The reliable brand

Ball Valves F14 / F14D

DIN Full Bore, Floa!ng Ball, 2-piece body

KITZ CORPORATION OF EUROPE S.A.

 Ball Valves
Floa!ng Ball design

Contents
Pressure - Temperature Rangs 3
Class PN 16 Cast Iron Ball Valves (F14) 4
Class PN 10 - 16 - 25 - 40 Carbon Steel Ball Valves (F14D) 6
Class PN 10 - 16 - 25 - 40 Stainless Steel Ball Valves (F14D) 8
Actuator Mounng Pad dimensions (F14D) 10
Applicable standards 11

KITZ Corporaon Headquarter, Chiba, Japan KITZ Corporaon of Europe, S.A., Barcelona Plant, Spain

All products introduced in this cataloge are covered by ISO 9001

certification awarded KITZ Corporation of Europe, S.A.

2
 Ball Valves, Floang Ball Design

Pressure-Temperature Rangs

The pressure-temperature rangs of ball valves are fluid service here, based on our past experiences both in the
determined, not only by valve shell materials, but more field and in our laboratory.
essenally by sealing materials, used for ball seats, gland
packing and gaskets. In case of extraordinary service condions as menoned
below, contact KITZ Corporaon of Europe or its distributors
Sealing materials may be high molecule, or rubber, but the for technical advice:
choice is limited by the characteriscs of the service fluid, 1. Valves shall be le fully closed for a long period of me
working temperatures, working pressures, velocity of fluid, under high temperature or high differenal pressure.
and operaonal frequency of valves.
2. Valves shall be frequently operated under high temperature
As it is very difficult to predetermine the exact pressure- or high differenal pressure.
temperature rang for all kind of fluids under all imaginable
condions, we have prepared general rang charts for non-shock 3. Frequent change of line pressure or temperature.

Virgin PTFE is the standard seat material for F14 and F14D series KITZ ball valves. Specify PTFE + Graphite or PTFE
+ Stainless Steel , PTFE + Glass Filled, etc. when required.

F14 PN10 - 16 DN 15 ~ 200

F14D PN10 - 16 - 25 - 40 DN 15 ~ 300 Body Rang: Pressure resistance limitaon for valve body

3
 Ball Valves, Floang Ball Design

F14 - Class PN16 Cast Iron Ball Valves

Full port, Split body, Side entry design
Features Leak test: BS EN 12266-1 Class A & DIN 3230
• An!sta!c device Lengths : Distance between flanges as per EN 558-1
• Blowout-proof stem DN ≤ 100 basic serie 14
• High performance PTFE ball seats DN ≥ 125 basic serie 15
• Standars: Design: EN ISO 17292 Thickness: ISO 7121 Page 3 for Pressure-Temperature Ra!ngs
Flanges drilled: EN 1092 Flanges surfaces: EN 1092 Page 5 for Construc!on and Materials

Features of PN16 F14 Un: mm

Cv Torque Weight
Valve Size
Port L X P H (m³/h) PN16 (Kg)
DN
(N.m)
15 12.5 115 52 150 85 17 5 1,8
20 19 120 55 150 90 39 6 2,8
25 25 125 58 150 104 63 8 3,7
32 32 130 58 200 115 104 15 6,1
40 38 140 60 200 120 150 20 7,5
50 51 150 60 250 132 254 25 10,9
65 65 170 75 250 144 381 40 15
80 76 180 78 250 154 971 60 20
100 102 190 95 500 212 1560 120 29,7
125 111 325 162 500 214 2173 150 46,5
150 144 350 175 750 238 4046 250 73
200 190 400 200 - Gear 146 (1)
opera!on 8787 500
1 Cv = 1,16 Kv

Valve Operator
Dn 15 ∼ 150 : lever opera!on
Dn 100 ∼ 150 : op!onal gear box
Gear Opera!on Un: mm Dn 200 : gear box or lever (op!onal)
(1) Gear box included
Gear Operator
Class PN16
H P1 B A
Worm gear operators may be mounted on KITZ
100 - 300 282 71 ball valves at your op!on for the smoothest valve
Valve Size 125 - 300 282 71 opera!on. Electric or pneuma!c actuators are also
(Dn) 150 - 300 282 71 op!onally available. Contact KITZ distributors for
200 303 400 340 86 appropriate choice and sizing of valve actuators.

