List of packaging standards developed by ISO:

ISO 186:2002, Paper and board -- Sampling to determine average quality

ISO 187:1990, Paper, board and pulps -- Standard atmosphere for conditioning and testing and
procedure for monitoring the atmosphere and conditioning of samples
ISO/TS 210:2014, Essential oils -- General rules for packaging, conditioning and storage
ISO 217:2013, Paper -- Untrimmed sizes -- Designation and tolerances for primary and
supplementary ranges, and indication of machine direction
ISO 287:2009, Paper and board -- Determination of moisture content of a lot -- Oven-drying
method
ISO 534:2011, Paper and board -- Determination of thickness, density and specific volume
ISO 535:2014. Paper and board -- Determination of water absorptiveness -- Cobb method
ISO 536:2012, Paper and board -- Determination of grammage
ISO 638:2008, Paper, board and pulps -- Determination of dry matter content -- Oven-drying
method
ISO 780:1997, Packaging -- Pictorial marking for handling of goods
ISO 1924-1:1992, Paper and board -- Determination of tensile properties -- Part 1: Constant rate of
loading method
ISO 1924-2:2008, Paper and board -- Determination of tensile properties -- Part 2: Constant rate of
elongation method (20 mm/min)
ISO 1924-3:2005, Paper and board -- Determination of tensile properties -- Part 3: Constant rate of
elongation method (100 mm/min)
ISO 1974:2012, Paper -- Determination of tearing resistance -- Elmendorf method
ISO 2144:2015, Paper, board and pulps -- Determination of residue (ash) on ignition at 900
degrees C
ISO 2206: 1987, Packaging -- Complete, filled transport packages -- Identification of parts when
testing
ISO 2233:2000, Packaging -- Complete, filled transport packages and unit loads -- Conditioning for
testing
ISO 2234:2000, Packaging -- Complete, filled transport packages and unit loads -- Stacking tests
using a static load
ISO 2244:2000, Packaging -- Complete, filled transport packages and unit loads -- Horizontal
impact tests
ISO 2247:2000, Packaging -- Complete, filled transport packages and unit loads -- Vibration tests
at fixed low frequency
ISO 2248:1985, Packaging -- Complete, filled transport packages -- Vertical impact test by
dropping
ISO 2469:2014, Paper, board and pulps -- Measurement of diffuse radiance factor (diffuse
reflectance factor)
ISO 2470-1:2009, Paper, board and pulps -- Measurement of diffuse blue reflectance factor -- Part
1: Indoor daylight conditions (ISO brightness)
ISO 2470-2:2008, Paper, board and pulps -- Measurement of diffuse blue reflectance factor -- Part
2: Outdoor daylight conditions (D65 brightness)
ISO 2471:2008, Paper and board -- Determination of opacity (paper backing) -- Diffuse reflectance
method
ISO 2493-1:2010, Paper and board -- Determination of bending resistance -- Part 1: Constant rate
of deflection
ISO 2493-2:2011, Paper and board -- Determination of bending resistance -- Part 2: Taber-type
tester

1
ISO 2528:1995, Sheet materials -- Determination of water vapour transmission rate -- Gravimetric
(dish) method
ISO 2758:2014, Paper -- Determination of bursting strength
ISO 2759:2014, Board -Determination of bursting strength
ISO 2873:2000, Packaging -- Complete, filled transport packages and unit loads -- Low pressure
test
ISO 2875:2000, Packaging -- Complete, filled transport packages and unit loads -- Water-spray
test
ISO 2876:1985, Packaging -- Complete, filled transport packages -- Rolling test
ISO 3034:2011, Corrugated fibreboard -- Determination of single sheet thickness
ISO 3035:2011, Corrugated fibreboard -- Determination of flat crush resistance
ISO 3036:1975, Board -- Determination of puncture resistance
