IS0
INTERNATIONAL STANDARD . 299
Second edition
1987-04-01
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION
ORGANISATION INTERNATIONALE DE NORMALISATION
MEWYHAPOAHAR OPTAHM3A4MFl IlO CTAHflAPTM3A~MM
Machine tool tables - T-slots and corresponding
bolts .
iTeh STANDARD
- Rainerres
Tables de machines-outifs PREVIEW
B T et boulons correspondants
(standards.iteh.ai)
ISO 299:1987
https://standards.iteh.ai/catalog/standards/sist/3f57a413-630e-4268-b9db-
760bf948a149/iso-299-1987
Reference number
IS0 299: 1987 (E)
Foreword
IS0 (the International Organization for Standardization) is a worldwide federation of
national standards bodies (IS0 member bodies). The work of preparing International
Standards is normally carried out through IS0 technical committees. Each member
body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, govern-
mental and non-governmental, in liaison with ISO, also take part in the work.
Draft International Standards adopted by the technical committees are circulated to
the member bodies for approval before their acceptance as International Standards by
the IS0 Council. They are approved in accordance with IS0 procedures requiring at
least 75 % approval by the member bodies voting.
iTeh STANDARD PREVIEW
International Standard IS0 299 was prepared by Technical Committee
ISO/TC 39,
Machine tools. (standards.iteh.ai)
This second edition cancels and replaces the first edition (IS0 299ISO: 299:1987
19731, of which the
dimensions in inches have been deleted and to which clause 5 has been added.
https://standards.iteh.ai/catalog/standards/sist/3f57a413-630e-4268-b9db-
760bf948a149/iso-299-1987
Users should note that all International Standards undergo revision from time to time
and that any reference made herein to any other International Standard implies its
latest edition, unless otherwise stated.
0 International Organization for Standardization, 1987
Printed in Switzerland
INTERNATIONAL STANDARD IS0 299 : 1987 (E)
Machine tool tables - T-slots and corresponding
bolts
iTeh STANDARD PREVIEW
1 Scope and field of application except for the dimensions of bolts below 6 mm and above
(standards.iteh.ai)
36 mm for which there are no corresponding values, will form
This International Standard specifies, in millimetres, the dimen- the subject of an addendum. The corresponding values will en-
sions and spacing of T-slots for machine tool tables. ISO 299:1987 sure practical interchangeability between machines made in
either of the two measurement systems, as well as inter-
https://standards.iteh.ai/catalog/standards/sist/3f57a413-630e-4268-b9db-
It also specifies the metric dimensions of bolts to be used in changeability with existing machines in many cases.
these slots.
760bf948a149/iso-299-1987
For reference or fixing slots, there is no interchangeability from
one measurement system to the other, since the nominal
2 Dimensions of slots and bolts dimension, A, will not be identical in this International Stan-
dard and its addendum. ’
The dimensions of T-slots and of the corresponding bolts are
specified in table 1. The corresponding dimensions in inches,
1
IS0 299 : 1987 (E)
A.
0,3x4S" max.
Chamfer or
. .
radius I
E, F and G : 45O-chamfer height or radius
Table 1
I Slot
I
Bolt
I
/ A 1 min. -T- max. 1 min.
iTeh STANDARD PREVIEW
i max. 1 min. 7 max.- mtx. mix. rnZx- a ’ 1 ’ /
5 IO 11 35 4,5 866 IO 1 1 M4 9 3
6 11 12,5’ 5 (standards.iteh.ai)
6 11Or6 13 1 1 M5 IO 4
8 14,5 16 7 8 15 18 1 66 1 M6 13 6
IO 16 18 7 8 17’ ISO
21 299:19871 Or6 1 M8 15 6
12 19 21
https://standards.iteh.ai/catalog/standards/sist/3f57a413-630e-4268-b9db-
8 9 20 25 1 Or6 1 Ml0 18 7
760bf948a149/iso-299-1987
14 23 25 9 11 23 28 I,6 Ok5 I,6 Ml2 22 8
18 30 32 12 14 30 36 116 1 I,6 Ml6 28 IO
22 37 40 16 18 38 45 1.6
. 1 23 M20 34
- 14
28 46 50 20 22 48 56 116 1 2,5 M24 43 18
T
36 56 60 25 28 61 71 2,5 3 2,5 M30 53 23
42 68 72 32 35 74 85 2,5 116 4 M36 64 28
48 80 85 36 40 84 95 2,5 2 6 M42 75 32
54 90 95 40 44 94 106 2,5 2 6 M48 85 36
Slots : Tolerances on A : H12 for fixing slots,
H8 for reference slots.
