constructive solutions

Technical Submittal

CONPLAST CN
(Calcium nitrite corrosion inhibiting admixture)

Fosam Company Limited

Head Office
telephone: fax: email:
PO Box 11081
Jeddah – 21453 +966 (12) 637 5345 +966 (12) 637 5891 [email protected]
Saudi Arabia
C.R. No. 31273
Paid up Capital: SR3,000,000
www.fosroc.com Registered Office: Industrial Area, Phase 4, Road No. 102, Street No. 82
 constructive solutions

Technical Datasheet
Conplast CN constructive solutions

Calcium nitrite corrosion inhibiting admixture

Uses

Where calcium nitrite is specified for addition to concrete as a Conplast CN is suitable for use with ordinary Portland
corrosion inhibiting admixture. cement. Contact the Fosroc Technical Service Department
for advice on use with sulphate resisting cements and
Advantages cement replacement materials.

 Based on the main chemical type specified for use as a Dispensing

corrosion inhibitor in concrete.
The correct quantity of Conplast CN should be measured by
 Can be used in conjunction with other admixtures. means of a recommended dispenser. The admixture should
then be added to the concrete with the mixing water to
obtain the best results.
Description
Contact the Fosroc Technical Service Department for advice
Conplast CN admixture is based on calcium nitrite. It is regarding suitable dispensing equipment and its installation.
supplied as a pale straw coloured solution that instantly
disperses in water. Curing

Technical support As with all structural concrete, good curing practice should
be maintained. Water spray, wet hessian and/or Concure*
Fosroc provides a technical advisory service for on-site spray applied curing membranes should be used.
assistance and advice on mix design, admixture selection,
evaluation trials and dispensing equipment. Technical data Limitations
and guidance can be provided for admixtures and other
products for use with fresh and hardened concrete. Conplast CN may accelerate the set of concrete. This
should be checked during trials. Various grades of Conplast
Typical dosage retarding admixtures can be used to offset any undesired
effects.
Conplast CN should be used to give the addition level
required in concrete mix specification documents. Typical For optimum protection of reinforced concrete against
specified dosage levels are normally in the range of 7.5 to chloride attack the water cement ratio of the concrete must
22.5 litres per cubic metre of concrete. Because Conplast be kept to a very low level. Water cement ratios of below 0.4
CN has a high dosage level, calculation of water cement ratio should typically be specified for this purpose. The use of
should include the water added to the mix in the admixture. Conplast plasticisers and superplasticisers will be found
useful in obtaining this performance.

Properties
Estimating - Packaging
Appearance: Pale straw coloured liquid
Conplast CN is available in drum or bulk supply.
Chloride content: Nil to BS5075
Calcium nitrite content: 30% minimum
Storage

Instructions for use Conplast CN has s minimum shelf life of 12 months provided
o o
the temperature is kept within the range of 2 C to 50 C.
Compatibility Should the temperature of the product fall outside this range
then the Fosroc Technical Service Department should be
Conplast CN is compatible with other Fosroc admixtures in contacted for advice.
the same concrete mix. All admixtures should be added to
the concrete separately and must not be mixed together prior Conplast CN is an oxidising agent and should be stored
to addition. The performance of concrete containing more away from reducing agents and combustible materials.
than one admixture should be assessed by trial mixes to
ensure the desired combination of effects is obtained. If a joint is left unsealed for more than 4 hours, the primer
should be removed by grit blasting or grinding and the joint
re-primed.

For further advice on priming required please contact your

local Fosroc Technical Service Department.

Page 1
Conplast CN
Precautions

Health and safety

Conplast CN is toxic and should not be swallowed or

allowed to come into contact with skin and eyes.

Wear suitable protective gloves and goggles. Splashes on

the skin should be removed with water.

In case of contact with eyes rinse immediately with plenty of

water and seek medical advice. If swallowed seek medical
attention immediately . Do not induce vomiting

Fire

Conplast CN is water based and non-flammable but should

be stored away from combustible materials.

Cleaning and Disposal

Spillages of Conplast CN should be absorbed onto sand,

earth or vermiculite and transferred to suitable containers.
Do not allow Conplast CN to enter rivers or drains.

The disposal of excess or waste material should be carried

out in accordance with local legislation under the guidance
of the local waste regulatory authority.

Important note:
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions
for the Supply of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that
any advice, recommendation, specification of information it may give is accurate and correct, it cannot, because it has no direct
or continuous control over where or how its products are applied, accept any liability either directly or indirectly arising from the
use of its products, whether or not in accordance with any advice, specification, recommendation of information given by it.

