Draft ETSI EN 300 674-2-2 V2.0.

3 (2016-03)

HARMONISED EUROPEAN STANDARD

Transport and Traffic Telematics (TTT);

Dedicated Short Range Communication (DSRC) transmission
equipment (500 kbit/s / 250 kbit/s) operating in the 5,8 GHz
Industrial, Scientific and Medical (ISM) band;
Part 2: Harmonised Standard covering the essential
requirements of article 3.2 of the Directive 2014/53/EU;
Sub-part 2: On-Board Units (OBU)
 2 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

Reference
REN/ERM-TG37-27

Keywords
data, DSRC, radio, regulation, RTTT, testing

ETSI

650 Route des Lucioles

F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C

Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice

The present document can be downloaded from:

[Link]

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.

Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
[Link]

If you find errors in the present document, please send your comment to one of the following services:
[Link]

Copyright Notification

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2016.

All rights reserved.

DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.

ETSI
 3 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

Contents
Intellectual Property Rights ................................................................................................................................6
Foreword.............................................................................................................................................................6
Modal verbs terminology....................................................................................................................................6
1 Scope ........................................................................................................................................................7
2 References ................................................................................................................................................7
2.1 Normative references ......................................................................................................................................... 7
2.2 Informative references ........................................................................................................................................ 8
3 Definitions, symbols and abbreviations ...................................................................................................9
3.1 Definitions .......................................................................................................................................................... 9
3.2 Symbols ............................................................................................................................................................ 10
3.3 Abbreviations ................................................................................................................................................... 12
4 Technical requirements specifications ...................................................................................................13
4.1 Mechanical and electrical design...................................................................................................................... 13
4.1.1 Units............................................................................................................................................................ 13
4.1.2 Controls ...................................................................................................................................................... 13
4.1.3 OBU assemblies.......................................................................................................................................... 13
4.2 General characteristics ..................................................................................................................................... 14
4.2.1 OBU sets ..................................................................................................................................................... 14
4.2.2 Uplink sub-carrier frequencies .................................................................................................................... 14
4.2.3 Carrier frequencies ...................................................................................................................................... 14
4.2.4 Modulation.................................................................................................................................................. 14
4.3 Environmental conditions ................................................................................................................................. 15
4.3.1 Environmental profile ................................................................................................................................. 15
4.3.2 Power supply .............................................................................................................................................. 15
4.4 Conformance requirements .............................................................................................................................. 15
4.4.1 Transmitter parameters ............................................................................................................................... 15
[Link] General .................................................................................................................................................. 15
[Link] Transmitter spectrum mask ................................................................................................................... 15
[Link] Maximum equivalent isotropically radiated power ............................................................................... 15
[Link] Transmitter frequency error .................................................................................................................. 16
[Link] Transmitter unwanted emissions ........................................................................................................... 16
4.4.2 Receiver parameters .................................................................................................................................... 16
[Link] General .................................................................................................................................................. 16
[Link] Receiver unwanted emissions in the spurious domain .......................................................................... 17
[Link] Sensitivity ............................................................................................................................................. 17
[Link] Receiver selectivity ............................................................................................................................... 17
[Link].1 General ............................................................................................................................................ 17
[Link].2 Receiver spurious response rejection............................................................................................... 17
[Link].3 Receiver blocking ............................................................................................................................ 18
4.4.3 Antennas ..................................................................................................................................................... 18
5 Testing for compliance with technical requirements..............................................................................19
5.1 Environmental conditions for testing ............................................................................................................... 19
5.2 Interpretation of the measurement results ........................................................................................................ 19
5.3 Essential radio test suites .................................................................................................................................. 19
5.3.1 Transmitter parameters ............................................................................................................................... 19
[Link] Transmitter spectrum mask ................................................................................................................... 19
[Link].1 General ............................................................................................................................................ 19
[Link].2 Radiated measurements ................................................................................................................... 20
[Link].3 Conducted measurements ................................................................................................................ 22
[Link] Maximum equivalent isotropically radiated power ............................................................................... 23
[Link].1 General ............................................................................................................................................ 23
[Link].2 Radiated measurement ..................................................................................................................... 24
[Link].3 Conducted measurement.................................................................................................................. 25
[Link] Transmitter frequency error .................................................................................................................. 25

ETSI
 4 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

[Link].1 General ............................................................................................................................................ 25

[Link].2 Radiated measurements ................................................................................................................... 25
[Link].3 Conducted measurements ................................................................................................................ 26
[Link] Transmitter unwanted emissions ........................................................................................................... 26
[Link].1 General ............................................................................................................................................ 26
[Link].2 Radiated measurement ..................................................................................................................... 27
5.3.2 Receiver parameters .................................................................................................................................... 28
[Link] Receiver unwanted emissions in the spurious domain .......................................................................... 28
[Link].1 General ............................................................................................................................................ 28
[Link].2 Radiated measurement ..................................................................................................................... 28
[Link] Sensitivity ............................................................................................................................................. 28
[Link].1 General ............................................................................................................................................ 28
[Link].2 Radiated measurements ................................................................................................................... 28
[Link].3 Conducted measurements ................................................................................................................ 29
[Link] Receiver selectivity ............................................................................................................................... 30
[Link].1 General ............................................................................................................................................ 30
[Link].2 Unwanted signal characteristics ...................................................................................................... 30
[Link].3 Measurement of receiver selectivity in OBU boresight ................................................................... 30

Annex A (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU .........................................................32
Annex B (normative): Basics on testing .............................................................................................33
B.1 General conditions..................................................................................................................................33
B.1.1 Power source .................................................................................................................................................... 33
B.1.2 Thermal balance ............................................................................................................................................... 33
B.1.3 Test signals ....................................................................................................................................................... 33
B.1.4 Test sites ........................................................................................................................................................... 34
B.1.4.1 Shielded anechoic chamber......................................................................................................................... 34
B.1.4.2 Open area test site ....................................................................................................................................... 35
B.1.4.3 Test fixture .................................................................................................................................................. 36
B.1.5 General requirements for RF cables ................................................................................................................. 37
B.1.6 Conducted measurements ................................................................................................................................. 37
B.1.6.1 One antenna connector arrangement ........................................................................................................... 37
B.1.6.2 Two antenna connectors arrangement......................................................................................................... 38
B.1.6.3 Test site requirements ................................................................................................................................. 39
B.1.6.4 Site preparation for conducted measurements ............................................................................................ 39
B.[Link] Monochromatic signals ......................................................................................................................... 39
B.[Link] Modulated signals ................................................................................................................................. 39
B.1.7 Radiated measurements .................................................................................................................................... 39
B.1.7.1 One antenna arrangement ........................................................................................................................... 39
B.1.7.2 Two antennas arrangement ......................................................................................................................... 41
B.1.7.3 Test site requirements ................................................................................................................................. 42
B.[Link] Measurement distances ......................................................................................................................... 42
B.[Link] Free-space wave propagation ................................................................................................................ 42
B.1.7.4 Test and substitution antennas .................................................................................................................... 43
B.1.7.5 Site preparation for radiated OBU measurements ...................................................................................... 43
B.[Link] Monochromatic signals ......................................................................................................................... 43
B.[Link] Modulated signals ................................................................................................................................. 45
B.[Link] Arrangement for OBU transmitter unwanted emissions measurement ................................................. 46
B.[Link] Arrangement for OBU receiver selectivity measurement ..................................................................... 48
B.2 Instruments ....................................................................................................................................................... 49
B.2.1 Receiving device ......................................................................................................................................... 49
B.2.2 RF power sensor ......................................................................................................................................... 50
B.2.3 Combiner .................................................................................................................................................... 51
B.3 Power of modulated RSU carrier ..................................................................................................................... 51
B.4 Bit error ratio measurements ............................................................................................................................ 52
B.4.1 Basics .......................................................................................................................................................... 52
B.4.2 BER measurement ...................................................................................................................................... 52
B.4.3 FER measurement ....................................................................................................................................... 52
B.4.3.1 Mathematical expressions ..................................................................................................................... 52

ETSI
 5 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

B.4.3.2 Equipment ............................................................................................................................................. 53

B.4.3.3 Procedure .............................................................................................................................................. 53

Annex C (informative): Guidance on declaring the environmental profile ......................................54

C.1 Recommended environmental profile ....................................................................................................54
C.2 Normal environmental conditions ..........................................................................................................54
C.3 Extreme environmental conditions .........................................................................................................54
Annex D (informative): Bibliography ...................................................................................................55
Annex E (informative): Change History ..............................................................................................56
History ..............................................................................................................................................................57

ETSI
 6 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

Intellectual Property Rights

IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server ([Link]

Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.

Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote
phase of the ETSI standards EN Approval Procedure.

The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.6] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.5].

Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.

The present document is sub-part 2 of part 2 of a multi-part deliverable covering Transport and Traffic Telematics
(TTT); Dedicated Short Range Communication (DSRC) transmission equipment (500 kbit/s / 250 kbit/s) operating in
the 5,8 GHz Industrial, Scientific and Medical (ISM) band, as identified below:

Part 1: "General characteristics and test methods for Road Side Units (RSU) and On-Board Units (OBU)";

Part 2: "Harmonised Standard covering the essential requirements of article 3.2 of the Directive
2014/53/EU";

Sub-part 1: "Road Side Units (RSU)";

Sub-part 2: "On-Board Units (OBU)".

Proposed national transposition dates

Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 2017-06-12

Modal verbs terminology

In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).

"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI
 7 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

1 Scope
The present document applies to Transport and Traffic Telematics (TTT) systems:

- with a Radio Frequency (RF) output connection and specified antenna or with an integral antenna;

- for data transmission only;

- operating on radio frequencies in the 5,725 GHz to 5,875 GHz Industrial, Scientific and Medical (ISM)
frequency band.

The applicability of the present document covers only the On Board Units (OBU).

The present document does not necessarily include all the characteristics which may be required by a user, nor does it
necessarily represent the optimum performance achievable.

The present document complies with the Commission Implementing Decision 2013/752/EU [1] and CEPT/ERC
Recommendation 70-03 [2]. It is a specific standard covering various TTT applications.

The present document applies to the following radio equipment types operating in all or in part of the following service
frequency bands given in table 1.

Table 1: Frequency bands and centre frequencies fTx allocated for DSRC

Pan European Service Frequencies National Service Frequencies

Channel 1 5,795 GHz to 5,800 GHz, fTx = 5,7975 GHz
Channel 2 5,800 GHz to 5,805 GHz, fTx = 5,8025 GHz
Channel 3 5,805 GHz to 5,810 GHz, fTx = 5,8075 GHz
Channel 4 5,810 GHz to 5,815 GHz, fTx = 5,8125 GHz

The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the
efficient use of radio spectrum in order to avoid harmful interference.

2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.

Referenced documents which are not found to be publicly available in the expected location might be found at
[Link]

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.

The following referenced documents are necessary for the application of the present document.

[1] Commission Decision 2013/752/EU: "Commission Implementing Decision of 11 December 2013

amending Decision 2006/771/EC on harmonisation of the radio spectrum for use by short-range
devices and repealing Decision 2005/928/EC".

[2] CEPT/ERC Recommendation 70-03 (2015): "Relating to the use of Short Range Devices (SRD)".

[3] CEN EN 12253 (2004): "Road transport and traffic telematics - Dedicated short-range
communication - Physical layer using microwave at 5,8 GHz".

[4] ETSI TR 100 028 (V1.4.1) (12-2001) - (all parts): "Electromagnetic compatibility and Radio
spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment
characteristics".

ETSI
 8 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

[5] IEC 60721-3-4 (1995) including Amendment 1 (1996): "Classification of environmental

conditions - Part 3: Classification of groups of environmental parameters and their severities -
Section 4: Stationary use at non-weatherprotected locations".

[6] IEC 60721-3-5 (1997): "Classification of environmental conditions - Part 3: Classification of

groups of environmental parameters and their severities - Section 5: Ground vehicle installations".

[7] CEN EN 12795 (2003): "Road transport and traffic telematics - Dedicated Short Range
Communication (DSRC) - DSRC data link layer: medium access and logical link control".

[8] CEN EN 12834 (2003): "Road transport and traffic telematics - Dedicated Short Range
Communication (DSRC) - DSRC application layer".

[9] ISO 14906 (2011): "Electronic fee collection - Application interface definition for dedicated
short-range communication".

[10] CEPT/ERC Recommendation 74-01E (2011): "Spurious Emissions".

[11] ETSI TR 102 273-2 (V1.2.1) (12-2001): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Improvement on Radiated Methods of Measurement (using test site) and
evaluation of the corresponding measurement uncertainties; Part 2: Anechoic chamber".

[12] ETSI TR 102 273-6 (V1.2.1) (12-2001): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Improvement on Radiated Methods of Measurement (using test site) and
evaluation of the corresponding measurement uncertainties; Part 6: Test fixtures".

[13] CEN EN 13372 (2004): "Road Transport and Traffic Telematics (RTTT) - Dedicated short-range
communication - Profiles for RTTT applications".

[14] CISPR 16-1 (2015): "Specification for radio disturbance and immunity measuring apparatus and
methods - Part 1: Radio disturbance and immunity measuring apparatus".

2.2 Informative references

References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.

The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.

[i.1] ETSI EN 300 674-1: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Road
Transport and Traffic Telematics (RTTT); Dedicated Short Range Communication (DSRC)
transmission equipment (500 kbit/s / 250 kbit/s) operating in the 5,8 GHz Industrial, Scientific and
Medical (ISM) band; Part 1: General characteristics and test methods for Road Side Units (RSU)
and On-Board Units (OBU)".

[i.2] ETSI EN 300 674-2-1: "Transport and Traffic Telematics (TTT); Dedicated Short Range
Communication (DSRC) transmission equipment (500 kbit/s / 250 kbit/s) operating in the 5,8 GHz
Industrial, Scientific and Medical (ISM) band; Part 2: Harmonised Standard covering the essential
requirements of article 3.2 of the Directive 2014/53/EU; Sub-part 1: Road Side Units (RSU)".

[i.3] ETSI TR 102 273-4 (V1.2.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Improvement on Radiated Methods of Measurement (using test site) and evaluation of the
corresponding measurement uncertainties; Part 4: Open area test site".

[i.4] Commission Directive 95/54/EC of 31 October 1995 adapting to technical progress Council
Directive 72/245/EEC on the approximation of the laws of the Member States relating to the
suppression of radio interference produced by spark-ignition engines fitted to motor vehicles and
amending Directive 70/156/EEC on the approximation of the laws of the Member States relating
to the type-approval of motor vehicles and their trailers.

ETSI
 9 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

[i.5] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.

[i.6] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.