4
 Ball Valves, Floang Ball Design

Construcon and Materials

Standard ¡ Standard material configuraon can be applied to

No. Parts sour service.
PN 16
1 Body GG25
*1 DN ≤ 50 : ASTM A479 Type 316
4 Body Connector GG25
:
DN > 50 ASTM A479 Type 410
5 An!sta!c Stem*1 ASTM A479 Type 316 / 410 *2 DN ≤ 32 : ASTM A479 Type 316
6 Gland Ring ASTM A479 Type 316 32 < DN ≤ 50 : DIN 1.4408
7 Gland Flange Steel DN > 50 : ASTM A217/A743 Gr. CA15
8 Stop Pin Steel DIN 1.4408 (Op!onal)
*3 DN ≤ 25 : PTFE+C+Graphite
9 Stop Plate Steel zinc plated :
DN > 25 PTFE
11 Gland Washer Blue Steel *4 DN ≤ 25 : PTFE
12 Nut*5 DIN 267/3-8 blued DN > 25 : 316L+ Flexite®
*5 DN < 40 : DIN 267/3 C8.8 blued
15 Elas!c Ring Steel
DN = 40 : DIN 267/3/4 C8.8/8 zinc plated
16 Gland bolt Steel :
DN > 40 DIN 267/3 C8.8 blued
17 Bolt - Stud Bolt*5 DIN 267/3/4 C8.8/8 blued / zinc plated
18 Nut*5 DIN 267/3/4 C8.8/8 blued / zinc plated
21 Ball*2 ASTM A479 Type 316 / 1.4408 / CA15 Valve finish : phosphate and oil dipped.
22 Ball Seat PTFE
Operaon group: DN ≤ 150 : by lever. (100 ~150 op!on: gear box)
24 Body Seal*4 PTFE / 316L+Flexite® DN = 200 : by gear box or with lever (Op!onal)
25 Gland Packing*3 PTFE+C+Graphite / PTFE
26 Stem Seal*3 PTFE+C+Graphite / PTFE
30 Handle Steel coated
31 Handle head GGG40
32 Handle bar GGG40
33 Handle bar bolt Stainless Steel
34 Handle head bolt Stainless Steel

DN ≤ 25

All part numbers are corresponding with those shown in valve assembly drawings.
5
 Ball Valves, Floang Ball Design

F14D - Class PN 10 - 16 - 25 - 40 Carbon Steel Ball Valves

Full port, Split body, Side entry design
Features Leak test: BS EN 12266-1 Class A & DIN 3230 FSM: BS 6755 P2
• An!sta!c device Lengths: Distance between flanges as per EN 558-1
• Blowout-proof stem DN ≤ 100 basic serie 14 (Short)
• High performance PTFE ball seats DN ≥ 125 basic serie 15 (Short) - Serie 1 (Long)
• Actuator moun!ng pad to ISO 5211 Page 3 for Pressure-Temperature Ra!ngs
• Standars: Design: EN 1983:2006 Thickness: EN 12516-1 Page 7 for Construc!on and Materials
Flanges drilled: EN 1092 Flanges surfaces: EN 1092 Page 10 for Dimension of Actuator Moun!ng Pad

Dimensions of PN 10 -16 - 25 - 40 F14D Un: mm

Weight
Torque (Kg)
Valve Size ISO Cv (N.m)
Port L X P H
DN 5211 (m³/h) PN10-16 PN25-40
Short Long PN16 PN40 Short Long Short Long
*1 PN 25-40:
15 14 115 130 50 150 85 F03 17 5 8 2,6 2,8 2,6 2,8
Ball Bore=95
20 19 120 150 52 150 90 F03 39 6 8 3,3 3,6 3,3 3,6
X= 85
25 25 125 160 55 150 104 F05 63 8 10 4,3 4,5 4,3 4,5
H=190
32 32 130 180 58 200 116 F05 104 15 20 6,5 6,7 6,5 6,7
*2 PN 25-40:
40 38 140 200 60 200 118 F05 150 20 25 7,8 7,9 7,8 7,9
P=750
50 51 150 230 60 250 128 F07 254 25 35 11,9 12,5 11,9 12,5
65 65 170 290 75 250 138 F07 381 40 50 15 16,1 15,5 16,5 *3 PN 25-40:
80 76 180 310 78 250 148 F07 971 60 90 20 22,5 21 23 H=396
100 (1) 102 190 350 95 500 196 F10 1560 120 175 33 39,6 34,5 40,2 *4 Gear Box
125 (2) 111 325 400 162.5 500 199 F10 2173 150 220 46 - 47 - included
150 144 350 480 175 750 223 F10 4046 250 350 73 80 75,5 85
200 190 400 - 200 - Gear F14 8787 500 750 175 (4) - 185 (4) -
opera!on
250 (3) 241 450 - 225 - Gear
opera!on F14 14452 1000 1400 230 (4) - 250 (4) -
300 285 500 - 250 - Gear F16 22893 1500 2000 305 (4) - 370 (4) -
opera!on
1 Cv = 1,16 Kv

