PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2016.4.15

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 1 OF 32

PRODUCT SPECIFICATION
FOR
APPROVAL
Model Name NV140FHM-N46
Description 14.0 FHD color TFT-LCD with LED backlight / Anti-Glare surface
Prepared by
Checked by
Approved by

Customer Dell

1
R2010-6053-O(3/3) A4(210 X 297)
 PROPRIETARY NOTE
THIS SPECIFICATION IS THE PROPERTY OF BOE BJ AND SHALL NOT BE
REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF BOE BJ AND
MUST BE RETURNED TO BOE BJ UPON ITS REQUEST

SPEC. NUMBER PRODUCT GROUP Rev. ISSUE DATE PAGE

TFT-LCD P1 2016.4.15 2 OF 32

NV140FHM-N46
Preliminary Product Specification Rev. P0
For Dell

BEIJING BOE DISPLAY TECHNOLOGY

R2010-6053-O(1/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2015.3.31

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 3 OF 32

REVISION HISTORY

REV. ECN No. DESCRIPTION OF CHANGES DATE PREPARED

P0 - Initial Release 2016.04.15

3
R2010-6053-O(2/3) A4(210 X 297)
 PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2016.4.15

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 4 OF 32

Contents
No. Items Page
1.0 General Description 5
2.0 Absolute Maximum ratings 7
3.0 Electrical specifications. 9
4.0 Optical specifications. 11
5.0 Interface Connection 16
6.0 Signal Timing Specification 18
7.0 Input Signals, Display Colors & Gray Scale of Colors 22
8.0 Power Sequence 22
9.0 Connector description 23
10.0 Mechanical Characteristics 24
11.0 Reliability Test 25

12.0 Handling & Cautions. 25

13.0 Label 26
14.0 Packing information 28
15.0 Mechanical Outline Dimension 29
16.0 EDID Table 31

4
R2010-6053-O(3/3) A4(210 X 297)
 PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2016.4.15

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 5 OF 32

1.0 GENERAL DESCRIPTION

1.1 Introduction

NV140FHM-N46 is a color active matrix TFT LCD module using amorphous silicon TFT's
(Thin Film Transistors) as an active switching devices. This module has a 14.0 inch
diagonally measured active area with FHD resolutions (1920 horizontal by 1080 vertical
pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in
vertical Stripe and this module can display 262,144 colors. The TFT-LCD panel used for this
module is a low reflection and higher color type. Therefore, this module is suitable for
Notebook PC. The LED Driver for back-light driving is built in this model.
All input signals are eDP interface compatible.

LED Driver

eDP Rx
eDP
Input +
Connector 1

T/CON
Signal
TFT LCD Panel

GOA
+ BACK LIGHT (Fluorescent Lamp)
PHI 1920 × 1080
VDD
DC/DC LED Lighting Bar
Gamma
Vcom Source Driver

1.2 Features

 2 lane eDP1.2 Interface with 2.7Gbps Link Rates

 Thin and light weight
 6-bit color depth, display 262K colors
 Single LED Lighting Bar. (Down side/Horizontal Direction)
 Data enable signal mode
 Side Mounting Frame
 Green Product (RoHS & Halogen free product)
 On board LED Driving circuit
 Low driving voltage and low power consumption
 On board EDID chip
5
R2010-6053-O(3/3) A4(210 X 297)
 PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2016.4.15

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 6 OF 32

1.3 Application

 Notebook PC (Wide type)

1.4 General Specification

The followings are general specifications at the model NV140FHM-N41 . (listed in Table 1.)

<Table 1. General Specifications>

Parameter Specification Unit Remarks

Active area 309.312(H) × 173.988(V) mm

Number of pixels 1920 (H) × 1080 (V) pixels

Pixel pitch 0.1611(H) × 0.1611 (V) mm

Pixel arrangement RGB Vertical stripe

Display colors 262K colors

Display mode Normally Black

Dimensional outline 320.4± 0.5 (H) × 205.1± 0.5 (V) × 3.0 max mm

Weight 290 (max) g

Surface treatment Anti-Glare / 3H

Back-light Down edge side, 1-LED Lighting Bar type Note 1

Power consumption PD : 0.9 (Typ.) W Note 2

PBL : 2.75 (max) W

Ptotal : 3.65 (Typ.) W

Notes : 1. LED Lighting Bar (36*LED Array)

Notes: 2. Typical Measurement Condition :Mosaic Pattern
6

R2010-6053-O(3/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2016.4.15

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 7 OF 32

2.0 ABSOLUTE MAXIMUM RATINGS

The followings are maximum values which, if exceed, may cause faulty operation or
damage to the unit. The operational and non-operational maximum voltage and current
values are listed in Table 2.