ISO 3037:2013, Corrugated fibreboard -- Determination of edgewise crush resistance (unwaxed
edge method)
ISO 3038:1975, Corrugated fibreboard -- Determination of the water resistance of the glue bond
by immersion
ISO 3039:2010, Corrugated fibreboard -- Determination of grammage of the component papers
after separation
ISO 3394:2012, Packaging -- Complete, filled transport packages and unit loads -- Dimensions of
rigid rectangular packages
ISO 3676:2012, Packaging -- Complete, filled transport packages and unit loads -- Unit load
dimensions
ISO 3689:1983, Paper and board -- Determination of bursting strength after immersion in water
ISO 3781:2011, Paper and board -- Determination of tensile strength after immersion in water
ISO 3783:2006, Paper and board -- Determination of resistance to picking -- Accelerated speed
method using the IGT-type tester (electric model)
ISO 3863:1989, Cylindrical cork stoppers -- Dimensional characteristics, sampling, packaging and
marking
ISO 3869:2001,Composition cork -- Expansion joint fillers -- Specifications, packaging and marking
ISO 4046-1:2002, Paper, board, pulps and related terms -- Vocabulary -- Part 1: Alphabetical
index
ISO 4046-2:2002, Paper, board, pulps and related terms -- Vocabulary -- Part 2: Pulping
terminology
ISO 4046-3:2002, Paper, board, pulps and related terms -- Vocabulary -- Part 3: Paper-making
terminology
ISO 4046-4:2002, Paper, board, pulps and related terms -- Vocabulary -- Part 4: Paper and board
grades and converted products
ISO 4046-5:2002, Paper, board, pulps and related terms -- Vocabulary -- Part 5: Properties of
pulp, paper and board
ISO 4094:2005, Paper, board and pulps -- International calibration of testing apparatus --
Nomination and acceptance of standardizing and authorized laboratories
ISO 4178:1980, Complete, filled transport packages -- Distribution trials -- Information to be
recorded
ISO 4707:1981, Cork -- Stoppers -- Sampling for inspection of dimensional characteristics
ISO 4709:2000, Composition cork -- Gasket material -- Classification system, requirements,
sampling, packaging and marking
ISO 4710:2000, Cork -- Cylindrical stoppers for sparkling wines and gasified wines --
Characteristics

2
ISO 4714:2000, Composition cork -- Specifications, sampling, packaging and marking
ISO 4180:2009, Packaging -- Packaging -- Complete, filled transport packages -- General rules for
the compilation of performance test schedule
ISO 5495:2005, Sensory analysis -- Methodology -- Paired comparison testISO 5626:1993, Paper
-- Determination of folding endurance
ISO 5627:1995, Paper and board -- Determination of smoothness (Bekk method)
ISO 5628:2012, Paper and board -- Determination of bending stiffness -- General principles for
two-point, three-point and four-point methods
ISO 5629:1983, Paper and board -- Determination of bending stiffness -- Resonance method
ISO 5630-1:1991, Paper and board -- Accelerated ageing -- Part 1: Dry heat treatment at 105
degrees C
ISO 5630-2:1985, Paper and board -- Accelerated ageing -- Part 2: Moist heat treatment at 90
degrees C and 25 % relative humidity
ISO 5630-3:1996, Paper and board -- Accelerated ageing -- Part 3: Moist heat treatment at 80
degrees C and 65 % relative humidity
ISO 5630-4:1986, Paper and board -- Accelerated ageing -- Part 4: Dry heat treatment at 120 or
150 degrees C
ISO 5630-5:2008, Paper and board -- Accelerated ageing -- Part 5: Exposure to elevated
temperature at 100 degrees C
ISO 5630-6:2009, Paper and board -- Accelerated ageing -- Part 6: Exposure to atmospheric
pollution (nitrogen dioxide)
ISO 5630-7:2014, Paper and board -- Accelerated ageing -- Part 7: Exposure to light
ISO 5631-1:2009, Paper and board -- Determination of colour by diffuse reflectance -- Part 1:
