‘TECHNICAL REPORT CEN/TR 17052 RAPPORT TECHNIQUE TECHNISCHER BERICHT January 2017 Ics 91,080.10 English Version Guidelines on implementing EN 1090-1:2009+A1:2011, Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components Lignes directrices pour application de TEN 1090- Lelfaden far die Umsetzung von EN 1090- 1:2009+A1:2011, Exécution des structures en acier et 4:2009+A1:2011, Ausfbhrung von Stahibetonwerken des structures en aluminium - Partie 1: Exigences pour und Alurniniumtragwerken - Tell 1 rg Vévaluation de la conformité des éléments structuraux Konformitatsnachwelsverfahren fur tragende Bautelle = ule belongs to the Estonian Centre for Standardisation ‘This Technical Report was approved by CEN on 11 December 2016, Ithas been drawn up by the Technical Committee CEN/TC 135, CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Caech Republic, Denmark, Eston, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romana, Serbia, Slovakia, Slovenia Span, Sweden, Switzerland, ‘Turkey and United Kingdom. ‘ence. Order No. 214329, 5/221 Right of Use of this electronic document: Enrico COSTA, the right to reproduce and dist Single-user aa [EUROPEAN COMMITTEE FOR STANDARDIZATION COMITS EUROPEEN DE NORMALISATION EUROPAISCHES KOMITEE FOR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels © 2017 CEN Allrightsof exploitation in any form and by any means reserved Ref-No, CEN/TR 17052:2017 ‘worldwide for CEN national Members.CEN/TR 17052:2017 (E) Contents Page European foreword. Introduction DL SCOPE ann 2 Normative reference: 3 Termsand definitions.. soe 4 Conditions necessary for construction products to be covered by the scope of EN 1090-1... 5 Clarification. 5.1 General ——— ——— 5.2 Condition 1 - The product fulfils the requirements of EN 1090-2 or EN 1090-3 5.3. Condition 2 - The product isa structural construction product within the meaning of the Construction Products Regulation (EU) 305/2011.. 5.3.1 Condition 2a - The product is intended to be incorporated construction works. = 5.3.2 Condition 2b - The product has a structural function in relation to the construction work. = = 5.4 Condition 3 - The product is not covered by another European technical specification. 5.4.1 General 5.4.2 Construction products covered by another harmonized standard ... 5.4.3 Construction products covered by an ETA... ‘Annex A (informative) Products covered by EN 1090-1 Annex B (informative) Products not covered by EN 1090-: Single-user licence, Order No, 214329, 5/22/2017. Right of Use of this electronic document: Enrico COSTA, the right io reproduce and distribute belongs to the Estonian Centre for Standardisation,CEN/TR 17052:2017 (E) European foreword This document (CEN/TR17052:2017) has been prepared by Technical Committee CEN/TC 135 “Execution of steel structures and aluminium structures”, the secretariat of which is held by SN. ‘Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. ‘This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association. belongs to the Estonian Centre for Standardisation le-user licence. Order No. 214329, 5/22/2017. STA, the Sing Right of Use of this electronic document: Enrico CiCEN/TR 17052:2017 (E) Introduction ‘The scope of the standard EN 1090-1:2009+A1:2011 “Execution of steel structures and aluminium structures: Part 1: Requirements for conformity assessment of structural components” is very broad and prompted the European Commission to publish on their website under the category “Frequently Asked Questions (FAQ) on the Constructions Products Regulation” a set of conditions for identifying when a steel or aluminium product falls within its scope and an indicative, non-exhaustive list of products that are not covered by the scope of EN 1090-1:2009+A1:2011. Thi websi document aims to clarify in addition to the answers given on the European Commission's FAQ the scope of EN 1090-1:2009#A1:2011. ibute belongs to the Estonian Centre for Standardisation, jcence, Order No. 214329, 5/22/2017. Right of Use of this electronic document: Enrico COSTA, the right fo reproduce and di SinCEN/TR 17052:2017 (E) 1 Scope ‘The scope of EN 1090-1:2009+A1:2011 states that the standard covers structural components and kits which are referred to as structural construction products in this document. This document gives information that clarifies when a structural construction product is covered by the scope of EN 1090-1:2009+A1:2011 and lists examples of products covered and not covered, 2 Normative references ‘The following documents, in whole or in part, are referenced in this document and are indispensable for its application, For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1090-1:2009+A1:2011, Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components EN 