PowerSDR keyboard shortcuts.
PowerSDR must be in FOCUS (Mouse Click somewhere on the PowerSDR console screen) for the
PowerSDR to respond to keyboard input.
OR
AUTO FOCUS OPTION:
Setup->General->Hardware Config->Auto Focus PowerSDR
This will attempt to auto focus PSDR when moving the mouse back onto the PowerSDR console screen
from another application.
!!!!!!!!!!!WARNING!!!!!!!!!!!!!!!
DO NOT touch anything on Hidden PowerSDR (Calibration and/or Test) pages unless you are willing to
brick your radio if you mess up, which may require you to send your Radio to Flex for Repair.
Calibrations will not work correctly unless you are at Factory Defaults, and you follow Flex Calibration
procedures completely.
Function Key ALT CTRL ALT + CTRL CTRL + SHIFT Shift + ALT
Ke9ns: Mouse over a Right
PowerSDR button usually mouse
brings you to its SETUP Click
page
OR
Ke9ns: Mouse over a DX
spot on Pan, opens QRZ
page
OR
Ke9ns: Mouse over a SWL
spot on Pan, opens Google
page
OR
Ke9ns: Mouse over ID
timer, toggles between
voiceID, waterID, and Pop-
Up
Ke9ns: Show DX Spotters SHIFT
on Pan and Lat/Long on
Pan (instead of DX Spots)
Or
With Mouse over Band
Button causes dec in the
BandStack.
Or
Resets Database to Factory
Defaults if Held at Power
UP.
Ke9ns: When mouse over a CTRL
DX spot, sets VFOA, Mode,
Split, and RX Filter to that
DX Spot
Change VFO Freq (by the Mouse
current Tune Step amount) Wheel
Change VFO Freq (by the PowerMate
Alt Tune Step amount) Knob
setup->general->user
interface->Alt1 and Alt2
(knob pushed)
-1 MHz A
+ RX FILTER (F1- B
F10,VAR1/2)
C
-10 KHz D
+10 KHz E
-1 KHz F
-100 Hz G
-10 Hz H
- RIT I
-1 Hz J
Filter width inc (50hz) K
Filter width dec (50hz) L
+ BAND M
- BAND N
+ RIT O
- XIT P
+1 MHz Q
+1 KHz R
-100 KHz S
+100 Hz T
+1 Hz U
- RX FILTER (F1- V
F10,VAR1/2)
+100 KHz W
+ MODE X
+10 Hz Y
- MODE Z
Automatically finishes an ENTER
“Accept” button Enter Key
operation(if the control
features an Accept button)
Or
Whatever windows object
has the current Focus
Cancel button (if the ESC
control features a Cancel
button)
(LEFT) Mouse Click over Space Bar
the last selected control Space
(current Focused object)
Allows direct VFOA 0-9 and . or
frequency Entry ,
+ XIT [
]
CW DOT (doesn’t appear to .
be hooked up)
CW DASH (doesn’t appear ?
to be hooked up)
Toggle MUT button * (keypad
only)+
AF level inc + (keypad
only)
AF level dec - (keypad
only)
Ke9ns: Help screen (mouse F1
must be over item
requesting help)
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
Flex-3000: ATU form CTRL SHIFT A
Hidden: EEPROM CTRL SHIFT C
calibration form
Hidden: Debug form CTRL SHIFT D
Hidden: Flex-3000/5000: CTRL SHIFT F
PA Calibration form. Use to
reCal your transmitter
Hidden: Flex-3000/5000: CTRL SHIFT I
Volts & Temp
Hidden: Flex-5000: Relays CTRL SHIFT O
menu item add
(TX1,TX2,TX3)
Hidden: TRX I/O Test and CTRL SHIFT P
Calibration form. Use to
reCal your receiver.
