HYDM140
Introduction
Clean-Cuts hydraulic hose cutting system is break-through technology using a toothed blade, cutting with the backs of
each tooth, so the blade does not take a kerf. The saw bends the hose into the blade spreading the cut edges to avoid
burning and smoking.
How It Works
1/8” Abrasive
Old Method
Wheel The normal sawing method of lowering an abrasive saw blade onto the
Hydraulic Hose hose causes the hose to compress and deform. As the blade cuts the
compressed hose expands against the blade causing friction, heating and
burning and much of the debris from the kerf of the blade is deposited
into your hose.
Hydraulic Hos Hydraulic Hose
DEBRIS INSIDE
YOUR HOSE!
B D
E
New Improved Clean-Cuts Method
A
With the Clean-Cuts hydraulic hose saws the hose is positioned across
two pins (A) and moved into the blade (C) by a feed foot (B) using extend-
able handle (D) and adjustable pivot point (E) for cutting larger industrial
hose. The feed motion causes the hose to stretch at the point of contact
with the blade, allowing it to separate as it is cut (see image at below). This
separation allows the hose to pass clear of the saw blade with NO friction,
NO heating and NO DEBRIS! A vacuum hose (not shown) is attached to a
vacuum port to remove any tiny amount of debris or smoke during cutting.
C
1/8” Clean-Cuts Blade
Hose separates
as blade slices,
Pin A no kerf required.
Pin A
ose ||||||||||| Hydra
ulic
H
raulic Hos
e ||
H yd |||||
NO DEBRIS
Benefits
• Cleaner Cuts
• Safer Cuts
• No Smoke
MODEL MOTOR BLADE CUTTING CAPACITY
HYDM140-220V 5 HP, 220 VAC, 1 Phase, one 14” OD x .160 THK X 2″ ID x 6 Wire Hydraulic Hose
60 Cycle, 3,490 RPM 40 mm arbor — 5″ OD Industrial Hose
HYDM140-220V3 3 HP, 220 VAC, 3 Phase, one 14” OD x .160 THK X 2″ ID x 6 Wire Hydraulic Hose
60 Cycle, 3,490 RPM 40 mm arbor — 5″ OD Industrial Hose
HYDM140-440V3 3 HP, 440 VAC, 3 Phase, one 14” OD x .160 THK X 2″ ID x 6 Wire Hydraulic Hose
60 Cycle, 3,490 RPM 40 mm arbor — 5″ OD Industrial Hose
Hose Cutting Blades
The following 5 types of blades are designed to cut hydraulic
hose. If you’re not sure which is best suited to your applica-
tion please call for our recommendation.
Clean-Cuts blades are manufactured in: M-2, D-2, M-35, &
High Speed Steels.
Smooth Blade
ROTATION ROTATION
Advanced Scallop Blade Diamond Blade
ROTATION
Micro-Slotted Blade Slotted Blade
MODEL TYPE BLADE SIZE CUTTING CAPACITY
HYD14X160X40 Advanced Scallop Blade 14” OD x .160 THK 2″ ID x 4 Wire Hydraulic Hose —
X 40 mm arbor 5″ OD Industrial Hose
MSE14X160X40 Micro-Slotted Blade 14” OD x .160 THK 2″ ID x 4 Wire Hydraulic Hose —
X 40 mm arbor 5″ OD Industrial Hose
HYD14X160X40DS Diamond Blade 14” OD x .160 THK 2″ ID x 6 Wire Hydraulic Hose —
X 40 mm arbor 5″ OD Industrial Hose
CDBK14X160X40 Smooth Blade 14” OD x .160 THK 2″ ID x 4 Wire Hydraulic Hose —
X 40 mm arbor 5″ OD Industrial Hose
SSE14X160X40 Slotted Blade 14” OD x .160 THK 2″ ID x 4 Wire Hydraulic Hose —
X 40 mm arbor 5″ OD Industrial Hose
Specialty Saw, Inc.
30 Wolcott Road
Simsbury, CT 06070 USA
1-800-225-0772
Voice: (860) 658-4419 ~ Fax: (860) 651-5358
Email: [email protected]
Website: http://specialtysaw.com
© Specialty Saw, Inc. 2015
