AP7345D

DUAL 300mA HIGH PSRR LOW NOISE LDO WITH ENABLE

Description Pin Assignments

The AP7345D is a Dual low dropout regulator with high output voltage
accuracy, low RDSON, high PSRR, low output noise and low quiescent
(Top View)
current. This regulator is based on a CMOS process.

VIN1

VIN2
Each of regulators includes a voltage reference, error amplifier,
current limit circuit and an enable input to turn on/ off output. With the
integrated resistor network fixed output voltage versions can be
delivered.
NEW PRODUCT

With its low power consumption and line and load transient response,
the AP7345D is well suited for low power handheld communication

VOUT1

VOUT2
equipment.

The AP7345D is packaged in X2-DFN1612-8 package and allows for X2-DFN1612-8

smallest footprint and dense PCB layout.

Features Applications
 Low VIN and Wide VIN Range: 1.7V to 5.25V  Smart Phone/PAD
 Guarantee Each Channel Output Current: 300mA  RF Supply
 VOUT Accuracy ±1%  Cameras
 Ripple Rejection: 75dB at 1kHz  Portable Video
 Low Output Noise: 60µVrms from 10Hz to 100kHz  Portable Media Player
 Quiescent Current as Low as 50µA  Wireless Adapter
 VOUT Fixed 1.2V to 3.6V  Wireless Communication
 Totally Lead-Free & Fully RoHS Compliant (Notes 1 & 2)
 Halogen and Antimony Free, Green Device (Note 3)

Notes: 1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS), 2011/65/EU (RoHS 2) & 2015/863/EU (RoHS 3) compliant.
2. See [Link] for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free, "Green" and
Lead-free.
3. Halogen- and Antimony-free "Green” products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl) and
<1000ppm antimony compounds.

Typical Applications Circuit

VIN1 VOUT1
VIN1 VOUT1
CIN1
1.0mF EN1 COUT1
1.0mF
AP7345D
VIN2 EN2 VOUT2
VOUT2
VIN2
CIN2 COUT2
1.0mF 1.0mF
GND

AP7345D 1 of 15 December 2018

Document number: DS41528 Rev. 1 - 2 [Link] © Diodes Incorporated
 AP7345D

Pin Descriptions

Pin Number Pin Name Function

GND 1, 4 Ground

VOUT1 2 Channel 1 Output Voltage pin

VOUT2 3 Channel 2 Output Voltage pin

Chanel 2 Enable pin. This pin should be driven either high or low and must not
NEW PRODUCT

EN2 5 be floating. Driving this pin high enables channel 2 output, while pulling it low
puts Chanel 2 regulator into shutdown mode.

VIN2 6 Channel 2 Input Voltage pin

VIN1 7 Channel 1 Input Voltage pin

Chanel 1 Enable pin. This pin should be driven either high or low and must not
EN1 8 be floating. Driving this pin high enables channel 1 output, while pulling it low
puts Chanel 1 regulator into shutdown mode.
In PCB layout, prefer to use large copper area to cover this pad for better
— Thermal PAD thermal dissipation, then connect this area to GND or leave it open. However do
not use it as GND electrode function alone.

Functional Block Diagram

VIN1 VOUT1

R1_1
Error Amp.

R2_1
Vref

Current Limit

EN1 GND

VIN2

R1_2
Error Amp.

R2_2
Vref

Current Limit

EN2 VOUT2

AP7345D 2 of 15 December 2018

Document number: DS41528 Rev. 1 - 2 [Link] © Diodes Incorporated
 AP7345D

Absolute Maximum Ratings (@TA = +25°C, unless otherwise specified. Note 4)

Symbol Parameter Rating Unit

VIN Input Voltage 6.0 V

VEN Input Voltage at EN Pins 6.0 V

VOUT Output Voltage -0.3 to VIN +0.3 V

IOUT Output Current 400 mA

NEW PRODUCT

PD Power Dissipation 600 mW

TA Operating Ambient Temperature -40 to +85 °C

TSTG Storage Temperature -55 to +125 °C

Note 4: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only and functional
operation of the device at these conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device
reliability.

Recommended Operating Conditions (@TA = +25°C, unless otherwise specified.)

Symbol Parameter Min Max Unit

VIN Input Voltage 1.7 5.25 V

IOUT Each Channel Output Current 0 300 mA

TA Operating Ambient Temperature -40 +85 °C

AP7345D 3 of 15 December 2018

Document number: DS41528 Rev. 1 - 2 [Link] © Diodes Incorporated
 AP7345D

Electrical Characteristics (@TA = +25°C, VIN = VOUT+1V (VOUT > 1.5V), VIN = 2.5V (VOUT ≤ 1.5V), IOUT = 1mA, CIN = COUT = 1.0µF,
unless otherwise specified.)

