A01 A02
Inspection certificate 3.1+PED PN-EN 10204 1/1
A03
Document No 2020/10/16574 Z02 Date 2020-10-15
A04 A05
Manufacturer's mark Quality Assurance Department
A06.1 Customer Mick d.o.o
NIP: 865-00-13-543 kukuljanovo 447, 51227 kukuljanovo
Władysława Grabskiego 38 A06.2 Consignee Mick d.o.o
37-450 Stalowa Wola kukuljanovo 447, 51227 kukuljanovo
POLAND A06.3 Receiver of the document Mick d.o.o
PN-EN ISO 9001:2001 kukuljanovo 447, 51227 kukuljanovo
cert. Nr CSJ/115/2016 Purchaser's order Manufakturer's
A07 A08 2104
cert. Nr 01 202 PL/Q-13 0846 number works order num
B01 / B09 - B11 Product description B08 Quantity in psc
Cap - PN-EN 10253-2 TYP B - 168.3 x 4.5 15
B02 Steel and standard B07 Heat No
PN-EN 10253-2 TYP B ; Opc.9 ,AD 2000 W4 ; P265GH / EN 10028-2 ; 10601
B04 Delivery Condition/forming metod B12 Theoretical mass
Normalized 890/20 pow
B06 Marking KJ 168.3x4.5 PL F P265GH 10601 S DIN EN2 B
B14 Raw Material/Inspection certifikate of material
Plate according to the certificate 20/324276 01
B07 C71-C92 Chemical composition %
Heat No C Mn Si P S Cr Ni Cu Mo Al V Nb Ti N Sn B As CEV
10601 0.13 0.65 0.139 0.017 0.008 0.016 0.009 0.02 0.002 0.038 0.001 0.002 0.001 0.003 0.004 0 0.001 0.2441
Mechanical properties acc. ASME
C02 Direction of taking sample C33-C39 Diameter of the ball/weighting force
C00 C03 C11 C12 C13 C14 C30-C32
Test No Temp. °C Yield point Tensile strength Elongation Narrowing Hardness test on fitting
/MPa/ /MPa/ % Z% HBW
Result obtained
10601 21 ReH 299 412 A5 38
Impact test
C02 Direction of taking sample q - transverse C41 Size 2.5 x 10
C00 C03 C40 Mesaured value C44 value counted to standard measurements of
Test No Temp. °C Type of Unit C42 C42 C42 C43
specime 1 2 3 average Required 1 2 3 average
10601 -30 ISO-V J 24 24 24 24 96 96 96 96
D02-D99 Non-destructive and additional tests Standard Criterion
Z06 Suplementary confirmation
D01 Marking, surface and dimension checked - no objections. Z03 Work's Inspector stamp
Z01
Hereby we confirm that above-mentioned products became examined and realize requirements of given norms Z03 Work's Inspector
and order.
Z05 TASTA ARMATURA has a quality system in accordance with Directive 2014/68/EU Annex I section 4.3 -
Certificate CSJ/115/WM/PED/2016 and Certificate AD 2000-Merkblatt W0 No. 01 202 PL / Q-13 0846.
A01 A02
Inspection certificate 3.1+PED PN-EN 10204 1/1
A03
Document No 2020/10/16577 Z02 Date 2020-10-15
A04 A05
Manufacturer's mark Quality Assurance Department
A06.1 Customer Mick d.o.o
NIP: 865-00-13-543 kukuljanovo 447, 51227 kukuljanovo
Władysława Grabskiego 38 A06.2 Consignee Mick d.o.o
37-450 Stalowa Wola kukuljanovo 447, 51227 kukuljanovo
POLAND A06.3 Receiver of the document Mick d.o.o
PN-EN ISO 9001:2001 kukuljanovo 447, 51227 kukuljanovo
cert. Nr CSJ/115/2016 Purchaser's order Manufakturer's
A07 A08 2265
cert. Nr 01 202 PL/Q-13 0846 number works order num
B01 / B09 - B11 Product description B08 Quantity in psc
Cap - PN-EN 10253-2 TYP B - 139.7 x 4.0 30
B02 Steel and standard B07 Heat No
PN-EN 10253-2 TYP B ; Opc.9 ,AD 2000 W4 ; P265GH / EN 10028-2 ; 10601
B04 Delivery Condition/forming metod B12 Theoretical mass
Normalized 890/20 pow
B06 Marking KJ 139.7x4.0 PL F P265GH 10601 S DIN EN2 B
B14 Raw Material/Inspection certifikate of material
Plate according to the certificate 20/324276 01
B07 C71-C92 Chemical composition %
Heat No C Mn Si P S Cr Ni Cu Mo Al V Nb Ti N Sn B As CEV
10601 0.13 0.65 0.139 0.017 0.008 0.016 0.009 0.02 0.002 0.038 0.001 0.002 0.001 0.003 0.004 0 0.001 0.2441
Mechanical properties acc. ASME
C02 Direction of taking sample C33-C39 Diameter of the ball/weighting force
C00 C03 C11 C12 C13 C14 C30-C32
Test No Temp. °C Yield point Tensile strength Elongation Narrowing Hardness test on fitting
/MPa/ /MPa/ % Z% HBW
Result obtained
10601 22 ReH 319 428 A5 34.7
Impact test
C02 Direction of taking sample q - transverse C41 Size 2.5 x 10
C00 C03 C40 Mesaured value C44 value counted to standard measurements of
Test No Temp. °C Type of Unit C42 C42 C42 C43
specime 1 2 3 average Required 1 2 3 average
10601 -30 ISO-V J 24 26 24 24.7 96 104 96 98.7
D02-D99 Non-destructive and additional tests Standard Criterion
Z06 Suplementary confirmation
D01 Marking, surface and dimension checked - no objections. Z03 Work's Inspector stamp
Z01
Hereby we confirm that above-mentioned products became examined and realize requirements of given norms Z03 Work's Inspector
and order.
Z05 TASTA ARMATURA has a quality system in accordance with Directive 2014/68/EU Annex I section 4.3 -
Certificate CSJ/115/WM/PED/2016 and Certificate AD 2000-Merkblatt W0 No. 01 202 PL / Q-13 0846.