Indoor daylight conditions (C/2 degrees)
ISO 5631-2:2014, Paper and board -- Determination of colour by diffuse reflectance -- Part 2:
Outdoor daylight conditions (D65/10 degrees)
ISO 5631-3:2014, Paper and board -- Determination of colour by diffuse reflectance -- Part 3:
Indoor illumination conditions (D50/2 degrees)
ISO 5647:1990, Paper and board -- Determination of titanium dioxide content
ISO 6587:1992, Paper, board and pulps -- Determination of conductivity of aqueous extracts
ISO 6588-1:2012, Paper, board and pulps -- Determination of pH of aqueous extracts -- Part 1:
Cold extraction
ISO 6588-2:2012, Paper, board and pulps -- Determination of pH of aqueous extracts -- Part 2:
Hot extraction
ISO 6590-1:1983, Packaging -- Sacks -- Vocabulary and types -- Part 1: Paper sacks
ISO 6590-2:1986. Packaging -- Sacks -- Vocabulary and types -- Part 2: Sacks made from
thermoplastic flexible film
ISO 6591-1:1984, Packaging -- Sacks -- Description and method of measurement -- Part 1: Empty
paper sacks
ISO 6591-2:1985, Packaging -- Sacks -- Description and method of measurement -- Part 2: Empty
sacks made from thermoplastic flexible film
ISO 6599-1:1983, Packaging -- Sacks -- Conditioning for testing -- Part 1: Paper sacks
ISO 5633:1983, Paper and board -- Determination of resistance to water penetration
ISO 5635:1978, Paper -- Measurement of dimensional change after immersion in water
ISO 5636-1:1984, Paper and board -- Determination of air permeance (medium range) -- Part 1:
General method
ISO 5636-3:2013, Paper and board -- Determination of air permeance (medium range) -- Part 3:
Bendtsen method

3
ISO 5636-4:2013, Paper and board -- Determination of air permeance (medium range) -- Part 4:
Sheffield method
ISO 5636-5:2013, Paper and board -- Determination of air permeance (medium range) -- Part 5:
Gurley method
ISO 5636-6:2015, Paper and board -- Determination of air permeance (medium range) -- Part 6:
Oken method
ISO 5637:1989, Paper and board -- Determination of water absorption after immersion in water
ISO 5638:1978, Solid fibreboard -- Determination of grammage of single layers
ISO 6383-1:1983, Plastics -- Film and sheeting -- Determination of tear resistance -- Part 1:
Trouser tear method
ISO 6383-2:1983, Plastics -- Film and sheeting -- Determination of tear resistance -- Part 2:
Elmendorf method
ISO 7023:1983, Packaging -- Sacks -- Method of sampling empty sacks for testing
ISO 7348:1992, Glass containers -- Manufacture – Vocabulary
ISO 7458:2004, Glass containers -- Internal pressure resistance -- Test methods
ISO 7459:2004, Glass containers -- Thermal shock resistance and thermal shock endurance --
Test methods
ISO 7263:2011, Corrugating medium -- Determination of the flat crush resistance after laboratory
fluting
ISO 7765-1:1988, Plastics film and sheeting -- Determination of impact resistance by the free-
falling dart method -- Part 1: Staircase methods
ISO 7765-2:1994, Plastics film and sheeting -- Determination of impact resistance by the free-
falling dart method -- Part 2: Instrumented puncture test
ISO 7965-1:1984, Packaging -- Sacks -- Drop test -- Part 1: Paper sacks
ISO 7965-2:1993, Sacks -- Drop test -- Part 2: Sacks made from thermoplastic flexible film
ISO 8106:2004, Glass containers -- Determination of capacity by gravimetric method -- Test
method
ISO 8226-1:1994, Paper and board -- Measurement of hygroexpansivity -- Part 1:
Hygroexpansivity up to a maximum relative humidity of 68 %
ISO 8226-2:1990, Paper and board -- Measurement of hygroexpansivity -- Part 2:
Hygroexpansivity up to a maximum relative humidity of 86 %
ISO 8254-1:2009, Paper and board -- Measurement of specular gloss -- Part 1: 75 degree gloss