3 Definitions, symbols and abbreviations

3.1 Definitions
For the purposes of the present document, the terms and definitions given in Directive 2014/53/EU [i.5] and the
following apply:

adjacent channel: channel at a distance of 5 MHz relative to the centre frequency, i.e. in the channel at the next upper
or lower centre frequency within the frequency band allocated for DSRC (see table 3)

bit: acronym for "binary digit" which can have one out of two possible values

EXAMPLE: 0/1, or +1/-1, or low/high.

bit rate: in a bit stream, the number of bits occurring per unit time, usually expressed in bits per second

boresight: direction of maximum radiation of a directional antenna

NOTE: If boresight cannot be determined unambiguously, then boresight may be declared by the manufacturer.

carrier frequency: frequency fTx to which the RSU transmitter is tuned

NOTE: In DSRC, the carrier frequency is in the centre of a channel, see table 3 of the present document.

carrier signal or carrier: harmonic signal whose nominal single frequency fTx can vary within a range specified by the
carrier frequency tolerance and which is capable of being modulated by a second, symbol-carrying signal

channel: continuous part of the radio-frequency spectrum to be used for a specified emission or transmission

NOTE: A radio-frequency channel may be defined by two specified limits, or by its centre frequency and its
bandwidth, or any equivalent indication. It is often designated by a sequential number. A radio-frequency
channel may be time-shared in order to allow radio communication in both directions by simplex
operation. The term "channel" is sometimes used to denote two associated radio-frequency channels, each
of which is used for one of two directions of transmission, i.e. in fact a telecommunication circuit.

co-channel: transmission using the same channel (frequency band of 5 MHz width)

cross-polar discrimination (XPD): the ratio PLHCP / PRHCP of power PLHCP of the left hand circular polarized wave to
the power PRHCP of the right hand circular wave when the total power of the transmitted wave is PLHCP + PRHCP

downlink: transmission in direction from RSU to OBU

ellipticity of polarization: ratio of the polarization main axes of an elliptic polarized radio wave

EXAMPLE: The ellipticity of circular polarized radio waves is one.

The ellipticity of linear polarized waves is infinity.

environmental profile: range of environmental conditions under which equipment within the scope of the present
document is required to comply with the provisions of the present document

equivalent isotropically radiated power: signal power fed into an ideal loss-less antenna radiating equally in all
directions that generates the same power flux at a reference distance as the one generated by a signal fed into the
antenna under consideration in a predefined direction within its far field region

integral antenna: antenna, with or without a connector, designed as an indispensable part of the equipment

ETSI
 10 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

OBU sleep mode: optional mode for battery powered OBUs that allows to save battery power

NOTE: In this mode, the OBU can only detect the presence of a DSRC downlink signal to initiate under certain
defined conditions a transition to the stand-by mode.

OBU stand-by mode: mode, in which the OBU is capable of receiving DSRC downlink signals, but is never
transmitting

operating frequency: nominal frequency at which equipment is operated; also referred to as the operating centre
frequency

NOTE: Equipment may be able to operate at more than one operating frequency.

out-of-band emissions: emissions on a frequency or frequencies immediately outside the necessary bandwidth which
results from the modulation process and which cannot be reduced without affecting the corresponding transmission of
information, but excluding spurious emissions (see also CEPT/ERC Recommendation 74-01E [10])

polarization: locus of the tip of the electrical field vector in a plane perpendicular to the direction of transmission

EXAMPLE: Horizontal and vertical linear polarization

Left and right hand circular polarization.

Portable Equipment (PE): generally intended to be self-contained, free standing and portable

NOTE: A PE would normally consist of a single module, but may consist of several interconnected modules. It is
powered by one or more internal batteries.

radiated measurements: measurements which involve the measurement of a radiated electromagnetic field

spurious emissions: emission on a frequency, or frequencies, which are outside an exclusion band of ±2,5 times the
channel spacing around the selected centre frequency fTx, and the level of which may be reduced without affecting the
corresponding transmission of information

NOTE: Spurious emissions include harmonic emissions, parasitic emissions, intermodulation products and
frequency conversion products but exclude out-of-band emissions (see also CEPT/ERC
Recommendation 74-01E [10]).

uplink: transmission in direction from OBU to RSU

3.2 Symbols
For the purposes of the present document, the following symbols apply:

ACW Amplitude of CW signal

Amod Amplitude of modulated signal
ATNAT2 Attenuation of attenuator AT2
ATNBLN Attenuation of balun BLN
ATNCA1 Attenuation of calibrated coaxial cable 1
BER Bit error ratio
CF Number of frames transmitted
CE Number of erroneous frames received
d Distance between phase centres of transmitting and receiving antenna
ddisplace Horizontal displacement of TTA and RTA antenna phase centres
dF1 Distance from transmitting antenna to first Fresnel ellipse
dF2 Distance from first Fresnel ellipse to receiving antenna
Dfb Distance between neighbouring ferrite beads
Di Directivity relative to an isotropic radiator
D0,TA Largest linear dimension of test antenna
D0,EUT Largest linear dimension of EUT antenna
EIRPmax Maximum e.i.r.p. of RSU
EIRPMaxObuTx Maximum e.i.r.p. generated by the OBU in a single side band

ETSI
 11 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

EIRPObuTx e.i.r.p. generated by the OBU within a single side band

EIRPOBU e.i.r.p. generated by the OBU antenna
EIRPTSM e.i.r.p. referred to transmitter spectrum mask
ΔfRSU Frequency error of RSU
Δfs Sub-carrier frequency error
f Frequency
fc Centre frequency of receiving device or of MSS2 used for calibration
FER Frame error ratio
fObuTx Actual centre frequency of the lower and upper side band of the OBU uplink channel
fMSS1 Frequency of MSS1
foffset Offset frequency
fs Nominal OBU sub-carrier frequency
fTx Nominal RSU carrier frequency
fTx,actual Actual centre frequency of the downlink carrier
fu Nominal centre frequency of unwanted signal
fu1, fu2 Centre frequencies of unwanted signal
Gc Conversion gain
Gcorr Correction gain
GOBU,Rx Gain of OBU receiving antenna
GOBU,Tx Gain of OBU transmitting antenna
GRSA Gain of receiving substitution antenna
GTA Gain of test antenna
GTSA Gain of transmitting substitution antenna
GRSU,Tx Gain of RSU transmitting antenna
k Expansion factor (coverage factor)
lg(.) Logarithm to the base ten
m Modulation index
N Total number of transmitted bits within a single frame
PCW Power of CW signal
PD11a Power limit for communication (upper)
PD11b Power limit for communication (lower)
Pinc Incident signal power as received by an ideal isotropical receiving antenna
Pinc,scan Incident signal power obtained from a scanning process
Pinc,dBm Pinc in dBm
PLHCP Signal power of left hand circular polarized wave
Pmax Maximum signal power
Pmod Power of modulated signal
PMMS1 Output signal power of MSS1
PMMS2 Output signal power of MSS2
PObuRx Incident signal power to OBU, referred to an ideal isotropical receiving antenna
Ppol Signal power of wave with corresponding polarization
Pv Signal power of wave featuring vertical polarization
Ph Signal power of wave featuring horizontal polarization
PPM1 Signal power measured by the power meter 1
Pref Reference signal power limit in Watt
Pref,dBm Reference signal power limit in dBm
PreTx Retransmitted signal power
PRSA Signal power obtained from receiving substitution antenna
PRHCP Signal power of right hand circular polarized wave
Pssb Signal power within single side band
Psens Declared sensitivity of receiver

ETSI
 12 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

Pspurious Signal power of spurious signal

Ptot Sum of signal power P1 + P2, or P1 + P2 + ... + P5, whichever applies
Ptot,dBm Ptot in dBm
PTSM Transmitter spectrum mask
Pu Power of unwanted signal at OBU antenna
Pu max Unwanted signal power limit at OBU antenna
Pw Signal power of wanted signal
P0 Reference signal power of 1 mW corresponding to 0 dBm
RBW Resolution bandwidth
TCW Duration of CW signal
Tmod Duration of modulated signal
Vmax, Vmin Maximal amplitude of modulated output signal of RSU caused by data bit 1, or 0
α Tilt angle of test antenna
αdisplace Displacement angle between TTA and RTA
θ Angle relative to OBU boresight indicating worst case direction
θ° Value of θ measured in degree
λ Wavelength
ρRSA Reflection coefficient at antenna connector of the receiving substitution antenna
ρTSA Reflection coefficient at antenna connector of the transmitting substitution antenna

3.3 Abbreviations
For the purposes of the present document the abbreviations given in CEN EN 12253 [3] and the following apply:

ASG Arbitrary Signal Generator

AT1 Attenuator 1
AT2 Attenuator 2
BER Bit Error Ratio
BLN Balun
BST Beacon Service Table
CA Corresponding Antenna
CC Coaxial Circulator
CRC Cyclic Redundancy Checking
CW Continuous Wave
DC Direct Current
DEC DECision
doa date of announcement
dop date of publication
dow date of withdrawal
DSRC Dedicated Short Range Communication
e.i.r.p. Equivalent Isotropically Radiated Power also called EIRP, eirp, E.I.R.P.
EC European Community
ECC European Community Commission
EFC Electronic Fee Collection
EUT Equipment Under Test
FCCA Ferrited Coaxial CAble
FCCA1 Ferrited Coaxial CAble 1
FER Frame Error Ratio
ISM Industrial, Scientific, Medical
LHCP Left Hand Circular Polarized
LOS Line-Of-Sight
LP Linear Polarized
Mc Location of the OBU antenna phase centre
Mcentre Centre point between phase centres of TTA and RTA
MSS1 Monochromatic Signal Source 1
MSS2 Monochromatic Signal Source 2
n.a. not applicable
OBU On Board Unit

ETSI
 13 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

PE Portable Equipment
PM1 Power Meter 1
ppm parts per million (10-6)
PSTN Public Switched Telephone Network
R&TTE Radio and Telecommunications Terminal Equipment
RBW Resolution BandWidth
RD Receiving Device
REC RECommendation
RF Radio Frequency
RRxA RSU Receiving Antenna
RSA Receiving Substitution Antenna
RSU Road Side Unit
RTA Receiving Test Antenna
RTTT Road Transport and Traffic Telematics
RTxA RSU Transmitting Antenna
Rx Receiver
SMS1 Signal or Message Source 1
SR Special Report
SSB Single Side Band
TA Test Antenna
TD Technical Document
TM1 Test Message 1
TS1 Test Signal 1
TS2 Test Signal 2
TSA Transmitting Substitution Antenna
TSM Transmitter Spectrum Mask
TTA Transmitting Test Antenna
Tx Transmitter
VBW Video BandWidth
VST Vehicle Service table
VSWR Voltage Standing Wave Ratio
XP Cross Polarized
XPD Cross-Polar Discrimination

4 Technical requirements specifications

4.1 Mechanical and electrical design
4.1.1 Units
The present document specifies the characteristics of On Board Units.

Transmitters and receivers may be individual or combination units; some units may be transmitter only, some units may
be receiver only and some units may combine transmitter and receiver functionalities.

4.1.2 Controls
Those controls which if maladjusted might increase the interference possibilities to and from the equipment shall only
be accessible by partial or complete disassembly of the device and requiring the use of tools.

4.1.3 OBU assemblies

The OBU as identically supplied for testing and usage by the end-user is a physical assembly which is located and
operated in or on the vehicle to either transmit or receive DSRC signals. The OBU e.g. may be assembled such that it is:

• mountable in or on any part of the vehicle structure by the end-user according to guidelines in the user-manual,
and optionally removable after proper installation, or

• bonded to a part of the vehicle by a service station being authorized by the manufacturer, or

• an integral part of a vehicle component, such as a windscreen, bumper or licence plate.

ETSI
 14 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

In case the OBU is removable from its mounting device by the end-user, tests shall be performed with the OBU
properly attached to its mounting device.

The manufacturer shall declare the physical assembly of the OBU.

4.2 General characteristics

4.2.1 OBU sets
There exist two sets of OBUs called Set A and Set B which differ by the following parameters either in terms of value
or applicability, and which are defined in CEN EN 13372 [13].

Table 2: Differences in OBU Sets

CEN EN 12253 [3] Set A Set B

parameter abbreviation
D11a Power limit for communication (upper)
D12 n.a. Cut off power level of OBU
U4a Maximum SSB e.i.r.p. (boresight)
U4b n.a. Maximum SSB e.i.r.p. (35°)
U12b n.a. Conversion gain (upper limit)

The manufacturer shall declare which Set the unit complies with.

4.2.2 Uplink sub-carrier frequencies

The sub-carrier signal or sub-carrier is a signal whose nominal single frequency fs can vary within a range specified by
the sub-carrier frequency tolerance and which shall be capable of being modulated by a second, symbol-carrying signal,
see clause 4.2.4.

The uplink sub-carrier frequency is referred to as parameter U1 of CEN EN 12253 [3].

Every DSRC OBU shall support the two sub-carrier frequencies fs of 1,5 MHz and 2,0 MHz.

4.2.3 Carrier frequencies

According to parameter D3 in CEN EN 12253 [3] every OBU shall be able to operate in all DSRC channels as indicated
in table 3.

For tests of OBU parameters described in the present document, only the carrier frequencies fTx defined for channel 1
and channel 4 in table 3 shall be considered.

Table 3: Frequency bands and centre frequencies fTx allocated for DSRC

Pan European Service Frequencies National Service Frequencies

Channel 1 5,795 GHz to 5,800 GHz, fTx = 5,7975 GHz
Channel 2 5,800 GHz to 5,805 GHz, fTx = 5,8025 GHz
Channel 3 5,805 GHz to 5,810 GHz, fTx = 5,8075 GHz
Channel 4 5,810 GHz to 5,815 GHz, fTx = 5,8125 GHz

4.2.4 Modulation
The uplink sub-carrier, see clause 4.2.2, shall be modulated according to parameters U1b, U6, U6b and U6c in CEN
EN 12253 [3]. The modulated uplink sub-carrier then shall be used to modulate the carrier at frequency fTx received
from a RSU, i.e. the modulated sub-carrier shall be multiplied with the received carrier.

ETSI
 15 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

4.3 Environmental conditions

4.3.1 Environmental profile
The technical requirements of the present document apply under the environmental profile for operation of the
equipment, which shall be declared by the manufacturer. The equipment shall comply with all the technical
requirements of the present document at all times when operating within the boundary limits of the declared operational
environmental profile.

Recommended environmental profile parameters are summarized in annex C.

4.3.2 Power supply

All the characteristics and essential requirements applying to OBUs shall be fulfilled within the range of all declared
operational conditions of the power supply.

Power supply may be e.g. a built in battery, an external battery or a stabilized power supply.

NOTE: If an OBU is supplied by the battery of a vehicle, e.g. car or truck, the automotive
Directive 95/54/EC [i.4] applies.

4.4 Conformance requirements

4.4.1 Transmitter parameters
[Link] General
When the transmitter is properly installed, maintained and used for its intended purpose, it generates radio wave
emissions that do not create harmful interference, while unwanted radio wave emissions generated by the transmitter
(e.g. in adjacent channels) with a potential negative impact on the goals of radio spectrum policy are limited to such a
level that, according to the state of the art, harmful interference is avoided (Directive 2014/53/EU [i.5]).

