hex) write Set seconds or minutes as units for the timer.
Write 0 to bit 7: set second as counting unit.
[default]
Write 1 to bit 7: set minutes as counting unit.
66 (hex) write 0: Stop timer [default]
01~FF (hex): The amount of the count, in seconds
or minutes, depends on the value set in register 65
(hex). This number decides how long the watchdog
timer waits for strobe before generating an inter-
rupt or reset signal. Writing a new value to this reg-
ister can reset the timer to count with the new
value.
67 (hex) read/write Configure watchdog timer
Bit 1:Write 1 to enable keyboard to reset the timer,
0 to disable. [default]
Bit 2: Write 1 to enable mouse to reset the timer, 0
to disable.[default]
Bit 7~4: Set the interrupt mapping of watchdog
timer:
1111=IRQ15
……
0011=IRQ3
0010=IRQ2
0001=IRQ1
0000=Disable [default]
68 (hex) read/write Control watchdog timer
Bit0: Read watchdog state; 1=Timer timeout
Bit2: Write 1 to immediately generate timeout sig-
nal, and automatically return to 0 (Write only).
Bit3: Writer 1 to allow triggering of timer timeout
when P20 is effective, 0 to disable. [default]

ITA-1711 User Manual 56

A.3 Program Examples

Appendix A Programming the Watchdog Timer

1. Enable watchdog timer and set 10 sec. as timeout interval
Mov dx,A65h ; Select register 65h, watchdog timer I/O port address A00h+ register
shifts 65h
Mov al,80h ; Set second as counting unit
Out dx,al

Mov dx,A66h ; Select register 66h, watchdog timer I/O port address A00h+ register
shift 66h
Mov al,10 ; Set timeout interval as 10 seconds and start counting
Out dx,al
;-----------------------------------------------------------
2. Enable watchdog timer and set 5 min. as timeout interval
;-----------------------------------------------------------
Mov dx,A65h ; Select register 65h, watchdog timer I/O port address A00h+ register
shifts 65h
Mov al,00h ; Set minute as counting unit
Out dx,al

Mov dx,A66h ; Select register 66h, watchdog timer I/O port address A00h+ register
shifts 66h
Mov al,5 ;Set timeout interval as 5 minutes and start counting
Out dx,al
;-----------------------------------------------------------
3. Enable watchdog timer to be reset by mouse
;-----------------------------------------------------------
Mov dx,A67h ; Select register 67h, watchdog timer I/O port address A00h+ register
shifts 67h
In al,dx
Or al,4h ; Enable watchdog timer to be reset by mouse
Out dx,al
;-----------------------------------------------------------
4. Enable watchdog timer to be reset by keyboard
;-----------------------------------------------------------
Mov dx,A67h ; Select register 67h, watchdog timer I/O port address A00h+ register
shifts 67h
In al,dx
Or al,2h ; Enable watchdog timer to be reset by keyboard
Out dx,al
;-----------------------------------------------------------
5. Generate a time-out signal without timer counting
;-----------------------------------------------------------
Mov dx,A68h ; Select register 68h, watchdog timer I/O port address A00h+ register
shifts 68h
In al,dx
Or al,4h ; Generate a time-out signal
Out dx,al
;-----------------------------------------------------------

57 ITA-1711 User Manual

[Link]
Please verify specifications before quoting. This guide is intended for reference
purposes only.
All product specifications are subject to change without notice.
No part of this publication may be reproduced in any form or by any means,
electronic, photocopying, recording or otherwise, without prior written permis-
sion of the publisher.
All brand and product names are trademarks or registered trademarks of their
respective companies.
© Advantech Co., Ltd. 2015