For More Study Materials at Examdays.
com/railwayrecruitment
Engineering Drawing MCQ
Introduction to Engineering Drawing
1 Which tool can be used to draw a 90 degree angle?
A) 30/60 triangle B) Protractor C) Drafting machine D) All of the above
2 Which set of lead grades has a grade out of sequence?
A) H, HB, B, 3B B) 7B, H, F, 3H C) 6B, B, H, 4H D) 9H, HB, B, 2B
3 Which type of line is part of a dimension?
A) Break lines B) Phantom lines C) Extension lines D) Cutting plane lines
4 Which type of line is particular to section drawings?
A) Break lines B) Phantom lines C) Extension lines D) Cutting plane lines
5 Which angle cannot be made with either a 45 or 30/60 triangle or a combination of the two?
A) 90 B) 70 C) 30 D) 15
6 A drawing instrument set usually contains all of the following, except:
A) Bow compass B) Scale C) Dividers D) Extra leads
7 Which line type is thin and light?
A) Visible lines B) Center lines C) Construction lines D) All of the above
8 Which line type is thick and black?
A) Visible lines B) Center lines C) Construction lines D) All of the above
9 Which type of line has precedence over all other types of lines?
A) A hidden line B) A center line C) A visible line D) None of the above
10 Which statement(s) is true about the precedence of lines?
A) A hidden line has B) A center line has C) A visible line has D) All of the above
precedence over a precedence over a precedence over a
center line visible line miter line
11 When you want to make the letters of a line of text narrower, you would set its:
A) Aspect B) Scale C) Alignment D) Font
For More Study Materials at Examdays.com/railwayrecruitment
1
For More Study Materials at Examdays.com/railwayrecruitment
12 When you want to make sure that all of the text stays to the right of a given point on the
drawing, you wound set its:
A) Aspect B) Scale C) Alignment D) Font
13 The primary unit of measurement for engineering drawings and design in the mechanical
industries is the
A) Millimeter B) Centimeter C) Meter D) Kilometer
14 A French curve is used to draw
A) Circle B) Ellipse C) Smooth free form D) Polygon
c ur v e
ANSWER
1 D 4 D 7 C 10 A
2 B 5 B 8 A 11 A
3 C 6 D 9 C 12 C
13 A 14 C
For More Study Materials at Examdays.com/railwayrecruitment
2
For More Study Materials at Examdays.com/railwayrecruitment
ENGINEERING DRAWING SCALE
1 Which one of the following is not a reduction scale?
A) 1:1 B) 1:200 C) 5/320 D) 5:6
2 For drawing of small instruments, watches etc. the scale used is
A) Reduced scale B) Full scale C) Enlarged scale D) None of these
3 When the drawing are drawn smaller than the actual size of object then scale is known as
A) Reduced scale B) Enlarged scale C) Full scale D) None of these
4 If the 10m length is represented as 1 mm on the map then representative fraction is
8 A map of 10 cm X 8 cm represents an area of 50000sq. meter of a field. The R.F. of the
scale is
5
A) 1/25 B) 1/625 C) 1/2500 D) 1/6250000
6 A) 1/100 B) 1/1000 C) 1/10 D) None of these
The R.F. of scale is always
7 A) Less than 1 B) Equal to 1 C) Greater than 1 D) Any of these
The unit of R.F. is
A) Cubic centimeter B) Square centimeter C) Centimeter D) None of these
The full form of R.F. is
9 An area of 36 square kilometer is represented by 144 square centimeter on a map. What is
A) Reducing fraction B) Representative C) Reduction factor D) Representative
t
h fraction factor
e
R.F. ?
A) 1/4 B) 1/2 C) 1/5000 D) 1/50000
10 When measurements are required in three consecutive units, the appropriated scale is
A) Plain scale B) Diagonal scale C) Isometric scale D) Scale of cords
11 In the diagonal scale, the word “diagonal” is used because it is most suitable for the
measurement of
A) Diameter of a B) Diagonal of a C) Side of a pentagon D) All of these
Circle Square
For More Study Materials at Examdays.com/railwayrecruitment
3
For More Study Materials at Examdays.com/railwayrecruitment
12 For scale, which one is not correct
(a) 1:2 (b) 1:20 (c) 1:1/2 (d) 1/2
ANSWER KEYS:
1 A 2 A 3 A 4 D
5 D 6 D 7 B 8 C
9 D 10 B 11 D 12 D
Engineering Drawing Curve
1 What type of curve is created by the intersection of a plane parallel to the side of cone?
A) parabola B) hyperbola C) ellipse D) roulette
2 What type of curve is created by the intersection of a plane with a cone which makes an
angle with the axis greater than the angle between the side of the cone and the axis?