[Link] Transmitter spectrum mask

The OBU transmitter spectrum mask (TSM) is the maximum e.i.r.p. allowed to be transmitted by the OBU within
specified frequency bands. The frequency bands are defined by their centre frequencies and bandwidths according to
table 4 considering carrier frequencies fTx in accordance with clause 4.2.3.

The OBU TSM is referred to as parameter U2 in CEN EN 12253 [3].

Table 4: OBU TSM upper limits

Measurement fTx ± 1,5 MHz, fTx ± 2 MHz, fTx ± 3 MHz, fTx ± 3,5 MHz, fTx ± 6,5 MHz, and
centre frequency f ± 7 MHz
Tx
(see note)
Bandwidth 500 kHz
Limit (e.i.r.p.) Set A: -39 dBm
Set B: -35 dBm
NOTE: Measurement shall not be performed at the used sub-carrier frequency, i.e. 1,5 MHz
or 2 MHz.

The maximum e.i.r.p. shall not exceed the limit as stated in table 4.

[Link] Maximum equivalent isotropically radiated power

The OBU maximum SSB equivalent isotropically radiated power EIRPMaxObuTx is the e.i.r.p. of the OBU in a single
side band measured within the valid range of incident signal power PD11a according table 12 and PD11b = -43 dBm,
according to parameter D11b of CEN EN 12253 [3]. The maximum e.i.r.p. shall not exceed the limits stated in table 5.

ETSI
 16 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

Table 5: Limits for OBU maximum SSB e.i.r.p.

Limits for OBU maximum SSB e.i.r.p.

CEN Set A Set B
Parameter U4b U4a U4b U4a
Direction (35°) boresight (35°) boresight
(see note) (see note)
Value (e.i.r.p.) n.a. -21 dBm -17 dBm -14 dBm
NOTE: 35° denotes the opening angle θ of a cone symmetrically around
boresight, see figure 1.

[Link] Transmitter frequency error

The relative sub-carrier frequency error Δfs of the OBU is defined by:

f ObuTx − f Tx, actual

Δf s = −1,
fs

where fObuTx is, respectively, the actual centre frequency of the lower and upper side band of the OBU uplink
channel, fTx,actual is the actual centre frequency of the downlink carrier, and fs is the nominal sub-carrier
frequency.

The sub-carrier frequency error is referred to as parameter U1a in CEN EN 12253 [3].

The absolute value |Δfs | of the relative OBU sub-carrier frequency error Δfs shall not exceed 0,1 %.

[Link] Transmitter unwanted emissions

When the OBU is in operating mode (i.e. transmitting a modulated signal), the e.i.r.p. of any unwanted emissions,
i.e. spurious or out-of-band emission, shall not exceed the limits presented in table 6.

Measurements shall not be performed within an exclusion band of ±2,5 times the DSRC channel spacing of 5 MHz,
i.e. ± 12,5 MHz around the RSU carrier frequency fTx under test.

Table 6: Limits of unwanted emissions as specified in CEPT/ERC

Recommendation 74-01E [10] for transmitters

Limits Reference
Mode Frequency bands Type of emission
(e.i.r.p.) bandwidth
47 MHz to 74 MHz
87,5 MHz to 118 MHz
-54 dBm 100 kHz
174 MHz to 230 MHz
Operating 470 MHz to 862 MHz Spurious and
Other frequencies out-of-band emissions
-36 dBm 100 kHz
> 30 MHz and ≤ 1 GHz
Frequencies > 1 GHz and < 26 GHz
-30 dBm 1 MHz
outside the exclusion band

4.4.2 Receiver parameters

[Link] General
The receiver parameters allow the OBU to operate as intended and protect it against the risk of harmful interference, in
particular from shared or adjacent channels, and, in so doing, supports improvements in the efficient use of shared or
adjacent channels (Directive 2014/53/EU [i.5]).

Although receivers do not themselves cause harmful interference, reception capabilities are an increasingly important
factor in ensuring the efficient use of radio spectrum by way of an increased resilience of receivers against harmful
interference and unwanted signals on the basis of the relevant essential requirements of Union harmonisation legislation
(Directive 2014/53/EU [i.5]).

ETSI
 17 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

[Link] Receiver unwanted emissions in the spurious domain

The e.i.r.p. of any spurious emission when the OBU is in stand-by mode shall not exceed the limits presented in table 7.
Stand-by mode is a mode, in which the OBU never transmits.

Measurements shall not be performed within an exclusion band of ±2,5 times the DSRC channel spacing of 5 MHz,
i.e. ± 12,5 MHz around the RSU carrier frequency fTx under test.

Table 7: Limits of unwanted emissions as specified in CEPT/ERC

Recommendation 74-01E [10] for receivers

Mode Frequency bands Limits Reference Type of emission

(e.i.r.p.) bandwidth
Stand-by Other frequencies -57 dBm 100 kHz Spurious emissions
> 30 MHz and ≤ 1 GHz
Frequencies > 1 GHz and < 26 GHz -47 dBm 1 MHz
outside the exclusion band

[Link] Sensitivity
The OBU sensitivity is the minimum incident power Psens referred to a loss-less isotropic antenna at the location of the
OBU receive antenna that allows the OBU to receive DSRC frames with a BER of 10-6 or smaller. This applies for all
orientations of the OBU receive antenna within a cone of opening angle θ according to figure 1, denoted as worst case
direction, around boresight.

The OBU sensitivity Psens and the worst case direction shall be declared by the manufacturer.

Additionally,

Psens ≤ PD11b = -43 dBm

shall apply.

If the manufacturer does not declare the worst case direction, then the sensitivity requirement shall apply for θ = 35°. In
this case, measurements shall be performed at the directions indicated by M0, M1, M2, M3, and M4, see figure 1.

[Link] Receiver selectivity

[Link].1 General
The manufacturer shall declare one of the OBU receiver selectivity classes specified in table 8 and table 9.

[Link].2 Receiver spurious response rejection

The spurious response rejection is a measure of the capability of the receiver to receive a wanted signal without
exceeding a given degradation due to the presence of an unwanted input signal at any frequency which differs in
frequency from the wanted signal by at least 20 MHz.

The unwanted signal is considered to be an unmodulated carrier. The received wanted DSRC incident power level at the
phase centre of the OBU antenna (see clause 4.4.3) is considered to be -37 dBm (6 dB above the OBU sensitivity level).
For these considerations the power limit at the phase centre of the OBU antenna that does not degrade the BER to a
value greater than 10-6 shall conform to the limit given in table 8 for the selected OBU receiver selectivity class.

Table 8: Receiver spurious response rejection

OBU receiver selectivity class Receiver spurious response rejection

Class 1 -45 dBm
Class 2 -40 dBm

ETSI
 18 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

[Link].3 Receiver blocking

The receiver blocking is a measure of the capability of the receiver to receive a wanted signal without exceeding a given
degradation due to the presence of an unwanted input signal at any frequency which differs in frequency from the
wanted signal by at least 50 MHz.

The unwanted signal is considered to be an unmodulated carrier which differs in frequency from the wanted signal by
± 50 MHz, ± 100 MHz , and ± 200 MHz.

The received wanted DSRC incident power level at the phase centre of the OBU antenna (see clause 4.4.3) is
considered to be -37 dBm (6 dB above the OBU sensitivity level). For these considerations the power limit at the phase
centre of the OBU antenna that does not degrade the BER to a value greater than 10-6 shall conform to the limit given in
table 9 for the selected OBU receiver selectivity class.

Table 9: Receiver blocking

OBU receiver selectivity class Receiver blocking

Class 1 -35 dBm
Class 2 -30 dBm

4.4.3 Antennas
All equipment antennas shall be LHCP according to parameters U5 and U5a in CEN EN 12253 [3].

An OBU may provide either none, one or more antenna connectors.

In case an OBU does not provide an antenna connector, then either one antenna for receiving and transmitting, or one
antenna for receiving and one antenna for transmitting are implemented. In the first case, the phase centre of the OBU
antenna is entitled Mc, see figure 1. In the latter case it is assumed that the two antennas are close to each other and
point approximately to the same direction. The centre between these two antennas then is entitled Mc. For the purpose
of easy reading of the present document, in what follows Mc is referred to as "phase centre of the OBU antenna".

The minimum operational direction of OBU receive and transmit antenna is characterized by a cone with opening
angle θ around boresight as depicted in figure 1. The OBU shall provide specific properties inside the cone. The border
of the cone itself is referred to as worst case direction. The directions M0 through M4 and the phase centre Mc of the
OBU antenna are related to measurements described in the present document.

y
z

M2
Mc

M1
M0
θ

θ
M3

M4 bor
esi
ght
x

Figure 1: OBU antenna characteristic

The angle θ is used in different tests of the present document.

A value of θ = 35° is required for OBU minimum conversion gain and for OBU maximum single side band e.i.r.p.
according to CEN EN 12253 [3].

ETSI
 19 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

For other properties of the OBU, e.g. sensitivity, the manufacturer may declare an opening angle θ other than 35° of the
cone.

5 Testing for compliance with technical requirements

5.1 Environmental conditions for testing
Tests defined in the present document shall be carried out at representative points within the boundary limits of the
declared operational environmental profile.

Where technical performance varies subject to environmental conditions, tests shall be carried out under a sufficient
variety of environmental conditions declared by the manufacturer (within the boundary limits of the declared
operational environmental profile) to give confidence of compliance for the affected technical requirements.

A possible manufacturer declaration can be based on the extreme categories I, II, III as defined in clause C.3.

5.2 Interpretation of the measurement results

The interpretation of the results recorded in a test report for the measurements described in the present document shall
be as follows:

• the measured value related to the corresponding limit will be used to decide whether an equipment meets the
requirements of the present document;

• the value of the measurement uncertainty for the measurement of each parameter shall be included in the test
report;

• the recorded value of the measurement uncertainty shall be, for each measurement, equal to or lower than the
figures in table 10.

For the test methods, according to the present document, the measurement uncertainty figures shall be calculated and
shall correspond to an expansion factor (coverage factor) k = 1,96 or k = 2 (which provide confidence levels of
respectively 95 % and 95,45 % in the case where the distributions characterizing the actual measurement uncertainties
are normal (Gaussian)). Principles for the calculation of measurement uncertainty are contained in ETSI
TR 100 028 [4], in particular in annex D of the ETSI TR 100 028-2 [4].

Table 10 is based on such expansion factors.

Table 10: Absolute measurement uncertainty

Parameter Uncertainty
RF power (conducted) ± 4 dB
RF frequency, relative ± 1 x 10-7
Radiated emission of transmitter, valid to 40 GHz ± 6 dB
Adjacent channel power ± 5 dB
Sensitivity ± 5 dB
Two and three signal measurements ± 4 dB
Two and three signal measurements using radiated fields ± 6 dB
Radiated emission of receiver, valid to 40 GHz ± 6 dB
Temperature ±1K
Relative humidity ±5%

5.3 Essential radio test suites

5.3.1 Transmitter parameters
[Link] Transmitter spectrum mask
[Link].1 General
This test shall be performed either with radiated or conducted measurements.

ETSI
 20 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

Basic requirements, test setups, and guidelines for measurements are provided in annex B.

Parameter descriptions and limits are provided in clause [Link].

For this test, the incident signal power Pinc shall be adjusted such that the power measured in the test is maximized.
A suitable value for Pinc is the value Pinc,scan as evaluated in clause [Link].

The centre frequencies fc = fTx + foffset and the resolution bandwidth RBW of the RD shall be set for measurements in
the sequence as indicated for the offset frequencies foffset in table 11.

Table 11: Offset frequencies and RBW for testing OBU Tx spectrum mask

foffset (MHz) -1 +1 -1,5 +1,5 -2 +2 -3 +3 -3,5 +3,5 -4 +4 -6,5 +6,5 -7 +7

RBW 30 kHz 100 kHz 30 kHz 100 kHz

[Link].2 Radiated measurements

The test procedure is as follows:

1) Prepare the test site according to clause B.[Link].

2) Switch on the monochromatic output signal of the MSS1, tune it to the carrier frequency fTx defined for
channel 1 according to table 3 and clause 4.2.3.

3) Adjust the output power of the MSS1 such that the power PRSA measured by the power meter PM1 amounts
to:

2⎞
PRSA = Pinc × G RSA × ⎛⎜ 1 − ρ RSA ⎟,
⎝ ⎠

where Pinc, and ρRSA denote, respectively, the incident signal power as requested in clause [Link].1, and the
reflection coefficient at the connector of the RSA.

4) Replace the RSA by the OBU under test such that its phase centre Mc is as coincident with the axis of rotation
of the turntable as possible. If the phase centre Mc of the OBU is unknown and no antenna is visible, the
volume centre of the OBU shall be used instead. The boresight of the OBU antenna shall point towards the
phase centre of the TA.

5) Set the RD to its CW mode, also called zero span mode of operation, where the instrument is not sweeping
across a frequency band.

6) The OBU under test shall be operated with sub-carrier frequency fs in a test mode such that it transmits the test
signal TS1.

7) Select one of the offset frequencies foffset from table 11. An absolute value of the offset frequency equal to the
value of the actually used sub-carrier frequency fs, e.g. foffset = ±1,5 MHz or foffset = ±2,0 MHz, is invalid for
this test. If foffset amounts to either ±1 MHz or ±4 MHz, proceed with step 8, otherwise proceed with step 13.

8) Set the centre frequency fc of the RD to fc = fTx + foffset – RBW / 2 and select RBW according to table 11.

9) Measure the signal power P1 from the RD and report this value together with the associated carrier frequency
fTx and offset frequency foffset.

10) Set the centre frequency fc of the RD to fc = fTx + foffset + RBW / 2 and select RBW according to table 11.

11) Measure the signal power P2 from the RD and report this value together with the associated carrier frequency
fTx and offset frequency foffset.

ETSI
 21 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

12) Determine the total signal power Ptot by summing up the two signal power values as Ptot = P1 + P2, and
compute the power Ptot,dBm in dBm as Ptot,dBm = 10 × lg(Ptot P0 ) . Report this value together with the
associated carrier frequency fTx and offset frequency foffset. Proceed with step 19.

13) Set the centre frequency fc of the RD to its initial value fc = fTx + foffset – 2 × RBW, select RBW according to
table 11 and set the counter i = 1.

14) Measure the signal power Pi from the RD and report this value together with the associated carrier frequency
fTx and offset frequency foffset.

15) Increase the value of the counter by 1. When the counter equals 6, proceed with step 18, otherwise proceed
with step 16.

16) Increase the centre frequency fc of the RD by RBW and measure the signal power Pi from the RD and record
its value together with the associated carrier frequency fTx and offset frequency foffset in the test report.

17) Repeat step 15 and step 16.

