RhA
Rate of Rise/Fixed Temperature
Heat Detector
Features
• Adjustable fixed 135° to 174° Fahrenheit
• Rate of rise feature with 10-12°F per minute detection
• LEDs for 360° viewing
• Low profile
• Reliable detection technology
S24776 7270-0328:0193
Product includes a 5 year warranty
Description panel.
The combination Rate of Rise/Fixed Temperature Heat Sensor (RHA)
Before connecting a device to the SLC loop, take the following
is a listed Analog/Addressable combination temperature heat sensor
precautions to prevent potential damage to SLC or device. Verify the
compatible with any fire alarm control panel that has the Potter/
following:
Nohmi protocol. The heat sensing portion utilizes a proven thermistor
for accurate and reliable heat detection. The sensor and base (not 1. Power to the device is removed
included) are made of a durable plastic in an eggshell white (off white) 2. Field wiring is correctly installed.
to blend in with the ceiling. 3. Field wiring has no open or short circuits.
Document discrepancies and notify appropriate personnel.
The RHA is UL and cUL listed with a selectable fixed temperature
point from 135° to 174° and a rate of rise feature. The rate-of-rise
operates when the temperature increases 12-15°F occurs. The heat Specifications
sensor is ideal for installations needing the earlier heat detection. Item FHA
Working voltage range 22.0 to 24.0 V
The RHA has two LEDs that allow for 360° viewing. The sensor is
compatible with any of the Potter/Nohmi bases and simply twists on. Standby current 325 µA
The RHA is addressed using the hand held programmer or the control Alarm indicator 2 LEDs
panel addressing function.
Alarm indicator current 1.2 mA D.C.
Spacing Alarm set-point range 135 to 174 °F/ 57 to 79 °C
The RHA spacing is dependent on the alarm set-point. The unit is Rate-of-rise 12 to 15°F
listed from 135°F to 174°F. However as the temperature setting
Installation temperature range 32 to 100 °F / 0 to 38 °C
increases, the spacing decreases.
Operating relative humidity 0% to 93% (Non-condensing)
range
Alarm set-point RHA Spacing
Start-up time Max. 1 sec.
135 to 170 °F (57 to 76 °C) Max. 50 ft
Maximum number of 127
171 to 174 °F (77 to 79 °C) Max. 15 ft
addresses per loop
Maximum number of lighted 13
The system has a maximum of 13 LEDs that can be turned on simulta- indicators in alarm per zone.
neously. If the system already has 13 LEDs on, the RHA will operate
even though the LED will not illuminate. Color Eggshell White
Setting the Address Weight (without base) 73g (2.57oz)
Each addressable module, smoke sensor, heat detector and Dimensions (without base) Height: 1.50 in (38mm)
combination sensor/detector must have the address set before Diameter: 4.0 inches (99mm)
connecting the device to the SLC loop. The address is set using the Approvals / Listings UL, ULC, CSFM, MEA
hand held device programmer or the addressing feature on the control
Potter Electric Signal Company, LLC • St. Louis, MO • Cust Service: 866-240-1870 • Tech Support: 866-956-1211 • Canada: 888-882-1833 • www.pottersignal.com
PRINTED IN USA MKT. #8830018 - REV C PAGE 1 OF 2
06/13
RhA
Rate of Rise/Fixed Temperature
Heat Detector
Operation
The RHA is an analog/addressable sensor that uses one address on the Signaling Line Circuit (SLC) of a compatible fire alarm control panel.
The unit communicates with the control panel as it is polled. The LEDs flash every time the unit is polled and they will latch steady if the unit is
in an active status.
The RHA is a single sensor that may be used in a wide variety of applications for property protection. The RHA has a the rate of rise heat
detection to provide detection of an escalating fire. The unit has a sleek design and low profile for pleasing aesthetics. The temperature sensor is
protected within the mold of the unit to prevent accidental damage.
Compatible Bases
All bases will mount on a single gang, double gang, octagon, 4” square or mud ring electrical box.
Device Description
AB-4 4” Standard Base
AB-6 6” Standard Base
AIB 6” base with an isolator module included. The base is pre-wired with a pluggable jumper to the module.
ARB 6” base with a dual relay module included. One relay is rated for 8 amps at 240 VAC/30 VDC and the second is
rated for 2 amps at 240 VAC/30 VDC. The base is pre-wired with a pluggable jumper to the module.
ASB 6" base with sounder module included. Sound pattern is provided from external source. The base is pre-wired
with a pluggable jumper into the module.
PRINTED IN USA MKT. #8830018 - REV C PAGE 2 OF 2
06/13