Parameter Conditions Min Typ Max Unit

Input Voltage TA = -40°C to +85°C 1.7 — 5.25 V

TA = +25°C -1 — 1
VIN = (VOUT-Nom+1.0V) to
Output Voltage Accuracy (Note 11) 5.25V, %
IOUT = 1mA to 300mA TA = -40°C to +85°C -1.5 — 1.5
NEW PRODUCT

Line Regulation (∆VOUT/∆VIN/VOUT) VIN = (VOUT-Nom+1.0V) to 5.25V, IOUT = 1.0mA — 0.02 0.1 %/V

Load Regulation VIN = VOUT-Nom+1.0V, IOUT = 1mA to 300mA — 15 30 mV

Set EN1 High, Set EN2 Low, or Set EN2 High,
— 50 70 µA
Quiescent Current (Note 6) Set EN1 Low, No Load
Set EN1/EN2 High, No Load — 100 140 µA

ISTANDBY Set EN1/EN2 Low, No Load — 0.1 1.0 µA

Each Channel Output Current — 300 — — mA

Fold-back Short Current (Note 7) VOUT short to ground — 55 — mA

VIN = (VOUT+1V) VDC +
PSRR (Note 8) 0.2Vp-pAC, f = 1kHz — 75 — dB
VOUT ≥ 1.8V, IOUT = 30mA
Output Noise Voltage (Notes 8 & 9) BW = 10Hz to 100kHz, IOUT = 30mA — 60 — µVrms

VOUT ≤ 1.2V — 0.46 0.70

1.2V < VOUT ≤ 1.4V — 0.39 0.58

1.4V < VOUT ≤ 1.7V — 0.35 0.44

Dropout Voltage (Note 5) IOUT = 300mA 1.7V < VOUT ≤ 2.1V — 0.30 0.39 V

2.1V < VOUT ≤ 2.5V — 0.26 0.34

2.5V < VOUT ≤ 3.0V — 0.25 0.30

3.0V < VOUT ≤ 3.6V — 0.22 0.29

Output Voltage Temperature Coefficient IOUT = 30mA, TA = -40°C to +85°C — ±30 — ppm/°C

Thermal Shutdown Threshold (TSHDN) — — +150 — °C

Thermal Shutdown Hysteresis (THYS) — — +20 — °C

EN Input Low Voltage — 0 — 0.5 V

EN Input High Voltage — 1.3 — 5.25 V

EN Input Leakage VEN = 0V, VIN = 5.0V or VEN = 5.0V, VIN = 0V -1.0 — 1.0 µA
On Resistance of N-channel for Auto- VIN = 4.0V, VEN = 0V
D Version, Chanel 1 & 2 — 30 — Ω
discharge (Note 10) (Disabled)
Notes: 5. Dropout voltage is the voltage difference between the input and the output at which the output voltage drops 2% below its nominal value.
6. Quiescent current is defined here is the difference in current between the input and the output.
7. Short circuit current is measured with VOUT pulled to GND.
8. This specification is guaranteed by design.
9. To make sure lowest environment noise minimizes the influence on noise measurement.
10. AP7345D has 2 options for output, built-in discharge and non-discharge.
11. Potential multiple grades based on following output voltage accuracy.

AP7345D 4 of 15 December 2018

Document number: DS41528 Rev. 1 - 2 [Link] © Diodes Incorporated
 AP7345D

Performance Characteristics
NEW PRODUCT

AP7345D 5 of 15 December 2018

Document number: DS41528 Rev. 1 - 2 [Link] © Diodes Incorporated
 AP7345D

Performance Characteristics (Cont.)

NEW PRODUCT

°C °C
°C °C
°C °C

°C °C
°C °C
°C °C

AP7345D 6 of 15 December 2018

Document number: DS41528 Rev. 1 - 2 [Link] © Diodes Incorporated
 AP7345D

Performance Characteristics (Cont.)

NEW PRODUCT

AP7345D 7 of 15 December 2018

Document number: DS41528 Rev. 1 - 2 [Link] © Diodes Incorporated
 AP7345D

Performance Characteristics (Cont.)

Line Transient Response Line Transient Response

VIN=4.3V to 5.3V (1V/div)

tR=tF=5µs
IOUT=1mA
NEW PRODUCT

COUT=1µF VIN=2.8V to 3.8V (1V/div)

tR=tF=5µs
IOUT= 1mA
COUT=1µF

VOUT=3.3V (10mV/div) VOUT=1.8V (10mV/div)

Time (10µs/div) Time (10µs/div)

Load Transient Response Load Transient Response

IOUT= 50mA to 100mA (50mA/div)

IOUT= 50mA to 300mA (200mA/div)

VOUT=3.3V (50mV/div)
VOUT=3.3V (50mV/div)

VOUT=1.8V (50mV/div) VOUT=1.8V (50mV/div)

Time (40µs/div) Time (40µs/div)

Load Transient Response Load Transient Response

IOUT= 50mA to 100mA (50mA/div)

IOUT= 50mA to 300mA (200mA/div)

VOUT=1.8V (50mV/div) VOUT=1.8V (50mV/div)

VOUT=3.3V (50mV/div) VOUT=3.3V (50mV/div)

Time (40µs/div) Time (40µs/div)

AP7345D 8 of 15 December 2018

Document number: DS41528 Rev. 1 - 2 [Link] © Diodes Incorporated
 AP7345D

Performance Characteristics (Cont.)