A) parabola B) hyperbola C) ellipse D) roulette
3 A(n)________ is created by the motion of a point on a circle as the circle rolled along a
straight line.
A) epicycloid B) hyperbola C) cycloid D) spiral
4 A circle will appear on an isometric drawing as a(n) .
A) ellipse B) cycloid C) circle D) parabola
5 The curve generated by a point on the circumference of a circle, which rolls without slipping
along outside of another circle is known as
A) Hypocycloid B) Epicycloid C) Cycloid D) Trochoid
6 In the game of cricket, a ball is thrown from the boundary and reaches the gloves of the
wicket keeper, the curve traced out will be
A) Hyperbola B) Involute C) Parabola D) Cycloid
For More Study Materials at Examdays.com/railwayrecruitment
5
For More Study Materials at Examdays.com/railwayrecruitment
7 A curved traced out by a point which moves uniformly both about the centre and at the same
time away or towards the centre is known as
A) Involute B) Archemedian C) Cycloid D) None of above
spiral
8 The eccentricity of which of the following curve is greater than one?
A) Ellipse B) Parabola C) Hyperbola D) None of above
ANSWER
1 A 2 B 3 C 4 A
5 B 6 C 7 B 8 C
Projections of Point & LINE
1 The Intersection of a plane surface with the horizontal plane is a line and is
call ________________
A) Horizontal Trace B) Vertical Trace C) Profile Trace D) Trace
2 The Intersection of a plane surface with the Vertical plane is aline and is call ___________
A) Horizontal Trace B) Vertical Trace C) Profile Trace D) Trace
3 The intersection of a plane surface with the profile plane is line and is call _________
A) Horizontal Trace B) Vertical Trace C) Profile Trace D) Trace
4 If a line is inclined to H.P., its plan will .
A) be perpendicular B) be parallel to XY C) show the true D) None of the above
to XY line line length
5 _______________ number Traces Produced if Required Will Meet On xy Line.
A) 1 B) 2 C) 3 D) 4
For More Study Materials at Examdays.com/railwayrecruitment
6
For More Study Materials at Examdays.com/railwayrecruitment
6 Straight Line of projection Will Make an angle with xy Line to the angle of plane with other
principal plane.
A) Perpendicular B) Equal C) Right angle D) Zero
7 When a point is above H.P. and behind V.P., the point is resting in which quadrant?
A) 1st B) 2nd C) 3rd D) 4th
8 When a point is above H.P. and in front of V.P., the point is resting in which quadrant?
A) 1st B) 2nd C) 3rd D) 4th
9 When a point is below H.P. and in front of V.P., the point is resting in which quadrant?
A) 1st B) 2nd C) 3rd D) 4th
10 When a point is below H.P. and behind V.P., the point is resting in which quadrant?
A) 1st B) 2nd C) 3rd D) 4th
11 If a line is parallel to H.P., its front will be ______ to XY line.
A) Perpendicular B) Parallel C) Inclined D) None of the above
For More Study Materials at Examdays.com/railwayrecruitment
For More Study Materials at Examdays.com/railwayrecruitment
12 If a line is parallel to V.P., its top view will be_____to XY line.
A) Perpendicular B) Parallel C) Inclined D) None of the
above
13 If a line is inclined to V.P., its elevation will __ .
A) be perpendicular B) be parallel to XY C) show the true D) None of the
above
to XY line line length
14 If a line is inclined to the Vertical Plane and parallel to Horizontal Plane, then which of the
following statements is always CORRECT?
A) True Length = Plan B) True Length ≠ Plan C) True Length > D) True Length =
Length Length Elevation Length Elevation Length
15 When a line is inclined to VP and parallel to HP, the front view will be _ to xy.
A) parallel B) perpendicular C) inclined at angle φ D) non on these
16 When the front view of line having a length less than the original length then which of the
following is correct?