< Table 2. Absolute Maximum Ratings> Ta=25+/-2°C

Parameter Symbol Min. Max. Unit Remarks
Power Supply Voltage VDD -0.3 4.0 V
Note 1
Logic Supply Voltage VIN Vss-0.3 VDD+0.3 V
Operating Temperature TOP 0 +50 ℃
Note 2
Storage Temperature TST -20 +60 ℃

Notes : 1. Permanent damage to the device may occur if maximum values are exceeded
functional operation should be restricted to the condition described under normal
operating conditions.
2. Temperature and relative humidity range are shown in the figure below.
95 % RH Max. ( 40 OC ≥ Ta)
Maximum wet - bulb temperature at 39 OC or less. (Ta > 40 OC) No condensation.
Relative Humudity
100
(40, 95)
90

80 (50, 80)
Storage Range

60
Operating Range
Storage Range

40
(60, 27)

20

-40 -20 0 20 40 60 80
Temperature 7
(℃)

R2010-6053-O(3/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2016.4.15

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 8 OF 32

3.0 ELECTRICAL SPECIFICATIONS

3.1 Electrical Specifications

< Table 3. Electrical specifications > Ta=25+/-2°C

Parameter Min. Typ. Max. Unit Remarks

Power Supply Voltage VDD 3.0 3.3 3.6 V Note 1

Permissible Input Ripple

VRF - - 100 mV At VDD = 3.3V
Voltage

Power Supply Current IDD - TBD - mA Note 1

Positive-going Input
VIT+ - - 100 mV
Threshold Voltage
Vcm = 1.2V typ.
Negative-going Input
VIT- -100 - - mV
Threshold Voltage

Differential Input Voltage VID 200 - 600 mV

PD - - 1.45 W Note 1

Power Consumption PBL - - 2.75 W Note 2

Ptotal - - 4.2 W

Notes : 1. The supply voltage is measured and specified at the interface connector of LCM.
The current draw and power consumption specified is for 3.3V at 25℃.
Max : R/G/B Pattern
2. Calculated value for reference (VLED × ILED)

R2010-6053-O(3/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2016.4.15

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 9 OF 32

3.0 ELECTRICAL SPECIFICATIONS

3.2 Backlight Unit

< Table 4. LED Driving guideline specifications > Ta=25+/-2°C

Parameter Min. Typ. Max. Unit Remarks

LED Forward Voltage VF - - 3.0 V -

LED Forward Current IF - 21.5 mA -

LED Power Consumption PLED - 2.75 W Note 1

LED Life-Time N/A 15,000 - - Hour IF = 21.5mA
Power supply voltage for
VLED 5 12 21 V
LED Driver

Backlight on 2.2 5.0 V

EN Control
Level
Backlight off 0 0.6 V

PWM High
PWM 2.2 5.0 V
Level
Control
Level PWM Low
0 0.6 V
Level

PWM Control Frequency FPWM 200 - 10,000 Hz

Duty Ratio - 1 - 100 %

Notes : 1. Power supply voltage12V for LED Driver, Driver efficiency 87%,
Calculator Value for reference IF × VF × 36 / 0.87 = PLED
2. The LED Life-time define as the estimated time to 50% degradation of initial luminous.