Fosam Company Limited

Telephone: +966 2 637 5345 Fax: +966 2 637 5891 email: [email protected]
Head Office
Post Box 11081 Regional Offices
Jeddah Sales Office Tel: (02) 608 0999 Fax: (02) 638 0693 Yanbu Tel: (04) 322 4280 Fax: (04) 391 2980
Jeddah – 21453
Jeddah Showroom Tel: (02) 665 0187 Fax: (02) 667 4844 Makkah Tel: (02) 542 0869 Fax: (02) 542 0869
Saudi Arabia Riyadh Tel: (01) 482 9303 Fax: (01) 482 7562 Medinah Tel: (04) 855 0091 Fax: (04) 855 0047
Dammam Tel: (03) 814 1282 Fax: (03) 814 1581 Jubail Tel: (03) 362 3904 Fax: (03) 362 3875

www.fosroc.com Khamis Mushayt Tel: (07) 250 0469 Fax: (07) 250 0469 CSD Tel: (02) 608 0999 Fax: (02) 638 0693

Registered Office: Industrial Area, Phase 4, Road No. 414, Street No. 407
Page 2 FO SA/CONPLAST CN/05/A
 constructive solutions

Material Safety
Datasheet
Revision date: 31/08/2016 Revision: 06 Supersedes date: 08/06/2015

SAFETY DATA SHEET

CONPLAST CN

SECTION 1: Identification of the substance/mixture and of the company/undertaking

1.1. Product identifier

Product name CONPLAST CN

Product number M1234000

Container size 25 Litre Pail, 210 Litre Drum, 1000 Litre IBC

1.2. Relevant identified uses of the substance or mixture and uses advised against
Identified uses Corrosion inhibitor.

1.3. Details of the supplier of the safety data sheet

Supplier FOSAM COMPANY LTD
Phase 4,Road 414 , Street 82
Post Box 11081 Jeddah 21453
K.S.A
+966126375345
+966126080999
+966126375891

1.4. Emergency telephone number

Emergency telephone +966 126375345 , +966216080999

SECTION 2: Hazards identification

2.1. Classification of the substance or mixture

Classification (EC 1272/2008)
Physical hazards Not Classified

Health hazards Skin Irrit. 2 - H315 Eye Irrit. 2 - H319 Skin Sens. 1 - H317

Environmental hazards Not Classified

Classification (67/548/EEC or Not a hazardous substance or mixture according to EC-directives 67/548/EEC or 1999/45/EC
1999/45/EC)

Human health See Section 11 for additional information on health hazards.

Environmental The product is not expected to be hazardous to the environment.

2.2. Label elements

Pictogram

Signal word Warning

1/7
Revision date: 31/08/2016 Revision: 06 Supersedes date: 08/06/2015

CONPLAST CN

Hazard statements H315 Causes skin irritation.

H317 May cause an allergic skin reaction.
H319 Causes serious eye irritation.

Precautionary statements P280 Wear protective gloves/ protective clothing/ eye protection/ face protection.
P302+P352 IF ON SKIN: Wash with plenty of water.
P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove
contact lenses, if present and easy to do. Continue rinsing.
P332+P313 If skin irritation occurs: Get medical advice/ attention.
P337+P313 If eye irritation persists: Get medical advice/ attention.
P501 Dispose of contents/ container in accordance with national regulations.

Supplementary precautionary P261 Avoid breathing vapour/ spray.

statements P264 Wash contaminated skin thoroughly after handling.
P272 Contaminated work clothing should not be allowed out of the workplace.
P321 Specific treatment (see medical advice on this label).
P333+P313 If skin irritation or rash occurs: Get medical advice/ attention.
P362+P364 Take off contaminated clothing and wash it before reuse.

2.3. Other hazards

Not considered hazardous at ambient temperature.

SECTION 3: Composition/information on ingredients

3.2. Mixtures
Composition comments 30 % Solution of Calcium Nitrite

SECTION 4: First aid measures

4.1. Description of first aid measures

Inhalation Remove from exposure – Unlikely to occur.

Ingestion Wash out mouth with water. Do NOT induce vomiting. Obtain medical attention.

Skin contact Wash thoroughly with soap and water or suitable skin cleanser as soon as possible.

Eye contact Irrigate immediately with copious quantities of water for several minutes. Obtain medical
attention if irritation persists.