1090-2:2008+A1:2011, Execution of steel structures and aluminium structures - Part 2: Technical requirements for steel structures EN 1090-3:2008, Execution of steel structures and aluminium structures - Part 3: Technical requirements {for aluminium structures 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 34 Harmonized Standard for construction products (hEN) standard adopted by one of the European standardisation bodies listed in Annex! to Directive 98/34/EC, on the basis of a request issued by the Commission, in accordance with Article 6 of that Directive, and which has been cited in the Official Journal of the European Union (JEU) as a harmonized standard under the Construction Products Regulation (EU) 305/2011/EC 32 European Assessment Document (EAD) document on the basis of the EU Construction Products Regulation EU 305/201 adopted by the organisation of Technical Assessment Bodies for the purposes of issuing European Technical Assessments 3.3 European Technical Assessment (ETA) documented assessment of the performance of a construction product in relation to its essential characteristics, in accordance with the respective European Assessment Document 34 European Technical Approval (ETA) favourable technical assessment of the fitness for use of a product for an intended use on the basis of the Construction Products Directive (89/106/EEC), based on fulfilment of the essential requirements for construction works for which the product is used Note 1 toentry: According to EU 305/2011/EG, article 66, 4) European technical approvals may be used as European Technical Assessments throughout the period of validity of those approvals. right fo reproduce and distribute belongs to the Estonian Centre for ngle-user licence. Order No. 214329, 5/22/2017, 5 8 Right of Use of this electronic document: Enrico35 European Technical Approval Guidelines (ETAG) guideline for the issuing of a European Technical Approval on the basis of the EU Construction Products Directive (89/106/EEC) Note toentry: According to EU 305/2011/EC, article 66, 3) ETAGs may be used as EADs. 4 Conditions necessary for construction products to be covered by the scope of EN 1090-1 Construction products are covered by the scope of EN 1090-1:2009+A1:2011 when all the following conditions are satisfied: ‘The product fulfils the requirements of EN 1090-2 or EN 1090-3 Condition 2: The product is a structural construction product within the meaning of the Construction Products Regulation (EU) 305/201 which means: Condition 2a: ‘The product is intended to be incorporated in a permanent manner in construction works (buildings or civil engineering works), and Condition 2b: The product has a structural function in relation to the construction work (ie. its failure will affect the satisfaction of Basic Requirement 1 and subclause a) of Basic Requirement 2 as detailed in 5.3.2 and Annex I of the Construction Products Regulation (EU) 305/2011/EC). Condition 3: This European Standard does not apply to construction products covered by another European technical specification (eg. a specific harmonized standard (hEN) or a European Technical Approval or European Technical Assessment (ETA)). 5 Clarification 5.1 General In this clause further clarification of the conditions of Clause 4 is given. Structural construction products are part of a loadbearing construction which is an organized assembly of connected parts designed to provide mechanical resistance and stability to the works. A way of identifying a structural construction product is to ask the question: “If the product is removed does its removal affect the strength and stability of the structure or a part of the structure?”. Ifthe answer to this question is yes then the product is a structural construction product, see also EN 1090-1:2009+A1:2011, 3.1.9. For indicative, non-exhaustive, lists_of products covered and not covered by the scope of EN 1090-1:2009+A1:2011, see Annex A and Annex B of this document. 5.2 Condition 1 - The product fulfils the requirements of EN 1090-2 or EN 1090-3 For a product to fall within the scope of EN 1090-1 the processes for its manufacture shall comply with EN 1090-2 or EN 1090-3. 