9
R2010-6053-O(3/3) A4(210 X 297)
 PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2016.4.15

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 10 OF 32

3.3 LED structure

10
R2010-6053-O(3/3) A4(210 X 297)
 PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2016.4.15

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 11 OF 32

4.0 OPTICAL SPECIFICATION

4.1 Overview

The test of Optical specifications shall be measured in a dark room (ambient luminance  1
lux and temperature = 252℃) with the equipment of Luminance meter system (Goniometer
system and TOPCON BM-5) and test unit shall be located at an approximate distance
50cm from the LCD surface at a viewing angle of θ and Φ equal to 0. We refer to θØ=0
(=θ3 ) as the 3 o’clock direction (the “right”), θØ=90 (= θ12 ) as the 12 o’clock direction
(“upward”), θØ=180 (= θ9 ) as the 9 o’clock direction (“left”) and
θØ=270(= θ6 ) as the 6 o’clock direction (“bottom”). While scanning θand/or Ø, the center
of the measuring spot on the Display surface shall stay fixed. The backlight should be
operating for 30 minutes prior to measurement. VDD shall be 3.3+/- 0.3V at 25C.
Optimum viewing angle direction is 6 ’clock.
4.2 Optical Specifications
<Table 5. Optical Specifications>
Parameter Symbol Condition Min. Typ. Max. Unit Remark
Θ3 85 - Deg.
Horizontal
Viewing Angle Θ9 85 - Deg.
CR > 10 Note 1
range Θ12 85 - Deg.
Vertical
Θ6 85 - Deg.
Luminance Contrast ratio CR Θ = 0 600 800 Note 2
Luminance of
5 Points Yw 187 220 - cd/m2 Note 3
White
Θ = 0
White 5 Points ΔY5 80 - -
ILED = 20mA
Luminance Note 4
uniformity 13 Points ΔY13 65 - -
xw 0.283 0.313 0.343
White Chromaticity Θ = 0 Note 5
yw 0.299 0.329 0.359
xR 0.585
Red
yR 0.362
Reproduction xG 0.349
Green Θ = 0 -0.03 +0.03
of color yG 0.578
xB 0.163
Blue
yB 0.136
Response Time Ta= 25 C
TRT - 30 35 ms Note 6
(Rising + Falling) Θ = 0
Cross Talk CT Θ = 0 - - 2.0 % Note 7

11
R2010-6053-O(3/3) A4(210 X 297)
 PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2016.4.15

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 12 OF 32

Notes :
1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing
angles are determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12
o’clock direction with respect to the optical axis which is normal to the LCD surface (see
FIGURE 1).

2. Contrast measurements shall be made at viewing angle of Θ= 0 and at the center of

the LCD surface. Luminance shall be measured with all pixels in the view field set first to
white, then to the dark (black) state .
(see FIGURE 1) Luminance Contrast Ratio (CR) is defined mathematically.

Luminance when displaying a white raster

CR =
Luminance when displaying a black raster

3. Center Luminance of white is defined as luminance values of 5 point average across

the LCD surface. Luminance shall be measured with all pixels in the view field set first to
white. This measurement shall be taken at the locations shown in FIGURE 2 for a total of
the measurements per display.

4. The White luminance uniformity on LCD surface is then expressed as : ΔY =Minimum

Luminance of 5(or 13) points / Maximum Luminance of 5(or 13) points.
(see FIGURE 2 and FIGURE 3).

5. The color chromaticity coordinates specified in Table 5 shall be calculated from the
spectral data measured with all pixels first in red, green, blue and white. Measurements
shall be made at the center of the panel.

6. The electro-optical response time measurements shall be made as FIGURE 4 by

switching the “data” input signal ON and OFF. The times needed for the luminance to
change from 10% to 90% is Tr, and 90% to 10% is Td.

7. Cross-Talk of one area of the LCD surface by another shall be measured by comparing
the luminance (YA) of a 25mm diameter area, with all display pixels set to a gray level, to
the luminance (YB) of that same area when any adjacent area is driven dark.
(See FIGURE 5).

12
R2010-6053-O(3/3) A4(210 X 297)
 PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2016.4.15

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 13 OF 32
4.3 Optical measurements
Figure 1. Measurement Set Up

Photo detector
(TOPCON BM-5A)

o
Field = 2
50 cm
TFT-LCD module LCD panel

Center of the screen

Optical characteristics measurement setup

Figure 2. White Luminance and Uniformity Measurement Locations (5 points)

Center Luminance of white is defined as luminance values of center 5 points

across the LCD surface. Luminance shall be measured with all pixels in the view
field set first to white. This measurement shall be taken at the locations shown in
FIGURE 2 for a total of the measurements per display.
13
R2010-6053-O(3/3) A4(210 X 297)
 PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2016.4.15

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 14 OF 32

Figure 3. Uniformity Measurement Locations (13 points)

The White luminance uniformity on LCD surface is then expressed as : ΔY5 =

Minimum Luminance of five points / Maximum Luminance of five points (see
FIGURE 2) , ΔY13 = Minimum Luminance of 13 points /Maximum Luminance of
13 points (see FIGURE 3).

Figure 4. Response Time Testing

Display data White(TFT OFF) Black(TFT ON) White(TFT OFF)

TR TF
100%
Optical
90%
Response

10%
0%
Time

The electro-optical response time measurements shall be made as shown in

FIGURE 4 by switching the “data” input signal ON and OFF. The times needed
for the luminance to change from 10% to 90% is Td and 90% to 10% is Tr.