4.2. Most important symptoms and effects, both acute and delayed
Inhalation May cause irritation.

Ingestion May be harmful if swallowed.

Skin contact Prolonged or repeated contact with skin may cause irritation, redness and dermatitis.

Eye contact Repeated exposure may cause chronic eye irritation.

4.3. Indication of any immediate medical attention and special treatment needed
Notes for the doctor Treat symptomatically.

SECTION 5: Firefighting measures

5.1. Extinguishing media

Suitable extinguishing media Carbon dioxide, alcohol foam, foam or dry chemical extinguisher

5.2. Special hazards arising from the substance or mixture

Specific hazards May intensify fire; oxidiser.

2/7
Revision date: 31/08/2016 Revision: 06 Supersedes date: 08/06/2015

CONPLAST CN

Hazardous combustion Oxides of nitrogen.

products

5.3. Advice for firefighters

Protective actions during Not relevant.
firefighting

Special protective equipment Wear positive-pressure self-contained breathing

for firefighters apparatus (SCBA) and protective fire fighting clothing (includes fire fighting helmet, coat,
trousers,
boots, and gloves). If protective equipment is not available or not used, fight fire from a
protected
location or safe distance.

SECTION 6: Accidental release measures

6.1. Personal precautions, protective equipment and emergency procedures

Personal precautions Avoid inhalation of vapours.

6.2. Environmental precautions

Environmental precautions Avoid the spillage or runoff entering drains, sewers or watercourses.

6.3. Methods and material for containment and cleaning up

Methods for cleaning up Soak up with inert absorbent or contain and remove by best available means. Dispose of as
waste.

6.4. Reference to other sections

Reference to other sections For personal protection, see Section 8. For waste disposal, see Section 13.

SECTION 7: Handling and storage

7.1. Precautions for safe handling

Usage precautions Avoid contact with skin and eyes.

Advice on general Do not eat, drink or smoke when using this product.
occupational hygiene

7.2. Conditions for safe storage, including any incompatibilities

Storage precautions Store in cool, dry area. Store out of direct sunlight. Store away from acids.

Storage class Corrosive storage.

7.3. Specific end use(s)

Specific end use(s) The identified uses for this product are detailed in Section 1.2.

SECTION 8: Exposure Controls/personal protection

8.1. Control parameters

Occupational exposure limits
Not available.

8.2. Exposure controls

Protective equipment

3/7
Revision date: 31/08/2016 Revision: 06 Supersedes date: 08/06/2015

CONPLAST CN

Appropriate engineering Provide adequate ventilation. Observe any occupational exposure limits for the product or
controls ingredients.

Eye/face protection Wear splash resistant safety goggles with a faceshield. Provide an emergency eye wash
fountain and quick drench shower in the immediate work area.

Hand protection Wear appropriate chemical resistant gloves.

Other skin and body Wear appropriate chemical resistant clothing.

protection

Hygiene measures Use engineering controls to reduce air contamination to permissible exposure level. Provide
eyewash station and safety shower.

Respiratory protection Respiratory protection complying with an approved standard should be worn if a risk
assessment indicates inhalation of contaminants is possible.

SECTION 9: Physical and Chemical Properties

9.1. Information on basic physical and chemical properties

Appearance Liquid.

Colour Light (or pale).

Odour Typical

pH pH (concentrated solution): 8.0 - 9.0

Melting point Not applicable.

Initial boiling point and range Not available.

Flash point Not applicable.

Evaporation rate Not determined.

Evaporation factor Not determined.

Flammability (solid, gas) No data

Upper/lower flammability or No data

explosive limits

Relative density 1.260 - 1.280 @ 25°C

Solubility(ies) Soluble in water

Partition coefficient Not applicable.

Viscosity Not determined.

Explosive properties 300 ̊C

Oxidising properties Not applicable.

9.2. Other information

Other information Not available.

Peroxide content

SECTION 10: Stability and reactivity

10.1. Reactivity
Reactivity Stable at normal temperatures and pressure.

10.2. Chemical stability

4/7
Revision date: 31/08/2016 Revision: 06 Supersedes date: 08/06/2015

CONPLAST CN

Stability Stable.

10.3. Possibility of hazardous reactions

Possibility of hazardous Strong acids.
reactions

10.4. Conditions to avoid

Conditions to avoid Temperatures below 2°C.