with a converging beam, TAPPI method
ISO 8254-2:2003, Paper and board -- Measurement of specular gloss -- Part 2: 75 degree gloss
with a parallel beam, DIN method
ISO 8254-3:2004, Paper and board -- Measurement of specular gloss -- Part 3: 20 degree gloss
with a converging beam, TAPPI method
ISO 8317:2003, Child-resistant packaging -- Requirements and testing procedures for reclosable
packages
ISO 8318:2000, Packaging -- Complete, filled transport packages and unit loads -- Sinusoidal
vibration tests using a variable frequency
ISO 8351-1:1994, Packaging -- Method of specification for sacks -- Part 1: Paper sack
ISO 8351-2:1994, Packaging -- Method of specification for sacks -- Part 2: Sacks made from
thermoplastic flexible film
ISO 8367-1:1993, Packaging -- Dimensional tolerances for general purpose sacks -- Part 1: Paper
sacks
ISO 8367-2:1993, Packaging -- Dimensional tolerances for general purpose sacks -- Part 2: Sacks

4
made from thermoplastic flexible film
ISO 8362-4:2011, Injection containers and accessories -- Part 4: Injection vials made of moulded
glass
ISO 8474:1986, Packaging -- Complete, filled transport packages -- Water immersion test
ISO 8768: 1987, Packaging -- Complete, filled transport packages -- Toppling test
ISO 8784-1:2014, Pulp, paper and board -- Microbiological examination -- Part 1: Enumeration of
bacteria and bacterial spores based on disintegration
ISO 8787:1986, Paper and board -- Determination of capillary rise -- Klemm method
ISO 8791-1:1986, Paper and board -- Determination of roughness/smoothness (air leak methods)
-- Part 1: General method
ISO 8791-2:2013, Paper and board -- Determination of roughness/smoothness (air leak methods)
-- Part 2: Bendtsen method
ISO 8791-3:2005, Paper and board -- Determination of roughness/smoothness (air leak methods)
-- Part 3: Sheffield method
ISO 8791-4:2007, Paper and board -- Determination of roughness/smoothness (air leak methods)
-- Part 4: Print-surf method
ISO 9008:1991, Glass bottles -- Verticality -- Test method
ISO 9057:1991, Glass containers -- 28 mm tamper-evident finish for pressurized liquids –
Dimensions
ISO 9058:2008, Glass containers -- Standard tolerances for bottles
ISO 9184-1:1990, Paper, board and pulps -- Fibre furnish analysis -- Part 1: General method
ISO 9184-2:1990, Paper, board and pulps -- Fibre furnish analysis -- Part 2: Staining guide
ISO 9184-3:1990, Paper, board and pulps -- Fibre furnish analysis -- Part 3: Herzberg staining test
ISO 9184-4:1990, Paper, board and pulps -- Fibre furnish analysis -- Part 4: Graff "C" staining test
ISO 9184-5:1990, Paper, board and pulps -- Fibre furnish analysis -- Part 5: Lofton-Merritt staining
test (modification of Wisbar)
ISO 9184-6:1994, Paper, board and pulps -- Fibre furnish analysis -- Part 6: Determination of fibre
coarseness
ISO 9184-7:1994, Paper, board and pulps -- Fibre furnish analysis -- Part 7: Determination of
weight factor
ISO 9197:2006, Paper, board and pulps -- Determination of water-soluble chlorides
ISO 9198:2001, Paper, board and pulp -- Determination of water-soluble sulfates
ISO 9416:2009, Paper -- Determination of light scattering and absorption coefficients (using
Kubelka-Munk theory)
ISO 9706:1994, Information and documentation -- Paper for documents -- Requirements for
permanence
ISO 9884-1:1994, Tea sacks -- Specification -- Part 1: Reference sack for palletized and
containerized transport of tea
ISO 9884-2:1999, Tea sacks -- Specification -- Part 2: Performance specification for sacks for
palletized and containerized transport of tea
ISO 9895:2008, Paper and board -- Compressive strength -- Short-span test