18) Determine the total signal power Ptot by summing up five signal power values as Ptot = P1 + P2 + P3 + P4 + P5
and compute the total power Ptot,dBm in dBm as Ptot,dBm = 10 × lg(Ptot P0 ) . Report this value together with
the associated carrier frequency fTx and offset frequency foffset.

19) Repeat step 7 to step 19 until the whole sequence of offset frequencies listed in table 11 have been processed.

20) Repeat step 7 to step 19 once for the other sub-carrier frequency fs.

21) Repeat step 1 to step 20 for the carrier frequency fTx defined for channel 4 according to table 3 and
clause 4.2.3.

22) For a specific combination of carrier frequency fTx and offset frequency foffset the maximum value of all Ptot
reported for different sub-carrier frequencies fs shall apply for the subsequent evaluation.

23) Replace the OBU under test by a LHCP calibrated TSA of gain GTSA and reflection coefficient ρTSA at its
connector suited for the range of carrier frequencies fTx listed in table 3 in such a way that its phase centre
coincides with the one of the OBU transmitting antenna. If the measurement arrangement with one test
antenna is used, the boresight of the TSA shall point towards the phase centre of the TTA. If the measurement
arrangement with two test antennas is used, boresight of the TSA shall point towards position Mcentre.

24) Connect the output of the TSA via the optional balun BLN, if required, of feed through attenuation ATNBLN,
and the calibrated FCCA1 of feed through attenuation ATNCA1 to a calibrated MSS2.

25) Tune the frequency of the MSS2's output signal to the same frequency fc = fTx + foffset as was used for the RD,
where fTx is according to clause 4.2.3 and foffset shall be according to table 11.

26) Rotate the TSA through 360° until the maximum level is detected by the RD.

27) Adjust the output signal level PMSS2 of the MSS2 until the level, measured on the RD, becomes identical to
Ptot as reported in step 22 at the same combination of carrier frequency fTx and offset frequency foffset. This
output signal level PMSS2 from the MSS2 shall be reported together with the associated carrier frequency fTx
and offset frequency foffset.

28) Repeat step 25 to step 27 for all remaining combinations of carrier frequencies fTx and offset frequencies
foffset.

29) The TSM at this combination of carrier frequency fTx and offset frequency foffset, expressed as an e.i.r.p. of the
OBU under test shall be calculated by:

ETSI
 22 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

PMSS2 × GTSA × ⎛⎜ 1 − ρ TSA

2⎞
⎟
⎝ ⎠
EIRPTSM = ,
ATN CA1 × ATN BLN

where all the parameters in the above formula are related to the corresponding measurement frequencies. The
result shall be reported together with the associated carrier frequency fTx and offset frequency foffset. It shall
not exceed the limit stated in clause [Link].

[Link].3 Conducted measurements

The test procedure is as follows:

1) Prepare the test site according to clause B.[Link].

2) Tune the frequency of the MSS1's output signal to the carrier frequency fTx defined for channel 1 according to
table 3 and clause 4.2.3.

3) Replace the OBU under test by a power meter PM1.

4) Adjust the output power of the MSS1 such that the power measured by PM1 matches the incident power as
indicated in clause [Link].1 increased by the gain of the OBU receive antenna as declared by the
manufacturer.

5) Replace PM1 by the OBU under test.

6) Set the RD to its CW mode, also called zero span mode of operation, where the instrument is not sweeping
across a frequency band.

7) The OBU under test shall be operated with sub-carrier frequency fs in a test mode such that it transmits the test
signal TS1.

8) Select one of the offset frequencies foffset from table 11. An absolute value of the offset frequency equal to the
value of the actually used sub-carrier frequency fs, e.g. foffset = ±1,5 MHz or foffset = ±2,0 MHz, is invalid for
this test. If foffset amounts to either ±1 MHz or ±4 MHz, proceed with step 9, otherwise proceed with step 14.

9) Set the centre frequency fc of the RD to fc = fTx + foffset – RBW / 2 and select RBW according to table 11.

10) Measure the signal power P1 from the RD taking into account all losses the signal suffers between the output
connector of the OBU under test and the input connector of the RD and report this value together with the
associated carrier frequency fTx and offset frequency foffset.

11) Set the centre frequency fc of the RD to fc = fTx + foffset + RBW / 2 and select RBW according to table 11.

12) Measure the signal power P2 from the RD taking into account all losses the signal suffers between the output
connector of the OBU under test and the input connector of the RD and report this value together with the
associated carrier frequency fTx and offset frequency foffset.

13) Determine the total signal power Ptot by summing up the two signal power values as Ptot = P1 + P2, and
compute the power Ptot,dBm in dBm as Ptot,dBm = 10 × lg(Ptot P0 ) . Report this value together with the
associated carrier frequency fTx and offset frequency foffset. Proceed with step 20.

14) Set the centre frequency fc of the RD to its initial value fc = fTx + foffset – 2 × RBW, select RBW according to
table 11 and set the counter i = 1.

15) Rotate the OBU under test through 360° in the horizontal plane until signal power detected by the RD reaches
its maximum value Pi. Record this value together with the associated carrier frequency fTx and offset
frequency foffset in the test report.

16) Increase the value of the counter by 1. When the counter equals 6, proceed with step 19, otherwise proceed
with step 17.

ETSI
 23 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

17) Increase the centre frequency fc of the RD by RBW and measure the signal power Pi from the RD and record
its value together with the associated carrier frequency fTx and offset frequency foffset in the test report.

18) Repeat step 16 and step17.

19) Determine the total signal power Ptot by summing up five signal power values as Ptot = P1 + P2 + P3 + P4 + P5
and compute the total power Ptot,dBm in dBm as Ptot,dBm = 10 × lg(Ptot P0 ) . Report this value together with
the associated carrier frequency fTx and offset frequency foffset.

20) Repeat step 8 to step 19 until the whole sequence of offset frequencies listed in table 11 have been processed.

21) Repeat step 8 to step 20 once for the other sub-carrier frequency fs.

22) Repeat step 1 to step 21 for the carrier frequency fTx defined for channel 4 according to table 3 and
clause 4.2.3.

23) For a specific combination of carrier frequency fTx and offset frequency foffset the maximum value of all Ptot
reported for different sub-carrier frequencies fs shall apply for the subsequent evaluation.

24) Compute the signal power PTSM associated with each carrier frequency fTx and each offset frequency foffset
from the corresponding signal power values Ptot considering all losses within the signal path between the RD
and the connector of the OBU's transmitting antenna. Record all values of PTSM together with the associated
carrier frequency fTx and offset frequency foffset in the test report.

25) The TSM for each combination of carrier frequency fTx and offset frequency foffset, expressed as an e.i.r.p. of
the OBU under test shall be calculated by:

EIRPTSM = PTSM × GOBU,Tx

where GOBU,Tx denotes the maximum gain of the OBU transmitting antenna. It shall be understood that all
parameter values are taken at the corresponding frequency f = fTx + foffset. The result shall be reported together
with the associated carrier frequency fTx and offset frequency foffset. None of these values shall exceed the
limit stated in clause [Link].

[Link] Maximum equivalent isotropically radiated power

[Link].1 General
This test shall be performed either with radiated or conducted measurements.

Basic requirements, test setups, and guidelines for measurements are provided in annex B.

Parameter descriptions and limits are provided in clause [Link].

Measurement shall be conducted with the reference incident power Pinc set equal to the maximum incident signal power
PD11a according to parameter D11a of CEN EN 12253 [3], see table 12.

In order to identify the incident signal power Pinc at which maximum e.i.r.p. occurs, a scanning procedure shall be
performed. The measurement shall be repeated at this value Pinc = Pinc,scan of the incident signal power and the result
shall be reported together with this incident signal power.

The conversion gain shall be adjusted to the maximum possible value, if applicable.

Table 12: OBU power limit for communication (upper) for Sets A and B

Power limit for communication (upper) PD11a

according to parameter D11a of CEN EN 12253 [3]
Set A Set B
-17 dBm -24 dBm

ETSI
 24 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

[Link].2 Radiated measurement

The test procedure is as follows:

1) Prepare the test site according to clause B.[Link]. The initial alignment of the OBU under test as needed in
step 4 shall be according to M0 in figure 1, i.e. the boresight of the OBU antenna shall point towards the phase
centre of the TA.

2) Switch on the monochromatic output signal of the MSS1, tune it to the carrier frequency fTx defined for
channel 1 according to table 3 and clause 4.2.3.

3) Adjust the output power of the MSS1 such that the power PRSA measured by the power meter PM1 amounts
to:

2⎞
PRSA = Pinc × G RSA × ⎛⎜ 1 − ρ RSA ⎟,
⎝ ⎠

where Pinc, and ρRSA denote, respectively, the reference incident signal power as requested in table 12, and the
reflection coefficient at the connector of the RSA.

4) Replace the RSA by the OBU under test such that its phase centre Mc is as coincident with the axis of rotation
of the turntable as possible. If the phase centre Mc of the OBU under test is unknown and no antenna is
visible, the volume centre of the OBU under test shall be used instead. Align the OBU's boresight as required.

5) Set the OBU under test to a test mode such that it re-transmits test signal TS2 with sub-carrier frequency fs.

6) Measure the larger of the power levels Pmax within the two side bands by the RD using a RBW of 100 kHz
and report this value of Pmax together with the orientation of the OBU under test Mi, i = [0..4], and the values
of fs and fTx.

7) Repeat step 6 for the other value of the sub-carrier frequency fs.

8) Repeat step 3 to step 7 for the carrier frequency fTx defined for channel 4 according to table 3 and clause 4.2.3.

9) In case of a Set B OBU under test proceed with step 10, otherwise continue with step 11.

10) Repeat step 1 to step 8 for all remaining OBU orientations as indicated by M1, M2, M3, and M4 in figure 1 in
order to measure the CEN parameter U4a.

11) Replace the OBU under test by a LHCP calibrated TSA of gain GTSA and reflection coefficient ρTSA at its
connector suited for the range of carrier frequencies fTx listed in table 3 in such a way that its phase centre
coincides with the one of the OBU transmitting antenna. If the measurement arrangement with one test
antenna is used, the boresight of the TSA shall point towards the phase centre of the TTA. If the measurement
arrangement with two test antennas is used, boresight of the TSA shall point towards position Mcentre.

12) Connect the output of the TSA via the optional balun BLN, if required, of feed through attenuation ATNBLN,
and the calibrated, FCCA1 of feed through attenuation ATNCA1 to a calibrated MSS2 that shall be tuned to the
frequency which is the sum of the carrier frequency fTx and the (signed) sub-carrier frequency fs reported as a
set together with the OBU orientation in step 6.

13) Adjust the output signal level of the MSS2 until the level, measured on the RD, becomes identical to Pmax
recorded in step 6 for this set of values of fTx, fs and Mi. This output signal level PMSS2 from the MSS2 shall
be reported.

14) The e.i.r.p. of the OBU under test shall be calculated by:

PMSS2 × GTSA × ⎛⎜ 1 − ρ TSA

2⎞
⎟
⎝ ⎠
EIRPOBU = ,
ATN CA1 × ATN BLN

ETSI
 25 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

where all the parameters in the above formula are related to the corresponding measurement frequencies. The
result shall not exceed the limit stated in table 5.

15) Repeat step 12 to step 14 for all remaining sets of values of fTx, fs and Mi.

[Link].3 Conducted measurement

The test procedure is as follows:

1) Prepare the test site according to clause B.[Link].

2) Tune the frequency of the MSS1's output signal to the carrier frequencies fTx defined for channel 1 according
to table 3 and clause 4.2.3.

3) Replace the OBU under test receiver by a power meter PM1.

4) Adjust the output power of the MSS1 such that the power measured by PM1 matches the reference incident
power as indicated in table 12 increased by the gain of the OBU receive antenna as declared by the
manufacturer.

5) Replace PM1 by the OBU under test.

6) Set the OBU under test to a test mode such that it re-transmits test signal TS2 with sub-carrier frequency fs.

7) Measure the signal power within each of the two side bands by the RD using a RBW of 100 kHz and compute
the corresponding signal power at the connector of the OBU's transmitting antenna taking into account all
losses the signal suffers between the output connector of the OBU under test and the input connector of the
RD. Report the larger of these two values, the power Pmax.

8) Repeat step 7 for the other sub-carrier frequency.

9) Repeat step 3 to step 8 for the carrier frequency fTx defined for channel 4 according to table 3 and clause 4.2.3.

10) Compute the corresponding e.i.r.p. for all the power levels Pmax recorded within step 7 into the test report
using the equation:

EIRPOBU = Pmax × GOBU,Tx(Mi)

where GOBU,Tx(Mi) denotes the gain of the OBU transmitting antenna in the directions M0 through M5 as
indicated in figure 1. None of the results shall exceed the limit stated in table 5. In case of a Set A OBU under
test only direction M0 is applicable.

[Link] Transmitter frequency error

[Link].1 General
This test shall be performed either with radiated or conducted measurements.

Basic requirements, test setups, and guidelines for measurements are provided in annex B.

Parameter descriptions and limits are provided in clause [Link].

[Link].2 Radiated measurements

The test procedure is as follows:

1) Prepare the test site according to clause B.[Link].

2) Switch on the monochromatic output signal of the MSS1, tune it to the carrier frequencies fTx defined for
channel 1 according to table 3 and clause 4.2.3 and adjust its output power to a level that produces an incident
power at the location of the CA within the dynamic range of the OBU under test.

ETSI
 26 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

3) Replace the RSA by the OBU under test such that its phase centre Mc is as coincident with the axis of rotation
of the turntable as possible. If the phase centre Mc of the OBU under test is unknown and no antenna is
visible, the volume centre of the OBU under test shall be used instead. The boresight of the OBU antenna shall
point towards the phase centre of the TA.

4) Set the RBW of the RD used for frequency measurements to ≤ 1 kHz.

5) Set the OBU under test to a test mode with test signal TS2 and with sub-carrier frequency fs.

6) Connect temporarily the output of the MSS1 to the RD and measure and report the actual carrier frequency
fTx,actual of the downlink radio signal. Reconnect the output of the MSS1.

7) Measure with the RD the actual centre frequency fObuTx of the uplink radio signal in one of the two side bands
as convenient.

f ObuTx − f Tx, actual

8) Calculate the actual sub-carrier frequency error Δf s = − 1 and convert the value to percent.
fs
The actual value shall not exceed the limit stated in clause [Link].

9) Repeat step 6 to step 8 for the other sub-carrier frequency fs.

[Link].3 Conducted measurements

The test procedure is as follows:

1) Prepare the test site according to clause B.[Link].

2) Tune the frequency of the MSS1's output signal to the carrier frequencies fTx defined for channel 1 according
to table 3 and clause 4.2.3.

3) Replace the OBU under test by a power meter PM1.

4) Adjust the output power of the MSS1 such that the power measured by PM1 is within the dynamic range of the
OBU under test reduced by the gain of the OBU receive antenna as declared by the manufacturer.