14
R2010-6053-O(3/3) A4(210 X 297)
 PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2016.4.15

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 15 OF 32

Figure 5. Cross Modulation Test Description

VIEW AREA VIEW AREA

342,192 1025, 192

L31 YB(1195, 384)

342,576 1025,576

YA (1195, 384) L0

YB - YA
Cross-Talk (%) = × 100
YA

Where:
YA = Initial luminance of measured area (cd/m2)
YB = Subsequent luminance of measured area (cd/m 2)
The location measured will be exactly the same in both patterns

Cross-Talk of one area of the LCD surface by another shall be measured by

comparing the luminance (YA) of a 25mm diameter area, with all display pixels
set to a gray level, to the luminance (YB) of that same area when any adjacent
area is driven dark (Refer to FIGURE 5).

15
R2010-6053-O(3/3) A4(210 X 297)
 PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2016.4.15

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 16 OF 32
5.0 INTERFACE CONNECTION.
5.1 Electrical Interface Connection
The electronics interface connector is UJU IS050-L30B-C10
The connector interface pin assignments are listed in Table 6.

<Table 6. Pin Assignments for the Interface Connector>

Terminal Symbol Functions
Pin No. Symbol Description
1 CABC_ENABLE CABC_ENABLE
2 H_GND Ground
3 LANE1_N eDP RX channel 1 negative
4 LANE1_P eDP RX channel 1 positive
5 H_GND Ground
6 LANE0_N eDP RX channel 0 negative
7 LANE0_P eDP RX channel 0 positive
8 H_GND Ground
9 AUX_CH_P eDP AUX CH positive
10 AUX_CH_N eDP AUX CH negative
11 H_GND Ground
12 LCD_VCC Power Supply, 3.3V (typ.)
13 LCD_VCC Power Supply, 3.3V (typ.)
14 Bist Panel self test enable
15 H_GND Ground
16 H_GND Ground
17 HPD Hot plug detect output
18 BL_GND LED Ground
19 BL_GND LED Ground
20 BL_GND LED Ground
21 BL_GND LED Ground
22 BL_ENABLE LED enable pin(+3.3V Input)
23 BL_PWM System PWM Signal Input
24 HSYNC 预留HSYNC功能
25 NC No Connection
26 BL_POWER LED Power Supply 5V-21V
27 BL_POWER LED Power Supply 5V-21V
28 BL_POWER LED Power Supply 5V-21V
29 BL_POWER LED Power Supply 5V-21V
30 NC NC
16
R2010-6053-O(3/3) A4(210 X 297)
 PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2016.4.15

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 17 OF 32
5.2. eDP Interface

PC Side TFT-LCD Side

eDP interface

6
eDP Source Function R0~R5

eDP to mLVDS Parallel

6
Video / Main link G0~G5
6
Graphics B0~B5

Processing AUX chanel

Hsync

Circuits Vsync

DE
HPD

CLK

Note. Transmitter : Parade NV71832 or equivalent.

Transmitter is not contained in Module.

[Link] Input signal

Lane 0
R0-5:0 G0-5:4
G0-3.0 B0-5:2
B0-1:0 R1-5:0
G1-5:0 B1-5:4
B1-3:0 R2-5:2
R2-1:0 G2-5:0
B2-5:0 R3-5:4
R3-3:0 G3-5:2
G3-1:0 B3-5:0

17
R2010-6053-O(3/3) A4(210 X 297)
 PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2016.4.15

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 18 OF 32

5.4 Back-light & LCM Interface Connection

Interface Connector: MSK24022P10

<Table 7. Pin Assignments for the BLU & LCM Connector>

Pin No. Symbol Description Pin No. Symbol Description

1 LED1 LED cathode connection 6 Ground Ground
2 LED2 LED cathode connection 7 NC No Connection
3 LED3 LED cathode connection 8 Vout LED anode connection
4 LED4 LED cathode connection 9 Vout LED anode connection
5 NC No Connection 10 Vout LED anode connection

18

R2010-6053-O(3/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2016.4.15

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 19 OF 32

6.0 SIGNAL TIMING SPECIFICATION

6.1 The NV140FHM-N46 is operated by the DE only.

Item Symbols Min Typ Max Unit

Clock Frequency 1/Tc 100 147.8 160 MHz

1112 1125 1238 lines
Frame Period Tv 40 60 66 Hz
25 16.67 15.15 ms
Vertical Display Period Tvd - 1080 - lines
One line Scanning
Th 2080 2200 2400 clocks
Period
Horizontal Display
Thd - 1920 - clocks
Period

19
R2010-6053-O(3/3) A4(210 X 297)
 PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2016.4.15

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 20 OF 32

6.2 eDP Rx Interface Timing Parameter

The specification of the eDP Rx interface timing parameter is shown in Table 8.