ISO 9932:1990, Paper and board -- Determination of water vapour transmission rate of sheet
materials -- Dynamic sweep and static gas methods
ISO 10531:1992, Packaging -- Complete, filled transport packages -- Stability testing of unit loads
ISO/PRF TR 10688, Paper, board and pulps -- Basic terms and equations for optical properties
ISO 10716:1994, Paper and board -- Determination of alkali reserve
ISO 10775:2013, Paper, board and pulps -- Determination of cadmium content -- Atomic

5
absorption spectrometric method
ISO 11093-1:1994, Paper and board -- Testing of cores -- Part 1: Sampling
ISO 11093-2:1994, Paper and board -- Testing of cores -- Part 2: Conditioning of test samples
ISO 11093-3:1994, Paper and board -- Testing of cores -- Part 3: Determination of moisture
content using the oven drying method
ISO 11093-4:1997, Paper and board -- Testing of cores -- Part 4: Measurement of dimensions
ISO 11093-5:2009, Paper and board -- Testing of cores -- Part 5: Determination of characteristics
of concentric rotation
ISO 11093-6:2005, Paper and board -- Testing of cores -- Part 6: Determination of bending
strength by the three-point method
ISO 11093-7:2011, Paper and board -- Testing of cores -- Part 7: Determination of flexural
modulus by the three-point method
ISO 11093-8:2012, Paper and board -- Testing of cores -- Part 8: Determination of natural
frequency and flexural modulus by experimental modal analysis
ISO 11093-9:2006, Paper and board -- Testing of cores -- Part 9: Determination of flat crush
resistance
ISO 11156:2011, Packaging -- Accessible design -- General requirements
ISO 11357-1:2009, Plastics -- Differential scanning calorimetry (DSC) -- Part 1: General principles
ISO 11357-2:2013, Plastics -- Differential scanning calorimetry (DSC) -- Part 2: Determination of
glass transition temperature and glass transition step height
ISO 11357-3:2011, Plastics -- Differential scanning calorimetry (DSC) -- Part 3: Determination of
temperature and enthalpy of melting and crystallization
ISO 11357-4:2005, Plastics -- Differential scanning calorimetry (DSC) -- Part 4: Determination of
specific heat capacity
ISO 11357-5:2013, Plastics -- Differential scanning calorimetry (DSC) -- Part 5: Determination of
characteristic reaction-curve temperatures and times, enthalpy of reaction and degree of
conversion
ISO 11357-6:2008, Plastics -- Differential scanning calorimetry (DSC) -- Part 6: Determination of
oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT)
ISO 11357-7:2002, Plastics -- Differential scanning calorimetry (DSC) -- Part 7: Determination of
crystallization kinetics
ISO 11418-1:2005, Containers and accessories for pharmaceutical preparations -- Part 1: Drop-
dispensing glass bottles
ISO 11418-2:2005, Containers and accessories for pharmaceutical preparations -- Part 2: Screw-
neck glass bottles for syrups
ISO 11418-3:2005, Containers and accessories for pharmaceutical preparations -- Part 3: Screw-
neck glass bottles (veral) for solid and liquid dosage forms
ISO 11418-4:2005, Containers and accessories for pharmaceutical preparations -- Part 4: Tablet
glass bottles
ISO 11475:2004, Paper and board -- Determination of CIE whiteness, D65/10 degrees (outdoor
daylight)
ISO 11476:2010, Paper and board -- Determination of CIE whiteness, C/2 degrees (indoor
illumination conditions)
ISO 11480:1997, Pulp, paper and board -- Determination of total chlorine and organically bound
chlorine
ISO 11556:2005, Paper and board -- Determination of curl using a single vertically suspended test

6
piece
ISO 11607-1: 2006, Packaging for terminally sterilized medical devices -- Part 1: Requirements for
materials, sterile barrier systems and packaging systems.