5) Replace PM1 by the OBU under test.

6) Set the RBW of the RD used for frequency measurements to ≤ 1 kHz.

7) Set the OBU under test to a test mode with test signal TS2 and with sub-carrier frequency fs.

8) Connect temporarily the output of the MSS1 to the RD and measure and report the actual carrier frequency
fTx,actual of the downlink radio signal. Reconnect the output of the MSS1.

9) Measure with the RD the actual centre frequency fObuTx of the uplink radio signal in one of the two side bands
as convenient.

f ObuTx − f Tx, actual

10) Calculate the actual sub-carrier frequency error Δf s = − 1 and convert the value to percent.
fs
The actual value shall not exceed the limit stated in clause [Link].

11) Repeat step 8 to step 11 for the other sub-carrier frequency fs.

[Link] Transmitter unwanted emissions

[Link].1 General
The test shall be performed either in an anechoic chamber or in an open area test site. The setup is illustrated in
clause B.[Link] in figure B.11 and figure B.12.

The test shall be performed with radiated measurements within all frequency bands as referred to as "operating mode"
in table 6 outside the exclusion band stated in clause [Link].

ETSI
 27 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

Basic requirements, test setups, and guidelines for measurements are provided in annex B.

Parameter descriptions and limits are provided in clause [Link].

For this test, the incident signal power Pinc shall be adjusted such that the measured power level at the RTA is at its
maximum. A suitable value for Pinc is the value Pinc,scan as evaluated in clause [Link].

[Link].2 Radiated measurement

With reference to figure B.11 and figure B.12 in clause B.[Link], the following test procedure shall apply for
simultaneous spurious and out-of-band emissions radiated by the OBU transmit antenna.

1) The test shall be setup as specified in clause B.[Link].

2) Replace the OBU under test by the TSA such that their phase centres, and boresights coincide, respectively.
Boresight of the TSA shall point towards the phase centre of the RTA. The TSA shall be connected to a
calibrated MSS2 using calibrated, ferrited coaxial cables. Polarization of the TSA shall match the one of the
RTA.

3) Move the turntable to its initial angular position MT0 according to figure B.12.

4) Table 6 in clause [Link] specifies the maximum spurious and out-of-band emissions for the operating mode as
function of frequency. Adjust the output power of the MSS2 such that the e.i.r.p. of the TSA is equal to these
limits for each measurement frequency and measure the power at the RD with a RBW equal to the reference
bandwidth as indicated in table 6. Report the power levels as a function of frequency in Watt measured at the
RD for further usage as a limit line.

5) The TTA shall be connected to a calibrated MSS1 using calibrated, FCCA.

6) Switch on the monochromatic output signal of the MSS1, tune it to the carrier frequency fTx defined for
channel 1 according to table 3 and clause 4.2.3.

7) The LHCP RSA of gain GRSA shall be suited for the range of carrier frequencies fTx listed in table 3. Replace
the TSA by the LHCP RSA such that their phase centres, and boresights coincide, respectively. The output of
the RSA shall be connected directly to the power sensor of power meter PM1 that shall be calibrated to the
frequency of the monochromatic signal under consideration. Adjust the output power of the MSS1 such that
the power PRSA measured by the power meter PM1 amounts to:

2⎞
PRSA = Pinc × G RSA × ⎛⎜ 1 − ρ RSA ⎟,
⎝ ⎠

where Pinc, and ρRSA denote, respectively, the incident signal power as requested in clause [Link].1, and the
reflection coefficient at the connector of the RSA.

8) Repeat step 1, which actually replaces the RSA by the OBU under test.

9) Select the first frequency band to be tested according to table 6.

10) Set the OBU under test to a test mode with test signal TS1 and with sub-carrier frequency fs.

11) Move the turntable to its initial angular position MT0 according to figure B.12.

12) The resolution bandwidth of the RD used to measure signal power shall be set equal to the reference
bandwidth as indicated in table 6. Measure the power spectrum Ppol, i.e. Ppol = Pv in case of vertical polarized
RTA and Ppol = Ph in case of horizontal polarized RTA, received by the RD and report the result for further
processing in step 18. Repeat step 12 for all other angular positions MT1, MT2, MT3 of the turntable
according to figure B.12.

13) Repeat step 16 and step 17 once for the other sub-carrier frequency fs.

14) Repeat step 15 to step 18 for the carrier frequency fTx defined for channel 4 according to table 3 and
clause 4.2.3.

ETSI
 28 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

15) Repeat step 11 to step 14 for all frequency bands indicated in clause [Link], see there table 6 for the operating
mode of the OBU under test and the exclusion band.

16) Rotate the RTA such that it is horizontally polarized, without changing position of its phase centre and
boresight orientation.

17) Repeat step 11 to step 15.

18) Compute the resulting power Pspurious = Pv + Ph and compare it with the limit line. If the power Pspurious
exceeds the limit evaluated in step 9 for any frequency, the test failed.

5.3.2 Receiver parameters

[Link] Receiver unwanted emissions in the spurious domain
[Link].1 General
The test shall be performed with radiated measurements within all frequency bands as referred to as "stand-by state" in
table 7 outside the exclusion band stated in clause [Link]. Conducted measurements are not possible.

The test shall be performed either in an anechoic chamber or in an open area test site. The setup is illustrated in
figure B.11 and figure B.12 in clause B.[Link].

Basic requirements, test setups, and guidelines for measurements are provided in annex B.

Parameter descriptions and limits are provided in clause [Link].

[Link].2 Radiated measurement

With reference to figure B.11 and figure B.12, the test procedure for spurious and out-of-band emissions according to
clause [Link] shall apply with the following modifications:

1) There shall be no TTA and no MSS1. Thus statements on the carrier frequency fTx shall not apply.

2) There shall be no RSA.

3) The OBU under test shall never transmit. Thus statements on sub-carrier frequency fs shall not apply.

4) The OBU under test shall never be in the sleep mode.

5) The applicable limits and resolution band widths for the "stand-by mode" are indicated in table 7.

[Link] Sensitivity
[Link].1 General
This test shall be performed either with radiated or conducted measurements.

Basic requirements, test setups, and guidelines for measurements are provided in annex B.

Parameter descriptions and limits are provided in clause [Link].

The description below assumes that an OBU is used to receive down-link signals and to generate up-link signals, both
of type TM1. The test can be performed accordingly based on laboratory instruments, i.e. an RSU simulator, to generate
down-link signals of type TS1 and messages of type TM1 and to receive and evaluate up-link signals of type TM1.

NOTE: The manufacturer may extend the test in order to determine the actual value of the upper power limit for
communication.

[Link].2 Radiated measurements

The following procedural step shall apply:

1) Prepare the test site according to clause B.[Link].

ETSI
 29 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

2) If the provider declared a worst case direction, position the OBU such that this worst case direction points
towards the phase centre of the RTA.

3) Set the SMS1 such that it continuously transmits test signal TS1.

4) Set the carrier frequency fTx of SMS1 defined for channel 1 according to table 3 and clause 4.2.3.

5) Set the modulation index of the signal transmitted by the SMS1 to 0,5 or to the smallest possible value within
the allowed range of 0,5 to 0,9 supported by the SMS1.

6) Replace the OBU receiver by a RSA of gain GRSA such that their phase centres and boresights coincide.
Connect the RSA to a power meter PM1.

7) Adjust the output signal power of the SMS1 such that the signal power indicated by the power meter PM1
amounts to:

2⎞
PRSA = Pref × G RSA × ⎛⎜ 1 − ρ RSA ⎟,
⎝ ⎠

where ρRSA denotes the reflection coefficient at the connector of the RSA.

8) Replace RSA by the OBU receiver.

9) Measure BER of the OBU receiver according to clause B.4. If the BER is greater than 10-6 the test failed.

10) Repeat step 6 to step 9 for the carrier frequency fTx defined for channel 4 according to table 3 and clause 4.2.3.

11) If the manufacturer declared a worst case direction, the test is finished. Otherwise repeat step 4 to step 10 for
the four remaining orientations M1, M2, M3 and M4 of the OBU according to figure 1.

[Link].3 Conducted measurements

The following procedural step shall apply:

1) Prepare the test site according to clause B.[Link].

2) If the manufacturer declared a worst case direction, set a correction gain Gcorr equal to the gain of the OBU
receive antenna in the worst case direction as declared by the manufacturer. Otherwise set Gcorr equal to the
maximum gain of the OBU receive antenna as declared by the manufacturer.

3) Set the SMS1 such that it continuously transmits test signal TS1.

4) Set the carrier frequency fTx of SMS1 defined for channel 1 according to table 3 and clause 4.2.3.

5) Set the modulation index of the signal transmitted by the SMS1 to 0,5 or to the smallest possible value within
the allowed range of 0,5 to 0,9 supported by the SMS1.

6) Replace the OBU receiver by a power meter PM1.

7) Adjust the output signal power of the SMS1 such that the signal power indicated by the power meter PM1
equals the Pref in dBm plus the gain Gcorr in dB.

8) Replace PM1 by the OBU receiver.

9) Measure BER of the OBU receiver according to clause B.4. If the BER is greater than 10-6 the test failed.

10) Repeat step 6 to step 9 for the carrier frequency fTx defined for channel 4 according to table 3 and clause 4.2.3.

11) If the manufacturer declared a worst case direction, the test is finished. Otherwise repeat step 4 to step 10 for
the four remaining orientations M1, M2, M3 and M4 of the OBU according to figure 1, where for each
orientation Gcorr takes on the corresponding value as declared by the manufacturer.

ETSI
 30 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

[Link] Receiver selectivity

[Link].1 General
This test shall be performed with radiated measurements.

Basic requirements and guidelines for measurements are provided in annex B.

Parameter descriptions and limits are provided in clause [Link].

The description in clause [Link].3 assumes that an OBU under test is used to receive downlink signals and to generate
uplink signals, both of type TM1. The test can be performed accordingly based on laboratory instruments, i.e. an RSU
simulator, to generate downlink signals of type TS1 and messages of type TM1 and to receive and evaluate uplink
signals of type TM1.

[Link].2 Unwanted signal characteristics

The receiver selectivity measurement shall be performed at least with an unmodulated single carrier unwanted signal
with frequencies fu differing by ± 20 MHz, ± 50 MHz, ± 100 MHz , and ± 200 MHz from the selected DSRC channel,
and a power level as specified in clause [Link].

The representative frequencies fu of the unwanted signal and the DSRC channel as selected by the manufacturer for
testing shall be stated in the test report.

NOTE: The manufacturer may extend the test in order to determine the actual value of the immunity against other
services.

[Link].3 Measurement of receiver selectivity in OBU boresight

1) Depending on the antenna connector of the RSU, set up the measurement arrangement as detailed in
clause B.[Link].

2) Replace the OBU under test by a LHCP RTA, orientated with its boresight towards Mcentre and connect a
power meter PM1 to it.

3) Mute the RSU signal.

4) Configure the ASG to transmit the unwanted signal waveform specified in clause [Link].2.

5) Determine the offset between the power setting at the ASG and the power level measured at the LHCP RTA,
including 3 dB for the LP to LHCP transformation, for the frequencies fu used for the measurement. This offset
should equal the offset between the ASG power setting and the incident power level received by a hypothetic
LP loss-less isotropic antenna at the location of the OBU antenna.

6) Mute the ASG signal.

7) Set the RSU to the mode that it transmits an unmodulated carrier.

8) Set the RSU output power to its maximum allowed value.

9) Adjust AT1 so that the incident power level received by a hypothetic LHCP loss-less isotropic antenna at the
location of the OBU antenna equals -37 dBm.

10) Put the OBU under test back in place.

11) Set the modulation index of the RSU to any convenient value, if it is adjustable.

12) Set RSU and OBU under test to a mode that they are able to process test messages TM1.

13) Set the RSU to a mode such that the OBU under test shall use the lower sub-carrier frequency fs.

14) Set the RSU carrier frequency fTx to a value in accordance with table 3, the unwanted signal frequency to a
value that differs +20 MHz from fTx, and the unwanted signal power to the level specified in table 8 for the
selected OBU receiver selectivity class.

ETSI
 31 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

15) Configure the ASG to transmit an unmodulated carrier, taking the offset determined in step 5 into account.

16) Measure the BER of the OBU under test according to clause B.4. If the BER is greater than the value specified
in clause [Link].2 the test failed.

17) Repeat step 16 with an unwanted signal frequency fu with -20 MHz difference to fTx.

18) Set the RSU carrier frequency fTx to a value in accordance with table 3, the unwanted signal frequency to a
value that differs + 50 MHz from fTx, and the unwanted signal power to the level specified in table 9 for the
selected OBU receiver selectivity class.

19) Configure the ASG to transmit an unmodulated carrier, taking the offset determined in step 5 into account.

20) Measure the BER of the OBU under test according to clause B.4. If the BER is greater than the value specified
in clause [Link].3 the test failed.

21) Repeat step 20 with the unwanted signal frequencies fu with - 50 MHz, ± 100 MHz , and ± 200 MHz
difference to fTx.

22) Repeat step 14 to step 21 with the other RSU carrier frequencies fTx in accordance with table 3.

23) Set the RSU to a mode such that the OBU under test shall use the upper sub-carrier frequency fs.

24) Repeat step 14 to step 22.

ETSI
 32 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

Annex A (normative):
Relationship between the present document and the
essential requirements of Directive 2014/53/EU
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.6] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.5].

Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.

Table A.1: Relationship between the present document and

the essential requirements of Directive 2014/53/EU

Harmonised Standard ETSI EN 300 674-2-2

The following requirements are relevant to the presumption of conformity
under the article 3.2 of Directive 2014/53/EU [i.5]
Requirement Requirement Conditionality
Reference:
No Description U/C Condition
Clause No
1 Maximum equivalent isotropically [Link] U
radiated power
2 Frequency error [Link] U
3 Transmitter spectrum mask [Link] U
4 Unwanted emissions [Link] U
5 Receiver spurious emissions [Link] U
6 Sensitivity [Link] U
7 Receiver selectivity [Link] U

Key to columns:

Requirement:

No A unique identifier for one row of the table which may be used to identify a requirement.

Description A textual reference to the requirement.

Clause Number Identification of clause(s) defining the requirement in the present document unless another
document is referenced explicitly.

Requirement Conditionality:

U/C Indicates whether the requirement shall be unconditionally applicable (U) or is conditional upon
the manufacturers claimed functionality of the equipment (C).

Condition Explains the conditions when the requirement shall or shall not be applicable for a requirement
which is classified "conditional".

Presumption of conformity stays valid only as long as a reference to the present document is maintained in the list
published in the Official Journal of the European Union. Users of the present document should consult frequently the
latest list published in the Official Journal of the European Union.

Other Union legislation may be applicable to the product(s) falling within the scope of the present document.

ETSI
 33 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

Annex B (normative):
Basics on testing
B.1 General conditions
B.1.1 Power source
For testing the equipment shall be powered by a test power source, capable of producing test voltages as declared by the
manufacturer.