<Table 8. eDP Rx Interface Timing Specification>

Item Symbol Min Typ Max Unit Remark
Spread spectrum clock ssc 0.5 %

Differential peak-to-peak input volt

VRX-DIFFp-p 100 0 1320 mV
age at package pins

Rx input DC common mode

VRX_DC_CM - GND - V
voltage
Differential termination
RRX-DIFF 80 - 100 Ω
resistance
Single-ended termination
RRX-SE 40 - 60 Ω
resistance

Rx short circuit current limit IRX_SHORT - - 20 mA

Intra-pair skew at Rx package pins

(HBR) LRX_SKEW_ - - 150 ps
RX intra-pair skew tolerance at INTRA_PAIR
HBR

100%

VRX_DIFFp-p

0%

VD+

VRX_DC_CM 50%

VD-
LRX_SKEW_INTRA_PAIR

20

R2010-6053-O(3/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2016.4.15

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 21 OF 32

7.0 INPUT SIGNALS, BASIC DISPLAY COLORS & GRAY SCALE OF COLORS

Colors & Data signal

Gray scale R0 R1 R2 R3 R4 R5 G0 G1 G2 G3 G4 G5 B0 B1 B2 B3 B4 B5
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Blue 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1
Basic Green 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0
colors Light Blue 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1
Red 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0
Purple 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1
Yellow 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0
White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
△ 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Darker 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Gray scale △ ↑ ↑ ↑
of Red ▽ ↓ ↓ ↓
Brighter 1 0 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0
▽ 0 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0
Red 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
△ 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0
Darker 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0
Gray scale △ ↑ ↑ ↑
of Green ▽ ↓ ↓ ↓
Brighter 0 0 0 0 0 0 1 0 1 1 1 1 0 0 0 0 0 0
▽ 0 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0
Green 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
△ 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
Darker 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0
Gray scale △ ↑ ↓ ↑
of Blue ▽ ↓ ↓ ↓
Brighter 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 1 1
▽ 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1
Blue 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Gray △
△ 1 0 0 0 0 0 1 0 0 0 0 0 1 0 0 0 0 0
scale Darker 0 1 0 0 0 0 0 1 0 0 0 0 0 1 0 0 0 0
of ↑ ↑ ↑
White ▽ ↓ ↓ ↓
& Brighter 1 0 1 1 1 1 1 0 1 1 1 1 1 0 1 1 1 1
Black ▽ 0 1 1 1 1 1 0 1 1 1 1 1 0 1 1 1 1 1
White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

21
R2010-6053-O(3/3) A4(210 X 297)
 PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2016.4.15

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 22 OF 32

8.0 POWER SEQUENCE

To prevent a latch-up or DC operation of the LCD module, the power on/off seq
uence shall be as shown in below
Power supply for logic Vdd 90% 90%
10% 10% 10%

T1 T2 T10 T11 T12

eDP Display Black Video Video form Source Black Video

HPD from Sink T3

Sink Aux CH AUX Channel Operational

T4 T7
Source Main-Link Link
Training
Idle Valid video data
Or PSR active
Idle or off
data
T5 T6 T8 T9
LED_EN

PWM
90% 90%
Power supply for BL 10% T13 T16 10%
(VBL )
T17 T14 T15 T18
● 0.5ms  T1  10 ms ● 0ms  T7  50ms
● 0ms  T2  200 ms ● 0ms  T10  500 ms
● 0ms  T3  200 ms ● T11  10 ms
● 10ms  T13 ● 500ms  T12
● 20ms  T14 ● 20ms  T15
● 0.5ms  T17  20ms ● 10ms  T16
Notes: ● 0.5ms  T18  20ms
1. When the power supply VDD is 0V, keep the level of input signals on
the low or keep high impedance.
2. Do not keep the interface signal high impedance when signal invalid period.
3. Backlight power must be turn on after power for logic and interface signal
is valid.
R2010-6053-O(3/3) A4(210 X 297)
 PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2016.4.15

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 23 OF 32

9.0 Connector Description

Physical interface is described as for the connector on LCM.
These connectors are capable of accommodating the following signals and will
be following components.