ISO 11607-2: 2006, Packaging for terminally sterilized medical devices -- Part 2: Validation for
Forming, Sealing, and Assembly Processes
ISO 11664-1:2007 (CIE S 014-1/E:2006), Colorimetry -- Part 1: CIE standard colorimetric
observers
ISO 11664-2:2007 (CIE S 014-2/E:2006), Colorimetry -- Part 2: CIE standard illuminants
ISO 11683:1997, Packaging -- Tactile warnings of danger – Requirements
ISO 11897:1999, Packaging -- Sacks made from thermoplastic flexible film -- Tear propagation on
edge folds
ISO 11513:2011, Gas cylinders -- Refillable welded steel cylinders containing materials for sub-
atmospheric gas packaging (excluding acetylene) -- Design, construction, testing, use and periodic
inspection
ISO 12048:1994, Packaging -- Complete, filled transport packages -- Compression and stacking
tests using a compression tester
ISO 12192:2011, Paper and board -- Determination of compressive strength -- Ring crush method
ISO 12625-1:2011, Tissue paper and tissue products -- Part 1: General guidance on terms
ISO 12625-3:2014, Tissue paper and tissue products -- Part 3: Determination of thickness, bulking
thickness and apparent bulk density and bulk
ISO 12625-4:2005, Tissue paper and tissue products -- Part 4: Determination of tensile strength,
stretch at break and tensile energy absorption
ISO 12625-5:2005, Tissue paper and tissue products -- Part 5: Determination of wet tensile
strength
ISO 12625-6:2005, Tissue paper and tissue products -- Part 6: Determination of grammage
ISO 12625-7:2014, Tissue paper and tissue products -- Part 7: Determination of optical properties
-- Measurement of brightness and colour with D65/10° (outdoor daylight)
ISO 12625-8:2010, Tissue paper and tissue products -- Part 8: Water-absorption time and water-
absorption capacity, basket-immersion test method
ISO 12625-9:2015, Tissue paper and tissue products -- Part 9: Determination of ball burst strength
ISO 12625-11:2012, Tissue paper and tissue products -- Part 11: Determination of wet ball burst
strength
ISO 12625-12:2010, Tissue paper and tissue products -- Part 12: Determination of tensile strength
of perforated lines -- Calculation of perforation efficiency
ISO 12625-15:2015, Tissue paper and tissue products -- Part 15: Determination of optical
properties -- Measurement of brightness and colour with C/2° (indoor daylight) illuminant
ISO 12625-16:2015, Tissue paper and tissue products -- Part 16: Determination of optical
properties -- Opacity (paper backing) -- Diffuse reflectance method
ISO 12821:2013 , Glass packaging -- 26 H 180 crown finish – Dimensions
ISO 12818:2013, Glass packaging -- Standard tolerances for flaconnage
ISO 12822:2015, Glass packaging -- 26 H 126 crown finish – Dimensions
ISO 12830:2011, Paper, board and pulps -- Determination of acid-soluble magnesium, calcium,
manganese, iron, copper, sodium and potassium
ISO 13106:2014, Plastics -- Blow-moulded polypropylene containers for packaging of liquid
foodstuffs
ISO 13127:2012, Packaging -- Child resistant packaging -- Mechanical test methods for reclosable
child resistant packaging systems
ISO 13274:2013, Packaging -- Transport packaging for dangerous goods -- Plastics compatibility

7
testing for packaging and IBCs
ISO 13302:2003, Sensory Analysis – Methods for assessing modifications to the flavour of
foodstuffs due to packaging
ISO 13355:2001, Packaging -- Complete, filled transport packages and unit loads -- Vertical