A) Line is inclined to B) Line is inclined to C) Line is inclined to D) (B) and (C) both
H.P. both H.P. and V.P. V.P.
ANSWER
1 A 2 B 3 C 4 B
5 B 6 B 7 B 8 A
9 D 10 C 11 B 12 B
13 B 14 A 15 A 16 D
For More Study Materials at Examdays.com/railwayrecruitment
7
For More Study Materials at Examdays.com/railwayrecruitment
Projections of Plane
1 When a plane is parallel to H.P and perpendicular to V.P and P.P always __________ first
A) T.V. B) S.V. C) B.V. D) F.V
2 A Plane surface has
___________ Dimension.
A) 0 B) 1 C) 2 D) 3
3 Three Dimensional Drawing of the plane in the given position, We can visualize that
Elevation will be _________ of the same size.
A) Plane B) Circular Plane C) straight line D) None of this
4 Plane is perpendicular to one of the principal planes the projection on that plane will
be ________________
A) Line B) Straight line C) Curve D) Perpendicular line
5 Projection of plane in two other planes due to inclination will not show
______________ shape.
A) Inclination B) Plane C) Line D) TRUE
6 Trace on other Principal Plane will be_____________ Line to xy
Line.
A) Perpendicular line B) Projection of line C) Perpendicular D) a,b both
Plane
7 When a plane is parallel to V.P and perpendicular to H.P and P.P always __________ first
A) T.V. B) S.V. C) B.V. D) F.V
8 A viewing direction which is perpendicular to the surface in question gives a(n)
___________ view.
A) inclined B) normal C) oblique D) perspective
9 A viewing direction which is parallel to the surface in question gives a(n) _________ view.
A) inclined B) normal C) edge D) perspective
For More Study Materials at Examdays.com/railwayrecruitment
8
For More Study Materials at Examdays.com/railwayrecruitment
10 When a surface of an object is inclined to a plane of projection, it will appear
in the view.
A) foreshortened B) in true size and C) as a line D) as a point
shape
11 Depending on its relationship to the projection plane on which the view is projected, a line
may project:
A) true length B) foreshortened C) as a point D) all of the above
12 If a surface on an object is parallel to one of the principal planes of projection, then the
angular relationship of that surface to at least two other principal projection planes is:
A) parallel B) perpendicular C) inclined D) unknown
13 Straight Line of projection Will Make an angle with xy Line to the angle of plane with other
principal plane.
A) Perpendicular B) Equal C) Right angle D) Zero
14 The Intersection of a plane surface with the horizontal plane is a line and is
call ________________
A) Horizontal Trace B) Vertical Trace C) Profile Trace D) Trace
15 The Intersection of a plane surface with the Vertical plane is a line and is call _________
A) Horizontal Trace B) Vertical Trace C) Profile Trace D) Trace
16 The intersection of a plane surface with the profile plane is line and is call ________
A) Horizontal Trace B) Vertical Trace C) Profile Trace D) Trace
17 When a plane is parallel to H.P and perpendicular to V.P and P.P always __________ first
A) T.V. B) S.V. C) B.V. D) F.V.
18 When a plane is parallel to V.P and perpendicular to H.P and P.P always __________ frist
A) T.V. B) S.V. C) B.V. D) F.V.
