Scribd
Upload
70 views1 page

Jotun Hardtop AS Thinner Data Sheet

Hardtop AS is a two-component, polyamine cured epoxy coating. It has a pot life of 4 hours at 23°C. For thinning and cleaning, Jotun Thinner No. 10 provides fast evaporation while Jotun Thinner No. 25 provides slow evaporation. Drying times range from 1.5 hours for surface dry at 23°C to 20 days for service at 0°C. The product can be sprayed using airless or air spray methods, with recommended nozzle tips and pressures provided.

Uploaded by

TamerTamer
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
70 views1 page

Jotun Hardtop AS Thinner Data Sheet

Hardtop AS is a two-component, polyamine cured epoxy coating. It has a pot life of 4 hours at 23°C. For thinning and cleaning, Jotun Thinner No. 10 provides fast evaporation while Jotun Thinner No. 25 provides slow evaporation. Drying times range from 1.5 hours for surface dry at 23°C to 20 days for service at 0°C. The product can be sprayed using airless or air spray methods, with recommended nozzle tips and pressures provided.

Uploaded by

TamerTamer
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd

Technical Data Sheet

Hardtop AS

Thinner/Cleaning solvent
Thinner: Jotun Thinner No. 10 / Jotun Thinner No. 25

Jotun Thinner No. 10 for fast evaporation.


Jotun Thinner No. 25 for slow evaporation.

Guiding data for airless spray


Nozzle tip (inch/1000): 13-19

Pressure at nozzle (minimum): 150 bar/2100 psi

Guiding data for air spray


Nozzle tip (inch/1000): 11-19 (HVLP) / 1.1-1.9 mm (pressure pot)
Pressure at nozzle (minimum): 2.1 bar/30 psi (HVLP) / 2.1 bar/30 psi (pressure pot)

Drying and Curing time


Substrate temperature 0 °C 5 °C 10 °C 23 °C 40 °C

Surface (touch) dry 8h 4h 2h 1 h 30 min


Walk-on-dry 40 h 30 h 16 h 8 h 4h
Dry to over coat, minimum 24 h 18 h 10 h 5 h 2.5 h
Dried/cured for service 20 d 15 d 10 d 5 d 2d

Drying and curing times are determined under controlled temperatures and relative humidity below 85 %, and
at average of the DFT range for the product.

Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal
tackiness.

Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks,
imprints or other physical damage.

Dry to over coat, minimum: The shortest time allowed before the next coat can be applied.

Dried/cured for service: Minimum time before the coating can be permanently exposed to the intended
environment/medium.

Induction time and Pot life


Paint temperature 23 °C

Pot life 4h

Date of issue: 7 November 2016 Page: 3/5

This Technical Data Sheet supersedes those previously issued.


The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at [Link]

You might also like