random vibration test
ISO 13542:2006, Paper and board -- Specification for internal diameters of cores for reels
ISO 13820:2014, Paper, board and corrugated fibreboard -- Description and calibration of
compression-testing equipment
ISO 13821:2002, Corrugated fibreboard -- Determination of edgewise crush resistance -- Waxed
edge method
ISO 14968:1999, Paper and board -- Cut-size office paper -- Measurement of curl in a pack of
sheets
ISO 15119:2000, Packaging -- Sacks -- Determination of the friction of filled sacks
ISO 15318:1999, Pulp, paper and board -- Determination of 7 specified polychlorinated biphenyls
(PCB)
ISO 15320:2011, Pulp, paper and board -- Determination of pentachlorophenol in an aqueous
extract
ISO 15359:1999, Paper and board -- Determination of the static and kinetic coefficients of friction -
- Horizontal plane method
ISO 15378:2011, Primary packaging materials for medicinal products -- Particular requirements for
the application of ISO 9001:2008, with reference to Good Manufacturing Practice (GMP)
ISO 15394:2009, Packaging -- Bar code and two-dimensional symbols for shipping, transport and
receiving labels
ISO 15750-1:2002, Packaging -- Steel drums -- Part 1: Removable head (open head) drums with a
minimum total capacity of 208 l, 210 l and 216,5 l
ISO 15750-2:2002, Packaging -- Steel drums -- Part 2: Non-removable head (tight head) drums
with a minimum total capacity of 212 l, 216,5 l and 230 l
ISO 15750-3:2002, Packaging -- Steel drums -- Part 3: Inserted flange-type closure systems
ISO 15754:2009, Paper and board -- Determination of z-directional tensile strength
ISO 15755:1999, Paper and board -- Estimation of contraries
ISO 15987:2003, Plastics -- Film and sheeting -- Biaxially oriented polyamide (nylon) films
ISO 15988:2003, Plastics -- Film and sheeting -- Biaxially oriented poly(ethylene terephthalate)
(PET) films
ISO 15867:2003, Intermediate bulk containers (IBCs) for non-dangerous goods – Terminology
ISO 16101:2004, Packaging -- Transport packaging for dangerous goods -- Plastics compatibility
testing
ISO 16103:2005, Packaging -- Transport packaging for dangerous goods -- Recycled plastics
material
ISO 16104:2003, Packaging -- Transport packaging for dangerous goods -- Test methods
ISO 16106:2006, Packaging -- Transport packages for dangerous goods -- Dangerous goods
packagings, intermediate bulk containers (IBCs) and large packagings -- Guidelines for the
application of ISO 9001
ISO/TR 16218:2013, Packaging and the environment -- Processes for chemical recovery
ISO/DIS 16260.2, Paper and board -- Determination of internal bond strength
ISO 16495:2013, Packaging -- Transport packaging for dangerous goods -- Test methods
ISO 16532-1:2008, Paper and board -- Determination of grease resistance -- Part 1: Permeability
test
ISO 16532-2:2007, Paper and board -- Determination of grease resistance -- Part 2: Surface

8
repellency test
ISO 16532-3:2010, Paper and board -- Determination of grease resistance -- Part 3: Turpentine
test for voids in glassine and greaseproof papers
ISO/TS 16775:2014, Packaging for terminally sterilized medical devices -- Guidance on the
application of ISO 11607-1 and ISO 11607-2
ISO 16820:2004, Sensory analysis -- Methodology -- Sequential analysis
ISO 16883:2007, Packaging -- Transport packages for dangerous goods -- Test methods for large
packagings.