5.3 Condition 2 - The product is a structural construction product within the meaning of the Construction Products Regulation (EU) 305/2011 8.3.1 Condition 2a - The product is intended to be incorporated in a permanent manner in construction works a) Incorporated ina permanent manner ibute belongs to the Estonian Centre for Standardisation io reproduce and di Single-user licence. Order No, 214329, Right of Use of this electronic document: Enrico COSTA, theCEN/TR 17052:2017 (E) Incorporation of a product in a permanent manner in the works means: — that its removal reduces the performance capabilities ofthe works and — that the dismantling or the replacement of the product are operations which involve construction activities. ‘Typical construction products that are not incorporated in a permanent manner are scaffolding, formwork, falsework and temporary edge protection. b) Construction works Construction works means buildings and civil engineering works (as for instance bridges). Construction works are fixed to the ground. A construction work is to be regarded as “fixed to the ground” when it is directly or indirectly connected to the ground or is supported by the ground. Supported by the ground can be for instance by gravity or via piling, 5.3.2 Condition 2b - The product has a structural function in relation to the construction work ‘The product shall have a structural function in relation to the construction work (ie. its failure will affect the satisfaction of Basic Requirement 1 and subclause a) of Basic Requirement 2 as detailed in ‘Annex | of Regulation EU 305/2011). ‘These requirements are related to the mechanical resistance and stability of the “constru including the safety in case of fire. mn works” ‘The requirements are: ‘The construction works shall be designed and built in such a way that the loadings that are liable to act on them during their construction and use will not lead to any of the following (see Annex I of the Construction Products Regulation (EU) 305/2011/EC): a) Collapse of the whole or part of the work b) Major deformations to an inadmissible degree ©) Damage to other parts of the construction works or to fittings or installed equipment as a result of major deformation of the load-bearing construction; 4) Damage by an event to an extent disproportionate to the original cause. In certain cases the construction works shall also be designed and built in such a way that in the event of an outbreak of fire the load-bearing capacity of the construction can be assumed for a specific period of time. ‘The “load-bearing construction” is a sub-set of the construction works and includes all those construction products that contribute to the strength and stability and to the safety in case of fire of the works. This includes both the main load-bearing elements (eg. the frame, walls, columns, beams, bracing, connectors, foundations) and the secondary load bearing elements (e.g. structural claddings, purlins, decking). Basic requirement No. 1 for construction works applies to the load bearing elements covering a wide range of structural construction products. Examples of such products that may form part of the construction work are given in Annex A. NOTE Some of these elements might also be covered by Basic requirement No. 4 for construction works, which is not addressed in EN 1090-1. Safety in use, in terms of unacceptable risks of accidents or damage in service or operation, is concerned with Basic requirement No. 4 for construction works. user licence. Order No. 214329, 5/22/2017. Single . Right of Use of this electronic document: Enrico COSTA, the right fo reproduce and distribute belcngs to the Estonian Centre for Standardis:CEN/TR 17052:2017 (E) 5.4 Condition 3 - The product is not covered by another European technical specification 5.4.1 General ‘The following types of technical specifications are meant here: — harmonized standard or — ETA European Technical Assessment or still valid European technical approval). 5.4.2 Construction products covered by another harmonized standard Construction products the performance of which can be assessed by other harmonized standard(s) do not fall within the scope of EN 1090-1. There are many construction products that are assessed in accordance with their own separate harmonized standard some of which are given in Table 1. Table 1 — Alist of harmonized standards for construction products that do not fall under the scope of EN 1090-1 Harmonized Standard EN 40-5 Lighting columns - Part 5: Requirements for steel lighting columns EN 40-6 Lighting columns - Part 6: Requirements for aluminium lighting columns | EN 845-1 Specification for ancillary components for masonry - Part 1: Wall ties, tension straps, hangers and brackets Specification for ancillary components for masonry - Part 2: Lintels Road restraint systems - Part 5: Product requirements, test and assessment methods and acceptance criteria EN 1337-3 Structural bearings - Part 3: Elastomeric bearings EN 1337-4 Structural bearings - Part 4: Roller bearings EN 1337-5 Structural bearings - Part 5: Pot bearings EN 1337-6 Structural bearings - Part 6: Rocker bearings EN 1337-7 Structural bearings - Part 7: Spherical and cylindrical PTFE bearings EN 1337-8 Structural bearings - Part 8: Guide Bearings and Restraint Bearings EN 1856-1 Chimneys - Requirements for