Gear Opera!on Un: mm Valve Operator

Gear Operator Dn 15 ∼ 150 : lever opera!on
Class DN PN Dn 100 ∼ 150 : op!onal gear box
H P1 B A Dn 200 : gear box or lever (op!onal)
100 - 300 282 71
125 - 300 282 71 Worm gear operators may be mounted
16-40 on KITZ ball valves at your op!on
150 - 300 282 71
Valve Size for the smoothest valve opera!on.
200 342 400 340 86
(Dn) Electric or pneuma!c actuators are
10-16 378 400 340 86
250 also op!onally available. Contact
25-40 378 500 365 130 KITZ distributors for appropriate
300 10-40 440 500 365 130 choice and sizing of valve actuators.
6
 Ball Valves, Floang Ball Design

Construcon and Materials

Standard ¡ Standard material configuraon can be applied to

No. Parts sour service.
PN 10 - 16 - 25 - 40
1 Body DIN 1.0619
*1 DN ≤ 50 : ASTM A479 Type 316
4 Body Connector DIN 1.0619
50 < DN < 250 : ASTM A479 Type 410
5 Anstac Stem*1 ASTM A479 Type 316 / 410 ASTM A479 Type 316
DN ≥ 250 :
6 Gland Ring ASTM A479 Type 316 *2 DN ≤ 50 : ASTM A479 Type 316
8 Stop Pin Steel 50 < DN < 250 : ASTM A217/A743 Gr. CA15
9 Stop Plate Steel zinc plated DIN 1.4408 (Oponal)
DN ≥ 250 : DIN 1.4408
11 Gland Washer Steel zinc plated
*3 DN ≤ 25 : PTFE+C+Graphite
12 Nut DIN 267/3-8 blued DN > 25 : PTFE
17 Stud Bolt-Bolt DIN 267/3/4 C 8.8/8 / zinc plated Cod. FSM : Graphite (Oponal)
18 Nut DIN 267/3/4 C 8.8/8 / zinc plated *4 DN ≤ 25 : PTFE
DN > 25 : 316L+ Flexite®
21 Ball*2 ASTM A479 Type 316/CA15 / DIN 1.4408
Cod. FSM : 316L+Graphite (Oponal)
22 Ball Seat PTFE
*5 DN ≤ 25 PTFE+C+Graphite
:
24 Body Seal*4 PTFE / 316L+ Flexite® DN > 25 : PTFE
25 Gland Packing*3 PTFE+C+Graphite / PTFE
26 Stem Seal*5 PTFE+C+Graphite / PTFE
Valve finish : phosphate and oil dipped.
30 Handle Steel coated
31 Handle head GGG40 Operaon group : DN ≤ 150: by lever. (100 ~150 opon: gear box)
32 Handle bar GGG40 DN = 200: by gear box or with lever (Oponal)
33 Handle bar bolt Stainless Steel DN > 200: by gear box.

35 Bolt Steel
36 Washer Steel
40 Stem O’ring FKM

DN ≤ 25

All part numbers are corresponding with those shown in valve assembly drawings.
7
 Ball Valves, Floang Ball Design

F14D - Class PN 10 - 16 - 25 - 40 Stainless Steel Ball Valves

Full port, Split body, Side entry design
Features Leak test: BS EN 12266-1 Class A & DIN 3230 FSM: BS 6755 P2
• An!sta!c device Lengths: Distance between flanges as per EN 558-1
• Blowout-proof stem DN ≤ 100 basic serie 14 (Short)
• High performance PTFE ball seats DN ≥ 125 basic serie 15 (Short) - Serie 1 (Long)
• Actuator moun!ng pad to ISO 5211 Page 3 for Pressure-Temperature Ra!ngs
• Standars: Design: EN 1983:2006 Thickness: EN 12516-1 Page 9 for Construc!on and Materials
Flanges drilled: EN 1092 Flanges surfaces: EN 1092 Page 10 for Dimension of Actuator Moun!ng Pad

