Scribd
Upload
513 views6 pages

BGP Routing Configuration Lab Using Packetnbsptracer

This document provides instructions for configuring BGP routing on three routers - R1, R2, and R3 - using Cisco Packet Tracer. It explains that BGP neighbors can be either IBGP or EBGP depending on if they are in the same or different autonomous systems. The steps show how to assign IP addresses, configure BGP on each router including neighbor relationships and networks, and test connectivity by pinging between PCs and verifying routes on each router.

Uploaded by

shinde_jayesh2005
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
513 views6 pages

BGP Routing Configuration Lab Using Packetnbsptracer

This document provides instructions for configuring BGP routing on three routers - R1, R2, and R3 - using Cisco Packet Tracer. It explains that BGP neighbors can be either IBGP or EBGP depending on if they are in the same or different autonomous systems. The steps show how to assign IP addresses, configure BGP on each router including neighbor relationships and networks, and test connectivity by pinging between PCs and verifying routes on each router.

Uploaded by

shinde_jayesh2005
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

bgp routing configuration lab using packet tracer

linuxtiwary.com/2018/02/19/bgp-routing-configuration-lab-using-packet-tracer

satish tiwary 19 Feb 2018

bgp configuration lab using cisco packet tracer

In this article I am going to show you how to configure bgp step by step.This
is a bgp configuration example lab showing bgp configuration using cisco
packet tracer.I will show you how to configure bgp routing protocols on cisco
router using three router.This is an example lab showing bgp
configuration.Here in This Lab I have taken 3 AS they are 1,71 and 79
respectively

BGP neighbors can be of two types:

IBGP neighbors – when two neighbors are in the same AS(Autonomous System);

1/6
EBGP neighbors – when two neighbors belong to different AS(Autonomous System).

You can Download bgp configuration Lab file: Click here to Download

Step 1:Draw BGP Topology Diagram.

Step 2: Assign ip address on each device as mentioned in Diagram.

2/6
Step 3: bgp configuration on Router R1:

R1(config)#router bgp 1
R1(config-router)#neighbor 172.16.0.2 remote-as 71
R1(config-router)#network 10.0.0.0 mask 255.0.0.0
R1(config-router)#exit
R1(config)#do write
Building configuration...[OK]
R1(config)#

Step 4: bgp configuration on Router R2:

R2(config)#router bgp 71
R2(config-router)#neighbor 172.16.0.1 remote-as 1
R2(config-router)#neighbor 172.14.0.2 remote-as 79
R2(config-router)#network 40.0.0.0 mask 255.0.0.0
R2(config-router)#exit
R2(config)#do write
Building configuration...[OK]
R2(config)#

Step 5: bgp configuration on Router R3:

3/6
R3(config)#router bgp 79
R3(config-router)#neighbor 172.14.0.1 remote-as 71
R3(config-router)#network 40.0.0.0 mask 255.0.0.0
R3(config-router)#exit
R3(config)#do write
Building configuration...[OK
R3(config)#

Step 6: bgp configuration Testing and troubleshooting.

For bgp testing we will ping both pc and check the network communication.

Now I am on PC2:

PC>ipconfig

PC>ping 10.0.0.2

Step 7: check bgp route on router R1:

R1#show ip route

Step 8: Check whether bgp protocols configure or not on Routre R1:

R1#show ip protocols

Step 9: Show BGP Status

R1#show ip bgp summary

Show bgp neighbors status:

R1#show ip bgp neighbors

Similarly we check bgp route on Router R2:

R2#show ip route

R2#show ip protocols

Similarly check bgp route on Router R3:

4/6
R3#show ip route

R3#show ip protocols

Interested candidate can also join our ccna online and classroom training program.

Watch Video At: https://youtu.be/J7QH_d6ZM-E

5/6
6/6

You might also like