For battery operated equipment the battery shall be removed and an external test power source shall be suitably
decoupled. For radiated measurements any external power leads shall be arranged so as not to affect the measurements.
If necessary, the external test power source may be replaced with the supplied or recommended internal batteries at the
required voltage, or a battery simulator. This shall be stated on the test report. For radiated measurements on portable
equipment, fully charged internal batteries shall be used. The batteries used shall be as supplied or recommended by the
applicant.

During tests the external test power source voltages shall be within a tolerance of ±1 % relative to the voltage at the
beginning of each test. The value of this tolerance can be critical for certain measurements. Using a smaller tolerance
provides a better uncertainty value for these measurements. If internal batteries are used, at the end of each test the
voltage shall be within a tolerance of ±5 % relative to the voltage at the beginning of each test.

The internal impedance of the external test power source shall be low enough for its effect on the test results to be
negligible. For the purpose of the tests, the voltage of the external test power source shall be measured at the input
terminals of the equipment.

B.1.2 Thermal balance

Before measurements are made the equipment shall have reached thermal balance in the test chamber.

The equipment shall be switched off during the temperature stabilizing period.

In the case of equipment containing temperature stabilization circuits designed to operate continuously, the temperature
stabilization circuits shall be switched on for a time period as declared by the manufacturer such that thermal balance
has been obtained, and the equipment shall then meet the specified requirements.

If the thermal balance is not checked by measurements, a temperature stabilizing period of at least one hour, or such
period as may be decided by the test laboratory, shall be allowed. The sequence of measurements shall be chosen and
the relative humidity content in the test chamber shall be controlled so that condensation does not occur.

B.1.3 Test signals

The following test signals and test messages are defined:

Table B.1: Test signals and messages

Test signal/message Description

Test Messages (TM1) Set of DSRC messages supporting initialization and ECHO command compliant to CEN
EN 12795 [7], CEN EN 12834 [8], and ISO 14906 [9].
Test Signal (TS1) Properly modulated and coded DSRC signal where the data is a continuously repeated
maximum length pseudo-random sequence generated by a linear feedback shift register.
The period of the pseudo-random sequence shall be 511 bits.
Test Signal (TS2) Continuous DSRC uplink signal with unmodulated sub-carrier. The sub-carrier frequency
shall be settable to fs = 1,5 MHz and fs = 2,0 MHz, respectively.

Data coding and bit rates in downlink and uplink shall be according to parameters D7, U7 and D8, D8a, U8, U8a of
CEN EN 12253 [3], respectively.

ETSI
 34 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

B.1.4 Test sites

B.1.4.1 Shielded anechoic chamber
A typical anechoic chamber is shown in figure B.1. This type of test chamber attempts to simulate free space
conditions.

Absorber

Shielding

Reference points
Absorber

Absorber
EUT
Test antenna

Non-conductive supports

Absorber

Figure B.1: Typical anechoic chamber

The chamber contains suitable antenna supports on both ends.

The supports carrying the test antenna and EUT shall be made of a non-permeable material featuring a low value of its
relative permittivity.

The anechoic chamber shall be shielded. Internal walls, floor and ceiling shall be covered with radio absorbing material.
The shielding and return loss for perpendicular wave incidence versus frequency as detailed in figure B.2 shall be met
by anechoic chambers used to perform tests.

ETSI
 35 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

Loss / dB
110
105
100

90

80

70 Minimum shielding loss

60

50

40

30

20 Minimum return loss

10

0
10k 100k 1M 10M 30M 100M 300M 1G 10G 26G 100G

Frequency f / Hz

Figure B.2: Minimal shielding and return loss for shielded anechoic chambers

Both absolute and relative measurements can be performed in an anechoic chamber. Where absolute measurements are
to be carried out the chamber shall be verified.

The shielded anechoic chamber test site shall be calibrated and validated for the frequency range being applicable.

NOTE: Information on uncertainty contributions, and verification procedures are detailed in clause 5 and
clause 6, respectively, of ETSI TR 102 273-2 [11].

B.1.4.2 Open area test site

A typical open area test site is shown in figure B.3.

Dipole antennas

Antenna mast

Turntable

0m
m or 1
h 3
ngt
nge le
Ra

Ground plane

Figure B.3: Typical open area test site

ETSI
 36 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

The ground plane shall provide adequate size, such as to approximate infinite size. Relevant parts of the ground plane
shall be covered by absorbing material.

Test shall be limited to the frequency range between 30 MHz and 1 000 MHz.

Measurements performed in open area test sites follow the same procedures as detailed for radiated measurements
performed in shielded anechoic chambers.

The open area test site shall be calibrated and validated for the frequency range being applicable.

NOTE: Information on uncertainty contributions, and verification procedures are detailed in clause 5 and
clause 6, respectively, of ETSI TR 102 273-4 [i.3].

B.1.4.3 Test fixture

A test fixture is a device that allows for conducted measurements of an EUT that does not provide antenna connectors
itself. The EUT can be either an OBU or a RSU. A test fixture consists of at least one RF connector featuring a
characteristic impedance of 50 Ω, subsequently called 50 Ω RF connector, and a device for electromagnetic coupling to
the EUT. It incorporates a means for repeatable positioning of the EUT. Figure B.4 illustrates a typical test fixture.

Figure B.4: Typical test fixture

The coupling device usually comprises a small antenna that is placed, physically and electrically, close to the EUT. This
coupling device is used for sampling or generating the test fields when the EUT is undergoing testing. Figure B.5
illustrates an EUT mounted on a test fixture.

Figure B.5: EUT mounted in a typical test fixture

The entire assembly of test fixture plus EUT is generally compact and it can be regarded as a EUT with antenna
connector. Its compactness enables the whole assembly to be accommodated within a test chamber, usually a climatic
facility. The circuitry associated with the RF coupling device should contain no active or non-linear components and
should present a VSWR of better than 1,5 to a 50 Ω line.

Absolute measurements shall not be made in a test fixture as the antenna of the EUT and the one of the test fixture
might be mutually in the near-field range of each other. Hence, only relative measurements shall be performed that shall
be related to results taken on a verified free field test site.

ETSI
 37 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

The way to relate the results is by a process, referred to as field equalization, in which the relevant parameter,
e.g. effective radiated power, receiver sensitivity, etc. is initially measured on a free field test site under normal
environmental conditions and then subsequently re-measured using the test fixture under the very same environmental
conditions. The difference, e.g. in dB, of the two results is termed the coupling factor of the test fixture and provides the
link between all the results of EUT tests carried out in the test fixture and its performance on a verified free field test
site. As a general rule, the coupling factor should not be greater than 20 dB.

Emission tests are generally limited to the nominal frequencies, for which the performance of the test fixture has been
verified.

Only after it has been verified that the test fixture does not affect performance of the EUT, the EUT can be confidently
tested.

The test fixtures shall be calibrated and validated for the frequency range they are used for.

NOTE: Information on uncertainty contributions, and verification procedures are detailed in clause 5 and
clause 6, respectively, of ETSI TR 102 273-6 [12].

B.1.5 General requirements for RF cables

All RF cables including their connectors at both ends used within the measurement arrangements and set ups shall be of
coaxial type featuring within the frequency range they are used:

• a nominal characteristic impedance of 50 Ω;

• a VSWR of less than 1,2 at either of their ends, preferably better;

• a shielding loss in excess of 60 dB, preferably better.

All RF cables exposed to radiation shall be loaded with ferrite beads spaced with a gap of Dfb between each other along
the entire length of the cable. Such cables are referred to as FCCA. The gap Dfb shall be less than half of the signal's
wavelength under test.

All RF cables shall be routed suitably in order to reduce impacts on antenna radiation pattern, antenna gain, antenna
impedance.

NOTE: Further details are provided in ETSI TR 102 273-2 [11].

B.1.6 Conducted measurements

B.1.6.1 One antenna connector arrangement
Figure B.6 shows the measurement arrangements that shall be used in case of a single antenna connector at the EUT.

ETSI
 38 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

MSS1
or FCCA
SMS1

CC FCCA EUT

RD FCCA a)

MSS MSS
FCCA 1 FCCA
1
off

CC FCCA PM MSS
CC FCCA
2

RD
off
FCCA b) RD FCCA c)

Figure B.6: Measurement arrangement with one antenna connector:

a) for measurement of EUT parameters
b) for adjusting input power to EUT
c) for substitution measurements

B.1.6.2 Two antenna connectors arrangement

Figure B.7 shows the measurement arrangements that shall be used in case of a two antenna connectors at the EUT.

MSS1
or FCCA
SMS 1

a) EUT

RD FCCA

MSS
MSS
FCCA 1 FCCA
1
off

b) PM MSS
c) 2

RD FCCA
off RD FCCA

Figure B.7: Measurement arrangement with two antenna connectors:

a) for measurement of EUT parameters
b) for adjusting input power to EUT
c) for substitution measurements

ETSI
 39 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

B.1.6.3 Test site requirements

Conducted measurements shall be performed at the antenna connector(s) of the EUT.

B.1.6.4 Site preparation for conducted measurements

B.[Link] Monochromatic signals
If the measurement arrangement with one antenna connector is used, the measurement set up depicted in figure B.6
applies and the site preparation is as follows:

1) The calibrated MSS1 shall be connected to the antenna connector of the EUT via the calibrated CC providing
three terminals.

2) The RD shall be connected to the antenna connector of the EUT via the remaining third terminal of the
calibrated CC.

If the measurement arrangement with two antenna connectors is used, the measurement set up depicted in figure B.7
applies and the site preparation is as follows:

1) The calibrated MSS1 shall be connected to the receive antenna connector of the EUT.

2) The RD shall be connected to the transmit antenna connector of the EUT.

B.[Link] Modulated signals

If the measurement arrangement with one antenna connector is used, the measurement set up depicted in figure B.6
applies and the site preparation is as follows:

1) The calibrated SMS1 shall be connected to the antenna connector of the EUT via the calibrated CC providing
three terminals.

2) The RD, i.e. either an RSU receiver or a measurement receiver, shall be connected to the antenna connector of
the EUT via the remaining third terminal of the calibrated CC.

If the measurement arrangement with two antenna connectors is used, the measurement set up depicted in figure B.7
applies and the site preparation is as follows:

1) The calibrated SMS1 shall be connected to the receive antenna connector of the EUT.

2) The RD, i.e. either an RSU receiver or a measurement receiver, shall be connected to the transmit antenna
connector of the EUT.

B.1.7 Radiated measurements

B.1.7.1 One antenna arrangement
Figure B.8 shows the measurement arrangements that shall be used in case one test antenna TA for transmitting and
receiving signals are selected for testing the EUT.

ETSI
 40 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

Far-field region &

free-space condition
MSS
FCCA
1
Gain GTA

CC FCCA EUT
boresight
Test
antenna (TA)
RD FCCA a)
d

Far-field region &

MSS1 free-space condition
or FCCA
SMS1 Gain GTA RSA

CC FCCA PM 1
boresight
Test
antenna (TA) Gain GRSA
RD
off
FCCA b)
d

Far-field region &

MSS free-space condition
1 FCCA
off Gain GTA TSA

MSS
CC FCCA FCCA
boresight 2
Test
antenna (TA) Gain GTSA
RD FCCA c)
d

Figure B.8: Measurement arrangement with one test antennas:

a) for measurements of EUT parameters
b) for adjustment of the incident power to the EUT
c) for measurement steps using the substitution antenna

ETSI
 41 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

B.1.7.2 Two antennas arrangement

Figure B.9 shows the measurement arrangements that shall be used in case two test antennas, i.e. TTA and RTA, are
selected for testing the EUT.

Far-field region &

MSS1 free-space condition
or FCCA
SMS1
bore
sight α
TTA
MCentre
boresight
a) EUT ddisplace

bore
sight α

RD FCCA
RTA d

Far-field region &

free-space condition
MSS
FCCA
1
bore
sight α
TTA
RSA
MCentre
boresight
b) PM 1 ddisplace

Gain GRSA
bore
sight α
RD
FCCA
off
RTA d

Far-field region &

MSS free-space condition
1 FCCA
off
bore
sight α
TTA
TSA
MCentre
ddisplace

boresight MSS
c) FCCA
2

Gain GTSA
bore
sight α

RD FCCA
RTA d

Figure B.9: Measurement arrangement with two test antennas:

a) for measurements of EUT parameters
b) for adjustment of the incident power to the EUT
c) for measurement steps using the substitution antenna

ETSI
 42 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

B.1.7.3 Test site requirements

B.[Link] Measurement distances
Within an open area test site or a shielded anechoic chamber the measurement distance or range length d depicted in
figure B.8 and figure B.9 shall be such, that the antennas on both sides of the radio link are mutually in the far field of
each other, i.e. d shall be according to the most stringent of the following three equations:

d>
(
2 × D0,TA + D0,EUT 2 ) , d > 5 × (D0,TA + D0,EUT ) and d > 2 × λ,
λ

where D0,TA, D0,EUT and λ denote the largest dimension of the test antenna, the EUT antenna, and the
wavelength, respectively.

This distance d shall be measured between:

• the centre of aperture of the test antenna TA, in case of a horn antenna, or the feeding point in case the TA is
of another type; and

• the feeding point of the EUT antenna if the location of the EUT antenna is known, or the volume centre of the
EUT if the location of its antennas is unknown.

B.[Link] Free-space wave propagation

Within an open area test site or a shielded anechoic chamber a radio path between a transmitting and receiving antenna
requires a certain amount of clearance around the central or direct ray if the signal expected from free-space
propagation is to be received.

The clearance is usually quoted in terms of Fresnel zones. As depicted in figure B.10 the first Fresnel zone encloses all
radio paths from the transmitting to the receiving antenna for which the detour path length dF1 + dF2 relative to the
length d of the direct radio path does not exceed half of the wavelength λ, i.e. a phase change of 180°, of the radiated
signal in air.

dF1 + dF2 - d ≤ λ / 2.

Disregarding the non-conductive, dielectric supports of the EUT and the test antenna(s) the clearance around the LOS
path between the transmitting and receiving antenna shall be such that at least the first Fresnel zone is free of any
obstacles.

1st Fresnel Zone

dF1 dF2
Detour path

EUT d
Central or direct path
Test antenna
Reference
or focal points

Non-conductive supports

Figure B.10: First Fresnel zone with direct and detour radio path

ETSI
 43 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

B.1.7.4 Test and substitution antennas

Test antennas are used to detect the radiation from the EUT or to transmit a signal towards the EUT while substitution
antennas together with signal generators are used to replace the EUT and its antenna in substitution measurements.

The test or substitution antenna shall be either LHCP, LP, or XP, whichever is required in the test procedure of the
respective EUT parameter. Cross-polarized test or substitution antennas require a XPD > 25 dB within their specified
frequency range.