Dimensions of PN 10-16 - 25 - 40 F14D Un: mm

Weight
Torque (Kg)
Valve Size ISO Cv (N.m)
Port L X P H
DN 5211 (m³/h) PN10-16 PN25-40
Short Long PN16 PN40 Short Long Short Long
*1 PN 25-40:
15 14 115 130 50 150 85 F03 17 5 8 2,6 2,8 2,6 2,8
Ball Bore=95
20 19 120 150 52 150 90 F03 39 6 8 3,3 3,6 3,3 3,6
X= 85
25 25 125 160 55 150 104 F05 63 8 10 4,3 4,5 4,3 4,5
H=190
32 32 130 180 58 200 116 F05 104 15 20 6,5 6,7 6,5 6,7
*2 PN 25-40:
40 38 140 200 60 200 118 F05 150 20 25 7,8 7,9 7,8 7,9
P=750
50 51 150 230 60 250 128 F07 254 25 35 11,9 12,5 11,9 12,5
65 65 170 290 75 250 138 F07 381 40 50 15 16,1 15,5 16,5 *3 PN 25-40:
80 76 180 310 78 250 148 F07 971 60 90 20 22,5 21 23 H=396
100 (1) 102 190 350 95 500 196 F10 1560 120 175 33 39,6 34,5 41 *4 Gear Box
125 (2) 111 325 400 162.5 500 199 F10 2173 150 220 46 - 47 - included
150 144 350 480 175 750 223 F10 4046 250 350 73 80 75,5 85
200 190 400 - 200 - Gear F14 8787 500 750 175 (4) - 185 (4) -
opera!on
250 (3) 241 450 - 225 - Gear F14 14452 1000 1400 230 (4) - 250 (4) -
opera!on
300 285 500 - 250 - Gear F16 22893 1500 2000 305 (4) - 370 (4) -
opera!on
1 Cv = 1,16 Kv

Gear Opera!on Un: mm Valve Operator

Gear Operator Dn 15 ∼ 150 : lever opera!on
Class DN PN Dn 100 ∼ 150 : op!onal gear box
H P1 B A Dn 200 : gear box or lever (op!onal)
100 - 300 282 71
125 - 300 282 71 Worm gear operators may be mounted
16-40 on KITZ ball valves at your op!on
150 - 300 282 71
Valve Size for the smoothest valve opera!on.
200 342 400 340 86
(Dn) Electric or pneuma!c actuators are
10-16 378 400 340 86
250 also op!onally available. Contact
25-40 378 500 365 130 KITZ distributors for appropriate
300 10-40 440 500 365 130 choice and sizing of valve actuators.
8
 Ball Valves, Floang Ball Design

Construcon and Materials

Standard ¡ Standard material configuraon can be applied to

No. Parts sour service.
PN 10 - 16 - 25 - 40
1 Body DIN 1.4408
*1 DN ≤ 32 : ASTM A479 Type 316
4 Body Connector DIN 1.4408
DN > 32 : DIN 1.4408
5 Anstac Stem ASTM A479 Type 316 *2 DN ≤ 25 : PTFE+C+Graphite
6 Gland Ring ASTM A479 Type 316 DN > 25 : PTFE
8 Stop Pin DIN 267/11 A2-70 Cod. FSM : Graphite (Oponal)
*3 DN ≤ 25 : PTFE
9 Stop Plate Steel nickel plated
DN > 25 : 316L+ Flexite®
11 Gland Washer DIN 1.4122 (SS) Cod. FSM : 316L+Graphite (Oponal)
12 Nut DIN 267/11 A2-70 *4 DN ≤ 25 : PTFE+C+Graphite
17 Stud Bolt-Bolt*5 DIN 267/11/ A2-70 / 267/3 zinc plated DN > 25 : PTFE
*5 PN 10 - 16
18 Nut*5 DIN 267/11/ A2-70 / 267/3 zinc plated
DN ≤ 250 : DIN 267/11 A2-70
21 Ball*1 ASTM A479 Type 316 / 1.4408
DN > 250 : DIN 267/3 C8.8 zinc plated
22 Ball Seat PTFE PN 25 - 40
24 Body Seal*3 PTFE / 316L+Flexite® DN ≤ 150 : DIN 267/11 A2-70
25 Gland Packing*2 PTFE+C+Graphite / PTFE DN > 150 : DIN 267/3 C8.8 zinc plated
26 Stem Seal*4 PTFE+C+Graphite / PTFE
30 Handle SS+Plasc Valve finish : (SS) Natural.
31 Handle head GGG40
32 Handle bar GGG40 Operaon group: DN ≤ 150: by lever. (100 ~150 opon: gear box)
33 Handle bar bolt Stainless Steel DN = 200: by gear box or with lever (Oponal)
DN > 200: by gear box.
35 Bolt Stainless Steel
36 Washer Stainless Steel
40 Stem O’ring FKM