9.1 TFT LCD Module

Connector Name /Description For Signal Connector

Manufacturer UJU

Type/ Part Number IS050-L30B-C10

Mating housing/ Part Number I-PEX 20454-030T or Compatible

23
R2010-6053-O(3/3) A4(210 X 297)
 PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2016.4.15

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 24 OF 32

10.0 MECHANICAL CHARACTERISTICS

10.1 Dimensional Requirements

FIGURE 6 shows mechanical outlines for the model NV140FHM-N41.

Other parameters are shown in Table 9.

<Table 9. Dimensional Parameters>

Parameter Specification Unit

Active Area 309.312 (H) × 173.988 (V)
Number of pixels 1920 (H) X 1080 (V) (1 pixel = R + G + B dots)
Pixel pitch 0.1611 (H) X 0.1611 (V)
Pixel arrangement RGB Vertical stripe
Display colors 262K
Display mode Normally Black
Dimensional outline 320.4± 0.5*198.6± 0.5*3.0max mm
Weight 290 (max) gram
Connector : MSK24022P10
Back Light
LED, Horizontal-LED Array type

10.2 Mounting

See FIGURE 6.

10.3 Anti-Glare and Polarizer Hardness.

The surface of the LCD has an AG coating to minimize reflection and a coating to reduce
scratching.

10.4 Light Leakage

There shall not be visible light from the back-lighting system around the edges of the
screen as seen from a distance 50cm from the screen with an overhead light level of 350lux.

24
R2010-6053-O(3/3) A4(210 X 297)
 PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2016.4.15

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 25 OF 32
11.0 RELIABILITY TEST
The Reliability test items and its conditions are shown in below.
<Table 10. Reliability test>
No Test Items Conditions
1 High temperature storage test Ta = 60 ℃, 240 hrs
2 Low temperature storage test Ta = -20 ℃, 240 hrs
High temperature & high humidity
3 Ta = 50 ℃, 80%RH, 240 hrs
operation test
4 High temperature operation test Ta = 50 ℃, 240 hrs
5 Low temperature operation test Ta = 0 ℃, 240 hrs
6 Thermal shock Ta = -20 ℃ ↔ 60 ℃ (0.5 hr), 100 cycle
Vibration test 1.5G, 10~500Hz,Half Sine
7
(non-operating) X,Y,Z / Sweep rate : 1 hour
Shock test 220G, Half Sine Wave 2msec
8
(non-operating) ± X,± Y,± Z Once for each direction
Electro-static discharge test Air : 150 pF, 330Ω, 15 KV
9
(non-operating) Contact : 150 pF, 330Ω, 8 KV

12.0 HANDLING & CAUTIONS

(1) Cautions when taking out the module

 Pick the pouch only, when taking out module from a shipping package.
(2) Cautions for handling the module
 As the electrostatic discharges may break the LCD module, handle the LCD module with
care. Peel a protection sheet off from the LCD panel surface as slowly as possible.
 As the LCD panel and back - light element are made from fragile glass material, impulse
and pressure to the LCD module should be avoided.
 As the surface of the polarizer is very soft and easily scratched, use a soft dry cloth
without chemicals for cleaning.
 Do not pull the interface connector in or out while the LCD module is operating.
 Put the module display side down on a flat horizontal plane.
 Handle connectors and cables with care.
(3) Cautions for the operation
 When the module is operating, do not lose CLK, ENAB signals. If any one of these
signals is lost, the LCD panel would be damaged.
 Obey the supply voltage sequence. If wrong sequence is applied, the module
would be damaged.
25
R2010-6053-O(3/3) A4(210 X 297)
 PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2016.4.15

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 26 OF 32

(4) Cautions for the atmosphere

 Dew drop atmosphere should be avoided.
 Do not store and/or operate the LCD module in a high temperature and/or humidity
atmosphere. Storage in an electro-conductive polymer packing pouch and under relatively
low temperature atmosphere is recommended.

(5) Cautions for the module characteristics

 Do not apply fixed pattern data signal to the LCD module at product aging.
 Applying fixed pattern for a long time may cause image sticking.