10.5. Incompatible materials

Materials to avoid Strong alkalis. acids, aluminum metals, ammonium salts

10.6. Hazardous decomposition products

Hazardous decomposition Thermal decomposition:- Oxides of carbon. Sulphur compounds. Nitrogen compounds.
products

SECTION 11: Toxicological information

11.1. Information on toxicological effects

Toxicological effects not available.

Inhalation Mist and vapours may cause irritation to nose and repiratory tract.

Ingestion May cause internal injury.

Skin contact Unlikely to irritate on brief or occasional exposure.

Eye contact May cause transient irritation.

Acute and chronic health Prolonged or repeated exposure may cause severe irritation.
hazards

Route of entry Skin and/or eye contact

SECTION 12: Ecological Information

Ecotoxicity The environmental hazards associated with the product are considered to be limited

12.1. Toxicity
Toxicity Not considered toxic to fish.

12.2. Persistence and degradability

Persistence and degradability The degradability of the product is not known. This product is not expected to be readily
biodegradable.

12.3. Bioaccumulative potential

Bioaccumulative potential No data available on bioaccumulation.

Partition coefficient Not applicable.

12.4. Mobility in soil

Mobility Mobile liquid. Soluble in water.

12.5. Results of PBT and vPvB assessment

Results of PBT and vPvB This product does not contain any substances classified as PBT or vPvB.
assessment

12.6. Other adverse effects

5/7
Revision date: 31/08/2016 Revision: 06 Supersedes date: 08/06/2015

CONPLAST CN

Other adverse effects None known.

SECTION 13: Disposal considerations

13.1. Waste treatment methods

Disposal methods Disposal must be in accordance with local and national legislation.
Unused Product: Dispose of through an authorised waste contractor to a licensed site.
Used/Contaminated Product: As for Unused product.
Packaging: May be steam cleaned and recycled.

SECTION 14: Transport information

General This product is NOT classified as dangerous for transportation

14.1. UN number
This Product is not classified as dangerous for transport

14.2. UN proper shipping name

Not applicable.

14.3. Transport hazard class(es)

No transport warning sign required.

14.4. Packing group

Not applicable.

14.5. Environmental hazards

Environmentally hazardous substance/marine pollutant

No.

14.6. Special precautions for user

Not applicable.

14.7. Transport in bulk according to Annex II of MARPOL and the IBC Code
Transport in bulk according to Not applicable.
Annex II of MARPOL 73/78
and the IBC Code

SECTION 15: Regulatory information

15.1. Safety, health and environmental regulations/legislation specific for the substance or mixture
National regulations No listing known. The Chemicals (Hazard Information and Packaging for Supply) Regulations
2009 (SI 2009 No. 716). Control
of Substances Hazardous to Health Regulations 2002 (as amended).

Guidance Introduction to Local Exhaust Ventilation HS(G)37.

15.2. Chemical safety assessment

No chemical safety assessment has been carried out.

SECTION 16: Other information

Revision date 31/08/2016

Revision 06

Risk phrases in full Not classified.

6/7
Revision date: 31/08/2016 Revision: 06 Supersedes date: 08/06/2015

CONPLAST CN

Hazard statements in full H315 Causes skin irritation.

H317 May cause an allergic skin reaction.
H319 Causes serious eye irritation.

Supersedes date 08/06/2015

SDS number SDS M1234000 KSA

SDS status Approved.

The information on this data sheet represents our current data and is reliable provided that the product is used under the
prescribed conditions and in accordance with the application specified on the packaging and/or in the technical guidance
literature. Any other use of the product which involves using the product in combination with any other product or any other
process is the responsibility of the user.

7/7
 constructive solutions

Test Reports
 constructive solutions

Job References
 Job References for Conplast CN
Sorted by ascending Project Category and ascending Project Date