19 A square plate of negligible thickness is inclined to HP. The front view will appear as
For More Study Materials at Examdays.com/railwayrecruitment
9
For More Study Materials at Examdays.com/railwayrecruitment
A) Rhombus B) Square C) Line D) Rectangle
ANSWER
1 A 2 C 3 A 4 B
5 D 6 A 7 B 8 B
9 C 10 A 11 D 12 B
13 B 14 A 15 B 16 C
17 A 18 D 19 A
For More Study Materials at Examdays.com/railwayrecruitment
10
For More Study Materials at Examdays.com/railwayrecruitment
Projections & Sections of Solid
1 This type of solid has two bases that are parallel equal polygons:
A) pyramid B) prism C) cone D) torus
2 The solid having a polygon for a base and triangular lateral faces intersecting at a vertex is
A) pyramid B) prism C) cone D) torus
3 Among the following solids, a regular polyhedron is
A) square prism B) square pyramid C) cube D) sphere
4 A solid having minimum number of faces is
A) tetrahedron B) triangular prism C) square pyramid D) cube
5 The number of face in a dodecahedron are
A) 4 B) 8 C) 12 D) 20
6 The number of stages that are necessary to get the orthographic views of a solid having its
axis inclined to both reference planes is
A) 1 B) 2 C) 3 D) 4
7 A tetrahedron is resting on its face on the H.P. with a side perpendicular to the V.P. Its front
view will be
A) equilateral B) isosceles triangle C) scalene triangle D) right-angle
triangle triangle
8 A square pyramid is resting on a face in the V.P. The number of dotted lines which will
appear in the front view is
A) 1 B) 2 C) 3 D) 4
9 The solid, which will have two dotted lines in the top view when it is resting on its face in the
H.P. is
A) square pyramid B) pentagonal C) hexagonal D) all of these
pyramid pyramid
10 A cube is resting on the H.P. with a solid diagonal perpendicular to it. The top view will
appear as
For More Study Materials at Examdays.com/railwayrecruitment
11
For More Study Materials at Examdays.com/railwayrecruitment
A) square B) rectangle C) irregular hexagon D) regular hexagon
11 A right-circular cone resting on a point of its base circle in the H.P. has the axis inclined at 30º
to the H.P. and 45º to the V.P. The angle between the reference line and top view of the
axis will be
A) 30º B) between 30º and C) 45º D) more than 45º
45º
12 A right-circular cone resting on a generator in the H.P. has the axis inclined at 30º to the H.P.
and 45º to the V.P. The angle between the reference line and top view of the axis will be
A) less than 45º B) 45º C) more than 45º D) any of these
13 A cylinder rests on a point of its base circle in the H.P., having the axis inclined at 30º to the
H.P. and 60º to the V.P. The inclination of the top view of the axis with the reference line
will be
A) 30º B) 60º C) 90º D) none of these
14 A cutting plane cut the cone such a way that true shape of cutting portion is seen as triangle
when cutting plane is cut the base and passed through_________
A) midpoint of axis B) apex of cone C) generator of cone D) any point on axis
15 Another name for a cube is a
A) hexahedron B) tetrahedron C) isocohedron D) octahedron
16 Another name for a tetrahedron is a
A) triangular prism B) square prism C) triangular pyramid D) square pyramid
17 A(n) ________ cone has two planar surfaces parallel to each other.
A) truncated B) frustum C) right D) oblique
18 The solid having a polygon for a base and triangular lateral faces intersecting at a vertex is
A) pyramid B) prism C) cone D) torus
19 Name the solid formed by four equilateral triangle
A) Square pyramid B) Triangular pyramid C) Tetrahedron D) Square prism
20 A cylinder standing on the HP is cut by a vertical plane parallel to the axis and away from it.
For More Study Materials at Examdays.com/railwayrecruitment
12
For More Study Materials at Examdays.com/railwayrecruitment
The shape of the section will be
A) Rectangle B) Circle C) Ellipse D) Hyperbola
21 When the axis of the solid is parallel to both HP and VP the view which reveals the true shape
of the base is
A) Front view B) Top view C) Side view D) None of these
22 Name the solid formed by revolving right angle triangle with one of its perpendicular side
fixed
A) Cone B) Cylinder C) Tetrahedron D) Octahedron
23 When the cone, resting on base on V.P., is cut by section plane parallel to V.P. then the true
shape is _________ and can be seen in _________ view.
A) Circle, Front B) Ellipse, Front C) Ellipse, Top D) Circle, Top
24 To obtain the true shape of the section of solid, an auxiliary plane is set
A) Inclined at an B) parallel to XY C) Parallel to a D) perpendicular to a
angle of 45 to a cutting plane cutting plane
cutting plane
ANSWER
1 B 2 A 3 C 4 A
5 C 6 C 7 B 8 B
9 D 10 D 11 D 12 C
13 C 14 B 15 C 16 C
17 A 18 A 19 C 20 A
21 C 22 A 23 A 24 C
For More Study Materials at Examdays.com/railwayrecruitment
13
For More Study Materials at Examdays.com/railwayrecruitment
Orthographic Projections
1 What types of sketch are typically used in the refinement stage of the design process?
A) isometric B) document C) oblique D) ideation
2 What type of sketch incorporates
convergence?
