Technical SPIKEFAST® ET-75
Data Sheet Wood Tie Plugging Material
DESCRIPTION
SPIKEFAST® ET-75 is specifically designed to remediate wood ties. This non-foaming, 100% solid polyurethane is specifically
designed to efficiently anchor spikes with comparable strength to that of un-spiked hardwood ties. SPIKEFAST® ET-75 is
dispensed from equipment specifically engineered for efficient metering/mixing, presssure and temperature control, and
operation under wide range of outdoor conditions.
WHERE TO USE PACKAGING COLOR
• Wood crossties spike holes–re-spike filled holes 200 gallons (758 L), 50 gallons (190 L) White or
• Tie remediation–bonds tightly to wood & seals out water 5 gallons (19 L), 15 oz. Cartridge (450 ml) Yellow
• Tie defects–penetrates cracks, voids, crevises YIELD
150 spike holes (0.63 in. x 0.63 in. x 4 in.) per gallon.
Willamette Valley Company 38 spike holes (1.6 cm x 1.6 cm x 10.2 cm) per liter.
FEATURES AND BENEFITS
[Link] • Quick Cure Time–high production rates SHELF LIFE
• Dynamic Rail Roll-Over–equal to hardwood, 2X wood plugs 6 months in containers and 12 months for cartridges
800.333.9826 when properly stored.
• Lateral Resistance–20% greater than hardwood ties
• Easy to Apply–minimal maintenance and clean up STORAGE
Store in original container and sealed until ready for use.
Reseal used containers and store in an upright position.
Partnering through service,
TECHNICAL INFORMATION
innovation, and integrity
Typical Properties
VOC, lbs/gal (g/L), ASTM D 2369 0
Viscosity, cps, ASTM D 4878, 77°F (25°C), Iso / Resin 200 / 5000
Hardness, Shore D, ASTM D 2240 80
WVCO Railroad Division
[Link] Set time, sec, 77°F (25°C) 25 / 60—Cartridges (Temperature dependent)
Service temperature, ° F (° C) -40 to 212 (-40 to 100)
Process Parameters
SALES DESK Ratio by volume, Resin to Iso 2 to 1
1-800-333-9826
Meter equipment Plural component
sales@[Link]
Static mixer 13-32
PRODUCT SUPPORT
Michael R. Land Equipment pressure, psi (MPa) 400 - 600 (2.3 – 4.1)
541.484.9621
Equipment temperature, ° F (° C) 70 to 125 (21 to 52)
03mikel@[Link]
Recommended application volume, in3 (cm3) 2 in3 (32.5 cm3)
WILLAMETTE VALLEY COMPANY
APPLICATION [Link]
Use Willamette Valley Company’s metering equipment which is Proper application is the responsibility of the user. Field visits by info@[Link]
specifically engineered for processing SPIKEFAST® ET-75 to WVCO Representatives are for the purpose of making technical
generate the proper mix ratio, pressure, and temperature. recommendations and equipment service only, and not for DIVISIONS
supervising or providing quality control.
SPIKEFAST® ET-75 is supplied in a ready-to-use form that WESTERN DIVISION
requires proper mixing and dispensing. Care should be taken that Contact a Willamette Valley Company Representative for more 1075 Arrowsmith Street
SPIKEFAST® ET-75 is stored properly, does not become information on product and equipment instructions, PO Box 2280
contaminated with foreign matter, and is applied according to recommendations, and full-service warranty. Eugene, OR 97402
WVCO recommendations. Tel 541.484.9621
[Link]
[Link]
HEALTH AND SAFETY
Before handling, you should become familiar with the Material Safety Data Sheet (MSDS) regarding the risks and safe use of this EASTERN DIVISION
product. To obtain an MSDS please call 800-333-9826 or send an email to: msds@[Link]. 6662 Marbut Road
. Lithonia, GA 30058
Tel 888.878.9826
MIDWEST DIVISION
1549 Hwy 2
Two Harbors, MN 55616
Tel 218.834.3922
PRECISION TECHNOLOGIES DIVISION
675 McKinley Street
Eugene, OR 97402
Tel 541.484.2368
[Link]
SOUTHERN DIVISION
100 Dixie Mae Drive
PO Box 4450
Pineville, Louisiana 71361
Tel 318.640.5077
SUBSIDIARIES
CANADIAN WILLAMETTE
325 Edworthy Way
New Westminster BC V3L 5G4
Tel. 800.663.4298
ECLECTIC PRODUCTS INC.
Corporate Office
1075 Arrowsmith Street
Eugene, OR 97402
Tel 541.284.4667
[Link]
IDAHO MILL & GRAIN
445 North 430 West Hwy
Po Box188
Malad City, Idaho 83252
Tel 208.766.2206
TAPEL WILLAMETTE LTD. S.A.
Av. Estero La Posada 3625 Parque
Industrial Coronel Coronel, Chile
Tel [Link].100
[Link]
DISCLAIMER OF WARRANTY
TEST RESULTS ARE TO BE CONSIDERED AS REPRESENTATIVE OF CURRENT PRODUCTION AND SHOULD NOT BE TREATED AS SPECIFICATIONS. WHILE ALL THE INFORMATION PRESENTED IN THIS
DOCUMENT IS BELIEVED TO BE RELIABLE AND TO REPRESENT THE BEST AVAILABLE DATA ON THESE PRODUCTS, NO GUARANTEE, WARRANTY, OR REPRESENTATION IS MADE, INTENDED, OR
IMPLIED AS TO THE CORRECTNESS OR SUFFICIENCY OF ANY INFORMATION, OR AS TO THE SUITABILITY OF ANY CHEMICAL COMPOUNDS FOR ANY PARTICULAR USE, OR THAT ANY CHEMICAL
COMPOUNDS OR USE THEREOF ARE NOT SUBJECT TO A CLAIM BY A THIRD PARTY FOR INFRINGEMENT OF ANY PATENT OR OTHER INTELLECTUAL PROPERTY RIGHT. EACH USER SHOULD
CONDUCT A SUFFICIENT INVESTIGATION TO ESTABLISH THE SUITABILITY OF ANY PRODUCT FOR ITS INTENDED USE.
PROPER APPLICATION IS THE RESPONSILBITY OF THE USER. AS WITH ANY PRODUCT THE USE OF THE THIS PRODUCT IN A GIVEN APPLICATION MUST BE TESTED (INCLUDING BUT NOT LIMITED Revision Date May 2012
TO FIELD TESTING) IN ADVANCE BY THE USER TO DETERMINE SUITIBILITY. TESTING IS THE REQUIREMENT OF BOTH ENGINEERS AND CONTRACTORS ALIKE. WVCO DOES NOT WARRANT THE
APPLICATION UNDER ANY OR ALL CIRCUMSTANCES.