metal chimneys - Part 1: System chimney products EN 1856-2 Chimneys - Requirements for metal chimneys - Part 2: Metal flue liners and connecting flue pipes EN 10025-1 Hot rolled products of structural steels - Part 1: General technical delivery conditions EN 1088-4 Stainless steels - Part 4: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for construction purposes EN 1008-5 Stainless steels - Part 5: Technical delivery conditions for bars, rods, wire, sections and bright products of corrosion resisting steels for construction purposes ight fo reproduce and distribute belongs to the Estonian Centre for Standardisation, Single-user licence. Order No. 214329, 5/22/2017. Right of Use of this electronic document: Enrico COSTA,CEN/TR 17052:2017 (E) user licens, Order No, 214329, 5/22/2017. Sin EN 10210-1 Hot finished structural hollow sections of non-alloy and fine grain steels - Part 1: Technical delivery conditions EN 10219-1 Cold formed welded structural hollow sections of non-alloy and fine grain steels Part 1: Technical delivery conditions EN 10248-1 Hot-rolled steel sheet piling - Part 1: Technical delivery conditions EN 10249-1, Cold-formed steel sheet piling - Part 1: Technical delivery conditions EN 10340 Steel castings for structural uses EN 10343 Steels for quenching and tempering for construction purposes - Technical delivery conditions EN 12285-2 Workshop fabricated steel tanks - Part 2: Horizontal cylindrical single skin and double skin tanks for the aboveground storage of flammable and non- flammable water polluting liquids EN 1289-1 Fixed, vertical road traffic signs ~ Part 1: Fixed signs EN 13084-7 Free-standing chimneys ~ Part 7: Product specifications of cylindrical steel fabrications for use in single wall steel chimneys and stee! liners EN 13241-1 Industrial, commercial and garage doors and gates - Product standard ~ Part 1: Products without fire resistance or smoke control characteristics EN 13445-3 Unfired pressure vessels ~ Part 3: Design EN 13479 Welding consumables ~ General product standard for filler metals and fluxes for fusion welding of metallic materials EN 13561 External blinds - Performance requirements including safety EN 13659 Shutters ~ Performance requirements including safety EN 13830 Curtain walling ~ Product standard EN 14195, Metal framing components for gypsum board systems - Definitions, requirements and test methods EN 14351~1 Windows and doors - Product standard, performance characteristics - Part 1: Windows and external pedestrian doorsets without resistance to fire and/or smoke leakage characteristics EN 14388 Road traffic noise reducing devices ~ Specifications EN 14399-1 High-strength structural bolting assemblies for preloading - Part 1: General requirements EN 14509 Self-supporting double skin metal faced insulating panels - Factory made products - Specifications EN 14545, Timber structures ~ Connectors ~ Requirements EN 14592 ‘Timber structures - Dowel-type fasteners - Requirements EN 14782 Self-supporting metal sheet for roofing, external cladding and internal lining ~ Product specification and requirements EN 14783 Fully supported metal sheet and strip for roofing, external cladding and internal lining - Product specification and requirements EN 15048-1 Non-preloaded structural bolting assemblies - Part 1: General requirements ribute belongs to the Estonian Centre for Standardisation, Tight fo reproduce and di Osta, Right of Use of this electronic document: Entice C!CEN/TR 17052:2017 (E) EN 15088 Aluminium and aluminium alloys - Structural products for construction works ~ Technical conditions for inspection and delivery EN 16034 Pedestrian doorsets, industrial, commercial, garage doors and openable windows ~ Product standard, performance characteristics - Fire resistance and/or smoke control characteristics Many of the construction products listed in Table 1 form the constituent products that are used to manufacture construction products which are assessed according to EN 1090-1. Hot rolled products of structural steels according to EN 10025-1 or structural aluminium products according to EN 15088 are just some examples of the constituent products that are used to make fabricated structural products, that are assessed according to EN 1090-1, 5.4.3 Construction products covered by an ETA Structural steel and aluminium components that are covered by an ETA (European Technical Assessment or a still valid European Technical Approval) are not covered by EN 1090-1. ‘A non-exhaustive list of products covered by ETAs based on ETAGs used as EADs is given in Table 2 below. Table 2—A list of ETAs for construction products not covered by EN 1090-1 ETA according to | Component ETAG used as EAD ETAG 001, Metal Anchors for use in Concrete ETAG 008 