Turn on Waveform, VOUT=3.3V Turn on Waveform, VOUT=1.8V

EN Input Voltage
EN Input Voltage
NEW PRODUCT

Output Voltage IOUT=1mA Output Voltage IOUT=1mA

IOUT=300mA IOUT=300mA

Time (20µs/div) Time (20µs/div)

Turn off Waveform, VOUT=3.3V Turn off Waveform, VOUT=1.8V

EN Input Voltage
EN Input Voltage

IOUT=1mA IOUT=1mA
Output Voltage IOUT=300mA Output Voltage IOUT=300mA

Time (20µs/div) Time (20µs/div)

AP7345D 9 of 15 December 2018

Document number: DS41528 Rev. 1 - 2 [Link] © Diodes Incorporated
 AP7345D

Application Information
Output Capacitor
An output capacitor (COUT) is needed to improve transient response and maintain stability. The AP7345D is stable with very small ceramic output
capacitors. The ESR (Equivalent Series Resistance) and capacitance drives the selection. If the application has large load variations, it is
recommended to utilize low-ESR bulk capacitors. It is recommended to place ceramic capacitors as close as possible to the load and the GND pins
and care should be taken to reduce the impedance in the layout.

Input Capacitor
To prevent the input voltage from dropping during load steps, it is recommended to utilize an input capacitor (CIN). A minimum 1μF ceramic
capacitor is recommended between VIN and GND pins to decouple input power supply glitch. This input capacitor must be located as close as
NEW PRODUCT

possible to the device to assure input stability and reduce noise. For PCB layout, a wide copper trace is required for both VIN and GND pins.

Enable Control
The AP7345D is turned on by setting the EN pins high, and is turned off by pulling it low. If this feature is not used, the EN pins should be tied to VIN
pins to keep the regulator output on at all time. To ensure proper operation, the signal source used to drive the EN pins must be able to swing
above and below the specified turn-on/off voltage thresholds listed in the Electrical Characteristics section.

Short Circuit Protection

When VOUT pins are short-circuit to GND, short circuit protection will be triggered and clamp the output current to approximately 60mA. This feature
protects the regulator from over-current and damage due to overheating.

Layout Considerations
For good ground loop and stability, the input and output capacitors should be located close to the input, output, and GND pins of the device. The
regulator GND pins should be connected to the external circuit ground to reduce voltage drop caused by trace impedance. Ground plane is
generally used to reduce trace impedance. Wide trace should be used for large current paths from V IN to VOUT, and load circuit.

ESR vs. Output Current

Ceramic type output capacitor is recommended for this series; however, the other output capacitors with low ESR also can be used. The relations
between IOUT (Output Current) and ESR of an output capacitor are shown below. The stable region is marked as the hatched area in the graph.

Measurement conditions: Frequency Band: 10Hz to 2MHz, Temperature: -40°C to +85°C.

AP7345D 10 of 15 December 2018

Document number: DS41528 Rev. 1 - 2 [Link] © Diodes Incorporated
 AP7345D

Ordering Information

AP7345D X X X - X

Output Discharge CH1 Output Voltage CH2 Output Voltage Package Packing

D : Output Discharge 12 : 1.2V 12 : 1.2V RH4 : X2-DFN1612-8 7 : Tape & Reel

15 : 1.5V 15 : 1.5V
18 : 1.8V 18 : 1.8V
NEW PRODUCT

25 : 2.5V 25 : 2.5V
28 : 2.8V 28 : 2.8V
285 : 2.85V 285 : 2.85V
30 : 3.0V 30 : 3.0V
33 : 3.3V 33 : 3.3V
36 : 3.6V

7” Tape and Reel

Part Number Package
Packaging
Code Quantity Part Number Suffix

AP7345D-XXXX(XX)RH4-7 RH4 X2-DFN1612-8 5000/Tape & Reel -7

Marking Information
(1) X2-DFN1612-8

(Top View)
XXX : Identification Code
XXX Y : Year : 0~9
YWX W : Week : A~Z : 1~26 week;
a~z : 27~52 week; z represents
52 and 53 week
X : Internal code