A) isometric B) perspective C) oblique D) multi view
3 What type of sketch shows the front in true shape?
A) isometric B) perspective C) oblique D) axonometric
4 What is the major difference(s) between perspective and parallel projection?
A) Parallel B) perspective C) parallel projection D) perspective
projection can only projection gives a is equivalent to a projection can only
be used with objects more realistic perspective be used for creating
containing parallel representation of an projection where the oblique and not
edges. object viewer is standing isometric pictorials
infinitely far away
5 What type of sketch uses a miter line?
A) a two-view B) an isometric C) a three-point D) a three-view multi
multiview pictorial perspective pictorial view
6 Where do the projection lines converge in a perspective sketch?
A) the vanishing B) the ground line C) the horizon line D) the eye point
point
7 The selection of the front view in executing a multi view drawing of an object is dependent
upon the following factors:
A) Size and shape B) The number of C) The greatest D) the size of the
of the object and principal views contour shape, the object, size of the
their relationship to required and the related dashed lines, paper, position of
all views. related auxiliary and the position of use, and least
views needed to use. number of hidden
describe the object. lines
For More Study Materials at Examdays.com/railwayrecruitment
14
For More Study Materials at Examdays.com/railwayrecruitment
8 All of the following statements about multi view drawings are true,
except:
A) each view is a 3-D B) based on C) at least two views D) views are defined
pictorial image orthographic of the object by planes of
projection projection
9 Which type of projection does not have the projection rays parallel to each other?
A) axonometric B) oblique projection C) orthographic D) perspective
projection projection projection
10 Which is not a principal view?
A) bottom B) left side C) auxiliary D) front
11 Principle planes will appear as:
A) normal planes or B) oblique planes or C) normal planes or D) skewed planes or
edges edges oblique planes edges
12 In orthographic projection, visual rays or lines of sight for a given view are __________ to
each other.
A) perpendicular B) oblique C) normal D) parallel
13 What two types of projections give a pictorial view of the object without convergence?
A) orthographic and B) oblique and C) perspective and D) isometric and
perspective axonometric oblique orthographic
14 Inclined planes in a three-view drawing will appear as:
A) two surfaces and B) two edges and one C) three edges D) foreshortened in
one edge surface each view
15 Oblique planes in a three-view drawing will appear as:
A) two surfaces and B) two edges and one C) three edges D) three surfaces
one edge surface
16 Normal planes in a three-view drawing will appear as:
A) one surface and B) three surfaces C) one edge and two D) three edges
two edges surfaces
For More Study Materials at Examdays.com/railwayrecruitment
15
For More Study Materials at Examdays.com/railwayrecruitment
17 What are the three principle planes in orthographic projection?
A) front, top, profile B) back, top, profile C) top, front, right D) frontal, horizontal,
side profile
18 The top view of an object should typically be drawn:
A) to the right of the B) anywhere on the C) directly above the D) on a separate
front view. same page. front view. piece of paper.
19 A horizontal surface of a multi view drawing will appear as a(n) ________ in the front
view.
A) edge B) normal surface C) point D) foreshortened
surface
20 Which view is usually developed first, contains the least amount of hidden lines, and shows
the most contours in multi view drawings?
A) right side B) top C) back D) front
21 A sphere can be described in how many
views?
A) 4 B) 3 C) 2 D) 1
22 An asymmetric object is usually described by how many views?
A) 6 B) 3 C) 4 D) 2
23 An axially symmetric object, such as one turned on a lathe, normally can be shown in
_________ view(s).
A) one B) two C) three D) four
24 In orthographic projection, visual rays are ________ to the projection plane.
A) parallel B) adjacent C) perpendicular D) tangent
25 The top and right side views have what common dimension(s)?
A) height and width B) width and depth C) height D) depth
For More Study Materials at Examdays.com/railwayrecruitment
17
16
For More Study Materials at Examdays.com/railwayrecruitment
26 For orthographic projection, the engineering custom in the United States dictates the use of:
A) first-angle B) second-angle C) third-angle D) fourth-angle
projection projection projection projection
27 For orthographic projection, the engineering custom in Europe dictates the use of:
A) first-angle B) second-angle C) third-angle D) fourth-angle
projection projection projection projection
28 The sequence for the direction of view (or line of sight) for any orthographic projection as
utilized in the United States is:
A) eye of B) eye of C) projection D) projection
observer>projection observer>object>proj plane>object>eye of plane>eye of
plane>object ection plane observer observer>object
29 Good practice dictates that the characteristic contour shape of the object be shown in what
view?
