Scribd
Upload
419 views2 pages

Drop Weight Crusher Crushing Law Test

This document describes a procedure to determine crushing law constants using a drop weight crusher. Samples of various sizes are crushed in the apparatus by dropping a weight from a measured height. The crushed material is sieved and weighed to determine the particle size distribution. Formulas are given to calculate the energy required for crushing and constants like the Work Index, Rittinger's constant, and Kick's constant based on the results. The goal is to apply these formulas to the experimental data to determine the crushing law constants.

Uploaded by

muralidharan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
419 views2 pages

Drop Weight Crusher Crushing Law Test

This document describes a procedure to determine crushing law constants using a drop weight crusher. Samples of various sizes are crushed in the apparatus by dropping a weight from a measured height. The crushed material is sieved and weighed to determine the particle size distribution. Formulas are given to calculate the energy required for crushing and constants like the Work Index, Rittinger's constant, and Kick's constant based on the results. The goal is to apply these formulas to the experimental data to determine the crushing law constants.

Uploaded by

muralidharan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd

DROP WEIGHT CRUSHER

AIM:
To determine the crushing law of constants using drop weight crusher.
APPARATUS REQUIRED:
Drop weight crusher set up, sieves, samples etc.
PROCEDURE:
1. About 25 grams of the sample size 4+5 is taken in the crusing chamber.
2. The weight of the metallic block (weight to be dropped) and the height through which it
falls is determined.
3. The block is kept in position and the plunger is placed on the top to the feed.
4. The weight Is allowed to drop on the plunger. The sample in the chamber is reshuffled
after every 5 drops, so that the lower layers are also exposed to the impact.
5. The product is analyzed after 100 drops using he standard set of screens.
6. The crushed material is transferred to a sieve stack and mechanically agitated for 10
minutes.
7. The quantity of samples retained on each sieve is weighed and tabulation as shown in
the table. The screen analysis data is used to determine the volume mean diameter of the
product (Dp)
OBSERVATION
Quantity of feed sample = Tones
Feed size, Df = mm
Height through which weight falls, h = m
Weight of the drop, w = Tones
[Link] Drops, n =

TABULATION:

3
SL. Mesh Size of Average Dpi Mass in Mass xi/Dpi
NO No. Aperture Particle size each Fraction
Da (mm) in each fraction (Xi)
fraction Dpi (gms)
(mm)

New no. 3, Old No. 2, S.V . Koil street, Sekar Nagar, Ashok Nagar, Chennai – 600 083
Phone: +91 (044), 4351 8677 | cell: (+91) 9789976777, 9789975777& 9940077338
email: elshaddaiee@[Link], elshadaiee@[Link], [Link]
FORMULAE REQUIRED:

1) Energy required for crushing


E=[nwgh] ÷ [m] kW hr/Ton

2) Volume surface mean diameter of the product


3]1/3
Dp=[1÷ ∑xi/Dpi

3) Work Index[Bond’s law constant)


Wi=[E] ÷[1/∫Dp-1/∫Df]

4) Rittinger’s constant
KR fc=[E] ÷[1/Dp-1/Df]

5) Kick’s Constant
KKfc=[E]÷1n(Df/Dp)

RESULT:
The crushing law constants are determined
Wi =_____________________
KRfc =_________________________________
Kkfc=__________________________________

New no. 3, Old No. 2, S.V . Koil street, Sekar Nagar, Ashok Nagar, Chennai – 600 083
Phone: +91 (044), 4351 8677 | cell: (+91) 9789976777, 9789975777& 9940077338
email: elshaddaiee@[Link], elshadaiee@[Link], [Link]

You might also like