Part Number VOUT1/VOUT2 Package Identification Code

AP7345D-1218RH4-7 1.2V/1.8V X2-DFN1612-8 FAA

AP7345D-1528RH4-7 1.5V/2.8V X2-DFN1612-8 FAB

AP7345D-1812RH4-7 1.8V/1.2V X2-DFN1612-8 FAC

AP7345D-1815RH4-7 1.8V/1.5V X2-DFN1612-8 FAD

AP7345D-1818RH4-7 1.8V/1.8V X2-DFN1612-8 FAE

AP7345D-1828RH4-7 1.8V/2.8V X2-DFN1612-8 FAF

AP7345D-1833RH4-7 1.8V/3.3V X2-DFN1612-8 FAG

AP7345D-2518RH4-7 2.5V/1.8V X2-DFN1612-8 FAH

AP7345D 11 of 15 December 2018

Document number: DS41528 Rev. 1 - 2 [Link] © Diodes Incorporated
 AP7345D

Marking Information (Cont.)

Part Number VOUT1/VOUT2 Package Identification Code

AP7345D-2812RH4-7 2.8V/1.2V X2-DFN1612-8 FAJ

AP7345D-2818RH4-7 2.8V/1.8V X2-DFN1612-8 FAK

AP7345D-2825RH4-7 2.8V/2.5V X2-DFN1612-8 FAM

AP7345D-2833RH4-7 2.8V/3.3V X2-DFN1612-8 FAN

NEW PRODUCT

AP7345D-2828RH4-7 2.8V/2.8V X2-DFN1612-8 FAP

AP7345D-285285RH4-7 2.85V/2.85V X2-DFN1612-8 FAR

AP7345D-3018RH4-7 3.0V/1.8V X2-DFN1612-8 FAS

AP7345D-3028RH4-7 3.0V/2.8V X2-DFN1612-8 FAT

AP7345D-3030RH4-7 3.0V/3.0V X2-DFN1612-8 FAU

AP7345D-3318RH4-7 3.3V/1.8V X2-DFN1612-8 FAV

AP7345D-3328RH4-7 3.3V/2.8V X2-DFN1612-8 FAW

AP7345D-3330RH4-7 3.3V/3.0V X2-DFN1612-8 FAX

AP7345D-3333RH4-7 3.3V/3.3V X2-DFN1612-8 FAY

AP7345D-3612RH4-7 3.6V/1.2V X2-DFN1612-8 FAZ

AP7345D 12 of 15 December 2018

Document number: DS41528 Rev. 1 - 2 [Link] © Diodes Incorporated
 AP7345D

Package Outline Dimensions

Please see [Link] for the latest version.

X2-DFN1612-8

A1 X2-DFN1612-8
A Dim Min Max Typ
Seating Plane
A –– 0.40 0.39
NEW PRODUCT

D
A1 0.00 0.05 0.02
b 0.13 0.23 0.18
D2 D 1.55 1.65 1.60
D2 1.25 1.35 1.30
E 1.15 1.25 1.20
E2 0.25 0.35 0.30
E E2 L e –– –– 0.40
C0.15 L 0.15 0.25 0.20
z –– –– 0.11
z1 –– –– 0.05
z
z1 All Dimensions in mm
e b

Suggested Pad Layout

Please see [Link] for the latest version.

X2-DFN1612-8

X2
C Value
Dimensions
(in mm)
C 0.400
X 0.230
Y1 X1 1.300
X1 X2 1.430
Y2 Y 0.400
Y1 0.300
Y Y2 1.400

AP7345D 13 of 15 December 2018

Document number: DS41528 Rev. 1 - 2 [Link] © Diodes Incorporated
 AP7345D

Tape Orientation

XXX
XXX
XXX
NEW PRODUCT

Note: The taping orientation of the other package type can be found on our website at [Link]

AP7345D 14 of 15 December 2018

Document number: DS41528 Rev. 1 - 2 [Link] © Diodes Incorporated
 AP7345D

IMPORTANT NOTICE

DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
(AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION).

Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes
without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the
application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or
trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume
all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated
website, harmless against all damages.
NEW PRODUCT

Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel.
Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and
hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or
indirectly, any claim of personal injury or death associated with such unintended or unauthorized application.

Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings
noted herein may also be covered by one or more United States, international or foreign trademarks.

This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the
final and determinative format released by Diodes Incorporated.

LIFE SUPPORT

Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express
written approval of the Chief Executive Officer of Diodes Incorporated. As used herein:

A. Life support devices or systems are devices or systems which:

1. are intended to implant into the body, or

2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the
labeling can be reasonably expected to result in significant injury to the user.

B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the
failure of the life support device or to affect its safety or effectiveness.

Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any
use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related
information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its
representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems.

Copyright © 2018, Diodes Incorporated

[Link]

AP7345D 15 of 15 December 2018

Document number: DS41528 Rev. 1 - 2 [Link] © Diodes Incorporated