Prefabricated stairs kits ETAG 015 ‘Three-dimensional nailing plates ETAG 023 Prefabricated building units ETAG 025a Metal frame building kits Note: include structural frame, cladding and foundations. ETAG 029 Metal injection anchors for use in masonry ETAG 030 Dowels for structural joints ETAG 032 Expansion joints for road bridges ETAG 034-1 Kits for external Wall Claddings - Part 1: Ventilated cladding kits comprising cladding components and associated fixings ETAG 034-2 Kits for external Wall Claddings ~ Part 2: Claddings kits comprising cladding components, associated fixings, subframe and possible insulation layer a__ Inthe case of ETAGO25 two approaches are possible: — Approach 1: if a manufacture decides not to implement ETAGO25 then the requirements of EN 1090-1 shall apply to the structural metallic elements or kits. — Approach 2: If the manufacturer wants to consider the intended use as a building as specified in ETAG 025 and declare additional characteristic performances resulting from it (as a minimum, the connections to the ground and specifications for the elements of the building envelope) not taken into account by EN 1090-1, then ETAG 025 appli There are too many ETAs to list in this publication. A complete list is given on the EOTA website 10 8 iif ibute belongs sence, Order No. 214329, 5/22/2017 ight to reproduce and di Single-user Right of Use of this electronic document: Enrico COSTA, theCEN/TR 17052:2017 (E) Annex A (informative) Products covered by EN 1090-1 ‘The following steel and aluminium products are covered by the scope of EN 1090-1, when the intended use comprises a structural function. This list is indicative and non-exhaustive, Structural components / Structural components for: AA Balconies, A2 Balustrades if fulfilling the function of a barrier 1) A3 Base plates, AA Beams not covered by EN 1025-1, AS Beam clamps without ETA, AG —_ Bended products from hot rolled beams and steel plates, AT Bracing, AB Bridges (incl. road-, railway- and footbridges, pipe bridges, moving bridges), AQ Buildings, A10 Canopy framing, All Carports, A12 — Catwalks, A13 Cellular Beams, A14 Chimneys not covered by EN 1856-1 or EN 1856-2 or EN 130847, AAS Cold-formed purlins and cladding rails, A.16 — Cold-formed sheeting for roofing and cladding if structural, A17 —Cold-formed decking for use in composite steel and concrete floors, Single-user licence. Order No. 214329, 5/22/2017. 0 COSTA, the right fo reproduce and distribute belongs to the Estonian Centre for Standardisation, A18 Columns, A19 Crane supporting structures including crane runway beams, crane rails and structural end stops, A20 Culverts used as a bridge-like structure to carry traffic, A21 Curved and bent beams, 22 Cutto size components from hot rolled products, A23 Fire escapes, A24 — Girders not covered by EN 10025-1,, 25 Grandstands and stadia, Right of Use of this electronic document: Enriot 1) seealso European Commission's FAQ website (FAQ 31) aCEN/TR 17052:2017 (E) A26 A27 A28 A29 A30 AB1 A32 A33 A34 A385 A36 A37 A38 A39 AAO AAL AA2 AaB AAS AAS A46 AAT AAB AAo ASO ASL AS2 AS3 AS4 ASS AS6 AST ASB AS9 12 Grillage beams and girders, Handrails (Barriers / Edge Protection), Hangers not covered by EN 845-1 and ETAG 015, Lighting columns neither covered by EN 40-5 or EN 40-6 nor by an Lintels not covered by EN 845-2, Load bearing fences, Marquee framing, Machined or bended aluminium semiproducts for use as structural components, Machinery supports, ifintegral part of the load bearing structure of the construction works, Masonry structures not covered by EN 845~1, EN 845-2, or ETAG 029, Metal frame building kits without ETA, Mezzanine floors, Noise barriers, not covered by EN 14388, Opening frames for floors, walls and roofs, if integral part of the load bearing structure of the construction works, Pipeline supporting structures and pipe supporting structures, Plant and machinery, if integral part of the load bearing structure of the construction works, Plate girders (welded or bolted or riveted), Prefabricated building units without ETA, Prefabricated pile foundations without ETA, Predrilled components from hot rolled beams and steel plates, Purlins, Racking and shelving systems, if integral part of the load bearing structure of the construction works, Ramps, if integral part of the load bearing structure of the construction works, Sag rods, Sign and gantry girders, Silos, Stairs without ETA, Structural frames for buildings, warehouses, schools, hospitals, dwellings, industrial and agricultural sheds, Structural frames for shelters, Structural steel components for composite steel and concrete structures, ‘Tanks that are not covered by EN 1285-2, Tension rods without ETA, Timber structures excluding fasteners, Towers