A) top B) front C) right side D) any side
30 The height, width, and depth of an object can be shown with a minimum of how many
orthographic projection views?
A) six B) three C) two D) four
31 Which of the following pairs of orthographic views both show the height dimension?
A) left side and front B) top and front C) top and rear D) bottom and right
side
32 In the first angle projection method, the view seen from left is placed on
A) Above Front View B) Right of Front C) Above Top View D) Above Top View
View
33 Second angle projection is not used because
For More Study Materials at Examdays.com/railwayrecruitment
For More Study Materials at Examdays.com/railwayrecruitment
A) Plan is above xy B) both views overlap C) elevation is above D) views are small in
each other xy size
34 If the object lies in third quadrant, its position with respect to reference planes will be
A) In front of VP, B) Behind VP, above C) Behind VP, below D) In front of VP,
above HP HP HP below HP
35 If the object lies in the second quadrant, its position with respect to reference plane will be
A) In front of V.P. and B) Behind V.P. and C) In front of V.P. and D) Behind V.P. and
above H.P below H.P. below H.P. above H.P.
36 In a third angle projection method, right hand side view of an object is drawn ____
front view.
A) Left side of B) Right side of C) Rear side of D) None of above
37 Fourth angle projection is not used because
A) Front view is B) Top view is above C) Front view and top D) Front view and
above reference line reference line and view both overlap on top view both
and top view is front view is below each other and below overlap on each
below reference line reference line reference line other and above the
reference line
38 For the third angle projection method, Which of the following is correct?
A) Observer - Object B) Observer – Plane – C) (A) and (B) both D) None of above
– Plane Object
ANSWER
1 B 2 B 3 C 4 B, C
5 D 6 A 7 D 8 A
9 D 10 C 11 A 12 D
13 B 14 A 15 B 16 A
17 D 18 C 19 A 20 D
21 D 22 B 23 B 24 C
For More Study Materials at Examdays.com/railwayrecruitment
18
For More Study Materials at Examdays.com/railwayrecruitment
25 D 26 C 27 A 28 A
29 B 30 C 31 A 32 B
33 B 34 C 35 D 36 A
37 C 38 B 39
For More Study Materials at Examdays.com/railwayrecruitment
For More Study Materials at Examdays.com/railwayrecruitment
Isometric Projections
1 If a client of yours is having difficulty visualizing a design, what type of drawing would be the
easiest to understand?
A) axonometric B) three-view C) one-view D) bimetric
orthographic orthographic
2 Which of the following is not a pictorial drawing?
A) isometric B) multi view C) perspective D) axonometric
3 Which of the following projection methods does not use projectors perpendicular to the
projection plane?
A) isometric B) orthographic C) oblique D) axonometric
4 A circle will appear on an isometric drawing as a(n) .
A) ellipse B) cycloid C) circle D) parabola
5 An axonometric drawing which has two axes divided by equal angles
is:
A) diametric B) trimetric C) orthographic D) isometric
6 An axonometric drawing which has all three axes divided by equal
angles is:
A) diametric B) trimetric C) orthographic D) isometric
7 In a trimetric drawing, the relationship of the angle between axes to each other is:
A) three are equal B) two are equal C) three are unequal D) none of the above
8 In an isometric sketch of a cube:
A) the frontal face B) the receding axes C) all faces are D) only the depth
appears in its true are at 45 degrees to equally distorted distances must be
shape the horizontal reduced
9 In isometric drawings:
A) Two axes are B) True C) All faces are D) None of the above
perpendicular measurements can unequally distorted
be made only along
For More Study Materials at Examdays.com/railwayrecruitment
19
For More Study Materials at Examdays.com/railwayrecruitment
or parallel to the
isometric axes
10 In an axonometric drawing, the projection rays are drawn _____ to each other and
______ to the plane of projection.
A) parallel .... oblique B) oblique. ... parallel C) Parallel D) parallel. .. parallel
..perpendicular
11 One method of drawing an ellipse that represents an isometric pictorial circle is known as:
A) the box B) the coordinate C) the four-center D) the offset
construction method construction method approximation construction method
method
12 Non-isometric lines are located and sketched how?
A) They are drawn B) They are C) They are D) They are located
parallel to the measured using the measured using a by determining the
isometric axis. angle from the multi non-isometric endpoints of the
view. template. non-isometric line.