Preferably test or substitution antennas with pronounced directivities shall be used. However, their directivities Di
relative to an isotropic radiator shall be such that the antennas on both sides of the radio link are mutually in the far field
region of each other.

If the symmetry of the test or substitution antenna does not match the one of its feeding cable, a symmetry matching
circuit (balun) shall be inserted between the antenna output and the input of its feeding RF cable.

The return loss at the terminal of the test or substitution antenna shall exceed 15 dB within its specified frequency
range.

When measuring signals in the frequency range up to 1 GHz the test or substitution antenna shall be either:

• a half wavelength dipole, resonant at the operating frequency; or

• a shortened dipole, calibrated to the half wavelength dipole; or

• a biconical antenna.

For measurements between 1 GHz and 4 GHz either:

• a half wavelength dipole; or

• a biconical antenna; or

• a horn radiator may be used.

When measuring signals in the frequency range above 4 GHz a horn antenna shall be used.

The type of test or substitution antenna actually used in the tests shall be stated in the test report.

B.1.7.5 Site preparation for radiated OBU measurements

B.[Link] Monochromatic signals
If the measurement arrangement with one test antenna is used, the measurement set up depicted in figure B.8 applies
and the site preparation is as follows:

1) The LHCP calibrated Test Antenna (TA, TTA: transmit path, RTA: receive path) shall be suited for the range
of carrier frequencies fTx in accordance with clause 4.2.3. It shall be mounted in a shielded anechoic chamber
on a vertical pole. The distance between any part of this TA and the ceiling, floor or walls shall be at least
0,5 m. The height of the phase centres above floor of the TA and the CA shall be equal. The CA is either the
OBU antenna (EUT) or the RSA. The boresight of the TTA shall point towards the phase centre of the CA.

2) The TA shall be connected via a CC featuring three terminals to a calibrated MSS1 using calibrated FCCAs.
The remaining third terminal of the circulator shall be connected via a calibrated FCCA to the input of a
calibrated RD, i.e. spectrum analyser or measuring receiver, calibrated at the frequencies of the
monochromatic signals under consideration. Appropriate precautions shall be taken to prevent overloading the
input of the RD.

ETSI
 44 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

3) The LHCP calibrated RSA of gain GRSA shall be suited for the range of carrier frequencies fTx in accordance
with clause 4.2.3. It shall be mounted on a vertical pole within the "quiet zone" at the other end of the shielded
anechoic chamber. This pole shall be mounted on a turntable allowing rotating the RSA's phase centre around
a vertical axis. The distance between any part of the RSA and the ceiling, floor or walls shall be at least 0,5 m.
Further, the distance d between the TTA and the RSA shall be such that the two antennas are mutually in the
far field of each other, see clause B.[Link]. The boresight of the RSA shall point towards the phase centre of
the TA. The output of the RSA shall be connected directly to the power sensor of power meter PM1 that shall
be calibrated to the frequency of the monochromatic signal under consideration.

If the measurement arrangement with two test antennas is used, the measurement set up depicted in figure B.9 applies
and the site preparation is as follows:

1) The LHCP calibrated TTA and the LHCP calibrated RTA shall each be suited for the range of carrier
frequencies fTx in accordance with clause 4.2.3. They shall be mounted in a shielded anechoic chamber on a
vertical pole. These two antennas shall be displaced either horizontally or vertically such as to minimize the
coupling between them. Vertically polarized TTA and RTA shall be displaced vertically whilst horizontally
polarized TTA and RTA shall be displaced horizontally. Additionally, the phase centre of the TTA shall be
displaced from the phase centre of the RTA by a distance ddisplace such that the coupling loss between the two
antennas becomes greater than 30 dB and the overall uncertainty of the measurement set-up shall comply with
the requirements stated in table 10. The actual coupling loss and the distance ddisplace between the TTA and
RTA shall be stated in the test report together with a unique identification of the TTA and RTA used. The
position between both phase centres is denoted Mcentre. The distance between any part of the TTA and RTA
with respect to the ceiling, floor or walls shall be at least 0,5 m. The height of Mcentre and the phase centre of
the CA above floor shall be equal. The CA is either the OBU antenna or the RSA. The boresight of the TTA
and RTA shall point towards the phase centre of the CA.

2) The TTA shall be connected to a calibrated MSS1 using calibrated FCCAs.

3) The RTA shall be connected to the input of a calibrated RD, i.e. spectrum analyser or measuring receiver,
using calibrated FCCA. The RD shall be calibrated at the frequencies of the monochromatic signals under
consideration. Appropriate precautions shall be taken to prevent overloading the input of the RD.

4) The LHCP RSA of gain GRSA shall be suited for the range of carrier frequencies fTx in accordance with
clause 4.2.3. It shall be mounted on a vertical pole within the "quiet zone" at the other end of the shielded
anechoic chamber. This pole shall be mounted on a turntable allowing to rotate the RSA's phase centre around
a vertical axis. The RSA shall be positioned close to the middle between the ceiling and the floor. Its boresight
shall point to the centre between the phase centres of the TTA and RTA. The distance between any part of the
RSA and the ceiling, floor or walls shall be at least 0,5 m. Further, the distance d between the TTA and the
RSA as well as between the RTA and the RSA shall be such that the two antennas on both sides of the radio
link are mutually in the far field region of each other, see clause B.[Link]. Additionally, the distance d
between CA and the position Mcentre shall be such that the displacement angle αdisplace between TTA and RTA
as observed from the CA complies with:

⎛ d displace ⎞
α displace = 2 × arctan⎜⎜ ⎟⎟,
⎝ 2×d ⎠
α displace ≤ 2o for horizontally displaced antennas,
α displace ≤ 6o for vertically displaced antennas.
The output of the RSA shall be connected directly to the power sensor of power meter PM1 that shall be
calibrated at the frequencies of the monochromatic signals under consideration.

ETSI
 45 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

B.[Link] Modulated signals

If the measurement arrangement with one test antenna is used, the measurement set up depicted in figure B.8 applies
and the site preparation is as follows:

1) The LHCP calibrated test antenna (TA, TTA: transmit path, RTA: receive path) shall be suited for the range of
carrier frequencies fTx in accordance with clause 4.2.3. It shall be mounted in a shielded anechoic chamber on
a vertical pole. The distance between any part of this TA and the ceiling, floor or walls shall be at least 0,5 m.
The height of the phase centres above floor of the TA and the CA shall be equal. The CA is either the OBU
antenna (EUT) or the RSA. The boresight of the TTA shall point towards the phase centre of the CA.

2) The TA shall be connected via a CC featuring three terminals to a calibrated SMS1 using calibrated FCCAs.
The remaining third terminal of the circulator shall be connected via a calibrated FCCA to the input of a
calibrated RD, i.e. RSU receiver or measuring receiver, calibrated at the frequencies of the modulated signals
or messages under consideration. Appropriate precautions shall be taken to prevent overloading the input of
the RD.

3) The LHCP calibrated RSA of gain GRSA shall be suited for the range of carrier frequencies fTx in accordance
with clause 4.2.3. It shall be mounted on a vertical pole within the "quiet zone" at the other end of the shielded
anechoic chamber. This pole shall be mounted on a turntable allowing to rotate the RSA's phase centre around
a vertical axis. The distance between any part of the RSA and the ceiling, floor or walls shall be at least 0,5 m.
Further, the distance d between the TTA and the RSA shall be such that the two antennas are mutually in the
far field of each other, see clause B.[Link]. The boresight of the RSA shall point towards the phase centre of
the TA. The output of the RSA shall be connected directly to the power sensor of power meter PM1 that shall
be calibrated at the frequencies of the monochromatic signals under consideration.

If the measurement arrangement with two test antennas is used, the measurement set up depicted in figure B.9 applies
and the site preparation is as follows:

1) The LHCP calibrated TTA and the LHCP calibrated RTA shall each be suited for the range of carrier
frequencies fTx in accordance with clause 4.2.3. They shall be mounted in a shielded anechoic chamber on a
vertical pole. These two antennas shall be displaced either horizontally or vertically such as to minimize the
coupling between them. Vertically polarized TTA and RTA shall be displaced vertically whilst horizontally
polarized TTA and RTA shall be displaced horizontally. Additionally, the phase centre of the TTA shall be
displaced from the phase centre of the RTA by a distance ddisplace such that the coupling loss between the two
antennas becomes greater than 30 dB and the overall uncertainty of the measurement set-up shall comply with
the requirements stated in table 10. The actual coupling loss and the distance ddisplace between the TTA and
RTA shall be stated in the test report together with a unique identification of the TTA and RTA used. The
position between both phase centres is denoted Mcentre. The distance between any part of the TTA and RTA
with respect to the ceiling, floor or walls shall be at least 0,5 m. The height of Mcentre and the phase centre of
the CA above floor shall be equal. The CA is either the OBU antenna or the RSA. The boresight of the TTA
and RTA shall point towards the phase centre of the CA.

2) The TTA shall be connected to a calibrated SMS1 using calibrated FCCAs.

3) The RTA shall be connected to the input of a calibrated RD, i.e. RSU receiver or measuring receiver, using
calibrated FCCA. The RD shall be calibrated to the frequency of the modulated signal or message under
consideration. Appropriate precautions shall be taken to prevent overloading the input of the RD.

ETSI
 46 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

4) The LHCP RSA of gain GRSA shall be suited for the range of carrier frequencies fTx in accordance with
clause 4.2.3. It shall be mounted on a vertical pole within the "quiet zone" at the other end of the shielded
anechoic chamber. This pole shall be mounted on a turntable allowing to rotate the RSA's phase centre around
a vertical axis. The RSA shall be positioned close to the middle between the ceiling and the floor. Its boresight
shall point to the centre between the phase centres of the TTA and RTA. The distance between any part of the
RSA and the ceiling, floor or walls shall be at least 0,5 m. Further, the distance d between the TTA and the
RSA as well as between the RTA and the RSA shall be such that the two antennas on both sides of the radio
link are mutually in the far field region of each other, see clause B.[Link]. Additionally, the distance d
between CA and the position Mcentre shall be such that the displacement angle αdisplace between TTA and RTA
as observed from the CA complies with:

⎛ d displace ⎞
α displace = 2 × arctan⎜⎜ ⎟⎟,
⎝ 2×d ⎠
α displace ≤ 2o for horizontally displaced antennas,
α displace ≤ 6o for vertically displaced antennas.
The output of the RSA shall be connected directly to the power sensor of power meter PM1 that shall be
calibrated at the frequencies of the monochromatic signals under consideration.

B.[Link] Arrangement for OBU transmitter unwanted emissions measurement

Figure B.11 and figure B.12 detail the arrangements used for measurement of the OBU transmitter unwanted emissions.

Absorber

Shielding

OBU
Absorber

TTA Absorber

RTA

Non-conductive supports

Absorber

Figure B.11: Test set up for OBU unwanted emission measurements (side view)

Figure B.12 shows the turntable in its initial position MT0. MT1, MT2 and MT3 indicate the other angular positions
used.

ETSI
 47 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

y
MT1

Turntable
Far field &
free-space condition

RTA
MT2 boresight of OBU MT0
OBU
bo x
re

FCCA
sig 1, θ
h 0
to m
fT
TA

TTA
RD
FCCA MSS1

MT3

Figure B.12: Test set up for OBU unwanted emission measurements (top view)

For the OBU transmitter unwanted emissions arrangement shown in figure B.11 and figure B.12:

1) The LHCP calibrated TTA and the OBU antenna shall be installed at fixed distance of 1,0 m with fixed
orientation relative to each other on a support, which itself is mounted on a turntable.

2) The boresight of the TTA shall point towards the phase centre of the OBU antenna.

3) The phase centre Mc of the OBU antenna shall be in the axis of the turntable. If the phase centre Mc of the
OBU under test is unknown and no antenna is visible, the volume centre of the OBU under test shall be used
instead.

4) The boresight of the OBU antenna shall point to the phase centre of the RTA in case the turntable is in its
initial angular position MT0 as shown in figure B.12.

5) The TTA shall be suited for the range of carrier frequencies fTx listed in table 3.

6) The vertical polarized calibrated RTA shall be dedicated to the frequency band actually under test. Different
frequency bands shall be tested according to table 6.

7) The RTA shall be mounted on a vertical pole. The distance from the RTA to the axis of the turntable shall be
such as to allow for full 360o rotation of the turntable. The height of the phase centres above ground of the
RTA and the OBU antenna shall be equal.

8) The distance between any part of the TTA, and OBU antenna, respectively, and the ceiling, floor or walls shall
be at least 0,5 m.

9) Every antenna of this set up shall always be mutually in the far field of any other antenna of this set up.

10) The distance between any part of the RTA and the ceiling, floor or walls shall be at least half of the
wavelength actually under test.

11) The RTA shall be connected to the input of a calibrated RD, i.e. spectrum analyser or measuring receiver,
using a calibrated, ferrited coaxial cable. The RD shall be calibrated to the frequency to the actual frequency
under test.

ETSI
 48 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

B.[Link] Arrangement for OBU receiver selectivity measurement

Figure B.13 and figure B.14 detail the arrangements used for measurement of the receiver selectivity in OBU antenna
boresight.

Figure B.13 applies for an RSU with separate antenna connectors for receive and transmit path.

Far-field region &

ASG FCCA

Combiner
free-space condition

RSU
b o re
Tx AT1 FCCA sight α
RTxA
Mcentre

ddisplace
boresight
OBU
RSU

b o re
sight α
RSU
Rx AT2 FCCA
RRxA d

Figure B.13: OBU receive parameter measurement arrangement for horizontally separated RSU
antennas and unwanted signal injection in direction of OBU antenna boresight

In case the RSU provides only a single antenna connector for both, the transmit and receive path, a CC shall be used in
order to split up the single antenna connector into two antenna connectors, one for the receive path and one for the
transmit path; see figure B.14.

Far-field region &

ASG FCCA
Combiner

free-space condition

bore
AT1 FCCA sig ht α
RTxA
CC Mcentre
RSU
ddisplace
boresight
Tx & OBU
Rx

bore
s ight α
AT2 FCCA
RRxA d

Figure B.14: OBU receive parameter measurement arrangement with CC for horizontally separated
RSU antennas and unwanted signal injection in direction of OBU antenna boresight

For all OBU receiver selectivity measurement arrangements:

1) The RTxA shall be mounted on a vertical pole within the "quiet zone" of the shielded anechoic chamber. The
distance between any part of the RTxA and the ceiling, floor or walls shall be at least 0,5 m.

2) The RRxA shall be mounted on a vertical pole within the "quiet zone" of the shielded anechoic chamber. The
distance between any part of the RRxA and the ceiling, floor or walls shall be at least 0,5 m.

3) The phase centre of the RTxA shall be displaced from the phase centre of the RRxA by ddisplace. The position
between both phase centres is denoted Mcentre.

4) The displacement shall either be horizontally or vertically such as to minimize the coupling between these
antennas. The distance ddisplace shall be such that the coupling loss between the two antennas exceeds 30 dB.

