NTG-1
Instruction Manual
[Link]
(EMC, LVD)
Introduction
I want to thank you for your purchase of the
NTG-1 shotgun microphone.
The design brief for this microphone was to build a
shotgun that could be used in professional video,
film and live stage applications where low noise, a
wide frequency response and tightly controlled polar
patterns are vital.
I am sure that once you have used your new microphone,
you will agree we achieved our aim.
Like all microphones, the NTG-1 is manufactured
using the finest surface mount electronic components
available, and has a body machined of high grade
aluminium which is finished in hard wearing epoxy
paint.
The heart of any microphone is the capsule, and with
the NTG-1, we have designed and incorporated what
we believe to be one of the best transducers in its
class.
The NTG-1 has many uses; It can be mounted on video
cameras using either the on-board camera mic mounts
or the optional shock mount. The NTG-1 is also suitable
as a boom mounted mic for film and video use where it
is desirable to get closer to the sound source yet still be
out of the shot. Another area where the NTG-1 excels is
in a live sound situation, used to great effect as a ‘crowd
mic’ when doing a live band recording.
The NTG-1 comes complete with a heavy duty
microphone holder and a wind cover for ‘moderate’
outdoor applications. has also designed a
series of products which include the Dead Cat wind
sock (for high wind applications) and boom pole as well
as various cables and adaptors. Details of these units
are available on the website [Link]
Also while on our website please take the time to
register your microphone for a full ten year warranty.
Peter Freedman
Microphones
Sydney, Australia
-2-
Specifications
Acoustic Line plus gradient
Principle:
Directional Super-Cardioid
Pattern: (see graph)
Frequency 20Hz ~ 20,000Hz
Range: selectable HPF@80Hz/12dB
octave (see graph)
Output 50Ω
Impedence:
Sensitivity: -36dB re 1V/Pa @ 1kHz
(15mV/Pa @ 94dB SPL)
±2dB @ 1kHz
Equivalent Noise: 18dBA SPL
(per IEC651)
Maximum +6.9dBu
Output: (@ 1kHz, 1% THD into 1kΩ)
Dynamic Range: 121dB (per IEC651)
Maximum SPL: 139dB
(@ 1kHz, 1% THD into 1kΩ)
Signal/Noise: 76dB SPL
(@ 1kHz, rel 1Pa per IEC651)
Power Phantom P48, P24
Requirement:
Output 3-pin XLR
Connection:
Net Weight: 105g
-3-
Specifications
Frequency Response
Ê £ä
Ê ä
` ÊÀiÊ£Ê6É*>
Ê £ä
Ê Óä
Ê Îä
Ê {ä
ÊÓä â Ê £ä ä Ê £äääÊ £äÊäääÊ ÓäÊäää
Polar Response
äÂ
³x°ä
ä°ä
Ó°ä Ó°ä
{°ä
È°ä
n°ä
£ä°ä Ê£ä°äÊÊ
£Ó°ä
£{°ä
£È°ä
£n°ä
Óä°ä Óä°ä
ÓÓ°ä
Ó{°ä
Óx°ä ä ÓÇä
` ÊÀi°Ê£6É*>
––
ÀiµÕiVÞ\
Ê xääÊâ\
–
£äääÊâ\
{äääÊâ\ £näÂ
Accessories
Stand mount Zip pouch
Wind shield
-4-
Features
• Broadcast sound quality
• Low noise circuitry
• Condenser transducer
• Rugged metal construction
• Low handling noise
• Includes stand mount, zip pouch and windshield
• Designed & manufactured in Australia
• Full 10 year guarantee*
Supplying Power
• The NTG-1 requires power to operate. This needs
to be supplied via P48V phantom power supply
which is available from most professional video
cameras or mixing consoles.
• If the mixer or preamp does not contain this
phantom power requirement, then an external
phantom power supply is needed.
• Some phantom power supplies do not supply the
voltage at which they are rated. If the required
voltage is not supplied, the dynamic range and
general performance of the microphone will be
reduced.
• We strongly suggest the use of a reputable high
quality power supply. Damage caused by a faulty
power supply is not covered by the warranty.
*Online product registration required.
-5-
Mounting the NTG-1
• The NTG-1 comes complete with a heavy duty
stand mic holder for mounting the microphone on
any compatible stand with a 3/8” or 5/8” thread.
• Install as shown by pushing the mic in on an angle
coming from the back. You will notice the holder
is quite firm, and this is intentional so that the
the NTG-1 will not come out easily, which could
damage the mic.
• Make sure you do not block the slots on the side
of the mic (Fig 3) as blocking these will affect the
sound quality and the polar pattern (directional
qualities).
-6-
Using the NTG-1
• The NTG-1 incorporates a switchable high pass
filter set at 80 Hz. This can be used when you wish
to remove low frequency noise that is not part of
your intended sound source. Remember however
the tonal characteristics will be affected by this, so
it is important that you listen to the sound with and
without the HPF in circuit before deciding if it is
appropriate for the source.
• The HPF activated by the recessed
switch shown to the right. A small
screwdriver or pen will be required
as the switch is designed to prevent
accidental toggling.
High Pass Filter ON
High Pass Filter OFF/Flat
• While it may sound like a contradiction, Shotgun
microphones have a narrow pick-up angle or polar
response, and so can be used to great effect with
cameras for news gathering, weddings, sporting
events or any situation where you want to focus on
a particular area of sound source without having
your audio overpowered by ambient noise.
• The NTG-1 is supplied with a foam windshield.
This windshield should be used even in the
slightest breeze, as this can cause sound
interference.
• When using the mic outside in heavy winds you
may need to purchase a more specialised wind
shield, such as the Dead Cat, which will
provide additional protection from adverse wind
conditions.
-7-
Warranty
All microphones are warranted for one year
from date of purchase. You can extend that to a full
ten years if you register online at [Link].
The warranty covers parts and labour that may be
required to repair the microphone during the warranty
period. The warranty excludes defects caused by
normal wear and tear, modification, shipping damage,
or failure to use the microphone as per the instruction
guide.
If you experience any problem, or have any questions
regarding your microphone, first contact the
dealer who sold it to you. If the microphone requires a
factory authorised service, return will be organised by
that dealer.
We have an extensive distributor/dealer network, but
if you have difficulty getting the advice or assistance
you require, do not hesitate to contact us directly.
Microphones
International
107 Carnarvon Street
Silverwater NSW 2128 Australia
Ph: +61 2 9648 5855
Fax: +61 2 9648 2455
USA
P.O. Box 4189
Santa Barbara, CA 93140-4189
Ph: 805 566 7777
Fax: 805 566 0071
Technical Support
For information and technical support questions contact:
support@[Link]
In the Unites States and Puerto Rico, contact
usasupport@[Link] or call 805 566 7777
In Australia, contact ozsupport@[Link] or call (02) 9648 5855
Anywhere except Australia, the United States and Puerto Rico,
contact support@[Link] or call +61 2 9648 5855
-8-