Bolt : Tolerances on a, b, c : usual tolerances for bolts and nuts.
NOTE - Although assembly by bolts is the only one shown, any other device complying with the same interchangeability conditions may be regarded
as being in agreement with this International Standard.
3 Spacing of slots table or plate and to the number of slots required for its use, ad-
ditionally taking into account the advantage of providing,
For each dimension A of standardized T-slots, three or four whenever possible, symmetrically arranged slots about a me-
values of pitch Pare given in table 2, from which the manufac- dian slot which is usually machined as a reference slot. When
turer is advised, unless there is a justifiable reason to do other- there is an even number of slots, the reference slot shall be
wise, to choose the one best fitted to the dimensions of a given clearly identified on the machine table itself.
IS0 299 : 1987 (El
Table 2 4 Tolerances on pitches of T-slots
Table 3
Pitch, P Tolerance
20 and 25 I!I 0,2
32 to 100 Ik 0,3
125 to 250 ItI 0,5
320 to 500 + 0,8
NOTE - The tolerance on the pitch of any T-slot is non-cumulative.
Slot width, A Pitch, Pl)t 2)
5 20 - 25 - 32
6 25 - 32 - 40 5 Designation
8 32 - 40 - 50 The T-slots and the corresponding bolts shall be designated by
IO 40- 50- 63 the nominal dimension of the bolt thread, e.g. MlO.
12 (4-O)- 50 - 63 - 80
14 (50) - 63- 80- 100
18 (63) - 80 - 100 - 125
22
28
iTeh STANDARD PREVIEW
(80) -
100 -
100 -
125 -
125 - 160
160 - 200
36 (standards.iteh.ai)
125 - 160 - 200 - 250
42 160 - 200 - 250 - 320
ISO 299:1987
48 200 - 250 - 320 - 400
https://standards.iteh.ai/catalog/standards/sist/3f57a413-630e-4268-b9db-
54 250 - 320 - 400760bf948a149/iso-299-1987
- 500
I) Where values of P greater or less than those given in table 2 are
absolutely necessary, they shall be chosen from the values of the RIO
series of preferred numbers; where intermediate values are required,
they shall be chosen from the values of the R20 series.
2) Where possible the pitches shown in parentheses should be
avoided owing to the smaller thickness of material between the T-slots
(prnin - 4laJ
3
iTeh STANDARD PREVIEW
(standards.iteh.ai)
This page intentionally left blank
ISO 299:1987
https://standards.iteh.ai/catalog/standards/sist/3f57a413-630e-4268-b9db-
760bf948a149/iso-299-1987
iTeh STANDARD PREVIEW
(standards.iteh.ai)
This page intentionally left blank
ISO 299:1987
https://standards.iteh.ai/catalog/standards/sist/3f57a413-630e-4268-b9db-
760bf948a149/iso-299-1987
IS0 299 : 1987 (E)
iTeh STANDARD PREVIEW
(standards.iteh.ai)
ISO 299:1987
https://standards.iteh.ai/catalog/standards/sist/3f57a413-630e-4268-b9db-
760bf948a149/iso-299-1987
UDC 621.9.06-229.311.
Descriptors : machine tools, machine tables, work-holding fixed tables, T slots, bolts, dimensions.
Price based on 3 pages