(general, RX, TX image &
carrier & filter, I/O
calibration and tests)
Hidden: Flex-5000: TRX2 CTRL SHIFT R
I/O Test and Calibration
form. Use to reCal RX2
Hero’s Preselector (3rd CTRL SHIFT S
party option) screen
Hidden: SDR-1000 PA CTRL SHIFT T
Qualify form
Hidden: Flex-5000: VU5K CTRL SHIFT V
option Calibration form
About form CTRL ALT A
Hidden: Flex-5000: LPF CTRL ALT 4
(low pass filter) manual
override form (RX1 and
RX2)
Hidden: DSP test form CTRL ALT D
(WBIQ, Manual Notch, NR,
ANF, DC Block)
Hidden: Flex-1500: TX CTRL ALT G
image calibration form
Flex-5000 (RX2 only) ESC CTRL ALT R
(Enhanced Signal Clarity)
FlexWire UCB config and CTRL ALT U
setup form (I^C bus)
Hidden: Toggles Full CTRL ALT F
Duplex button on/off
(button located just to left
of words “Tune Step:”)
Change AGC-T level inc CTRL +
( see CTRL R)
Change AGC-T level dec CTRL -
( see CTRL E)
Change Tune Step Up CTRL (left
(larger step) arrow)
Change Tune Step Dwn CTRL
(smaller step) (right
arrow)
Mouse Wheel: Freq inc (by CTRL (up
Tune Step amount) arrow)
Mouse Wheel: Freq dec (by CTRL
Tune Step amount) (dwn
arrow)
QuickSave current Freq CTRL C
(just below VFO LOCK
button)
Toggle between: Spectrum, CTRL D
and Panadapter modes
Change AGC-T level dec CTRL E
Narrow current RX filter by CTRL F
5hz (see ALT F)
Toggle VFO LOCK button CTRL L
Toggle MOX button CTRL M
Toggle ANF button CTRL N
Toggle PreAmp mode CTRL P
Change AGC-T level inc CTRL R
Toggle SPLIT button CTRL S
Toggle RESTORE button CTRL V
(QuickSave restore)
CW speed value dec CTRL W
(see ALT Q)
Ke9ns: WORLD MAP CTRL Z
Mic level inc ALT (up
arrow)
Mic level dec ALT (dwn
arrow)
Vox level inc ALT (left
arrow)
Vox level dec ALT (right
arrow)
Drive level inc ALT +
Drive level dec ALT -
Widen current RX filter by ALT F
5hz (see CTRL F)
VFO A > B button ALT G
VFO B > A button ALT H
RX Filter Shift Reset button ALT I
Ke9ns: Add new Memory ALT M
directly from current
Panadapter
Toggle NB2 button ALT N
CW speed value inc ALT Q
(see CTRL W)
RIT Reset buton ALT R
Toggle TUN button ALT T
VFO A<>B button ALT V
XIT Reset button ALT Y
Zero Beat button ALT Z
CWX Panel
Must be in Focus for
keyboard to work
Macro 1 ALT1
Macro 2 ALT2
Marco 3 ALT3
Macro 4 ALT4
Macro 5 ALT5
Macro 6 ALT6
Macro 7 ALT7
Macro 8 ALT8
Macro 9 ALT9
DTMF Tones
Setup->Keyboard->DTMF
OR PSDR must be in Focus
for Keyboard to work
DTMF Tone 1 ALT 1
DTMF Tone 2 ALT 2
DTMF Tone 3 ALT 3
DTMF Tone 4 ALT 4
DTMF Tone 5 ALT 5
DTMF Tone 6 ALT 6
DTMF Tone 7 ALT 7
DTMF Tone 8 ALT 8
DTMF Tone 9 ALT 9
DTMF Tone 0 ALT 0
DTMF Tone * ALT SHIFT 8
DTMF Tone # ALT SHIFT 3
Hidden: Setup “PA CTRL ALT A
Settings” calibrate screen
visible
Hidden: Setup Signal CTRL ALT O
Generator TX Output
visible
!!!!!!!!!!!WARNING!!!!!!!!!!!!!!!
DO NOT touch anything on Hidden PowerSDR (Calibration and/or Test) pages unless you are willing to
brick your radio if you mess up, which may require you to send your Radio to Flex for Repair.
Calibrations will not work correctly unless you are at Factory Defaults, and you follow Flex Calibration
procedures completely.