ETSI
 49 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

The actual coupling loss and the distance ddisplace shall be stated in the test report together with the unique
identification of the RTxA and RRxA used.

5) The OBU under test shall be fixed on a vertical pole at the other end of the shielded anechoic chamber, such
that its antenna boresight direction points towards Mcentre.

6) The height of the phase centres above floor of the RTxA, RRxA, TTA and the OBU antenna shall be equal.

7) The boresight of the RTxA shall point towards the phase centre of the OBU antenna.

8) The boresight of the RRxA shall point towards the phase centre of the OBU antenna.

9) The distance d shall be chosen so that the OBU antenna(s) are mutually in the far field of RTxA and RRxA,
see clause B.[Link].

10) The displacement angle αdisplace = 2 × α between RTxA and RRxA as observed from the OBU under test shall
comply with:

⎛ d displace ⎞
α displace = 2 × arctan⎜⎜ ⎟⎟,
⎝ 2×d ⎠
α displace ≤ 2o for horizontally displaced antennas,
α displace ≤ 6o for vertically displaced antennas.
11) Ensure by proper decoupling that the signal from the ASG is not disturbing the RSU receiver (this can be
validated by a CRC check of the received frames, or a noise level monitoring).

For the arrangement with an RSU with separate antenna connectors for receive and transmit path (figure B.13):

1) Connect the RRxA to the RSU receiver via an isolator, an adjustable attenuator AT2 with attenuation ATNAT2,
and an FCCA.

2) Connect the RSU transmitter to the RTxA via an isolator, an adjustable attenuator AT1, an FCCA, and a
combiner with three terminals.

3) Connect an ASG via an FCCA to the remaining terminal of the combiner.

For the arrangement with an RSU with single antenna connector for receive and transmit path (figure B.14):

1) Connect the RSU transceiver via an isolator to a CC.

2) Connect the CC to the RTxA via an adjustable attenuator AT1, an FCCA, and a combiner with three terminals.

3) Connect an ASG via an FCCA to the remaining terminal of the combiner.

4) Connect the RRxA to the CC via an adjustable attenuator AT2 with attenuation ATNAT2 and an FCCA.

B.2 Instruments
B.2.1 Receiving device
The RD shall be either a spectrum analyser or a measurement receiver. The subsequent requirements shall apply for a
spectrum analyser:

1) The level of the superposition of all RF signals simultaneously fed to the input of the spectrum analyser shall
be within its range of specification applying for its calibrated operational mode of operation.

2) The RD shall be operated only within modes for which the instrument has been calibrated.

3) For any frequency to be measured, the noise floor of the RD shall be at least 10 dB below any power value
intended to be measured, e.g. limits for spurious emissions, referred to the location where the limit applies.

ETSI
 50 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

4) The DC voltage fed to the input of the spectrum analyser shall be within its range of specification applying for
its calibrated operational mode of operation.

5) The frequency error of the spectrum analyser shall be compliant with table 10.

6) The nominal characteristic impedance of the spectrum analyser's input connector shall match the nominal
characteristic impedance of the device connected to this input connector. The VSWR shall be less than 2,0. If
this cannot be met, an attenuator or an isolator featuring a VSWR less or equal to 2,0 within the frequency
range of the measurement shall be attached to the input of the spectrum analyser and the EUT shall be
connected to the input of this attenuator or isolator.

7) The Video Bandwidth (VBW) shall always be equal to or greater than the Resolution Bandwidth (RBW)
selected. The RBW will also be referred to as the reference or equivalent bandwidth. See as well clause 4.5 of
CISPR 16-1 [14].

8) For spurious and out-of-band emission measurements the RBW of the spectrum analyser shall be set to the
required RBW specified in the test procedure:

- The measurements may be performed using an RBW that is less than the required one and multiple
measurements shall be carried out across the required RBW within non-overlapping frequency bins
whose width equal to the selected RBW. The signal power measured within each of these frequency bins
shall be added up to obtain the wanted signal power within the required RBW.

- If the required RBW is less than the smallest one offered by the spectrum analyser and does not match
any of the available ones of the spectrum analyser, the measured signal powers shall be performed with a
RBW that is closest to the required RBW. The signal power measured shall be scaled according to the
ratio of the required RBW to the RBW used while performing the measurements.

9) Signal power measurements performed using the spectrum analyser's CW mode shall equal to the arithmetic
average of the largest and smallest signal level measured during the observation time.

10) The spectrum analyser shall be used only after the instrument has warmed up. The minimum warm up duration
is usually specified in the manual of the spectrum analyser. If this is not the case, a warm up time of at least
half an hour shall be considered.

11) The spectrum analyser shall be calibrated before usage.

12) If the dynamic range of the spectrum analyser in conjunction with the required setting of the RBW is not
sufficient to measure relevant weak signals in the presence of irrelevant strong signal components appropriate
measures to suppress the irrelevant strong signal components shall be applied in agreement between
manufacturer and test laboratory and shall be described in the test report.

13) The peak detector shall be used.

For the usage of a measurement receiver the above requirements shall apply as well with the exception, where
requirements are not applicable, e.g. VBW.

B.2.2 RF power sensor

The subsequent requirements shall apply for RF signal power measurements.

1) RF signal power measurements shall not be performed before warm-up of the RF power sensor and the RF
power meter. The warm-up duration is usually specified in the manual of the instrument. If this is not the case
the instrument shall be allowed for a warm-up time of at least half an hour.

2) The RF power sensor and RF power meter shall be calibrated and zeroed before usage according to the
requirements and the procedure specified in the manual of the instrument.

3) The RF power sensor shall be kept within a small enough temperature range such as to keep the measurement
uncertainty of the measurement set up within the range specified in clause 5.2.

4) The VSWR at the input of the RF power sensor shall be less than 1,5 within the frequency range of the
measurement under investigation.

ETSI
 51 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

5) The level of the superposition of all signals simultaneously fed to the input of the RF power sensor shall be
within the dynamic range of the RF power sensor as stated by its manufacturer for its operational mode.

6) The power sensor shall be dedicated for the signal waveform under consideration.

B.2.3 Combiner
All RF combiners used within the measurement arrangements and set ups shall provide coaxial connectors at all ports
and feature within the frequency range they are used:

• a nominal characteristic impedance of 50 Ω at each port;

• a VSWR of less than 1,5 at each port;

• an isolation between the input ports of at least 10 dB; and

• an amplitude balance between each of the input ports and the output port of less than 1 dB.

B.3 Power of modulated RSU carrier

Figure B.15 illustrates as an example the basic time-dependent sequence of unmodulated and modulated RSU transmit
signals for a case of a modulation index m = 0,5, where the transmit signal power Pmod, and PCW, respectively, of the
modulated, and unmodulated signal parts are equal. The condition of equal power Pmod = PCW is not required by the
present document.

NOTE: Figure B.15 does not allow extracting valid timing relations between carrier frequency and bit rate.

PCW = Pmod
RSU CW signal Modulated RSU signal
with power PCW with power Pmod
RSU signal Amod + m
ACW
Amod

Amod - m

time

Modulation index m = 0,5

Figure B.15: RSU transmit signal

An RSU normally allows for a transmit mode "send unmodulated carrier", i.e. continuous transmission of the
1 2
unmodulated carrier. Thus it is possible to measure the power of the unmodulated signal in figure B.15, PCW = ACW ,
2
by means of a thermal power sensor or a spectrum analyser.

An RSU does normally not allow for continuous transmission of the modulated carrier. In what follows a procedure is
1 2
described, that allows to estimate the power Pmod = Amod
2
( )
1 + m 2 of the modulated carrier:

1) Set the RSU in a mode that it transmits an unmodulated carrier. Measure PCW.

ETSI
 52 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

2) Set the RSU in a mode that it transmits BSTs of maximum possible duration Tmod with a repetition period as
close as possible to twice of the duration of a BST transmission. The gap between subsequent BST
transmissions has duration TCW. The duration Tmod and TCW shall be constant within the following test.

3) Measure the average signal power Pavg of the signal transmitted according to step 2 with measurement time of
at least ten times the repetition period TCW + Tmod.

4) Measure the duration Tmod and TCW.

5) Calculate Pmod = Pavg +

TCW
Tmod
(Pavg − PCW .)

B.4 Bit error ratio measurements

B.4.1 Basics
The required BER for communication is referred to as parameters D9 and U9 in CEN EN 12253 [3].

BER measurements shall be conducted either in a direct or indirect way.

The direct way requires the possibility to generate and receive a continuous bit stream of significant length. The fraction
of erroneous bits out of the total number of received bits is the BER. This approach uses standard laboratory equipment
for BER measurement and requires a modification of the EUT.

The indirect way is based on generating and receiving frames of limited length where any bit errors in the frame can be
detected by means of a CRC. The fraction of erroneous frames out of the total number of frames, which is called the
FER, allows to estimate the BER assuming that bit errors are equally distributed. Precautions shall be taken to prevent
drops of error-free received frames caused by specific implementation of upper layers.

B.4.2 BER measurement

BER may be measured indirectly, see clause B.4.3.

B.4.3 FER measurement

B.4.3.1 Mathematical expressions
Assuming equally distributed and statistically independent occurrence of erroneous bits the following relations between
FER, BER, and total number N of transmitted bit within a single frame apply:

FER = 1 - (1 - BER)N,
lg (1− FER)
BER = 1 − 10 N
= 1 − N 1 − FER .

The minimum number CF of frames together with the frame size shall be reported.

EXAMPLE 1: With BER = 10-6 and frame length N = 1 000 the equivalent FER amounts to approximately
1,0 × 10-3. A reasonable number CF of frames to be transmitted is 10 000, i.e. 10 frames may be
lost on average.

EXAMPLE 2: For a large value of FER, e.g. 0,999 9 which may result from a BER = 2,0 × 10-2 as used for test, a
reasonable number CF of frames to be transmitted is 100 000, i.e. 10 frames may be error-free on
average. The very large number of frames to be transmitted is to be able at all to estimate the BER,
as a small variation in erroneous frames may change significantly the corresponding estimated
BER.

ETSI
 53 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

B.4.3.2 Equipment
FER measurements can be easily conducted using the set of test messages TM1. Thus standard DSRC equipment might
be used, if the following software configuration has been implemented:

• initialization with BST and VST is implemented; see CEN EN 12795 [7] and CEN EN 12834 [8];

• the EFC command ECHO is implemented; see ISO 14906 [9].

In case of a bit error performance measurement of the RSU receiver, the following additional configuration
requirements apply:

• An [Link] transmitted by the RSU and not responded by the OBU under test shall be treated as "never
transmitted", as in this case the [Link] was received erroneous.

• An erroneous [Link] received shall not result in a retransmission of the related [Link] as
normally required by the DSRC protocol, but shall just lead to an increment of the frame error counter.

In case of a bit error performance measurement of the OBU receiver, the following additional configuration
requirements apply:

• An [Link] transmitted by the RSU and not responded by the OBU under test shall not result in a
retransmission of the related [Link] as normally required by the DSRC protocol, but shall just lead to
an increment of the frame error counter.

• An erroneous [Link] received shall not result in a retransmission of the related [Link] as
normally required by the DSRC protocol, but shall just be ignored, as in this case the [Link] was
received error free at the OBU under test.

B.4.3.3 Procedure
1) The RSU shall perform initialization with the OBU under test by exchanging BST and VST. The signal level
at the receiver input relevant for BER measurement shall be set to the level required for the test. The signal
level at the other receiver input shall be set at a reasonable high value as declared by the manufacturer such
that error free reception is very likely. In the unexpected case of transmission errors, the initialization attempt
shall be repeated. During initialization any additional interfering signals as requested by a specific test
procedure shall be switched off.

2) The RSU shall transmit a single ECHO command of maximum length. Reception of the corresponding
response from the OBU under test is expected to be error free. In case of errors, repetitions of the ECHO
command according to the DSRC protocol shall happen. This finalizes initialization.

In case of a bit error performance measurement of the RSU receiver, the following additional procedural steps shall be
processed:

3) Repeat step 2 CF times, CF see clause B.4.3.1, and report the total number CE of erroneous [Link]
frames received by the RSU. Calculate the actual Frame Error Ratio FER = CE / CF. Continue with step 5.

In case of a bit error performance measurement of the OBU receiver, the following additional procedural steps shall be
processed:

4) Repeat step 2 for CF times, CF see clause B.4.3.1, and report the total number CE of [Link] frames
not received by the RSU. Calculate the actual Frame Error Ratio FER = CE / CF.

5) Calculate BER out of FER according to clause B.4.3.1.

ETSI
 54 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

Annex C (informative):
Guidance on declaring the environmental profile
C.1 Recommended environmental profile
The requirements of the present document should apply under the environmental profile for intended operation, either
normal or extreme environmental conditions, which are recommended to be selected by the manufacturer in accordance
with clause C.2 and clause C.3.

C.2 Normal environmental conditions

The normal temperature and humidity conditions for tests should be any convenient combination of temperature and
relative humidity within the following ranges:

- temperature: +15 ºC to +35 ºC;

- relative humidity: 20 % to 75 %.

C.3 Extreme environmental conditions

Extreme environmental conditions are classified in categories according to table C.1.

Table C.1: Extreme environmental conditions

Temperature category RSU OBU

Category I (General): temperature: -20 °C to +55 °C temperature: -20 °C to +55 °C
Category ll: IEC 60721-3-4 [5] / 4K2 IEC 60721-3-5 [6] / 5K2
Category III IEC 60721-3-4 [5] / 4K3 IEC 60721-3-5 [6] / 5K3
Category IV: IEC 60721-3-4 [5] / 4K4 IEC 60721-3-5 [6] / 5K4

The extreme environmental conditions for tests should be any convenient selection of environmental parameter values,
except temperature, of a single category. For tests at extreme temperature, measurements should be made at both, the
upper and lower temperature of the selected category.

ETSI
 55 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

Annex D (informative):
Bibliography
• Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a procedure
for the provision of information in the field of technical standards and regulations.

• ETSI EN 301 489: "Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic
Compatibility (EMC) standard for radio equipment and services".

• ETSI EG 203 336: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Guide for the
selection of technical parameters for the production of Harmonised Standards covering article 3.1(b) and
article 3.2 of Directive 2014/53/EU".

ETSI
 56 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

Annex E (informative):
Change History
Version Information about changes
First published version covering Directive 2014/53/EU [i.5].
2.1.1
Receiver selectivity characteristics have become an essential requirement.

ETSI
 57 Draft ETSI EN 300 674-2-2 V2.0.3 (2016-03)

History
Document history
V1.1.1 February 1999 Publication as ETSI EN 300 674

V1.1.1 February 1999 Publication as ETSI ES 200 674-2

V1.1.1 August 2004 Publication

V2.0.3 March 2016 EN Approval Procedure AP 20160607: 2016-03-09 to 2016-06-07

ETSI