(6) Other cautions

 Do not disassemble and/or re-assemble LCD module.
 Do not re-adjust variable resistor or switch etc.
 When returning the module for repair or etc., Please pack the module not to be broken.
We recommend to use the original shipping packages.
13.0 LABEL
(1) Product label

1 2 3 4 5 6 7

X X X X X X 1 0 0 X X X X X X X X

Type designation No 5. Month (1, 2, 3, …, 9, X, Y, Z)

No 1. Control Number No 6. Product Identification (FG)
No 2. Rank / Grade No 7. Serial Number
No 3. Line classification
No 4. Year (10 : 2010, 11: 2011, …) 26
R2010-6053-O(3/3) A4(210 X 297)
 PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2016.4.15

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 27 OF 32

(2) High voltage caution label

(3) Box label

Label Size: 110 mm (L)  56 mm (W)

Contents
Model: NV140FHM-N41
Q`ty: Module Q`ty in one box
Serial No.: Box Serial No. See next figure for detail description.
Date: Packing Date
Internal use of Product

SERIA NO 1 2 3 4 5 6 7 8 9 10 11 12 13

code X X X X X X X X X X X X X

Description GBN Grade Line Year Month Rev Serial No.

27
R2010-6053-O(3/3) A4(210 X 297)
 PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2016.4.15

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 28 OF 32

14.0 PACKING INFORMATION

14.1 Packing order

-. Put Pad into the inner box
-. Insert EPE block into the Gap between Pad and box
Built-in Pad
EPE Buffer

EPE Pad+PE Bag

step 2
step 1

-. Put Cover on the top of the pad

Cover

step 4
-. 12ea Box/Pallet, 456ea MDL/Pallet

14.2 Notes step 3

 Box Dimension: 580mm(W) x 450mm(D) x 280mm(H)
 Package Quantity in one Box: 38pcs
 Total Weight: 15kg
28
R2010-6053-O(3/3) A4(210 X 297)
 PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2016.4.15

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 29 OF 32

15.0 MECHANICAL OUTLINE DIMENSION

Figure 6. TFT-LCD Module Outline Dimension (Front View)

29
R2010-6053-O(3/3) A4(210 X 297)
 PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2016.4.15

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 30 OF 32

Figure 7. TFT-LCD Module Outline Dimensions (Rear view)

30
R2010-6053-O(3/3) A4(210 X 297)
 PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2016.4.15

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 31 OF 32
16.0 EDID Table
Address
Function Hex Dec crc Input values. Notes
(HEX)
00 00 0 0
01 FF 255 255
02 FF 255 255
03 FF 255 255
Header EDID Header
04 FF 255 255
05 FF 255 255
06 FF 255 255
07 00 0 0
08 09 9
ID Manufacturer Name BOE ID = BOE
09 E5 229
0A E2 226
ID Product Code 1762 ID = 1762
0B 06 6
0C 00 0
0D 00 0
32-bit serial No.
0E 00 0
0F 00 0
10 Week of manufacture 1 1 1
11 Year of Manufacture 1A 26 2016 Manufactured in 2016
12 EDID Structure Ver. 01 1 1 EDID Ver 1.0
13 EDID revision # 04 4 4 EDID Rev. 0.4
14 Video input definition 95 149 -
15 Max H image size 1F 31 31 31 cm (Approx)
16 Max V image size 11 17 17 17 cm (Approx)
17 Display Gamma 78 120 2.2 Gamma curve = 2.2
18 Feature support 0A 10 RGB display, Preferred Timming mode
19 Red/Green low bits E7 231 - Red / Green Low Bits
1A Blue/White low bits B0 176 - Blue / White Low Bits
1B Red x high bits 95 149 599 0.585 Red (x) = 10010101 (0.585)
1C Red y high bits 5C 92 370 0.362 Red (y) = 01011100 (0.362)
1D Green x high bits 59 89 357 0.349 Green (x) = 01011001 (0.349)
1E Green y high bits 94 148 591 0.578 Green (y) = 10010100 (0.578)
1F Blue x high bits 29 41 166 0.163 Blue (x) = 00101001 (0.163)
20 BLue y high bits 22 34 139 0.136 Blue (y) = 00100010 (0.136)
21 White x high bits 50 80 320 0.313 White (x) = 01010000 (0.313)
22 White y high bits 54 84 336 0.329 White (y) = 01010100 (0.329)