Project Title Sector Segment Main Contructor Country Quantity Units Date
Public &
KACC Buildings Institutional Project build Saudi Arabia 60,000 Litre(s) 15/01/2014
Buildings
Power Oil, Gas,
QURAYA POWER PLANT Utilities Samsung Saudi Arabia 300,000 Litre(s) 10/07/2013
Coal
Power Oil, Gas,
SOUTH JEDDAH POWER PLANT Utilities HYANDAI Saudi Arabia 80,000 Litre(s) 8/06/2013
Coal
Chemical &
HADEED DRP Industrial Dywidag Saudi Arabia Saudi Arabia 120,000 Litre(s) 11/09/2011
Process
Rakan Trading and
HADEED HOUSING PROJECT Buildings Residential Saudi Arabia 90,000 Litre(s) 11/09/2011
Contracting
HADEED HRM Buildings Residential Dywidag Saudi Arabia Saudi Arabia 160,000 Litre(s) 11/09/2011
Chemical &
IBN ZAHR EXPANSION PROJECT Industrial Saudi Bin Laden Group Saudi Arabia 75,000 Litre(s) 11/09/2011
Process
PETROKEMYA OLLIFENS III Industrial Oil & Gas Dywidag Saudi Arabia Saudi Arabia 300,000 Litre(s) 11/09/2011
Chemical &
SHARQ 3RD EXPANSION PROJECT Industrial Saudi Bin Laden Group Saudi Arabia 300,000 Litre(s) 11/09/2011
Process
Consolidated Contracting
JUBAIL CHEVRON PHILIPS PROJECT Industrial Oil & Gas Saudi Arabia 200,000 Litre(s) 10/09/2011
Company (CCC)
GAS AIR SEPARATION PROJECT Industrial Oil & Gas Dywidag Saudi Arabia Saudi Arabia 150,000 Litre(s) 11/07/2011
Chemical &
HADEED ROLLING MILL Industrial Dywidag Saudi Arabia Saudi Arabia 160,000 Litre(s) 11/07/2011
Process
Naser S. Al Hajiri
KAYAN - FELONICS FACILITY Buildings Commerical Saudi Arabia 250,000 Litre(s) 11/07/2011
Corporation
Chemical &
PETROKEMYA POLYETHELENE PROJECT Industrial MMG Saudi Arabia 200,000 Litre(s) 11/07/2011
Process
Chemical &
PILING FOR SINOPIC PROJECT IN KAYAN Industrial Keller - Turki Saudi Arabia 120,000 Litre(s) 11/07/2011
Process
Power Oil, Gas, Naser S. Al Hajiri
SAMSUNG APPC PROJECT Utilities Saudi Arabia 140,000 Litre(s) 11/07/2011
Coal Corporation
Power Oil, Gas, Naser S. Al Hajiri
TASNEE ETHYLENE PLANT Utilities Saudi Arabia 200,000 Litre(s) 11/07/2011
Coal Corporation
 QANBAR.RAZZAK/SAUDI
SAUDI KAYAN Industrial Oil & Gas Saudi Arabia 800,000 Litre(s) 15/02/2009
R MIX
DAMON BLDG PROJECT Buildings Commerical -- UAE 410,000 Lltrs 31/03/2008
LEISURE & CLUB HOTEL Buildings Commerical Zeptas Zimen UAE 300,000 Lltrs 31/03/2008
SHEIKH ZAYED BRIDGE PROJECT
Transport Road M/S ARCHIRODON UAE 700,000 Ltrs 31/03/2008
(ABUDHABI)
26/03/2008
KHURSANIYA GAS PLANT Industrial Oil & Gas Technip/Bechtel Saudi Arabia 3,000 Litre(s) 23/07/2007
Power Oil, Gas,
CONTROL TOWER BUILDING AT HALUL Utilities DOPET Qatar 15,000 Litre(s) 13/11/2006
Coal
RAS LAFFAN LIQUID PRODUCT BERTHS Power Oil, Gas, M/S ARCHIRODON
Utilities Qatar 295,000 Litre(s) 13/11/2006
3A & 3B Coal Construction Overseas
Cement &
YANSAB LLPE PLANT Industrial Sinopec Saudi Arabia 300,000 Litre(s) 24/09/2006
Concrete
Cement &
YANSAB PP PLANT Industrial Sinopec Saudi Arabia 300,000 Litre(s) 24/09/2006
Concrete
SIHANOUVILLA JETTY Transport Marine Penta Ocean, Japan Vietnam 30,000 Litre(s) 8/06/2006
CONTROL TOWER BUILDING AT HALUL Power Oil, Gas,
Utilities DOPET Qatar 15,000 Litre(s) 18/04/2006
(GTC-246/EF-03) Coal
RAS LAFFAN LIQUID PRODUCT BERTH 3A Archiroddon const
Industrial Oil & Gas Qatar 295,000 Litre(s) 24/07/2005
& 3B (Overseas),Qatar
Fujairah National
COMMERCIAL TOWER Buildings Commerical UAE 5,000 Ltrs 19/05/2004
Contracting Company
DESALINATION PLANT Utilities Water SIX CONSTRUCT UAE 1,100,000 Ltrs 19/05/2004
Chemical &
GRC FACTORY Industrial Arabesque UAE 250 Ltrs 19/05/2004
Process
Public &
HOSPITAL Buildings Institutional AL Owaidah Group Saudi Arabia 17,000 Ltrs 19/05/2004
Buildings
Power Oil, Gas,
MEW BUFFER TANKS Utilities Al Hamed Dev & Const UAE 15,000 Ltrs 19/05/2004
Coal
Consolidated contracting
OIL COMPANY Industrial Oil & Gas Saudi Arabia 85,000 Ltrs 19/05/2004
in'l co.
Chemical &
PTA AND AROMATIC PLANT Industrial Bechtel Saudi Arabia 200,000 Ltrs 19/05/2004
Process
RESIDENTIAL BUILDING Buildings Commerical Gulf Interstate UAE 10,000 Ltrs 19/05/2004
SICIM PIPELINE Utilities Water Huraibi UAE 15,000 Ltrs 19/05/2004
Public &
Satnam Namitha
NAVAL ACADEMY - PHASE II Buildings Institutional India 490,000 Kilogram(s) 19/03/2004
Associates Chandigarh
Buildings
Public &
NAVAL ACADEMY PROJECT - PHASE I Buildings Institutional RDS Projects Ltd. India 6,600 Litre(s) 19/03/2004
Buildings
Chemical &
SABIC ACETIC ACID PLANT Industrial Technip Saudi Arabia 28,000 Litre(s) 29/12/2003
Process
Power Oil, Gas, Afcons Infrastructure
TANVIR BHAVI Utilities India 50,000 Litre(s) 3/12/2001
Coal Ltd.
ARABIAN OIL COMPANY/ AL KHAFJI Industrial Oil & Gas C.C.C Saudi Arabia 85,000 Litre(s) 23/09/2000
SLAUGHTER HOUSE Industrial Agriculture AL Owaidah Group Saudi Arabia 1,000 Litre(s) 23/09/2000
YANPET Buildings Residential GAC Saudi Arabia 41,000 Litre(s) 23/09/2000
Al Hamed Developments
M.E.WATER BUFFER TANKS IN N.E Utilities Water UAE 65,000 Litre(s) 25/07/2000
And Construction
 constructive solutions

