Opel Airbag Reset Tool user manual
Opel Airbag Reseter
After the car crashed and the airbag had been deployed, Opel airbag sensor will always stay
locked (Control unit faulty or deployed) and must be replaced. Even after a small accident Airbag
sensor will write into its internal memory an error message "crash data stored" or “computer
fault" and after that you need to replace this expensive sensor to a new one. With our Opel
Airbag Reset Tool you can reset and repair the airbag computer in your workshop in 1 minute. No
need to remove airbag sensor from the car.
How to operate the Opel Airbag Reseter:
Connect this tool to Opel OBD II connector (for cars from year 1996-2002). RED button is for airbag
"crash data" [Link] this button once and wait: Yellow light start to flash and after 15 second green
light inform you that "crash data" is erased. Red light set ON if erasing is not successful. Yellow button is
for erase airbag "fault memory" or "errors". If airbag warning lamp go OFF and immediately ON - evaluate
airbag "error memory" using other equipments and repair according error code.
When apply the +12V power supply to Opel airbag reseter ,the yellow light will flash
10 times. This indicates the system is self checking .After this, it will goes back to normal operation.
Opel Airbag Reset Tool has incorporated a fully automatic airbag sensor type recognition.
It works without additional computer and through the car OBD II connector, it can erase airbag
sensor "crash data" or only fault memory.
Opel Airbag Reset Tool user manual
This program works only with Opel Airbag Reset Tool hardware. Connect Opel Airbag Reset
Tool to car OBDII connector, select car year and type and type read fault codes. Works only
with original COM port.
Works with these cars:
Older Opel cars to year 1997 with pink color 26-pin connector:
- Omega, Vectra, Corsa, Astra, Tigra and others.
Opel Airbag Reset Tool user manual
You can connect this sensor on the table and erase crash data using our Opel Airbag Tool.
Use the following wiring connection:
Airbag sensor: K-line = pin 3+4, GND = pin 10, +12V = pin 7
Opel Airbag Reset Tool: K-line = pin 7 GND = pin 4+5, +12V = pin 16
Apply +12V power supply and push RED or YELLOW button on the Opel Airbag Tool.
Opel Airbag Reset Tool user manual
You can connect this sensor on the table and erase crash data using our Opel Airbag Tool.
Use the following wiring connection:
Airbag sensor: K-line = pin 5 (connected with car OBDII connector pin 12), GND = pin 6,
+12V =pin 8, airbag lamp = pin 9;
Opel Airbag Reset Tool: K-line = pin 12, GND = pin 4+5, +12V = pin 16
Apply +12V power supply and push RED or YELLOW button on the Opel Airbag Tool.
Opel Airbag Reset Tool user manual
You can connect this sensor on the table and erase crash data using our Opel Airbag Tool.
Use the following wiring connection:
Airbag sensor: K-line = pin 12 (connected with car OBDII connector pin 12), GND = pin 7,
+12V= pin 5, airbag lamp = pin 6;
Opel Airbag Reset Tool: K-line = pin 12, GND = pin 4+5, +12V = pin 16
Apply +12V power supply and push RED or YELLOW button on the Opel Airbag Tool.
Opel Airbag Reset Tool user manual
Opel cars (Zafira, Astra G) 1998-2000 airbag sensor with green or dark-blue 45-pin
connector.
You can connect this sensor on the table and erase crash data using our Opel Airbag Tool.
Use the following wiring connection:
Airbag sensor: K-line = pin 37 (connected with car OBDII connector pin 12), GND = pin 7,
+12V= pin 35, airbag lamp = pin 6;
Opel Airbag Reset Tool: K-line = pin 12, GND = pin 4+5, +12V = pin 16
Apply +12V power supply and push RED or YELLOW button on the Opel Airbag Tool.
Agila 2001 airbag sensor.
You can connect this sensor on the table and erase crash data using our Opel Airbag Tool.
Opel Airbag Reset Tool user manual
Use the following wiring connection:
Airbag sensor: K-line = pin 37 (connected with car OBDII connector pin 12), GND = pin 6,
+12V= pin 9, airbag lamp = pin 7;
Opel Airbag Reset Tool: K-line = pin 12 or 7, GND = pin 4+5, +12V = pin 16
Apply +12V power supply and push RED or YELLOW button on the Opel Airbag Tool.
Using these pictures you can erase airbag “on the table” – you must connect GND, +12V, and
Diagnostic line between airbag sensor and Opel Airbag Eraser, connect power supply to GND
and +12V and use Eraser like in the car.
OBDII Female (vehicle side) connector pinouts:
