BULLETIN NO.

SERVICE PARTS LIST 54-26-2755

SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS REVISED BULLETIN DATE
May 2019
M18™ FUEL™ 1/4" Hex Impact Driver (Baseline)
WIRING INSTRUCTION
STARTING
CATALOG NO. 2753-20 SERIAL NO. G76A SEE PAGE 2
EXAMPLE:
00 0 Component Parts (Small #) Are Included IMPORTANT NOTE: Gearcase end cap #68 is
When Ordering The Assembly (Large #). LEFT HAND THREAD!
71 30
37
36
As an aid to assembly,
carefully lower the complete
front end of tool (gearcase /
impacting system) onto the
gearcase end cap. Gently
70 40 hand tighten front end
assembly onto gearcase
30 end cap. Be careful not
50 (4x) to cross-thread! Once
47 installed by hand, seat
45 gearcase end cap with a
good adjustable wrench
(6x) 69 using light pressure. 2
36 Do not over tighten! 1
68
24 LEFT HAND THREAD

39 NOTE: Components of
the Impacting Assembly
73 47 (67) can drop out of the
18 gearcase (6). Care must
(2x) be taken to hold these
37 elements in place when
assembling onto the
72 gearcase end cap (68).
51
67 18
24
13
11 1 2 3 4 5 6
38
65 9 10 11 12 13 68
10 12
10 6
74 47 NOTE: Place anvil 1
spring (10) onto anvil 9
(12) with curled end 5
inserted in slot of anvil 3
as shown. Place steel
ball (11) in anvil slot in 12
front of spring. 11
47 44(2x)
81
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
1 31-12-0017 Rubber Cap (1) 2
2 42-76-0019 Sleeve (1) 4
3 34-60-0725 Retaining Ring (1)
4 45-88-2026 Washer (1)
5 40-50-1470 Spring (1) FIG. PART NO. DESCRIPTION OF PART NO. REQ.
6 28-50-0013 Gearcase with Bushing (1) 70 16-07-0012 Rotor Assembly (1)
9 45-88-2653 Plastic Washer (1) 71 31-44-0023 Housing Halve Assembly (1)
10 40-50-0057 Anvil Spring (1) 72 45-24-0017 Speed Selector Assembly (1)
11 02-02-0170 3.5mm Steel Ball (1) 73 42-70-0059 Belt Clip Assembly (1)
12 42-06-0017 1/4" Hex Anvil (1) 74 43-72-0046 Bit Holder Assembly (1)
13 02-02-1300 5mm Steel Ball (1) 81 49-12-0011 Rubber Boot (Optional, Accessory) (1)
18 02-02-0180 3/16" Steel Ball (2)
24 --------------- Ring Gear (1)
30 45-30-0022 Rubber Slug (4) FIG. LUBRICATION
(Type 'J' Grease, No. 49-08-4220):
36 --------------- Right Handle Halve (1)
37 --------------- Left Handle Halve (1) 11,12 Lightly coat front washer surface of anvil (12) with grease,
38 40-50-1090 Compression Spring (1) place a dab in the ball slot of anvil and in needle bearing
39 06-82-7336 M3 x 20mm Pan Hd. ST T-10 Screw (1) inside the anvil.
40 45-24-0013 Forward/Reverse Shuttle (1)
24,67 Lightly coat the I.D. of the ring gear (24) and the center of
44 06-82-0013 M3 x 38mm Pan Hd. ST T-10 Tamproof (2) the planet gears of impacting assembly with grease.
45 06-82-7236 M3 x 16mm Pan Hd. ST T-10 Tamproof (6)
47 06-82-0130 6-32 x 5/16" Pan Hd. T-15 Machine Scr. (2) 6 Coat inside of bushing inside front gearcase with grease.
50 42-55-2753 Blow Molded Carrying Case (1)
51 12-20-0068 Service Nameplate (1) 70 Coat pinion of rotor assembly (70) with grease.
65 14-30-0012 Gearcase Assembly (1)
67 14-46-0014 Impacting Assembly (1)
68 44-66-0023 Gearcase End Cap with Ball Bearing (1)
69 14-20-0013 Electronics Assembly
Consisting of: On-Off Switch, PCBA,
Stator, LED, HV Protection and Battery
MILWAUKEE TOOL l [Link]
13135 W. Lisbon Road, Brookfield, Wisc. 53005
Connector Block (1) Drwg. 2


Rotor Assembly

High Voltage
Protection Wire.
Place terminal
over screw boss
and route down
in cavity behind
forward/reverse
shuttle.

Route LED wires

down in cavity
behind forward/
reverse shuttle.
Stator Assembly
with Hall PCBA
LED Assembly
Watch for pinched wires here.
Tuck leads down in cavity On-Off Switch
behind switch.

Main PCBA

Speed PCBA

Speed Selector Assembly

Battery Connector
Block Assembly

Compression
Spring