Approvals
 constructive solutions

Case Histories
 CASE STUDY

constructive solutions
JEC - JPDR
JIZAN - Saudi Arabia

CUSTOMER
Saudi Aramco

SECTOR
Infrastructure

DATE
2014

PRODUCTS
 Conplast SP500
 Conplast CN
 Reebol Formcote
 Concure 90 & Concure AB
 Nitocote SN502

THE PROJECT
Jizan Terminal Dredging Backfill Project in Saudi Arabia is an important terminal dredging project
the Government of Saudi Arabia build to for the construction of Jizan Economic City, especially the
construction of large industrial districts, such as Saudi Aramco Refinery. It is also the first large-
scale dredging hydraulic project since Saudi Aramco took over the management of Jizan Economic
City. The project site is about 100km away from Jizan City and it is a port infrastructure project of
Jizan Economic City. This project will include basin and channel dredging, land area reclamation by
pumping filling, breakwater and revetment construction and a heavy-piece terminal and its
subsidiary. The project is still on progress by China Harbor Engineering Arabia Co. ‘CHEC’.

One of 5 Site batching plants

THE SOLUTION
Fosroc team joined the contractor from the first stage of the project & made all trials to achieve
the requirements of the concrete. The client achieved the high quality results starting from the first
stage with more than 0.75% million liters of Fosroc admixtures, Conplast SP500, 440M & CN. To get
the highest quality of the 1500 concrete blocks, a release agent (NITOCOTE FORMCOTE), a curing
compound (CONCURE 90 & CONCURE AB) & a final cote with silane-siloxane material (NITOCOTE
SN502) have been used due to Fosroc team recommendation. Fosroc team kept following up the
contractor to support him & make sure that products’ applying is going properly.

Side view of concrete blocks

THE BENEFITS
Some of the advantages of FOSROC Constructive Solutions were as follows;

- The client was very satisfied according to FOSROC team’s support & the clearance of
Application Instructions.
- The client benefitted from being able to contract with a single party for the various types
of construction solutions.
- Contractors needed an economical & high quality solution that could be applied rapidly.
Again, FOSROC was able to meet this need.

Designed view of JEC port

T: +966 126080999 F: +966 12 6380693 E: [email protected]

Address: Jeddah Industrial Area Phase 4, Road 414, Street 407. Jeddah – Saudi Arabia www.fosroc.com