BATTERY CHARGER
INSTRUCTION MANUAL
Thank you for purchasing our product, please read
the manual carefully before using.
CATALOGUE
1、 BRIEF
2、 PANEL DIAGRAM
3、 ELECTRIC DIAGRAM
4、 INSTALLATION AND USE
1、 BRIEF
The purpose of the machine is to charge lead-acid
battery that suitable for automobiles power supply.
User should choose the right output voltage for
different battery，12V or 24V.
The battery charger has a temperature protection
inside machine and it will stop when it is overheated.
It will rework when the temperature debase.
Note: When the charger is over-current the fuse
will be broken, and the user have to replace a spare
fuse before using it again.
Input Output Battery
Model
Voltage/Frq Voltage Current Fuse Capacity
CB-30 30A 30A 30-300Ah
CB-40 40A 40A 40-400Ah
CB-50 240V/AC 12/24V 50A 50A 50-500Ah
CB-30A 50/60HZ DC 30A 30A 90-220Ah
CB-40A 40A 40A 120-320Ah
CB-50A 50A 50A 150-420Ah
The CB-30,CB-40 & CB-50“BCB30,BCB40 & BCB50” are normal
charger. While CB-30A,CB-40A & CB-50A“BCB30STR,BCB40STR &
BCB50STR”are with jump start function.
2.PANEL DIAGRAM of 30A,40A & 50A with
Jump Start function“BCB30STR,BCB40STR
& BCB50STR”
1.Handle
2.Output current ammeter
3a. Over-current protection
3b. Functional switch
(Turn on switch to start charging;
Turn on switch to jump start.)
4.Big/Small 7.Electric clamp
switchover 8.Input cable
5.12V/24V switch 9.Shell
6.Power fuse
PANEL DIAGRAM of 30A,40A & 50A without
Jump Start function“BCB30,BCB40 &
BCB50”
1.Handle 2.Output current ammeter
3.Over-current protection
4.Big/Small switchover
5.12V/24V switch 6.Power fuse
7.Electricize clamp 8.Input cable
9.Shell
3.ELECTRIC DIAGRAM
4.INSTALLATION AND USE
1、 Locate the battery charger properly and do not
expose on direct sunlight, set it in
less-vibration, clean and dry place, less of
iron-powder dust.
2、 Do not put the machine on wet place while using,
it may cause electric shock.
3、 Before using, please clean the touch point.
Connect the red clamp with battery anode, and
connect the black with battery cathode. Put
the plug into 240V/50Hz jack. Last you can see
the current on ammeter.
4、 Up keeping and repair if no output current
examine as below
A. Examine the 12V/24V switch if corresponds to the
correct location.
B. Over-current protection settings.
C. Replacement of fuse.
D. Oxide on storage battery ‘anode’ or ‘cathode’
if still no current after the examination above
please contact with the factory.
Note:
1. The polarity of power Output can’t be opposite
or short circuit.
2. Do not block aerate hole of battery casing.
3. If the battery temperature is too high, the user
needs to switch to ‘MIN’ charging or stop the
machine immediately by switching off.
This is the ammeter, when the battery is fully charge
the ammeter goes to zero.
Warning:
1、 It is forbidden to jump start a "flat battery”,
You have to charge the flat battery at least 15minutes
before jump starting.
2、 When charging, the battery must be in a ventilate
condition.
3、 When charging in the car, please do as following:
a、 First connect the battery charger to the car
battery.
b、 Make sure the connect point should be far from
battery and fuel.
c、 Connect the charger to power supply.
d、 After charging, cut off the power before
removing the connectors from the car battery.
e、 MAX settings will charge faster but it may
shortens the life of the battery. MIN settings will
charge slower but good for battery.