DN ≤ 25

All part numbers are corresponding with those shown in valve assembly drawings.
9
 Ball Valves, Floang Ball Design

F14D - ISO 5211 Top Dimensions

for Class PN 10 - 16 - 25 - 40 Full Port, Split Body, Side Entry Design Ball Valves

Dimensions Un: mm
F14D Nominal -0.05 -0.1 -0.1 M ISO 5211
± 0.2 L
Class size -0.10 -0.2 -0.2 B min. C F Flange
(Short)
(DN.) G øE øS øJ thread Type
15 6 25 - 36 9.5 18 115 M5 1.5 F03
20 6 25 - 36 8 16.5 120 M5 1.5 F03
PN 25 8 35 - 50 10 20.5 125 M6 2 F05
10-16 32 9 35 65 50 14.5 29 130 M6 2 F05
40 9 35 65 50 14.5 29 140 M6 2 F05
50 19 55 90 70 25.5 46 150 M8 3 F07
65 19 55 90 70 25.5 46 170 M8 3 F07
80 19 55 90 70 25.5 46 180 M8 3 F07
100 22 70 125 102 40.5 66 190 M10 3 F10
125 22 70 125 102 40.5 66 325 M10 3 F10
PN
150 22 70 125 102 40.5 66 350 M10 3 F10
25-40
200 30 GB 100 175 140 42 GB 64.5 GB
14 ACT 400 M16 3 F14
145.5 ACT 148.5 ACT
250 30 GB 100 175 140 42 GB 64.5 GB 450 M16 3 F14
14 ACT 145.5 ACT 148.5 ACT
300 18 130 210 165 171.5 174.50 500 M20 3 F16
DN 200/250/300: Dimensions with Gear Box (GB) or Actuator (ACT)

10
 Ball Valves, Floang Ball Design

Aplicable standards

Marking Coupling Flange

BS 5351 / MSS-SP-25 ISO 5211 / DIN 3337

Flanges
DIN 2501 / DIN 2526

Surface finish
MSS-SP-6 / DIN 2526

Set-up Design Standard

BS 5351 / DIN 3357

Quality Assurance
UNE-EN-ISO 9001
Face-to-Face distance
DIN 3202 F1 / F4 / F5
F1 : Long
F4 : ≤ DN100
F5 : ≥ DN125

Fire Safe Standard Tests Material Specificaon

BS 6755 P. 2 BS 6755 P.1 A / DIN 3230 P. 3 NACE MR 0175-2000

11
 EN-10-612-1

CAUTION
Pressure-temperature ratings and other performance data published in this catalog have been
developed from our design calculation, in-house testing, field reports provided by our customers
and/or published official standards or specifications. They are good only to cover typical applications
as a general guideline to users of KITZ products introduced in this catalog.

For any specific application, users are kindly requested to contact KITZ Corporation of Europe for
technical advice, or to carry out their own study and evaluation for proving suitability of these
products to such an application. Failure to follow this request could result in property damage and/
or personal injury, for which we shall not be liable.

While this catalog has been compiled with the utmost care, we assume no responsibility for errors,
impropriety or inadequacy. Any information provided in this catalog is subject to from time-to-time
change without notice for error rectification, product discontinuation, design modification, new
product introduction or any other cause that KITZ Corporation of Europe considers necessary. This
edition cancels all previous issues.

Kitz Corporation of Europe S.A.

Ramón Viñas, 8
08930 Sant Adrià de Besòs
Barcelona
Spain - España
Ph. +34 93 462 14 08
Fax. +34 93 462 03 49
[Link]