31
R2010-6053-O(3/3) A4(210 X 297)
 PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2016.4.15

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 32 OF 32

Address
Function Hex Dec crc Input values. Notes
(HEX)
23 Established timing 1 00 0 -
24 Established timing 2 00 0 -
25 Established timing 3 00 0 -
26 01 1
Standard timing #1 Not Used
27 01 1
28 01 1
Standard timing #2 Not Used
29 01 1
2A 01 1
Standard timing #3 Not Used
2B 01 1
2C 01 1
Standard timing #4 Not Used
2D 01 1
2E 01 1
Standard timing #5 Not Used
2F 01 1
30 01 1
Standard timing #6 Not Used
31 01 1
32 01 1
Standard timing #7 Not Used
33 01 1
34 01 1
Standard timing #8 Not Used
35 01 1
36 3C 60
141.40 141.4MHz Main clock
37 37 55
38 80 128 1920 Hor Active = 1920
39 DE 222 222 Hor Blanking = 222
4 bits of Hor. Active + 4 bits of Hor.
3A 70 112 -
Blanking
3B 38 56 1080 Ver Active = 1080
3C 14 20 20 Ver Blanking = 20
4 bits of Ver. Active + 4 bits of Ver.
3D 40 64 -
Blanking
3E Detailed timing/monit 30 48 48 Hor Sync Offset = 48
3F or 20 32 32 H Sync Pulse Width = 32
40 descriptor #1 36 54 3 V sync Offset = 3 line
41 00 0 6 V Sync Pulse width : 6 line
Horizontal Image Size = 309 mm (Low 8
42 35 53 309
bits)
43 AD 173 173 Vertical Image Size = 173 mm (Low 8 bits)
4 bits of Hor Image Size + 4 bits of Ver
44 10 16 -
Image Size
45 00 0 0 Hor Border (pixels)
46 00 0 0 Vertical Border (Lines)
47 1A 26 Refer to right table
32
R2010-6053-O(3/3) A4(210 X 297)
 PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2016.4.15

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 33 OF 32

Address
Function Hex Dec crc Input values. Notes
(HEX)
48 30 48
113.12 113.12MHz Main clock
49 2C 44
4A 80 128 1920 Hor Active = 1920
4B DE 222 222 Hor Blanking = 222
4 bits of Hor. Active + 4 bits of Hor.
4C 70 112 -
Blanking
4D 38 56 1080 Ver Active = 1080
4E 14 20 20 Ver Blanking = 20
4 bits of Ver. Active + 4 bits of Ver.
4F 40 64 -
Blanking
50 Detailed timing/monit 30 48 48 Hor Sync Offset = 48
51 or 20 32 32 H Sync Pulse Width = 32
52 descriptor #2 36 54 3 V sync Offset = 3 line
53 00 0 6 V Sync Pulse width : 6 line
Horizontal Image Size = 380 mm (Low 8
54 7C 124 380
bits)
Vertical Image Size = 210 mm (Low 8
55 D2 210 210
bits)
4 bits of Hor Image Size + 4 bits of Ver
56 10 16 -
Image Size
57 00 0 0 Hor Border (pixels)
58 00 0 0 Vertical Border (Lines)
59 1A 26
5A 00 0
5B 00 0
5C 00 0 ASCII Data Sting Tag
5D FE 254
5E 00 0
5F 43 67 C
60 4A 74 J
61 35 53 5 D/PN:CJ5JM
Detailed timing/monit
62 4A 74 J
or
63
descriptor #3 4D 77 M
64 14 20 00010100 EDID:X20
65 4E 78 N
66 56 86 V
67 31 49 1
68 34 52 4 BOE PN
69 4E 78 N
6A 34 52 4
6B 36 54 6

33
R2010-6053-O(3/3) A4(210 X 297)
 PRODUCT GROUP REV ISSUE DATE

TFT- LCD PRODUCT P0 2016.4.15

SPEC. NUMBER SPEC. TITLE PAGE

NV140FHM-N46 Preliminary Product Specification 34 OF 32

Address
Function Hex Dec crc Input values. Notes
(HEX)
6C 00 0
6D 00 0
6E 00 0 Product Name Tag (ASCII)
6F 00 0
70 00 0
71 00 0 00000000 6-bit Color Depth & NO FRC
72 41 65 01000001 WLED & singal light bar & one light bar
73 11 17 00010001 Frame rate 40Hz~65Hz
Light Controller:PWM & Max. Luminance
74 Detailed timing/monit 96 150 10010110
220
or
75 descriptor #4 00 0 00000000 Front Surface:Anti-Glare& RGB v-stripe
76 00 0 00010000 with DBC
77 00 0 00000000 no Motion Blur & no Active Gamma
no Wireless Enhancement & no In-Cell
78 00 0 00000000
Scanner
79 0A 10 00001010 2 Lane edp1.2
7A 01 1 00000001 Built-In Self Test
7B 0A 10
7C 20 32
7D 20 32
7E Extension flag 00 0
7F Checksum 45 69 69 -

34
R2010-6053-O(3/3) A4(210 X 297)