13 In an oblique sketch of a cube
A) the frontal face B) both receding axes C) all faces are D) the depth
appears in its true are at 30 degrees to equally distorted distances must be
shape the horizontal reduced
14 In an oblique drawing, all of the following angles are commonly used for drawing the depth
axis, except:
A) 30° B) 45° C) 60° D) 90°
15 In an oblique drawing, the projection rays are drawn _____ to each other and _____
to the plane of projection.
A) oblique. ... oblique B) oblique. ... parallel C) parallel. ... oblique D) parallel. .. parallel
16 A circle will appear on an isometric drawing as a(n) .
A) ellipse B) cycloid C) circle D) parabola
17 In isometric projection the three edges of an object are inclined to each other at
A) 60 B) 120 C) 30 D) 90
For More Study Materials at Examdays.com/railwayrecruitment
2 10
For More Study Materials at Examdays.com/railwayrecruitment
18 A square lamina in isometric projection appears as
A) Rhombus B) Rectangle C) Trapezium D) Parallelogram
19 In an isometric drawing, lines that are not parallel to the isometric axes are called
A) dimetric lines B) trimetric lines C) non-isometric D) multi view lines
l i ne s
20 The projection showing the front in the true shape and size is
A) isometric B) perspective C) oblique D) axonometric
21 Inclined planes in a three-view drawing will appear as
A) two surfaces and B) one surface and C) three edges D) foreshortened in
one edge two edges each view
22 This type of projection is when projectors are parallel to each other, but are at an angle
other than 90 degrees to the plane of projection:
A) perspective B) oblique C) aesthetic D) angular
23 While drawing the isometric view of the sphere, its diameter is taken as
A) Equal to actual B) 11/9 times of the C) 21/9 times of the D) none of the above
diameter actual diameter actual diameter
24 Two lines inclined at 90° in the orthographic view appear in isometric view to be inclined at
A) 60 ° B) 90 ° C) 120 ° D) 180 °
25 Length of a line „L‟ in isometric drawing or view will be
A) 0.707 L B) ) 0.815 L C) 0.866 L D) equal to length L
26 I f D is the diameter of sphere, its value in isometric projection will be equal to
A) √3⁄2 D B) √2⁄3 D C) D D) None of these
27 In isometric projection/drawing the ellipse is normally drawn by which method
A) Arc of circle B) Concentric circle C) Four centre D) Oblong method
method method method
28 The isometric view of a vertical line is represented at an angle of in front view and
For More Study Materials at Examdays.com/railwayrecruitment
For More Study Materials at Examdays.com/railwayrecruitment
having a length ________ the original length of line.
A) 30 0 , Same as B) 30 0, Less than C) 90 0, Same as D) 90 0,
Less than
29 The isometric projection of 90 mm line is ___________ mm.
A) 30*(6) (1/2) B) 30*(3) (1/2) C) 30*(2) (1/2) D) None of above
30 While drawing the isometric view of the sphere, its diameter is taken as
(a) Equal to actual (b) 11/9 times of the (c) 21/9 times of the (d) none of the
diameter actual diameter actual diameter `above
31 The isometric view of a vertical line is represented at an angle of in front view and
having a length ________ the original length of line.
(a) 30o, Same as (b) 90o, Same as (c) 30o, Less than (d) 90o, Less than
ANSWER
1 A 2 B 3 C 4 A
5 A 6 D 7 D 8 C
9 B 10 C 11 A 12 D
13 A 14 D 15 C 16 A
17 B 18 D 19 C 20 C
21 D 22 D 23 24
25 26 27 28
29 30 A
For More Study Materials at Examdays.com/railwayrecruitment
22