and masts, the right to reproduce and distribute belongs to the Estonian Centre for Standardisation. Right of Use of this electronic document: EnricoCEN/TR 17052:2017 (E) A60 Trusses, A61 Tubular beams and columns, A62 Walkways, incl. open mesh flooring, if integral part of the load bearing structure of the construction works, 63 Wharfs, docks and piers, A64 — Winter gardens and green houses. longs to the Estonian Centre for Standardisation. Single-user licenoe. Order No. 214329, 51221 Right of Use of this electronic document: Enrico COSTA, the right to reproduce and distribu 13CEN/TR 17052:2017 (E) Annex B (informative) Products not covered by EN 1090-1 ‘The following steel and aluminium products are not covered by the scope of EN 1090-1. This list is indicativeand non-exhaustive. 2) Ba Ba2 B3 Ba BS BS BT BS BO B10 Bat BA2 B.13 Bat B.S B.i6 BA7 Bis Bao B20 B21 B22 B23 Bust a 14 Aluminium and aluminium alloys ~ Structural products for construction works according to EN 15088, Aluminium structural comp. es, Amusement rides and devices which are machines or not permanently installed, Balustrades unless fulfilling the function of a barrier, 3) Beam clamps with ETA, Bearings and steel components used in bearings according to EN 1337, Blind rivets, Cabinets for cables and power supply installations, Cables, ropes and wires, Castings, Circulation fixtures except sign gantry and cantilevers, Cladding kits according to ETAG 034, Cold formed steel tubes according to EN 10219-1, Cold storage premises according to ETAG 021 Components for suspended ceilings, Composite light weight panels according to ETAG 016 Curtain walling according to EN 13830, Doors according to EN 14351-1, Dowels for structural joints according to ETAG 030, Expansion joints for road bridges according to ETAG 032, External blinds according to EN 13561, Fasteners glued to timber structures, Fastening plates and other cast into concrete fasteners not covered by design standards, codes and regulations Flagpoles, For Wind Turtsines and their Towers, see European Commission's FAQ website (FAQ 31) 3) See also Eure sslon's FAQ website the Estonian Centre for Standardisation ser licence. Order No. 214329, 57221201 cus Hoenee yoproguce and diibute belongs to! Sing Right of Use ofthis electronic document Enrico COSTCEN/TR 17052:2017 (E) B58 B59 B60 B61 B62 B63 B64 Bes, B66 B67 B68. B69 B70 B71 B72 B73 B74 B75 B76 B77 B78 B79 B80 Bal B82 B83 B84 B85 B86 B87 B88 B89 16 Raised floors, Reinforcing steel for concrete or masonry, Road parapets, crash barriers, crash cushions according to EN 1317-5, Road traffic noise reducing devices according to EN 14388, Roof safety products incl. roof ladders and walkways, Scaffoldings, Sculptures (Metal Art), Sandwich panels according to EN 14509, Self-drilling and self-tapping screws, Self-supporting metal sheets for roofing, cladding and lining according to EN 14782, Sheet piling according to EN 10248-1 and EN 10249-1, Shutters according to EN 13659, Stainless steel sheet/plate and strip according to EN 10088-4, Stainless stee! bars, rods, wire, sections according to EN 10088-S, Steel and aluminium components and elements produced on site, Steel and aluminium stairs, walkways and fences forming integral part of a machine, silo, tank, etc, Steel beams for composite steel concrete structures not covered by design standards, codes and regulations, Steel casting for structural use according to EN 10340, Steels for quenching and tempering for construction purposes according to EN 10343, Steel lintels according to EN 845-2, Steel spring elements, Structural components for offshore structures, Structural double skin metal faced sandwich panels, Tanks - Workshop fabricated steel tanks according to EN 1285-2, ‘Temporary structures (eg. tents, fairground and amusement park machinery and structures) ‘Three-dimensional nailing plates according to ETAG 015, Ties, tension straps, hangers and brackets for masonry according to EN 845-1, Timber connectors according to EN 14545, ‘Timber dowel-type fasteners according to EN 14592, Traditional craft type and non-structural components (eg. weather cocks, letter boxes, bicycle racks, fences), ‘Traffic sign supports according to EN 12899-1, Tuned mass damper systems, Tight fo reproduce and distribute belongs to the Estonian Centre for Standardisation sence. Order No. 214329, 5/22/2017. Single-user Right of Use of this electronic document: Enrico COSTA, theCEN/TR 17052:2017 (B) Viscous liquid dashpot dampers, B90 ‘UORESIpIEPUEIS 40} B11UED UEIUOISY au 0} SB cording to EN 13479, Windows according to EN 14351-1. Welding consumables BOL B92 199 einquisip pue eanposdas 01 1yBu ou 'yLSO9 oouUy qUALINoDP ‘LLORI2zIS 'BZEPLZ “ON JapIO "eoUE0H| JasN-3|SuIS 1vouDeje sig Jo asf. Jo 1UBI 7