ISO 16945:2014, Corrugating medium -- Determination of the edge crush resistance after
laboratory fluting
ISO/TR 17098:2013, Packaging material recycling -- Report on substances and materials which
may impede recycling
ISO 17351:2013, Packaging -- Braille on packaging for medicinal products
ISO 17363:2013, Supply chain applications of RFID -- Freight containers
ISO 17364:2013, Supply chain applications of RFID -- Returnable transport items (RTIs) and
returnable packaging items (RPIs)
ISO 17365:2013, Supply chain applications of RFID -- Transport units
ISO 17366:2013, Supply chain applications of RFID -- Product packaging
ISO 17367:2013, Supply chain applications of RFID -- Product tagging
ISO/TR 17370:2013, Application Guideline on Data Carriers for Supply Chain Management
ISO/DIS 17451-1, Packaging -- Codification of contents for inventories for shipments of household
goods and personal effects -- Part 1: Alphanumeric codification of inventories and manifests
ISO 17480:2015, Packaging -- Accessible design -- Ease of opening
ISO 17555:2003, Plastics -- Film and sheeting -- Biaxially oriented polypropylene (PP) films
ISO 17557:2003, Plastics -- Film and sheeting -- Cast polypropylene (PP) films
ISO 17812:2007, Paper, board and pulps -- Determination of total magnesium, total calcium, total
manganese, total iron and total copper
ISO/TS 17958:2013, Paper and board -- Determination of fracture toughness -- Constant rate of
elongation method (1,7 mm/s)
ISO 18263-1:2015, Plastics -- Mixtures of polypropylene (PP) and polyethylene (PE) recyclate
derived from PP and PE used for flexible and rigid consumer packaging -- Part 1: Designation
system and basis for specification
ISO/FDIS 18263-2, Plastics -- Mixtures of polypropylene (PP) and polyethylene (PE) recyclate
derived from PP and PE used for flexible and rigid consumenr packaging -- Part 2: Preparation of
test specimens and determination of properties
ISO/DIS 18522, Paper and board - Automated off-line testing of physical properties for CD (cross
direction) profiles
ISO 18601:2013, Packaging and the environment -- General requirements for the use of ISO
standards in the field of packaging and the environment
ISO 18602:2013, Packaging and the environment -- Optimization of the packaging system
ISO 18603:2013, Packaging and the environment – Reuse
ISO 18604:2013, Packaging and the environment -- Material recycling
ISO 18605:2013, Packaging and the environment -- Energy recovery
ISO 18606:2013, Packaging and the environment -- Organic recycling
ISO/CD 19709-1, Transport packaging -- Small load container systems -- Part 1: Common
requirements and test methods
ISO/DTS 19709-2, Transport packaging -- Small load container systems -- Part 2: Column

9
Stackable System (CSS)
ISO/DTS 19709-3 , Transport packaging -- Small load container systems -- Part 3: Bond Stackable
System (BSS)
ISO/PRF TS 20460, Paper and board -- Automated on-line testing -- Metrological comparability
between standardized measurements and output of on-line gauges
ISO 20848-1:2006, Packaging -- Plastics drums -- Part 1: Removable head (open head) drums
with a nominal capacity of 113,6 l to 220 l
ISO 20848-2:2006, Packaging -- Plastics drums -- Part 2: Non-removable head (tight head) drums
with a nominal capacity of 208,2 l and 220 l
ISO 20848-3:2006, Packaging -- Plastics drums -- Part 3: Plug/bung closure systems for plastics
drums with a nominal capacity of 113,6 l to 220 l
ISO 21067:2007, Packaging – Vocabulary
ISO/DIS 21067-1, Packaging -- Vocabulary -- Part 1: General terms
ISO/DIS 21067-2, Packaging -- Vocabulary -- Part 2: Packaging and the environment terms
ISO 21898:2004, Packaging -- Flexible intermediate bulk containers (FIBCs) for non-dangerous
goods
ISO/TS 22002-4:2013, Prerequisite programmes on food safety -- Part 4: Food packaging
manufacturing
ISO 22742:2010, Packaging -- Linear bar code and two-dimensional symbols for product
packaging
ISO 22715:2006, Cosmetics -- Packaging and labelling
ISO 22754:2008, Pulp and paper -- Determination of the effective residual ink concentration (ERIC
number) by infrared reflectance measurement
ISO 22891:2013, Paper -- Determination of transmittance by diffuse reflectance measurement
ISO 23560:2015, Woven polypropylene sacks for bulk packaging of foodstuffs
ISO/IEC TR 24729-1:2008, Information technology -- Radio frequency identification for item
management -- Implementation guidelines -- Part 1: RFID-enabled labels and packaging
supporting ISO/IEC 18000-6C
ISO/AWI TR 24498, Paper, board and pulps -- Estimation of uncertainty for test methods
ISO 28219:2009, Packaging -- Labelling and direct product marking with linear bar code and two-
dimensional symbols
IEC 61340-4-4:2005, Electrostatics -- Part 4-4: Standard test methods for specific applications -
Electrostatic classification of flexible intermediate bulk containers (FIBC)
ISO/IEC Guide 41:2003, Packaging -- Recommendations for addressing consumer needs

10